Search Documents

At the meeting of the Board of Directors of the Institute on Jan. 26, 1917, the following actions were taken: Messrs. A. C. Clark, Lawrence Addicks and G. D. Van Arsdale were appointed Tellers to count ballots for Officers and Directors. Messrs. T. T. Read, V. S. Harper, and. E. J. Hall were appointed Tellers to count ballots on revised spelling. The Finance Committee's audit for the year 1916 was approved and ordered filed. The Report of the Finance Committee upon the method of raising this Institute's share of the deficit on the additions to the building was approved and accepted. Upon the recommendation of the Secretary, increases in the salaries of some of the employees were approved. The St. Louis Section received an appropriation of $200 for the year 1917. The Columbia Section received an appropriation of $150 for the year 1917. The Montana Section received an appropriation of $100 for the year 1917. The Colorado Section received an appropriation of $175 for the year 1917. The Utah Section received an appropriation of $125 for the year 1917. The Puget Sound Section received a set of Transactions in standard binding. The International Engineering Congress received a loan of $300 until the Congress can realize upon some of its assets.

Jan 3, 1917

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an' 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By W. J. Kroll

Jan 1, 1960

By S. S. PRENZ

Discussion held at the sessions of the Canal Zone meeting, November, 1910. [SECRETARY'S NOTE.-As a result of this discussion, an expression of opinion covering all points of unanimous agreement was adopted and signed by members of the Institute party as individuals. This statement, which was printed in the Bulletin of December, 1910, is reprinted below, as an introduction to ,the detailed report of the discussion. It should be clearly understood that it does not constitute an official declaration by the Institute, the rules of which forbid any such action. At the New Haven meeting of February, 1909, a free discussion of the plan of the canal took place, in which the critics of the present scheme had full opportunity to state their views. That discussion was continued at considerable length in the newspapers ; but the Institute was never committed to either side. In this latter instance, the situation is precisely similar. Certain members and guests of the Institute, having had the advantage of later developments and of personal inspection, have expressed the conclusions at which they have arrived on their own responsibility ; and these conclusions are published by the Institute, subject to further discussion, like any other part of its proceedings. The general statement referred to contained a promise that the full discussion, of which it was a result, would be subsequently printed ; and this promise is fulfilled, so far as practicable, in the subjoined report, concerning which I beg to offer the following explanations: 1. It is made up of the remarks of the members of our party, as subsequently written out and mailed to the Secretary. 2. In editing these contributions, I have condensed the material considerably by cutting out much repetition of opinions and phrases ; and in such excision, I, frankly confess, the authors whose communications were delayed, have been the sufferers. Nevertheless, there is a good deal of repetition left, as there must be, when so many persons had talked so much, and come to agreement upon so many points. 3. It has been found impossible to preserve in this report the actual order of the free and informal oral discussion represented. Consequently the several contributions have been arranged in alphabetical order under the names of their authors. References to "preceding speakers," etc., must therefore be construed as referring to other speakers, preceding or following.-R. W. R.] S. S. PRINZ AUGUST WILHELM, AT SEA, November 14, 1910. We, the undersigned, members and guests of the American Institute of Mining Engineers, after a visit to the Isthmus of Panama, and inspection of the work of the United States Isthmian Canal Commission, and after full discussion of our individual impressions, find ourselves in unanimous agreement as to the following conclusions:

Jan 1, 1911

By K. J. Gill, P. Chiotti

Thermal, metallographic, and vapor pressure data were obtained to establish the phase diagram for the thorium-zinc system. Four compounds corresponding to the stoichiometric formulas Th2Zn, ThZn2, ThZn4, and Th2Zn17 were observed. The melting points of these compounds under constrained vapor conditions were found to be 1055°, 1105°, 1095°, and 1015°C respectively. Four eutectics exist in this system with the following eutectic temperatures and thorium contents in wt pct: 1040°C, 89 Th; 945°C, 79 Th; 1045°C, 55 Th; and 995°C, 35 Th. The standard free energy, enthalpy, and entropy of formation for the compounds were determined from zinc vapor pressure data. ALTHOUGH the thorium-zinc system has been of technical importance in the commercial production of thorium and more recently of interest to some proposed pyrometallurgical separations processes for reactor fuels or blanket materials no detailed investigation of this system has been made in the past. Some previous work has been reviewed by Hanssen.1 The existence of four compounds, Th2Zn17, ThZn4, ThZn2, and Th2Zn has been established and their crystal structures have been studied by X-ray diffraction techniques.2-4 Smirnov et al.,5 determined the solubility of thorium in zinc and investigated the two-phase region between Th2Zn17 and zinc. They calculated some of the thermodynamic properties for these alloys from emf measurements on the cells Th/ThCl4(fused)/Cl2, C and Th2Zn17(s)+ Zn (l)/ThCl4(fused)/Cl2, C. The possibility of reaction between the anode materials and fused thorium tetrachloride to produce a lower valent thorium salt would have to be resolved in order to evaluate the results obtained. The purpose of the present investigation is to establish the phase diagram for the thorium-zinc system and to determine the standard free energy, enthalpy, and entropy of formation for the compounds formed. MATERIALS AND EXPERIMENTAL PROCEDURES The metals employed in the preparation of alloys were Bunker Hill slab zinc, 99.99 pct pure and Ames Lalboratory thorium. The major impurities in the thorium in parts per million were oxygen—1250, carbon—350, iron—100, nitrogen-75, and silicon—70. The metals in the form of several small massive pieces, total weight about 30 g, were cleaned with acid, washed with water and acetone, and dried just prior to their use for alloy preparation. Tantalum containers were found to be suitable for all the alloys studied and were used throughout this investigation. The metals were sealed inside of small 1-in.-diam tantalum crucibles by welding on preformed tantalum covers. A small thermocouple well made from 1/8-in.-diam tantalum tubing was welded in the bottom of each crucible. These crucibles were enclosed in

