Search Documents

By Norris Johnston, Carrol M. Beeson

For many years the permeability of reservoir sands has been measured by flowing air through a cleaned and dried core sample. This differs from the true reservoir permeability in one important respect: the rock particles in the reservoir are surrounded by interstitial water, not air, and their physical shape and condition of hydration are greatly dependent thereon. Permeability as defined must be measured with a single-phase fluid. Since no means exist for removing the oil and gas from a core sample by simply flowing water through it, the sample must be cleaned and then resatu-rated with water before testing. The present discussion attempts to show that after the cleaning process a considerably different permeability is determined with salt or fresh water than is obtained with air. The postulate is made that the salt-water permeability is probably closer to the true reservoir permeability than is the measurement with air. This is discussed in relation to both physically possible and economically feasible measuremerits. Data On more than 1200 core samples are given to show the nature of the effects observed, and a plea is made for others to consider water permeability measurements as a routine necessity, eventually replacing air permeability in regions where the differences are great. Introduction Permeability is defined1 as a "a measure of the capacity of a porous medium to transmit fluids, when there is no interaction between the solids and the fluid." Darcy's law of liquid flow in porous media states: kA?P QµL/A?L [I] where Q represents milliliters of liquid of viscosity p centipoises passed per second through a porous medium of permeability k darcys and cross-sectional area A sq. cm. under a pressure gradient ?P/L atmospheres per centimeter, the flow being understood to be laminar or viscous, not turbulent. This equation defines the darcy. For the case of radial flow in a uniform sand, such as usually exists in the neighborhood of a well in an oil or gas sand, Darcy's law becomes:2 Here h is the net sand thickness in feet, Pe and Pw are pressures at the drainage radius4 and well radius, and re and rw are these radii, respectively. The productivity index3 is defined as the barrels of liquid produced per day per pound per square inch mean pressure differential between ferences and well bore, and is thus: By further definition, the specific productivity index is: or in terms of practical units, and allowing for shrinkage:

Jan 1, 1945

By Carl F. Floe, John Chipman

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By John Cogan

Field observations were made of rock phenomena in shale, dolomite, and fractured quartzite in the Burgin Mine, Eureka, Utah. Draft closure rates were measured with extensometers and convergence gages. In addition the effects of hydraulic props upon the retardation of closure was also monitored. Drift closure rates were found to be constant and to vary between 0.32 x 10-8 min-1 for dolomite and 23.8 x 10-8 min-1 for soft shale. The installation of props set at constant load served to retard the closure rates. General results show closure to occur at a constant rate for all cases, to be non-uniform around the drift openings, and to be increasingly retarded toward a zero rate by increases in prop load.

