Search Documents

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By Arthur Smith

THE Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district-the United Verde and the United Verde Extension-lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., . a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to? the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Wood chute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the . smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. This strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the vicinity of Allen Springs, at the south end of Mingus mountain and all within the boundaries of the Prescott national forest reserve.

Jan 3, 1924

By Edward B. Durham

The refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying Illore than 200 parts of precious metals in 1,000, or, in mint parlance, over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum gronp that were in the bullion. This residue is relatively small, and is melted into bars and stored until suEcient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's osce, laboratory, and , re- spectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Jan 1, 1912

By B. S. Butler

Introduction. THE New London copper mine, about 81, miles east of Frederick, Md., was visited by the Writers for a few hours in the spring of 1909 and the following brief notes on ore specimens collected are presented as a contribution to studies in chalcocite ores. For certain data on the structural and areal geology of this portion of Maryland the writers are under obligation to the unpublished notes and maps of Arthur Keith. The detailed study of the ores is the work of B. S. Butler. The deposit here discussed has many similarities to those of the Virginia district of Virginia and North Carolina, which have been described y Graton1 and Laney2, except that in the deposits of the New London mine chalcocite is by far the most important ore mineral, while in the Virginia deposits bornite is commonly-the most important sulphide. In the New London occurrence calcite is the most important gangue mineral.

Jan 7, 1914

By C. M. Schwartz, A. E. Austin, W. B. Wilson

High-temperature X-ray diffraction studies were conducted with Th-U alloys with up to 10 wt pet U. The solid solubility of uranium in thorium as a function of temperature was determined by the method of lattice parameters. Thorium will dissolve up to 2.5 wt pet U at 950°, 4.5 wt pet U at 1150°, and 7.5 wt pet U at 1250°C. Determinations were made of the temperature of the transition of thorium and of the effect of uranium upon the transition. The a to ß transition for thorium was observed to occur at 1330' ±20°C. Mean coefficients of expansion were calculated for thorium and two alloys, and for ThO2 in contact with the thorium, using X-ray lattice-parameter data. Values obtained at 950° C for thorium and Tho2 were 12.1 and 9.40 X 10-6 per OC, respectively. Impurities obtained during the X-ray exposure were identified by diffraction and were essentially Tho2 and ThC, with two additional unknown phases being detected. The effect of the impurities upon the results is discussed. DIRECT investigation (i.e., high-temperature X-ray diffraction studies) of the phase diagram of thorium-rich uranium alloys has been shown to be necessary since recent work1 - has disclosed the presence of an allotropic transformation near 1400°C in pure thorium with the room temperature face-centered-cubic phase transforming to a body-cen-tered-cubic structure at the elevated temperature. The effect upon the transition of the addition of uranium to thorium and of the solubility of uranium in thorium at high temperatures remained unknown, yet was of interest in understanding fabrication procedures and elevated temperature use. The present work was undertaken to provide information in this area by determining the transition temperature, the effect of uranium on the transition temperature, and the solubility of uranium in thorium as a function of temperature. Experimental Work The high-temperature diffraction data were obtained using a camera especially designed for the purpose3 and capable of reaching temperatures in excess of 2000°C at pressures as low as 1 x 10." mm Hg. Temperature regulation was provided by regulating the power input to ±0.1 pet variation, and by regulating the water flow through the camera jacket to provide a constant thermal load. The X-ray sample was a rod nominally 80 mil diam, which was further turned down to 20 mil and then etched to 18 mil over 1/2 in. of one end. This was placed in the sample holder and mounted on the camera so that the smaller part was surrounded by a cylindrical tantalum-sheet radiation-type heating element. Diffraction from the sample was recorded on film after passing through a slot in the heating element and radiation-baffle shield and through beryllium vacuum windows. The X-ray film mounting was of the Straumanis type4 with a camera diameter of 114.59 mm. Since previous work of Chiotti' indicated that impurities considerably alter the transition temperature, chemical analysis of the arc melted iodide crystal-bar thorium samples was obtained prior to testing. The analysis disclosed the material to contain as low as 0.001 ±0,0002 wt pet H and 0.007 ±0.001 wt pet 0. Carbon was 0.003 wt pet and nitrogen less than 0.002 wt pet. This material was sealed in mild steel in an inert atmosphere and subsequently hot rolled to 3/8-in. diam rods at a temperature of 732°C. Following removal of the jacket, the material was pickled and cold swaged to 1/8-in. rods, from which the diffraction samples were prepared. The alloys were similarly prepared, with the uranium being added during arc melting. The uranium analyses of the alloys prepared appear in Table I. The experimental procedure for diffraction examination of the three samples of high-purity thorium differed from those of the Th-U alloys. The original practice, later modified, consisted of pumping down the camera with the diffusion pump on and then admitting liquid nitrogen to the cold trap of the system. This was modified for the Th-U alloys by maintaining liquid nitrogen in the cold trap at all times before and while the diffusion pump was heated. This minor change produced a reduction in the amount of carbon pickup by the sample during exposure to the diffusion-pump vapors. The sample was brought to the desired test temperature and exposed for 21/2 hr at pressures which were usually 2 x 10-6 mm Hg, or lower. Exposures were made at

