Search Documents

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By R. F. Mehl, M. L. Swanson, J. P. Hirth, G. M. Pound

The sorption of zinc in a-brass was investigated. By analyzing the elliPtically polarized light reflected from the surfaces of a-brass solid-vapor couples, their optical constants and surface compositions were determined. It was shown that the surface compositions approached an equilibrium value exponentially with time. The bulk diffusion coefficient, surface diffusion coefficient and condensation coefficient for a-brass solid-vapor couples were calculated near 350°C from the experimental results. It has been assumed during various diffusion experiments with bimetallic solid-vapor couples (Dunn,1 Seith and Kraus,2 Jenkins,3 Balluffi and Seigle,4 and others) that the surface composition of such couples reaches its equilibrium value immediately. Although this assumption is probably valid at elevated temperatures, it is certainly not expected to be confirmed at lower temperatures.* consequently, it was decided that a fundamental experiment, designed to solve this problem as well as to examine all aspects of bimetallic sorption, would be the investigation of the rate of approach to equilibrium of the surface composition of solid-vapor couples. The sorption (i.e., adsorption, absorption, and desorption) of metals is obviously dependent on the state of the metallic surface and substrate. Much recent theoretical8"9 and experimental10-12 work on condensation and evaporation of pure metals has shown that the surface contour in atomic dimensions is a critical factor in sorption, so that any deformation or contamination13,14 of the surface exerts a profound influence. It is also known that absorption or diffusion occurs much more rapidly along grain were and in other deformed regions. Thus an effective sorption experiment must utilize a strain-free and clean surface, or at least a clearly defined and reproducible surface state. A mechanically polished surface is in a highly deformed17-l9 state. Because the degree of this deformation is uncertain, it is clear that for most experimental purposes a strain-free (i.e., etched, chemically polished, or electropolished) surface is desirable. Although adsorbed gas molecules on metallic surfaces are unavoidable even in the highest vacuum,20 oxide films can in some cases be removed by suitable vacuum annealing. Electrolytically polished and annealed surfaces, being relatively without strain, smooth and free of bulk oxides, were considered adequate for the present sorption experiments. Measurement of the surface composition of a solid-vapor couple presents a unique problem. Since experiments to determine the approach to equilibrium of the surface composition must be performed at temperatures where diffusion is very slow, solute penetration is so small that conventional analytical methods are unsuitable. An optical reflectivity method utilizing a polarization spectroscope was employed because of the relatively small penetration (~200A) of visible light in metals. By this method, elliptically polarized light reflected from the metal surface was analyzed and compared with that reflected from samples of known composition. The a phase of the copper-zinc system was

Jan 1, 1962

By A. Kaufmann, B. Cullity, G. Bitsianes

T0 determine the bulk of the phase diagram, techniques for melting, thermal analysis, heat treatment, metallography, and X-ray diffraction that have already been described were used.' It proved difficult to get definitive results for most of the alloy system because of the large number of compounds, their high melting points, and their extreme brittle-ness which made metallography difficult. The final phase diagram, essentially as shown in Fig. 1, was issued with considerable trepidation.' The phase relationships at the two ends of the system were defined with satisfactory accuracy. In the central region between U,Si, and USi, there was great uncertainty concerning the melting points and even the composition of the compounds. At the uranium end of the system, it is quite clear that a eutectic exists at about 985 °C and approximately 8 or 9 atomic pct Si. The a-to-8 transformation is not appreciably altered by silicon, but the 8-to-y transformation is raised to about 795°C. There is appreciable solid solubility in y-uranium, as demonstrated by the micrographs of Fig. 2. The occurrence of the E phase was not suspected at first, since the alloys as melted and furnace cooled gave no X-ray diffraction or thermal arrest indication of it. However, suitable metallography revealed a rim around each of the compound particles as shown in Fig. 3. Heat treatment above 600°C revealed that the rim was another phase which formed by peritectoid reaction between uranium and U,Si,. This reaction proceeds slowly and it is difficult to get it to go to completion. Consequently, there is some uncertainty concerning the exact composition of P and the exact peritectoid temperature. On the basis of various metallurgical studies, it was decided that the most probable composition for t was about 23 atomic pct Si. Metallographic examination shows the closest approach to a single phase at this composition. Likewise, density and hardness measurements of heat-treated alloys shown in Figs. 9 and 10 show a change in slope at 23 pct Si. This is revealed most clearly by plotting the difference in hardness or density between chill-cast and heat- treated alloys as shown in Fig. 4. Zachariasen2 was able to index the diffraction lines of P and to determine the arrangement of the atoms in the unit cell. He concluded that the composition must be US. However, it is felt that the metallurgical studies are reliable and that Zachariasen's X-ray work does not furnish positive proof that the P phase exists exactly at the stoichiometric composition U3Si. There are many instances in alloy systems where a phase does not occur at the composition dictated by the molecular structure. It is possible that the chemical analyses used in the present work were subject to some systematic error. This seems unlikely, however, since recent work in several laboratories seems to show excess compound at 25 atomic pct Si.