Jan 1, 1979

By David J. Mack, Dennis R. O’Boyle

The mechanical properties of three polycrystalline intermediale Phases that have the y bvass structure were measured in compression between 400° and 900°K. At the lower testing temperatures— termed Region I— no plaslic deformalion occurred prior to brittle fracture. A1 higher temperatuves— lermed Region III—the three phases deformted plaslically for all strain rules from 1.5 to 36.0 x 10-4 sec-1. The homologous temperature for the inilialion of plaslic flow increased in the same order as tile atomic size difference between atoms in each plmse (0.50Tmp for y AgZn, 0.62Tmp for y CuZn, and 0.76 Tmp for y CuCd). The increased flow resistance oj. y CuCd above 0.50Tmp is explaitzed in terms of the more random arrangement of copper and cadmiwn atoms on the laltice sites of&apos; the y bvass slrilctlire. Plaslic deformation of the three intevmiediate phases in the smooth plaslic flow region appears to be controlled by oacancy-induced dislocation climb. RESULTS are reported in this paper on the mechanical properties of three binary intermediate phases having the complex cubic y brass structure (D82, 143m) containing fifty-two atoms in the unit cell. The structure of the prototype y brass phase, y CuZn, was first analyzed by Bradley and Thewlis&apos; based on the X-ray work of Westgren and Phragmen.2 The y brass structure can be visualized as an arrangement of twenty-seven body centered cubes (3 by 3 by 3) into a unit cell containing fifty-four atoms. From this cell the center atom and the four corner atoms are removed and the remaining fifty-two atoms are slightly displaced, resulting in the y brass structure. Approximately thirty-five binary intermediate phases that have an electron to atom ratio of 21:13 have been reported to form the y brass structure. The three y brass intermediate phases selected for this study are formed from elements in groups IB and IIB of the first and second long period. Each compound exists over a composition range that includes the stoi-chiometric composition A5BB (Cu5Zn8, Ag5Zn8, Cu5Cd8). y CuZn (a0 = 9.944A) has solubility limits extending from 57 to 67 at. pct Zn at 500°C apd melts peritecti-cally at 834°C; y AgZn (a0 = 9.326A) has a solubility range from 58 to 63 at. pct Za and melts peritectically at 661°C. y CuCd (a, = 9.596A) melts congruently at 563°C and has a maximum range of solubility extending from 58 to 64 at. pct Cd. In order to minimize coring and microporosity during solidification, the composi- tion of the compounds that form peritectically (y CuZn and y AgZn) was chosen so that the temperature difference between the liquidus and the solidus is only a few degrees centigrade. In selecting y brass compounds for this study, phases were avoided that contained a transition element or that had an electron to atom ratio greater than 1.70. Hume-Rothery et a1.3 has observed that, when the electron to atom ratio of y brass intermediate phases exceeds 1.70, atoms begin to drop out of the unit cell to maintain a constant electron to unit cell ratio. EXPERIMENTAL PROCEDURE Each of the three intermediate phases was prepared from elements having a purity >99.999 pct. Only trace quantities of impurities (<0.0001 pct) were detected by spectrographic analysis of the four elements. A master alloy of each compound weighing approximately 130 g was prepared by melting the elements in evacuated sealed quartz tubes heated in an electric furnace. Specimens having the desired diameter for the mechanical property measurements were obtained by remelting the master alloy in a Vycor tube under argon and drawing specimens from the melt into 4-mm-diam quartz tubes. To obtain a smooth surface on specimens drawn from the melt, the inside of the quartz tube was coated with a thin layer of graphite formed by thermally decompositing acetone. All specimens were imbedded in sealing wax and cut to the proper length with a diamond-impregnated cut-off wheel. The individual specimens (4 mm diam by 8 mm long) were then sealed in evacuated Pyrex tubes and homogenized at 500°C for 72 hr. Chemical composition, variations over the length of the rod (10 cm long) were generally less than 0.2 pct and the analyzed composition differed from the desired composition by less than 0.5 pct.4 Metallographic evaluation of the specimens after homogenization showed no evidence of a second phase in any of the compounds. The average grain size of the specimens after homogenization was 1 to 2 mm. All mechanical property measurements were carried out in an argon atmosphere using a compression apparatus described previously.5 Prior to applying the load to the specimen, the test apparatus was evacuated, back-filled with argon, and heated to the test temperature for 20 min to establish thermal equilibrium. EXPERIMENTAL RESULTS Mechanical properties measured as a function of temperature and strain rate for each of the three y brass phases were similar. From room temperature to the ductile-to-brittle transition temperature, only elastic deformation was observed prior to fracture.

Jan 1, 1968

By J. D. Miller, A. Cortez, J. Hupka

The separation efficiency of the hot water digestion-flotation technique used for bitumen recovery from various domestic tar sands was evaluated. Bitumen viscosity was found to be the most important tar sand property in determining the success of the bitumen separation. Bitumen viscosity of the tar sand war controlled by changes in digestion temperature and/or changes in diluent (kerosene) addition. Complete and uniform dilution of the bitumen phase was achieved by providing a sufficient presoaking, or penetration time, for a given tar sand type. For all the tar sand samples tested, an excellent correlation was obtained between the coefficient of separation and the bitumen viscosity. To achieve a satisfactory coefficient of separation, it was found that the bitumen viscosity must be reduced below 1.5 Pa.s (16 P) at the temperature of digestion. This was the case regardless of the tar sand type, grade, or origin.