Jan 1, 1959

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

By D. J. Carney, C. W. Boquist, E. C. Rudolphy

Effect of variations in sinter feed composition on sinter strength, bulk density, re-ducibility, chemical composition, and microstructure were determined by sintering experimental samples on a production sintering machine. Increasing amounts of roll scale, ore fines, return fines, and blast furnace slag were most beneficial to feed permeability, sinter bulk density, and strength. Burnt lime additions improved feed permeability but were not beneficial to sinter strength or bulk density. Sinter reducibility was adversely affected by all additives. DEVELOPMENT of methods for evaluating sinter quality, which would in some way predict the behavior of the sinter during charging and smelting in the blast furnace, has been given considerable attention in recent years. In a previous investigation at South Works of the United States Steel Corp., standard sinter sampling and testing procedures were developed.1,2 By modifying the sinter sampling device, a method of sintering experimental mix sinter samples upon a production Dwight-Lloyd sintering machine was also developed. This technique afforded a rapid and controlled method of investigating the effects of the various raw materials and additives on sinter quality and was used in this present investigation. Since the beginning of the present study in 1953, the results of numerous sinter investigations have been published, most of which were concerned with production tests of iron ore sinter, both here and abroad. Three groups of investigators reported results of experimental sinter studies that were related to this investigation. Voice et al.3 studied the effects of controlled variables on sinter quality by producing and testing experimental Northants iron ore sinter using an experimental sintering unit. Mor-rissey and Powers&apos; determined the relationship between iron ore sinter quality and the moisture and coke content using a small laboratory sintering system. Burlingame et al.5 studied the effects of "additives" upon iron ore sinter using a laboratory sintering apparatus and laboratory grade raw materials. At South Works, it was considered desirable to study the effects of sinter mix composition and additives upon the quality of a flue dust-base sinter produced on a production sintering unit. Extrapolation of controlled laboratory test data to sintering plant operation lacking such precise control is not altogether satisfactory. Therefore, the present study was conducted in a manner which approximated production conditions as closely as possible. The raw materials used were those commonly encoun- tered in the production of flue dust and flue dust ore-type sinters and these were varied within extremes encountered in this type of sinter production. Experimental Procedure The experimental sinters were produced from 100 lb mixtures of sinter feed. The principal raw materials and additives used, their particle size, and approximate chemical composition are listed in Table I. The mixing of the raw materials was accomplished by means of a miniature single shaft pug mill shown in Fig, 1. The use of the pug mill as a mixer was decidea upon after encountering difficulty in reproducing the mixing and chopping effect of the sinter plant pug mill with other types of available small mixers. The miniature pug mill was constructed, consisting of 31/2x2x1/4 in, blades spaced 3 in. apart along a 3 ft shaft. Preliminary tests were run with this small mixer to establish the proper rotation speed and the required number of passes through the pug mill to thoroughly mix and distribute all the raw materials in a manner approximating the production Pug mill- Although the effects of varying the mosture content were determined in one particular series of tests, the amount of moisture added was changed as the composition of the experimental mix was varied. The aim in making water additions was to achieve a permeability as high as possible for each particular

Jan 1, 1956

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.&apos; Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.&apos; Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.&apos; Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.&apos; In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.&apos; It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,&apos; or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

By Harry E. Cross

Kiln Products commissioned a Waelz kiln 4 metres in diameter by 75 metres long, in South West Africa in March, 1969, to recover nine in a form suitable for the production of electrolytic zinc. The raw material consists of a mixture of zinc silicate concentrates and zinc rich tailings purchased from an adjacent zinc mine - the mixture containing 20% to 25% zinc. The chemical composition of the ore is tabulated and the initial test results are described. Due to the comparatively low temperature at which the ore starts softening the kiln has certain unusual features to enable the temperature to be controlled within the necessary limits. A detailed description of the kiln, the starting-up problems and present operating conditions and results are presented.