Jan 1, 1962

By C. E. Sims

THE following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admit¬tedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold are outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided.

Jan 1, 1932

By Ogden Malin

IN conducting the manufacture of extruded brass rods and brass forgings it has been noticed that there is considerable variation in the physical properties, particularly the machinability of different rods and forgings, even though the composition, working temperatures and method of manufacture remain the same. It is the purpose of this paper to attempt to establish the cause and extent of this variation, and also to determine whether variations in composition within certain defined limits influence hardness and machinability to any marked degree. The writer believes that this variation probably is due to the variation in grain size of the metal, therefore the microstructure of several compositions under various conditions of working were examined in an effort to establish this as a fact.

Jan 1, 1932

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By L. F. Stutzman, George Thodos

A new graphical method, which is a modification of that proposed by Buckley and Leverett', is presented for the determination of the displacing fluid saturation at breakthrough for frontal drive mechanisms. This method is applicable to all types of fluids, which may be either soluble or insoluble in the oil at reservoir and injection conditions. This adaptation has unique advantages in handling problems in which either liquids or gases are the displacing fluids. INTRODUCTION In the displacement of oil from a reservoir with water or gas injected into the formation or by the expansion of a gas cap, the determination of breakthrough or flood advance is important to define the initial and subordinate phases of the operation. Thus, the determination of the displacing fluid saturation at breakthrough is fundamental to the establishment of over-all reservoir production. Methods for analyzing this saturation and for calculating production rates have been previously reported1,'*".". All of these methods utilize the rate equation for linear flow developed by Buckley and Leverett1. xs = QT - Qn/A? (?fu/?Su) .....(1) Sp where f, represents the volumetric fraction of displacing fluid in the total flowing fluid within the reservoir as is defined by: fo = 1/1+ ku/kd µn/µn .......(2) Since the time, ?, necessary for the flood front to travel distance ?X is unknown, Eq. 1 cannot be solved directly for the determination of the breakthrough point. Therefore, it becomes necessary to solve Eq. 1 simultaneously with an equation representing a fluid bal-ance on the reservoir behind the flood front. To develop such a fluid balance equation, it has been assumed that the fluid composition is uniform in the reservoir behind the flood front. Based upon this assumption, the follow-ing equation can be derived from a material balance on the displacing fluid: x = (?X) s Dx ? x=0 [ Snx - Sn1 ] dx = QT - Qn/A? It is readily observed that the displacing fluid satura-tion behind the flood front, Snx, may be determined through the simultaneous application of Eqs. 1 and 3. Although the approach may vary, this objective re-mains the same for all of the previously mentioned graphical or analytical methods. After Sox is determined, it is then possible to calculate the gas-oil and/or water-oil ratios and the rates during the initial and subordinate phases of production, and thereby define the production history of the reservoir. In this presentation only the de-termination of Snx is considered, and the reader is re-ferred to the several texts in reservoir engineering2,4,5 for a complete discussion on the methods for establish-ing the production history of a reservoir. PROPOSED METHOD FOR DETERMINING Snx Since at any time the quantity, QT - Qn/A? is a constant, Eq. 1 may be expressed in differential form as follows: dxsn = QT - Qn/A? d (? fn/? Sn) sn .....(4) Eq. 4 may be substituted directly into Eq. 3 to obtain: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = QT - Qn/A? ...............(5) Eq. 5 simplifies to the expression: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = 1 ....(6)

Jan 1, 1958

By Fulton Flick

THE micrography and macrography of aluminum and its alloys present certain difficulties. Many of the difficulties attendant on the micrography have been removed by methods developed during the past few years, notably those of E. H. Dix, Jr.1 The development of grain size in aluminum and its alloys may be equally troublesome, yet comparatively little detailed attention appears to have been given to it. Satisfactory reagents. are available for the development of such structures in ferrous and most non-ferrous metals, but those applied to aluminum and its alloys, i. e., alcoholic or aqueous solutions of sodium hydroxide or hydrofluoric acid are not entirely satisfactory. Hanson and Archbutt,2 in speaking of these two reagents, state that "These two reagents give fairly satisfactory results, but they sometimes produce badly tarnished surfaces from which the surface deposit is difficult to remove." It has been our experience that neither of these reagents is to be entirely relied on for developing structures suitable for study or photography. This means that when the etch fails to produce satisfactory results the, specimen must be repolished, through the 000-paper at least, and then etched with another reagent. This procedure entails a con¬siderable loss of time, and the final results may not be all that might be desired. However, the reagent to be described, although not a panacea for all etching troubles, has improved results so markedly that it is felt that it is worth offering as a grain-size etch generally applicable to aluminum and aluminum alloys. Czochralski3 in 1915 mentioned the application of a solution of 10 to 20 c. c. concentrated hydrofluoric acid in 100 c.c. absolute alcohol, etching in this reagent being followed by dipping in concentrated hydrochloric-acid solution.