Jan 1, 1984

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,&apos; Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o&apos;s. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze&apos;s (and McAdam&apos;s) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,&apos; Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o&apos;s. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze&apos;s (and McAdam&apos;s) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By Dorsey Lyon

INTRODUCTION THE electric furnace has always been found to be especially adapted to melting, refining, and finishing processes throughout its gradual acceptance by metallurgists, as a practical apparatus for conducting metallurgical operations. In the steel industry, the electric furnace is firmly established in the manufacture of steel of the highest grade, equal to crucible steel. For the production of the cheaper grades of steel in large tonnage, the electric furnace gives a higher-grade product than the open-hearth or converter, but due to the high cost of power prevailing in steel centers, considered from the electric furnace standpoint, it is not economical to produce tonnage steel in the electric furnace. As a refining and finishing agent for open-hearth or Bessemer steel, the electric furnace has had some degree of success in the production of tonnage steel. After a study of the use of the electric furnace in the steel industry, it appears that there may be a possibility of its use to advantage for the melting of cathode copper. In the case of copper the problem is not one of actual refining, because the copper if refined properly y the electrolytic method needs no further refining; it needs simply to be cast into a marketable shape. The name" refining". is applied to the present finishing process, because in the operation oxygen and other impurities are removed, which the electrolytic copper absorbs in being melted in the reverberatory furnace. Considering that processes may be positive, negative, and neutral; the electrolytic method would be positive; reverberatory melting of cathode copper, negative; and electric furnace melting, neutral. The electrolytic method produces about as pure a copper as is possible, if operated properly and the anodes are not too impure. The final reverberatory melting of this cathode copper lowers the grade of the final product, due to the absorption of gases and impurities.

Jan 8, 1914

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young&apos;s moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.&apos; In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young&apos;s modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young&apos;s modulus and substantial magnetic permeability.&apos; Young&apos;s modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.&apos; This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.&apos; The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).&apos;. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.&apos; Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young&apos;s modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.&apos;, " In this method Young&apos;s modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101&apos; dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young&apos;s Modulus Values at 25°C: The modulus values of O&apos;, 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952

By Charles Barrett

THE copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possi-bility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previ-ously the structures in this system are unique in their; origin, for one terminal solid solution will precipitate the other, and ice versa. In most of the other systems for which crystallographic data on the precipi-tation (or transformation) process are available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system1 is 779°C. At this temperature copper -dissolves 4.3 atomic per cent (7.0 weight per

Jan 1, 1935

By S. R. Titley

The recent emphasis placed upon the use of molybdenum as a geochemical indicator has stimulated considerable inquiry into the behavior of molybdenum in the zone of oxidation. This paper represents a summary of recent and continuing experimental work and calculations in an investigation of a portion of the system Mo-Fe-S-H20 and treats the stability of various iron and molybdenum compounds with respect to oxidation potential and pH. Using experimentally determined free energy values for ferrimolybdite, diagrams of the stability fields of this mineral have been calculated with respect to ilsemannite (?), molybdenite, pyrite and limonite. This theoretical approach is the one utilized by Garrels3&apos;4 in studies of the relationships of various minerals in the zone of oxidation. Use of this approach is particularly suited to the study of geochemistry in the zone of supergene processes because of the low temperatures, low pressures and other relatively easily determined and duplicated factors that exist in the near surface environment. Such a study of molybdenum, however, is complicated by several factors. One of these is the fact that the strong amphoteric behavior of molybdenum makes possible a wide variety of substances and complexes whose exact chemical natures are unknown. The second factor is the dearth of thermodynamic data for many of the simplest of the possible compounds and ions important to the study. For the purpose of this study, the problem of complexes has been approached through considering only the simpler possibilities realizing that the complexes and systems so treated may be gross oversimplifications. All the complexes considered, however, have been suggested in the chemical 2,7,9,12 or geologi-cal literature. EXPERIMENTAL WORK Studies of the behavior of molybdenum ions and ferrimolybdite have been carried out in aqueous sys- tems, and reactions have been followed by simultaneous measurement and recording of pH and oxidation potential. A major problem involved in this study was the long periods of time necessary for equilibrium to be established in some of the systems considered; in a few instances, these periods exceeded four weeks, that is, four weeks during which measured conditions changed continuously. Another problem, in some instances, was the indeterminate nature of the reactions that have taken place. Because of the tendency of molybdenum to complex, reactions which take place under some of the more extreme imposed conditions of oxidation and acidity or alkalinity are unknown. However, useful data for the present work were obtained from studies of the molybdate ion and ferrimolybdite between pH 2 and 8 and under only moderately oxidizing to nonoxidizing conditions. Instruments used in the experiments were a Hewlitt-Packard Model 412A VTVM, a modified Beckman Zeromatic pH Meter and two Varian model 11 recorders. pH was measured between glass and calomel electrodes and Eh was measured between calomel and platinum electrodes. Conditions of pH were varied with 1N H2SO4 and 1N NH4OH and 1N NaOH. Eh was varied with gaseous nitrogen, oxygen or aqueous H202. Ambient temperature was essentially uniform at 24ºC and was increased in the reaction vessel by the positioning of a magnetic stirrer whose temperature was sufficient to bring the temperature to 2S°C in the reaction. The temperatures of reaction did not vary more than 1/2ºfrom 25°C. Two reactions were investigated, the ferrimolybdite-limonite-water reaction and the reduction of molybdate ion. Studies of both reactions yielded useful data that were used in preparation of the Eh-pH diagrams. The traces of the reactions are shown on Fig. 1. Ferrimolybdite-Limonite- Water: Studies of this reaction involved analysis of the solution of ferrimolybdite and simultaneous formation of ferric hydroxide. The data are summarized on Fig. 1. In this reaction, equilibrium was attained at various pH&apos;s when coexistence of the two solid phases (ferrimolybdite and ferric hydroxide) was attained. At the proper pH, controlled by the amount of ferrimolybdite and thus the dissolved content of molybdate species, both phases were observed and reaction times to complete the transition were on the order of weeks. The reac-