Jan 1, 1970

By C. S. Yust, Lida K. Barrett

The change in shape of the void in a sirzterir~g copper mass has been investigated as a juntction of&apos; density. A serial sectioning&apos; technique was used to eoaltrate the irregular shape of the void at two levels qf density. A measure of the void size and configuration, the proximity number, is defined and used to describe the progress of void removal. The process of. void removal deduced front the observations of this study contrasts with current sintering models in that it takes into account the irregularity of structure of a sintering mass and demonstrates that isolated Porosity does not occur first as spherical pores, but as large, definitely nonspherical sections of the void void volume. The process of sintering, about which there is much practical and theoretical knowledge, has evaded a direct and thorough analysis despite the intensity with which it has been studied for 60 years or so. This is due, of course, to the complex structure of a sintering mass and the inability to observe directly the development of a fully dense solid from the initial particulate arrangement. Extensive theoretical analyses have been based on the adoption of one or another of several model systems, that is, by visualization and analysis of some sort of regular assembly or arrangement of geometric "particles" approximating the conditions of a sintering mass. It seems appropriate at this time to try to examine experimentally in some detail the extent to which a sintering mass of irregular particles dlffers from these models. Many models deal with neck growth and the initial stage of sintering and follow the direction established by ~ucz~nski&apos; in 1949 for the sintering of spheres to flat plates. Recently Johnson and cutler2 have adapted these models to sintering of powder masses. coble3 has presented a mathematical model for sintering that applies to the middle and final stages of the process. These papers, without exception, assume a regular geometry, generally spheres in contact in a regular array. Rhines~ and coworkers, however, are studying the sintering process by applying a model based on the topological concept of genus which permits them to consider an irregular structure. whites has described the various models with the exception of that of Rhines et al., and the assumptions on which they are based and their shortcomings. The present paper examines the geometric changes that occur in the powder mass during sintering by examination of the void. The method is to analyze a series of partially sintered structures and to propose from this analysis the sequence of events which occur in the removal of the void space as a sintering mass progresses from a collection of individual particles to a solid body. The irregular nature of the stacking of particles and of the particles themselves will be taken into account. The significant points derived from this study are: first, accurate reconstructions of the irregular void shapes are presented; second, it is clearly established that closed porosity occurs first as widespread volumes of interconnected porosity, definitely nonspherical in shape; and third, a new factor, the proximity number, is defined, which serves in this paper as a tool for describing the void shape changes observed, and which will be used in a later paper as part of the basis of a mathematical model for sintering. While the specific material studied is copper, the observations are thought to be relatively general as indicated by comparison of the results with partially sintered structures in other materials presented in the literature, both metallic and nonmetallic. EXPERIMENTAL PROCEDURE Four series of specimens representing progressive stages of the sintering process were prepared by sintering high-purity copper powder for various time periods. A relatively large particle size was used so that the void-solid interface could be readily distinguished at low magnification. In three series of specimens a loose stacking of particles was obtained by pouring powder into an alumina mold and lightly tapping the mold. The green density of such compacts was approximately 40 pct of theoretical density. Two of these three series utilized irregularly shaped particles in the size range -230 +325 mesh, one series sintered in vacuum and one in hydrogen at 950°C. The third series of loosely stacked particles consisted of spherical particles in the size range -270 +325 mesh, sintered in hydrogen at 950°C. A fourth series was prepared from compacted irregular particles sintered in hydrogen at 950°C. The specimens for this series were formed by lightly pressing the irregularly shaped particles in a steel die; the green density of the pressed pellets was approximately 60 pct. The irregularly shaped particles used in this study are shown in Fig. 1. The density of these particles, measured by a toluene picnometer technique, is 98.2 pct of theoretical density. Each particle is highly convoluted, and in some instances appears in cross section to contain internal porosity. The density measurement, however, indicates that completely enclosed porosity is very small so that the individual particles have a highly irregular surface but are essentially fully dense copper. Therefore, most of the void space that appears in two dimensions to be isolated within the particle is actually at the particle surface and connected to the external void in the dimension not included in the plane of the cross section. The void space that appears as void surrounded by the par -ticle or within folds in the particle w~ll be r~fc\r?