Jan 1, 1958

By J. Suiter, H. F. Ryan

H. F. Ryan and J. Suiter (CSIRO)—In this paper the authors have presented "a physical model which has as its central hypothesis the solution strengthening of regions along grain boundaries in the order of tens of angstroms thick", and their calculations have used 40Å as the zhalf-width of this boundary region. Selection of this value by the authors suggests that they were unaware of a number of recent field-ion microscope observations of grain boundary structures (e.g., Refs. 29 and 30). The accompanying figure, Fig. 9, shows a portion of an ion micrograph of a tungsten specimen containing a grain boundary, and the regular arrangement of atoms in various crystal planes in each grain can be seen, except in the boundary zone which is not more than two atom diameters in width. Since it is expected that solute atoms will segregate only to the region where the lattice is disturbed, it would seem that a value of 4Å for the half-width of the boundary region would be more appropriate than the value of 40Å assumed by the authors. If the former value is used in Eq. [8] of their paper to obtain curves showing solute concentration in the grain boundary as a function of temperature, the resulting curves differ significantly from those obtained by the authors. Although there are only relatively slight changes in the regions corresponding to higher temperatures (i.e., grain boundary concentrations of approximately 1 at. pet), at lower temperatures the curves are no longer realistic. For example, the curve corresponding to u = 7000 cal per mole gives a solute grain boundary concentration in excess of 100 pet at a temperature of approximately 360°K, and "flattens out" at a grain boundary concentration of about 300 pet! Similar results are obtained with each of the other curves. Ion microscopy of dilute solid-solution alloys has shown that solute atoms give rise to image points which in most cases are of higher intensity than those of the solvent atoms.31 If the same behavior occurs when the solute atoms are present in much lower concentrations then ion microscopy should provide a sensitive tool for studying the segregation of impurities to the grain boundary regions. Although many grain boundaries in tungsten have been examined after different thermal and mechanical treatments, there has not been, as yet, any systematic study of such segregation. In general the micrographs show no clear indications of marked grain boundary segregation, but occasionally areas are found where the grain boundary contains an appreciable number of image points of high intensity in a very narrow zone, see Fig. 9. If it is assumed that these correspond to impurity atoms then it is possible to estimate the impurity concentration both in the grain boundary and within the body of the grains. Application of this method (to a larger area