Jan 2, 1925

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930

By Gorr W. W., Wyche E. H, R. Smith

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Gorr W. W., R. Smith, Wyche E. H

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957

By A. A. Steel

(Spokane Meeting, September, 1909.) DURING. the summer of 1905 I was employed by the U. S. Geological Survey to investigate the geology, Mining, and preparation of barite in most. of the fields of the United States. The Eastern districts have been more or less completely described ; the Virginia field in detail by Thomas L. Watson, in his paper, Geology of the Virginia Barite-Deposits,&apos; and other fields in abstract., including statistics of production and references to current literature, by various authors .2 There have also been published a few details of the occurrence of barite in the lead-mines of Washington county, Mo.3 The other accounts of this district are erroneous and meager, and since this field is the most important one in the United States at the present time, a detailed description of the local geology seems doubly desirable. Barite-deposits are scattered over nearly the whole of Washington and adjoining counties, but. the product, is all mined from the areas indicated upon the sketch-map, Fig. 1, and is shipped from the stations of the St. Louis, Iron Mountain &. Southern railway, between Blackwell and Potosi, from 45 to 60 miles SW. of St.. Louis. The topography is for the most part gently rolling, with slightly graded streams, usually less than 200 ft. below the higher hill-tops. Along Mineral fork and Indian creek are :some steep bluffs and cliffs, affording good exposures of the

Feb 1, 1910

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years&apos; experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8&apos;9&apos;11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth&apos;s magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

[ ]

Jan 1, 1942

By Enrique Hauser

Discussion of the paper of ENRIQUE HAUSER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 521 to 534. GEORGE A. BURRELL, Pittsburgh, Pa. Mr. Hauser determined the influence of inert gases on the properties of fire-damp mixtures, and one might take some issue with his work on the effect of hydrogen, on those mixtures. It is valuable information to have, but as far as the practical application of it goes, it is not of much significance, because one does not find it in mines, at least not in any appreciable amount. The same Fig. 1.-APPARATUS FUR DETECTING COMBUSTIBLE GASES IN AIR. thing can be said of ethylene. Ethylene is formed in considerable quantities as a product of heat reaction, but normally, in the coal mines, as a result of a great many analyses we have made at the Bureau of Mines, we cannot say that ethylene is a combustible gas found in the fire-damp in coal mines.

Jan 5, 1916

By P. Sanchez-Mejorada

GEOLOGISTS who are acquainted with the mines of northeastern Mexico realize that the most important lead-silver replacement deposits of the province are confined to a single formation. But since the formation is several hundred meters thick, the author has determined the relative position of the lead mantos in the belief that this information will prove useful in the search for new mines. This article describes the stratigraphic location of lead-silver replacement deposits known in several mines situated in a region comprising part of the states of Coahuila and Nuevo Leon. The area studied extends for 200 km* (125 miles) from east to west and 70 km (45 miles) north to south. Metallogenic Province: The most important metallic deposits of the region have the following common characteristics: 1) The orebodies occur as manto replacements of calcareous sediments. 2) The horizons that have contributed large tonnages of ore are in similar positions in the corresponding stratigraphic columns (as it will be shown later on). 3) Lead is the most important metal in the ores. Silver is commonly present in small amounts. Occurrence of zinc is dependent on the degree of oxidation of the primary sulfides. 4) A large proportion of the total production has been in the form of oxidized ores. 5) The deposits are located on anticlines. Rocks of Cretaceous age crop out over large areas of the states of Nuevo Leon and Coahuila. forming part of a belt that extends to the south along the eastern Sierra Madre. The sediments are cut by a small number of intrusive stocks ranging in characteristics from rhyolite to diorite. The most prominent structural feature of the region is a series of folds trending northwest-southeast. Faulting is not conspicuous in the region, although a major fault zone is found farther East.&apos; The physiography closely reflects structural features, with mountains formed by anticlines and valleys conforming with intermediate synclines. Narrow valleys have also been developed along the axes of many anticlines, where solution of limy sedi- ments and erosion have proceeded along axial tension fractures. Stratigraphy: Rocks of the Upper Cretaceous are exposed in only a small percentage of the total area. Generally they have been eroded away from the mountains and are covered by recent talus and alluvium in the valleys. Humphrey&apos; has published an excellent paper describing the Cretaceous formations of the Sierra de los Muertos, a short distance west of Monterrey. A brief summary of these formations is given below to convey an overall picture of the stratigraphic sequence that prevails just south of the area under consideration. Upper Cretaceous Indidura: Essentially thin shaly sediments. Cuesta del Cura: Limestone in thin wavy beds

Jan 1, 1959