Jan 1, 1968

By Shiou-Chuan Sun

THE fact that coals of different ranks and even of the same rank differ greatly in their amenability to iroth flotation is well known. In recognition of the need for an explanation of this phenomenon, two hypotheses have been suggested. Wilkinsl reported that the floatability of coals increased with an increase of the carbon content or rank. This postulate is handicapped by the fact that bituminous coals that possess moderate carbon contents are actually more floatable than anthracite coals that have high carbon contents, as shown in columns 6 and 9 of Table I. Taggart and his associates&apos; implied that the difference of floatability between bituminous and anthracite coal was caused by the variation of carbon-hydrogen ratio. This is not applicable to the relative floatability of other coals and carbons. For example, column 11 of Table I shows that the carbon-hydrogen ratios of low-floating lignitic coal and non-floating animal charcoal are not only smaller than the moderate-floating anthracite coal, but are also similar to the high-floating bituminous coal. Furthermore, according to this hypothesis, high temperature coke-A (464), Ceylon graphite (1238), and lamp-black (357), all possessing extremely high carbon-hydrogen ratios, should be less floatable than other substances having much lower carbon-hydrogen ratios such as high volatile-B bituminous coal (11.9 to 22), anthracite coal (35.7 to 60.5), lignitic coal (15.6 to 33.6), and charcoal (13 to 26.2). However the former group is actually more floatable than the latter group. In this paper, a surface components hypothesis is Proposed to explain the different floatabilities of coals, carbons, and hydrocarbon minerals. The validity of the hypothesis is experimentally supported by the actual floatability, natural floatability, wettability, and adsorbability for neutral oils of coals, carbons, and hydrocarbon minerals tested. The combustible recovery of the flotation results, as used in this paper. was calculated from Eq. 1: P (100-Ep) 100 RWCP Rc= [1] F (100-E,) C, where R, is the percent combustible recovery; F and P are, respectively, the weight of feed and the weight of concentrate or product; E, and Ep are, respectively, the total percent of ash plus moisture in feed and in concentrate; Ru. is the percent weight recovery: and C, and C, are, respectively, the percent of combustible in feed and in concentrate. Except for ash and moisture content, all chemical components of a coal are assumed combustible. The experimental work included studies on flotation, ultimate and proximate analyses, contact angle tests, extractions of bitumen-A with benzene, adsorptions for liquid hydrocarbons, and wetting tests. Most of the flotation experiments were performed in a laboratory Fagergren machine; others were tested in a small Denver machine. The solid feed for the former was 300 g and for the latter was 30 g. The solid materials used for flotation were crushed to —48 mesh. After the mineral pulp in the flotation cell was agitated for 6 min and the pH was adjusted to 7.5 & 0.2 with sodium hydroxide or hydrochloric acid, a petroleum light oil having a viscosity of 5.73 centipoises at 77 °F was added and conditioned for 2 min. Finally, pine oil was introduced and the froth was collected for exactly 3 min. The weight ratio of petroleum light oil to pine oil was kept constant at 1.5 to 1. Tap water was used for all flotation tests. Contact angles were measured with a captive bubble machine. For each coal sample, three specimens were mounted in transoptic mounts and polished with levigated alumina, first on a sheet glass, then on a cloth-covered metal polishing wheel. The polished specimen was first washed with distilled water and wiped thoroughly on a cleaned linen pad, then transferred into the pyrex cell of the captive bubble machine and conditioned for 6 min., and finally measured for contact angles at three or more points. Except where otherwise stated, the induction time for each measurement was 1 min. The contact angle representing each material was obtained by averaging the measurements of three specimens. The linen pad was first washed with warm distilled water, then boiled 30 min in a 2N sodium hydroxide solution, and finally washed with distilled water until no trace of sodium hydroxide could be detected in the decanted solution. The cleaned linen pad was stored under distilled water. Immediately before using, the pad was rewashed and transferred into a clean pyrex petri dish partly filled with distilled water. The glassware and rubber gloves used were cleaned by soaking in sulphuric acid-potassium dichromate cleaning solution, followed by rinsing with distilled water. The polished specimens were handled only by glass forceps. The ultimate and proximate analyses were made in accordance with the ASTM standard procedures for coal and coke. The extractable bitumen-A was determined by weighing 1 g of —100 mesh sample and placing it in a desiccated and weighed ASTM aluminum-extraction thimble. The thimble was placed in condenser hooks and inserted into an extraction flask containing 100 cu cm of benzene. The flask was heated and the benzene vapor was condensed by water coils. At the end of 24 hr of percolation, the thimble was removed, desiccated, and weighed. Loss in weight of sample was taken as bitumen-A and calculated to dry and ash-free basis.