Jan 1, 1963

By R. W. Gurry

WHEN a steel in the austenitic state, with all its carbon in solution, is maintained, at constant temperature, in contact with a gas that removes the carbon from the surface, vet without otherwise altering the composition of the steel, the change in weight of the specimen, after any period of exposure, is a direct measure of the amount of carbon it has then lost. The purpose of the present paper is to show how, by application of established mathematical reasoning based on the fundamental diffusion law and on certain postulates, this loss of weight yields a complete picture of the distribution of carbon throughout a specimen of regular shape after any period of exposure, with all the accuracy required in any practical occurrence of decarburization. Precisely the same is true for the gain in weight during the reverse process of carburization, or for the gradual gain or loss of any element, so long as the steel comprises only a single phase at temperature, provided always that the experimental conditions conform to the postulates. The change in carbon content from surface to center of the specimen is always continuous, when everything is in solution, even though under the microscope the decarburized zone (or carburized rim) may appear to be sharply defined. The experimental procedure is described and some typical results are presented, which are then interpreted by application of the diffusion law. EXPERIMENTAL PROCEDURE Initially an endeavor was made to follow the gain of weight during the process of carburization in a hydrogen-toluene atmosphere, but it was soon found that the specimen became coated with graphite, which could not be removed without some loss of metal; therefore it was decided to continue carburization until the steel was saturated throughout, to remove all graphite from the surface of the specimen, and then to follow the loss of weight during decarburization in a moist hydrogen atmosphere at the same temperature as that used for carburizing. The carburizing procedure has been described in an earlier paper;1 it suffices to state here that the carburization lasted about 140 hr. at 760°C. (1760°F.) and 44 hr. at 1110°C. (2030°F.), these periods being long enough-on the basis of the calculations presented later-to ensure that the specimen was about 9.99 per cent saturated at each temperature. The speci¬men was a cylinder about 3.8 cm. long and 0.475 cm. in diameter; the materials were carbonyl iron, a commercial low-metalloid iron, and a steel with 3.6 per cent nickel and the usual proportion of other elements. The fully [carburized] specimen, after cooling at the top of the furnace tube, was placed in a lathe and sandpapered to remove all graphite; then the diameter was measured with a micrometer caliper, and the initial weighing (corresponding to complete saturation) was made. By means of a

Jan 1, 1942

By Robert Franke

(Butte Meeting, August, 1915.) IN view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the imme diately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years&apos; operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in.