Jan 1, 1965

* The greatest and richest iron ore body in the world was discovered by U. S. Steel in Venezuela in April 1947, and is disclosed for the first time in this issue (p. 178), One solid mountain of ore, Cerro Bolivar, will furnish more tonnage than the famous Hull Rust pit at Superior has, or can produce. Total resources are on the order of 2 billion tons plus. Big Steel is now moving with great speed on construction to bring out this ore, and 10 million tons are scheduled for shipment into Baltimore and Birmingham by late 1952. This ore will arrive at, Pittsburgh at a price lower than present natural ores from Superior. The Venezuelan properties will be completely mechanized. •U. S. Steel and independent companies are embarking on a taconite beneficiation program of tremendous proportions, which must be speeded to completion in the 1950's (see p. 185). By 1960 over $l.2 billion dollars will be spent on Venezuela, taconite, and Labrador to solve the United States iron ore crisis. In addition, U. S. Steel will spend another $300 million plus for a new steel mill at Trenton, N. J., before 1955. •The Deister Concentrator Co. gave $500 to the 1950 Coal Division Scholarship Fund. •Howard N. Eavenson, in analyzing the bituminous coal situation (see p. 193), suggests that anti-trust laws be extended to labor unions, disinterested trustees to administer pension funds, begin pension funds now and stop the collection of all "check-offs" for union dues or funds. •Minerals and metals worth 13.9 million dollars were produced in the United States in 1949, Secretary of the Interior Oscar L. Chapman announced. Although this value was 11 pct less than in 1948, it was the second greatest in history. Nonmetallics was the only major group that in 1949 equaled the 1948 production high. Mineral fuels decreased 12 pct and metals 15 pct. • Prospects for making gas from coal are seen to be unattractive by the Pittsburgh Consolidated Coal Co. because the success of operation depends on price and supply of coal which presently are not attractive. The company has shut down its gasification plant at Library, Pa. * Economic prospects for the immediate future in the United States are good and business probably will continue at its present high levels throughout at least the early part of 1950, Secretary of Commerce Charles Sawyer said in his year-end report to the White House based on his personal survey of business conditions. •A 467-ft well 34 miles north of Rock Springs, Southwestern Wyoming, is said to be flowing a 5 pct solution of nearly pure trona (sodium carbonate) at the rate of 10,000 barrels a day. Trona, natural soda ash, is mined for the chemical trade at Searles Lake, Calif., and from about 1500 ft underground near Green River, Wyo., and has been in short supply. •The AEC is "very much interested" in a discovery of radioactive material that has been made in Baraga County bordering Lake Superior in the Upper Peninsula of Michigan, reported F. G. Pardee, Michigan State mining engineer. The material has been identified as uranium oxide in the form of pitchblende or uraninite. The discovery, made by a geologist of the Jones & Laughlin Ore Co., is the only instance in which the commission has certified samples of Michigan rock.

Jan 2, 1950

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By T. Vasilos, J. T. Smith

THE mechanism of pressure sintering, or hot pressing, for ceramic materials, has been investigated by several researchers.1-8 Plastic flow has been suggested as the rate-determining mech-anism1,2 while grain boundary sliding3,4 and fragmentation processess have been found controlling in other studies. Vasilos and Spriggs5,6 have reported that pressure sintering occurs by a diffusion-controlled mechanism. For the pressure sintering of metals, investigations with lead7 and with tin6 have not identified the operative mechanism during consolidation of these powders. This note reports the results of a pressure sintering study initiated to determine the mechanism controlling the densification of spherical copper powder. Temperatures of 300°, 400°, 500°, and 600°C at 2500, 5000, 7500, and 10,000 psi pressures were investigated. The copper powder for this study was obtained from Metals Disintegrating Co., Elizabeth, N.J. The minimum purity was reported to be 99.9 pct. The powder size was -325 mesh and a lineal analysis showed the average size to be less than 1 p. An alumina die body and punches were employed. Graphite spacers were placed between the copper powder and the punches before pressing. It was expected that the graphite would form carbon monoxide with any entrapped air and form a reducing atmosphere within the die cavity. This condition was generally realized during pressing although a minor amount of oxidation occurred at 500" and 600°C. The oxide particles were located randomly in the pressed samples and were not considered to influence the densification process. Calibration tests showed the temperature of the copper pellet to be about 20°C less than the die wall temperature, probably resulting from heat losses through the punches. This difference was compensated during the experimental pressing operations. The hot pressing equipment employed for this work has been described by Spriggs et a1.9 and was calibrated with a Baldwin-Lima-Hamilton load cell. Travel of the punches was monitored with a dial indicator showing increments of travel to 0.0005 in. Relative density was calculated at selected time intervals for a known copper weight, punch travel, and die diameter. The accuracy of this calculation was *1 pct. Average grain size after hot pressing was obtained by lineal analysis. Typical densification curves are presented in Fig. 1 and Fig. 2 where relative density is plotted vs log time as a function of applied pressure for the 300" and 600°C pressure sintering temperatures, respectively. The curves for 400" and 500°C were similar to those at 300°C and consequently are not shown. The curves at 300°C as well as 400" and 500°C do not show an end-point or limiting density for a particular applied pressure. At 600°C, a density in excess of 95 pct of theoretical has been reached such that further densification is extremely slow for the 5000, 7500, and 10,000 psi pressures. It is suggested that further densification at these pressure levels may be retarded or prevented by discontinuous grain growth, by entrapped gases, and by other microstructural limitations as described by Cob1e.10 The curve for 2500 psi hot pressing pressure is a straight line over the time interval although a slight change in slope may be occurring at the last time intervals. The plastic flow models,1,2 derived for hot pressing, predict the existence of an end-point (or limiting) density dependent on the yield point of the material at the temperature of interest. The yield stress of copper at a 0.005 strain level has been

