Search Documents

By R. Shen

This paper presents results of a feasibility study of recycling manganese furnace dust generated in production of ferromanganese and silicomanganese at Tasmanian Electrometallurgical Company, Australia. Dried manganese furnace dust contains about 20 wt% of carbon, in average 33.4 wt% of manganese and 1.3 wt% of zinc. Manganese in the dust is in the form of MnO, Mn3O4 and MnCO3; zinc is mainly in the form of ZnO andZnSO4. Analysis of the zinc balance with dust recycling showed that to keep zinc intake at the acceptable level, it should be partly removed from the dust. In the reduction laboratory experiments, zinc oxide was reduced to zinc vapour by tar of the dust. Reduction of zinc oxide started at 800°C and zinc removal rate increased with increasing temperature; removal of zinc was close to completion at 1100oC. Optimal conditions for removing zinc from the dust include temperature in the range 1000-1150°C, inert gas atmosphere and furnace dust fraction in the furnace dust-manganese ore mixture above 60%. In the sintering of manganese ore with addition of manganese dust in the sintering pot, zinc was reoxidised and deposited in the sinter bed. Removal of zinc in the sintering pot tests was in the range 4-17%. Up to 30% zinc removal was achieved from the bottom layer of the sinter bed. It can be concluded that zinc removal will be low during the processing of manganese furnace dust in the sinter plant. The zinc removal rate will be the highest when pelletised manganese furnace dust is added to the bottom layer of the sintering bed.

Jan 1, 2007

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

By R. W. Bee

This project, sponsored by the U.S. Bureau of Mines, Division of Environment, addresses two major subjects: refuse removal and subsidence monitoring. The refuse removal task consisted of developing a methodology for selecting the most economical combinations of coal mine breaker refuse and rock banks, disposal sites and material moving systems (trucks, trains, belt conveyers and pipelines). To prepare plans for moving refuse in the Lackawanna Valley of Northeastern Pennsylvania, refuse banks were inventoried, underground disposal sites identified and unit cost data prepared for the various material moving systems. The subsidence monitoring task consisted of defining the phenomenon of coal mine induced surface subsidence, establishing operational requirements, cataloging sensors and techniques to detect and measure subsidence and testing of the most promising techniques (photoelastic patch, tiltmeter, strain gage, microseismic and precise surveying). A preliminary system for a 700 acre area in Scranton utilizing 267 grid sensors, seven microseismic sensors and precise surveying techniques was designed with initial and annual operating costs determined. Two minor tasks supported both main subjects: zoning in the Northern Anthracite Field of Pennsylvania and Technology Transfer of subsidence vulnerability prediction techniques.

Jan 1, 1972

By Weiguo Xie, MARK LAPUTKA

The pyrometallurgical industry plays a vital role in producing metals for our modern life. With growing demand of metals and declining grade of mineable ore, innovations become critical for many mining companies. It is necessary to conduct a review of recent improvements to the pyrometallurgical industry on analytical measurement techniques, process and equipment improvements, and computer-based modeling/simulations. Many of those innovations tend to be applied to wider metals, and not be restricted by a specific metal. Therefore, we tried to cover the wide applications of many improvements to wider range of metals to reflect this trend. The challenge of a lack of robust measurement techniques under high-temperature conditions within a furnace hinders optimization of a pyrometallurgical process. Some future opportunities in the pyrometallurgical industry on analytical measurement techniques, computer modeling, and processes and equipment have also been outlined and discussed.

Jan 26, 2021

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the ?bigger-the-better? design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

Jan 1, 2006

By G. Ferrara

During several years of operation in Europe, South Africa and other countries, the Tri-Flo has demonstrated to represent a substantial improvement of the dense medium dynamic separation systems. The reasons are: (1) high sharpness separation due to the multistage system and the application of new concepts in designing the regeneration circuit and controlling the medium rheology; (2) the possibility of performing two cuts at different densities using a since separation device and a single regeneration circuit. The paper discusses in detail the above mentioned points, with particular reference to the multistage technology, based on the circuit analysis theory, and to the control of the medium rheology based on recent work in the modelling, and simulation of the rheological behavior of dense suspensions.

Jan 1, 1993

By John P. Turner, Benjamin J. Turner

"Non-destructive testing and evaluation (NDT/NDE) methods have become standard tools as part of the post-construction quality assurance of drilled shaft foundations. In responding to anomalies, foundation designers, owners, and contractors face a number of choices, including: (i) acceptance of a shaft with known anomalies, (ii) further investigations of integrity (e.g., concrete coring), (iii) repair schemes, and (iv) reject and replace. To assist in selecting the best option, analyses are often performed that involve assessing the structural performance of reinforced concrete shafts that may include defective concrete or voids. Currently, the analytical tools for predicting the flexural strength and stiffness of drilled shafts with defective concrete located in discrete regions of the cross section are limited. This paper presents a robust moment-curvature analysis tool for drilled shafts based on the fiber-element discretization method. The tool allows for consideration of anomalous or defective concrete regions in the shape and location that they are believed to exist in the shaft while considering explicitly the nonlinear material behavior of the intact regions based on expected material properties. A case study is used to illustrate the practical application of the analysis to drilled shaft projects.INTRODUCTIONImperfections such as defective concrete or accidental eccentricity of reinforcing cages are an inherent part of the drilled shaft construction process that will occur occasionally even when construction best-practices are followed. Petek et al. (2002), O’Neill and Sarhan (2004), Poulos (2005), and others have described the effects that construction defects can have on the axial and lateral performance of drilled shafts. Our industry has seen rapid progress in recent years in the development and improvement of tools for detecting drilled shaft anomalies, such as gamma-gamma and crosshole-sonic logging, sonic-echo testing, thermal integrity profiling, and even visual inspection with invasive video cameras. Nonetheless, in most cases the wealth of data from these tests is used by foundation engineers to make a fairly “black or white” decision—should the defects be repaired, or should the shaft be rejected? A third option that is not typically considered is to directly analyze the section, including anomalies, and compare the reduced strength and/or ductility to the actual project demands. This option takes full advantage of the data collected during integrity testing, and may provide a justifiable means for avoiding further construction costs and delays, whether for repair or replacement."