Jan 7, 1913

By W. C. Phalen

INTRODUCTION NOBODY will dispute the fact that the conservation in every legitimate manner of our valuable high-grade phosphate-rock deposits is a present-day problem of importance. The table and curve, given herewith, show. that during the past 10 years the exportation of high-grade rock has averaged very close to half the total output of the entire country. The bulk of this exportation is from Florida, for obvious reasons. It is plain that the deposits in this State, more particularly, are being wastefully depleted under a system of selecting the cream of the product for exportation to Europe, leaving the comparatively low-grade rock, running from 65 to 70 per cent., and under, in bone phosphate of lime, for our own n fertilizer manufacturers to work up when all the best rock is gone. In this paper the writer has endeavored to make a point of describing in some detail the important methods of production and conservation in Tennessee. These ought to prove of educational value to our American agriculturists and fertilizer manufacturers, and should result in a demand for the highest-grade rock, both for direct application to the soil and for use in making acid phosphate. It is certainly evident that the European

Jan 10, 1916

By R. E. Ogilvie, J. I. Goldstein, R. E. Hanneman

The interdiffusion coefficients for the Fe-Ni system were determined as a function of composition in both the a and y phases at 1 atm pressure. The inter diffusion coefficients were also determined in the y phase at 40 kbar pressure. The concentration gradients were measured with an electron probe, and the diffusion coefficients were calculated by the Matano analysis. At 1 atm, Ey increases with nickel content up to 65 at. pct Ni. The relationship of Dy with temperature and nickel concentration, up to 50 at. pct Ni, is given by the equation DY-l atm = exp(.0519 CN~ +1.15) MANY of the transformations that occur in the solid state are diffusion-controlled, especially those involving precipitate growth in most metallurgical systems. Multicomponent diffusion is usually expressed in terms of a chemical or an inter diffusion The activation energy Q at 1 atm decreases from pure iron to 60 to 70 at. pct Ni and decreases from pztre nickel to 60 to 70 at. pct Ni. The Kirkendall marker movement indicates that DFe is greater than DNi zcp to about 60 at. pct Ni. Above 60 at. pct Ni, however, DNi becomes peater than DFe The inter diffusion coefficients were also compared with those calculated from self-diffusion data. A comparison between calculated and measured coefficients shows only rough agreement. The effect of 40 kbar pressure is to decrease DyPl atm by an order of magnitude. The activation volumes for high-pressure diffusion are in favorable agreement with theoretical models developed for self-diffusion. coefficient which determines the rate at which material is transferred from the matrix phase to the precipitate and hence determines the growth rate of the precipitate. Since the numerical values of the diffusion coefficients differ widely as a function of the metallic system, temperature, and pressure, the diffusion coefficients must be determined for each particular environmental condition. Of long-standing interest is the growth of the classic Widmanstatten pattern in metallic (Fe-Ni) meteorites. The growth rate of the pattern is controlled by the diffusion coefficients in the Fe-Ni system. Since these coefficients are essential to calculating the growth rate of the pattern, we found it necessary to determine the diffusion coefficients

Jan 1, 1965

By H. G. Doll

THIS paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole. By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simple and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, timesaving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given.

Jan 1, 1944

By M. A. Mahtab, J. D. Dixon

The results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block- caving method are presented. The two-dimensional finite-element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1977

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By E. B. Swanson

There is only one way to transport natural gas and that is by pipe lines. In the past few years, these lines have been extended rapidly into areas which previously had been served mainly by solid and liquid fuels. In the subject given me, this extension is referred to as an invasion, which implies a rather forceful entry. Whether or not such an implication may be applied to recent natural-gas developments is unimportant. It is the fact of the extension, not its definition, which is important. For centuries, natural gas has been utilized for various purposes in many parts of the world. It was the foundation of fire worship at Baku. The Chinese used it for the evaporation of brine in salt manufacture. In our country, its history seemingly dates back 110 years to the vicinity of Fredonia, N. Y., where seepage gas was assembled and used for lighting purposes. A few years later, a %inch pipe was laid to a lighthouse on Lake Erie, and the early records of the Lighthouse Service tell of the difficulties surrounding this use. With the discovery of oil in Pennsylvania, there followed further development; the town of Titusville was piped with natural gas and, some few years later, gas was made available for manufacturing plants adjacent to the oil fields. For more than a half century, the industry was concentrated in the