Jan 1, 1955

By William E. Ford, Edward Salisbury Dana

Normal phosphoric acid is H3P04, and consequently normal phosphates have the formulas R3PO4, R3(P04)2 and RPO4, and similarly for the arsenates, etc. Only a comparatively small number of species conform to this simple formula. Most species contain more than one metallic element, and in the prominent Apatite Group the radical (CaF), (CaCI) or (PbCI) enters; in in the Wagnerite Group we have similarly (RF) or (ROH).

Jan 1, 1922

By W. F. Durfee

In the year 1862 the author of this paper was called upon to design and superintend the erection and working of the machinery of an experimental works for the production of steel by a process

Jan 1, 1884

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals&apos; has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals&apos; has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By H. A. Lesser, H. L. Stone, G. H. Bruce

ESSO PRODUCTION RESEARCH CO., HOUSTON, TEX. A mathematical model that represents the conduction heating of a rock formation of limited permeability is formulated. Heat is introduced by the injection of a hot condensing gas into horizontal fractures through the formation. The fractures are assumed to be equally spaced; the flow of fluid is linear. The model consists of three coupled partial differential equations and two functional relationships. Temperature histories for both fractures and formation are obtained by numerical procedures. Application of the model in predicting in situ heating of oil shale is illustrated with four sample cases. Influences of shale thermal diffusivity, fluid pressure in the fracture and fracture spacing upon heating rate are demonstrated. In all cases considered, several years were required to heat all the formation to 700F with 1,000F steam. Less than 32 per cent of the injected heat was utilized for heating the shale. To facilitate extensive calculations of this type, a set of seven dimension-less quantities are derived. With this dimensionless system, the effect of controllable parameters on economics can be explored. INTRODUCTION Vast deposits of hydrocarbons are contained in oil shale formations in the western United States and in other countries. These hydrocarbons, known as kerogen, are difficult to recover because they are immobile solids and because the rock formations in which they are found have very limited permeability. The kerogen can be converted through pyrolysis to recoverable liquids and gases if the formation temperature is elevated to the range 600 to 800F. To accomplish this heating, the formation might be artificially fractured and a hot fluid injected into the fractures. If the injection and production wells are vertical and the fractures horizontal, interwell communication will be established and the hot fluid will flow from an injection well to a production well. In this process, some of the heat in the fluid will be given up and conducted into the formation. Products of pyrolysis will flow from the heated rock matrix into the fractures and be produced, commingled with the injected fluid. The practicality of such a process is strongly influenced by the rate at which heat can be transferred from the hot fluids to the formation. An analysis of this heat conduction problem is the subject of this paper. Linear flow of a condensing gas through a set of horizontal, equally spaced fractures is considered. Temperature histories for both fractures and formation are obtained from numerical procedures. The analysis also applies to formations containing streaks of natural permeability instead of fractures. Heat flow problems similar to the one treated here have been studied by other workers. Thomas1 has solved a radial problem in which he considers the injection of a noncondensing gas into a single, horizontal fracture and approximates the temperature profile in the fracture by a step function. The solutions to other problems, which are less similar to the present problem than the one treated by Thomas, have been reviewed by Spillette.2 In addition to these mathematical studies, a field test of an in situ shale oil recovery process using hot natural gas as the injected fluid has been reported.3 The first part of this paper is concerned with the mathematical development of the problem. The differential equations, boundary conditions and functional relationships which describe the physical model are formulated and the equations are cast into finite difference form. The method of solution of the difference equations is discussed (Appendix B). The second part of this paper presents results computed for a typical oil shale formation for which steam at 1,000F is the injected fluid. Fracture spacing, horizontal and vertical thermal diffusivities

Jan 1, 1967

By Albert Smith

THE creep properties of metals have as-sumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Insti-tute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influ-ence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investi-gate creep phenomena because of the sim-plicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals.