Jan 1, 1965

By L. K. Eigenbrod, F. Notaro

Enactment of Public Law 91-173 (Federal Coal Mine Health and Safety Act of 1969) has placed new responsibilities on the mining industry. The new law, aimed at eventually solving the problem of pneumoconiosis, sets new respirable dust standards at 2 mg per cu m. Techniques employed to date have been shown to lack total effectiveness in meeting the prescribed standards. Since it is possible that even the new standards will eventually have to be lowered to effectively attack the medical problem, the need for new and more reliable methods of assuring clean respirable air will intensity. This paper presents, in a preliminary manner, both the present technical capability and growth potential of cryogenic technology for supplying miners with clean breathing air. Work with two sizes of prototype supplied-air (cryogenic-liquid) respiratiors in Union Carbide's Fawn Coal mine, will be described. Other potentially fabricable systems will be discussed and a preliminary assessment made of the potential cost of introducing cryogenic air breathing systems in coal mine service.

Jan 1, 1972

By Donald E. Crowell

In the fall of 1969, ASARCO and Newmont Mining Co. began the design of the 700tpd concentrator at their Black Cloud shaft located near Leadville, Colo. The concentractor would treat by flotation a Pb-Zn-Ag ore containing minor gold values. Flowsheet design was based on laboratory test work performed at the Minerals Research Testing Laboratory of ASARCO. Since the concentrator is located at an elevation of 11,000 ft, cold weather was a major factor in design considerations. The original capacity was designed as 700 tpd but for various reasons an ultimate capacity of 1,000 tpd was desired. This necessitated special consideration in the design of several areas, particularly the grinding circuit. The grinding circuit chosen was a single 9 X 12 ball mill operating in closed circuit with one 20-in. cyclone. The ball mill will operate at low speed and as an overflow type originally. The mill can be speeded up and converted to grate type for handling the larger tonnage when required. Thickeners and filters were oversized and space was left for additional flotation cells in order to handle the increased tonnage in these areas. Pumps were sized so that they could handle the increased tonnage by increasing their speed. Construction began in May 1970; the Black Cloud concentrator went on-stream in April 1791.

Jan 1, 1974

By K. Matsuda, H. Tanaka, M. Mamiya, H. Majima

Copper cementation was studied from both thermodynamic and kinetic aspects. The temperature effect of copper cementation, which has been recognized as an anomalous result, and the rate enhancement phenomenon observed after the initial linear step are, in particular, focused in this work. The main results obtained are as follows; 1) Free energy changes of copper cementation reactions, calculated by the use of the "Correspondence Principle" of Criss and Cobble are rather insensitive to temperature. 2) A Flow-cell assembly consisting of a special cupric ion electrode, a calomel electrode and a potentiometer is particularly useful for the continuous measurements of copper cementation rate. 3) Two first-order reaction rate constants for the CU2+- Fe system were successfully determined by the use of the flow-cell assembly. 4) Activation energies determined for the initial rate and the 9 maximum rate of CU2+ - Fe system are both 4.6 kcal/mole. This fact suggests that the mechanisms of the initial reaction and the final reaction are essentially the same and both reactions are rate controlled by the diffusion in a boundary layer. The difference in the rate constants of them may fie explained by the effect of the nature of surface deposits. 5) Qualitative explanation of the rate enhancement phenomenon from the initial rate was successfully made by applying Bockris "Penetration Model."

Jan 1, 1976

By J. F. Nester, J. B. Schroeder

COMPOUNDS of rare-earth and iron-group elements are of technical interest because of their unusual magnetic properties. To date, however, all magnetic measurements1-4 have been made with polycrystalline, often polyphase, samples. For the measurement of anisotropic properties, single-crystal samples are necessary to avoid the averaging effect of randomly oriented grains. The purpose of this note is to describe a technique with which we have grown relatively large single crystals of YCo5, NdCo5, DyCo5, and "YFe9". Crystal growth of these materials is complicated because: 1) the binary equilibrium diagrams are, in general, not well-established; 2) in those cases where phase-equilibrium data are available, the compounds of interest are generally formed by peritectic reaction; 3) the molten component metals are chemically very reactive, making contaminaticn of the melts by the crucible material a serious problem. Techniques such as arc or levitation melting followed by strain annealing have been tried5)' in the past with these materials, but with little success because of the peritectic reactions and the inherently poor process control. For this reason we chose to use the zone-melting technique of Mason and cook7 for our work, since past workers8 have had some success in preparing single crystals of peritectic compounds by this method.