Jan 1, 1932

By R. K. Buhr, H. Thresh, M. Bergeron, F. Weinberg

The microsegregation of nickel and chromium in directionally solidified AISI 4340 steel castings has been measured using electron probe microanalysis. Minimum concentrations were observed to occur at the center of the dendrite stalks, as reported previously. However, the position of the maximum concentrations could not be determined from the dendrite configuration. An etching technique has been developed which shows the position of maximum concentration. Measurements were made of the distribution of nickel and chromium in the dendritic structure. The ratio of maximum to minimum concentration was determined as a function of primary dendrite arm spacing for both as-cast and partially homogenized materials. The results are compared with observations reported in the literatuve. A S part of an investigation of solute segregation in directionally solidified AISI 4340 steel casting, electron probe microanalysis was used to measure the distribution of nickel and chromium in the dendritically segregated material. This complemented the observations on the segregation of radioactive phosphorus obtained by autoradiographic techniques in the same castings.&apos; Kattamis and I?lemings2 have reported similar measurements, using electron probe microanalysis, on dendritically segregated AISI 4340 steels. They found minimum solute concentrations occurred at the center of dendrites, maximum concentrations occurred in the center of interdendritic regions, for symmetrically oriented dendrites, and a regular variation of concentration within dendrite arms. The ratio of maximum to minimum concentration was found to be essentially independent of position in the castings, except near the chill surface where it was somewhat higher. Assuming complete diffusion in the liquid and no diffusion in the solid during freezing, they considered that isoconcentration curves in the steel were homothetic. As a result, isoconcentration curves of the various elements, contour surfaces of dendrites produced by isothermal-transformation studies, and the contour of the solid-liquid interface would all be similar, and could be superimposed by a uniform expansion or contraction of the contours. Preliminary results of the present investigation suggested that isoconcentration curves were not homothetic. It was also evident that points of maximum concentration could not be predicted from the dendrite configuration. Since the ratio of maximum to minimum concentration appeared to be an important parameter in defining the overall segregation in a casting, other techniques for determining the point of maximum concentration were investigated. In addition the overall solute distribution associated with the dendritic structure was examined for both nickel and chromium, and the consistency of the distribution for neighboring dendrites was determined. METHOD Fifty-pound heats of AISI 4340 steel were cast in a manner similar to that used by Flemings et al3 with a water-cooled copper base plate and exothermic sides and top. The nominal composition of the material was C, 0.41 pct; Mn, 0.66; Si, 0.35; S, 0.012; P, 0.010; Ni, 1.88; Cr, 0.95; Mo, 0.28. The steel solidified directionally from the chill surface, with a dendritic structure which increased in dendrite arm spacing with increased distance from the chill. Results of the general investigation of the cast structure and segregation of radioactive phosphorus in these castings have been reported elsewhere.&apos; For the present measurements, sections were cut from the casting at several distances from the chill surface. The sections were subsequently heat-treated, mounted, and then polished on a plane perpendicular to the general freezing direction of the casting. Electron probe microanalysis was carried out with the JEOL-JXA3 microprobe using a voltage of 25 kev and beam current of 0.15 µa. The take-off angle is 22 deg. Quartz crystals were used in the spectrometers and measurements made for Ka radiation from both nickel and chromium simultaneously. A thin layer of carbon was deposited on all specimen surfaces prior to examination in the microprobe. Early measurements were made on polished surfaces, with indentation marks produced by a hardness tester to indicate the area of interest. It was found desirable to use etched surfaces, as opposed to polished surfaces, to reduce sample preparation time and more readily relate the microprobe scan to the structure. To determine if this could be done, without introducing significant errors, a series of measurements were made on polished and etched surfaces of the same specimen. Both polished and etched surfaces produced similar results within normal scatter as shown in the observations. Subsequent measurements were then made on etched surfaces. Measurements with the microprobe analyzer were made by point counting, for periods of 100 sec, at 10-µ intervals. Ten-second counts were made on pure nickel and chromium standards, incorporated in the specimen mount before and after each set of measurements. The results were adjusted for background, then corrected for dead time using the expression:

Jan 1, 1969