Jan 1, 1940

By Allan T. Gwathmey, J. Bruce Wagner, Kenneth R. Lawless

Between 250°and 550°C in oxygen pressures of 10 to 760 mm Hg, the relative oxide thicknesses formed per unit time on the (100), (111), (110), and (320), decreased in this order. The predominant oxide orientation was (001)Fe3O4 and [110] Fe304 A small amount of a-Fe2O3 which exhibited a fiber pattern was observed in all oxides except those formed at 250°c in low oxygen pressures. IN order to understand the properties and behavior of thin films, particularly their role in oxidation reactions, there is needed more experimental information on their structure, composition, and kinetics of formation on clean surfaces of known geometry. The present study was undertaken to obtain such information for thin oxide films formed on single crystals of a body centered cubic metal, iron. Crystals in the form of spheres were used in order to expose all possible crystal planes to the reactant gases simultaneously. Using this procedure the relative rates of oxidation of all planes could be estimated, and those exhibiting, maximum or minimum oxidation rates could be selected for a more intensive study of composition and expitaxy. Since the three types of information were obtained from the same experiment using a single crystal substrate, any differences between rate, composition, and expitaxy on the several planes may be attributed to the influence of the substrate structure. EXPERIMENTAL The starting material for this study was Armco iron rods, 6 in. long and 3/8 or 1/2 in. in diam. The analysis was reported to be 99.8 pct Fe, with major impurities listed as carbon 0.018 pct, manganese 0.027 pct, phosphorous 0.005 pct, sulfur 0.029 pct, silicon 0.005 pct, and copper 0.11 pct. These rods were cleaned with ether and heated in an atmosphere of moist hydrogen at 950°C for three days. The purpose of this treatment was to decarburize the iron and to provide a consistent, uniform grain size for the growth of single crystals. Crystals in the form of rods, up to 1/2 in. in diam and 2 in. long, were prepared by a method similar to that reported by Leidheiser and Buck.2 Spherical crystals, 3/8 and 1/2 in. in diam and having a handle about 1/4 in. in diam by 112 in. long, were machined from the single-crystal rods. After machining, each crystal was etched in aqueous nitric acid to remove the cold-worked metal at the surface. Before each experiment, the crystal was polished mechanically with metallographic papers through number 4/0, and electropolished in a perchloric acid-acetic anhydride mixture by the method of Jacquet and Rocquet.3 The crystal was washed in running distilled water for at least 5 min. The excess water was blotted with a soft paper tissue, and the crystal was placed in an all-glass reaction vessel (See Fig. 1). The crystal was heated at 550°C in hydrogen for at least 8 hr prior to the oxidation in order to reduce any surface oxides and to help relieve any stresses in the metal. For the structure and composition studies, flat faces were cut parallel to (loo), (111), and (110) planes on the iron crystal spheres. The orientation of these faces was checked by a back-reflection X-ray diffraction technique. The faces were within 2 deg of the desired orientation. The flat faces were treated as described above except that prior to electropolishing they were given an additional polish on metallographic felt saturated with twenty-minute levigated alumina. After the crystal was heated in hydrogen for at least 8 hr, the temperature was adjusted to the desired value, and the hydrogen was evacuated. Commercial oxygen which had been purified by successively passing through tubes containing magnesium perchlorate, Ascarite and magnesium perchlorate was admitted to the desired pressure as measured by a mercury manometer. A resistance-wound furnace surrounded the oxidation chamber, and a temperature controller maintained the temperature within ±3°C. The furnace was provided with a small window for observing the crystal. The changes in thickness of the oxide films were followed by observing the interference colors. The oxidation was allowed to proceed until the desired oxide thickness was attained on a given crystal plane. The experiment was terminated by evacuating the oxidation

Jan 1, 1962