Jan 1, 1965

By Edgar S. Cook

The Warwick furnace at Pottstown, Pa., constructed for anthracite fuel, is, as may be remembered, 554 feet high, with 15; feet bosh. The actual working height from stock-line to bottom is only 474 feet, the bell-and-hopper taking up 8 feet. During the year 1886 we used mixed fuel, in the proportion of three-fourths anthracite and one-fourth coke. The total product of iron was 30,6299 tons of 2280 lbs., being a weekly average of 589 tons, including all ordinary and extraordinary stoppages. Deducting the latter, the weekly average would be about 600 tons. The fuel-consumption for the year was 1.2 tons per ton of iron, while the ore-mixture yielded 52 per cent. of iron. For about two months during the summer of 1887 we were obliged to run on anthracite exclusively, owing to the Connellsville coke strike. In the fall of 1885, in relining the furnace, the crucible had been built 8 feet 9 inches in diameter, with the view of using regularly one-quarter of coke (the largest previous diameter having been 7 feet 5 inches), and we felt somewhat apprehensive of the results when compelled to use anthracite only. The average of seven weeks' run on coal, as compared with the average of the seven corresponding weeks of 1886 (using one-quarter coke), was as follows:

Jan 1, 1889

Hunkered up against the spine of the Andes in a tight valley where natural refuge from avalanche hardly exists is the daring Rio Blanco project of Cerro Corp. The deposit here was found in 1904, but nature has foiled all previous attempts to open it. To an experienced mountaineer or a highway engineer with mountain experience, the avalanche hazard in the valley of the Blanco river would be immediately apparent. The collar shaft is at the head of the valley at an elevation of 3600 m and for 12 km down the valley there is no space on the floor for building very much; the dissected rock walls are roadways for avalanches and even a highway could not be maintained sufficiently passable. This is the proposition taken on by the Cerro Corp. Chilean National Decree #1699, passed on December 9, 1966, signified "Go" to the Compania Minera Andina, a company whose shares are held 70% by the Cerro Corp. and 30% by the government of Chile. The orebody, although only partially delineated, contains proven reserves of 120 million tons of ore averaging 1.58% Cu. When the operation comes on stream in the last quarter of 1970, it will be at the rate of 11,000 tpd. Annual production will be 65,000 tpy of recoverable copper in concentrates.

Jan 11, 1969

Long range expansion plans begun in 1966 by The International Nickel Co. of Canada, producer of over 50% of the free world supply of the white metal, are so mammoth as to give rise to the speculation that something might have to burst at the seams. From an annual level of capital expenditure of $35 to $70 million, the company jumped in 1967 to $145 million in new capital investment and will come close to $200 million in 1968. Inco expects to spend $700 million in the next five years, beginning in 1968, for new mines and surface facilities in Canada. The program involves the opening of nine new mines within the next 3 1/2 years, expansion of producing mines, and construction of new plants and modernization and expansion of established ones to process the increased ore production. Beyond this, the company is committed deeply in developing new sources of nickel abroad. Any one of these new projects, if proven economic, would necessitate expenditures of about $100 million or more. For Inco, the economic strain was relieved without a rupture this spring when Henry S. Wingate, company chairman, reported' at the stockholders annual meeting that $150 million had been raised by the sale of bonds. This marked the first time in 32 years that the company had gone into debt.

Jan 10, 1968

By Byron B. Morton

NICKEL-BEARING alloys are associated with petroleum in the fields of exploration, production, and refining. In the first- named field the geologist of today makes use of such instruments as the seismograph, torsion balance, and magnetometer, the selection of proper alloys and metals for the manufacture of which is an important matter. Nickel-bearing alloys are useful for parts that require resistance to corrosion or that must have non-magnetic properties. Where special co- efficient of thermal expansion are de- sired, they are obtained by using alloys high in nickel (20 to 60 per cent), since, by varying the nickel contents, alloys can be obtained ranging fro111 "Invar", with a low expansion between -40 and 175 cleg. F., to those with coefficients of expansion exceeding that of steels. The latter are obtained by additions of chromiurn to the alloys. Alloys containing 50 to 80 per cent of nickel, which possess high magnetic permeability, find application in certain instruments where this property is important.

Jan 1, 1935

By AIME AIME

No democracy such as ours, can ever be prepared for war, because we could never conceivably be the aggressor. The aggressor prepares in secret, designs his new tactics, and invents and makes new equipment and selects the time to strike. If a democracy prepare done year and the war came later, all that it had one would have to bed one over. All that England has today in the way of effective armament has been invented, designed, made, and the crews trained since the war began, because the totalitarian aggressor introduced new types of equipment and new techniques.

Jan 1, 1941

By T. B. Massalski, Horace Pops

Martensitic transformations were observed by optical metallography and electrical-resistivity measurements during cooling at cryogenic temperatures of the bcc pr-phase Au-Zn alloys. The com-position dependence of the MS, MF, AS , and AF temperatures have been determined. It is concluded that the martensitic platelets which grow mainly in the lengthwise direction and which are associated with a very small temperature hysteresis are "thermoelastic" martensite. In some cases the observed structure seems to have no definite crys-tallographic habit or consists of a mixture of- plates and broad transformed areas. THE majority of the bcc /3-phase alloys in systems of copper, silver, and gold with zinc and cadmium are unstable at low temperatures and undergo a transformation upon further cooling into another structure. A large number of such transformations are martensitic. The composition dependence of the Ms temperatures has been determined and reported for CU-~n,' Ag-Cd,' and AU-C~~ alloys. The 50 at. pct ordered Au-Zn p' alloy has been reported by Jan and pearson4 to transform martensitically at 58°K in connection with their study of the de Haas-van Alphen effect The p' phase in the Au-Zn system has the ordered CsC1-type structure. The phase field is shown in Fig. 1: it has the typical V shape which is characteristic of all copper-, silver-, and gold-based binary /3-phase alloys. There appears to be no a priori reason why the transformation should be limited to the equiatomic composition and the availability of a cryogenic stage for optical metallography5 has permitted studies down to the liquid-helium temperature of a series of alloys in this system. EXPERIMENTAL PROCEDURE Predetermined weights of 99.999 pct pure gold and zinc were melted and cast under a partial atmosphere of helium in sealed quartz capsules. Thorough mixing of the molten metals was achieved by vigorous shaking, followed by a rapid quench into a brine solution. All ingots were homogenized at 640°C for 4 days. The loss in weight was usually less than 0.04 wt pct and was assumed to be due to

Jan 1, 1965

By William P. Blake

This camp is just now startled by the alarming suggestion that unless there shall speedily be an appreciation in the value of silver, and a decrease in the cost of salt, it will be prudent business policy to close the Alice mines and mills until the conditions of production are more favorable. Such an event would be a great blow to the prosperity of Butte. It would throw some hundreds of men out of employment, and it might lead to the adoption of the same policy by other companies, which, like the Alice, have not been able to pay dividends to their shareholders for a long time. The question arises, and becomes emphatic: If, under the present adverse conditions, the mines and mills cannot be made to pay a proper profit, why should they continue to be worked ? The owners mentally ask: Shall we go on exhausting our mines, pouring out a stream of silver for the maintenance of the community, and the support of the rail ways, or shall we husband our reserves, withdraw the miners from our slopes, and wait for more favorable conditions ? This is the impending question, and all concerned dread to meet and answer it. Let us briefly review the situation and forecast, if possible, what the solution of' the problem will be. It must be understood that the discussion does not include, or refer to, the immense copper-producing interests of the camp, which may or may not be upon a very much more satisfactory basis. It will be confined chiefly to the operations of the Alice company, sta tistics of which are at hand, without involving the other silver com panies in the conclusions beyond those inevitable from well-known facts, patent to all. There are at present in Butte and in its vicinity in the principal mills an aggregate of 290 stamps dropping upon silver-ores: Alice,...........80 stamps. Moulton,. .........40 " Lexington,...50 " Silver Bow,.........30 " Blue Bird,..........90 " The Alice mills at present, with their 80 stamps, devour, in round numbers, from 100 to 120 tons a day. The actual amount

Jan 1, 1888