Jan 1, 2016

By Serdar Aktaş, Özgün Küçükoğlu, Burcu Nilgün Çetiner, Mehmet Hakan Morcalı

This study compares the cementation performance of metallic iron, metallic aluminum, and metallic tin in terms of the reaction conditions and parameters in synthetic antimony chloride solutions. The effects on the antimony recovery (%) caused by the cementators’ types, stirring speed, reaction time, and temperatures were explored thoroughly. The cementation kinetics of antimony were also explored for each cementator. The activation energies were determined to be 10.99, 9.09, and 13.58 kJ mol– 1 for Al, Fe, and Sn, respectively. The results reveal that the reaction is diffusion controlled, and comparable results were obtained for each cementator. At 25 °C, 40 mg of iron powder was found to reduce all antimony ions (i.e., approx. 99% recovery), but even when 100 mg of Al and Sn cementators were used, the antimony recovery did not reach 100%. This result shows that iron is the best candidate to cement antimony out of the solution.

Jan 28, 2022

By Paul T. Allsman, William H. King

This paper describes the mineral deposits and discusses mining and milling methods and related operating conditions in an important gold , silver , lead , and zinc producing area in Ouray , San Juan , and San Miguel Counties , Colo . , embracing 250 square miles . The area is extremely rigged , ranging in altitude from 8,000 to 14,000 feet . White men first penetrated the area in 1860 , when a group known as "Baker's party " reached the Animas River at the present site of Silverton . Difficulty with the Ute Indians and severe winter conditions forced the group to leave and discouraged prospecting until 1870 when a second party reached the area and succeeded in producing 27 tons of ore yielding $ 150 a ton in gold . In 1874 , a treaty with the Indians opened the way for settlement , and mining was established . The total production of recovered gold , silver , copper , lead , and zinc from 1873 to 1947 in the three counties is valued at $347,057,047 . The greatest amount of the total production of metals has come from quartz veins in a series of volcanic flows and tuffs covering the area and comprising a blanket 4,000 to 6,000 feet thick . The igneous rocks were laid down upon an old , erosion surface and are underlain by Paleozoic and Mesozoic sedimentary rocks and pre - Cambrian metamorphic rocks . The entire series has been intruded in late Tertiary time by volcanic dikes and larger intrusive masses . Because of the great differences in relief generally , mining is con-" ducted through long adits to a depth of nearly 3,000 feet below surface in places . Walls of the veins generally stand well , and shrinkage stoping is the most common method of mining . As virtually all of the ore is sulfide below the zone of oxidation , flotation is the common method of milling . Generally , where gold is important , provision is made for its removal by jigs . Bulk concentration of the sulfides is practiced at smaller mills , but the larger operations make a selective lead and zinc concentrate or a lead , zinc , and copper . concentrate . ·

Mar 1, 1950

By F. S. Wartman

This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic Chloride with magnesium, grinding, leaching, and magnetic-separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described and some data on operating costs are given.

Jan 1, 1949

By T. Banerjee, D. Felsher, G. Leavoy

"Lake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2000 tpd tonnes per day (tpd) to over 3,000 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. Without operational data on the low aspect mill, combined with a site team that was new to SAG milling, there were many challenges in achieving the target throughput from the circuit. Through the implementation of AwaRE advanced controllers, running in closed loop with PRC fragmentation cameras as well as embedded PARC modules within the Allen Bradley PLC, the site was able to rapidly develop a best operating practise and has been successful in creating a stable and consistent operational environment. The process, lessons learned and eventual solution will be reviewed in this paper.INTRODUCTIONLake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2,000 tpd tonnes per day (tpd) to 3,150 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. This endeavor was split into two phases: the expansion of the back-end (Phase 1) and the front-end (Phase 2) of the mill. Phase 1 of the expansion was completed at the end of 2012 and involved enhancements and capacity addition to the leaching and adsorption circuits, which increased the mill’s capacity to 2,500 tpd. Phase 2 of the expansion commenced at the end of July 2013 and involved the expansion of the crushing and grinding circuits. The expanded front-end of the mill now has a capacity of 5,500 tpd, and processes ore from both Bell Creek and Timmins West mines. The updated flow-sheet, as shown in Figure 1, illustrates the replacement of the two-stage crushing and ball milling circuit with a single stage crusher and a low aspect ratio SAG mill."

Jan 1, 2015

By R. W. Hodder

"Archean lode gold deposits of both vein and chemical sedimentary types typically have major enrichments of certain rare elements, including Au, Ag, As, Sb, B, W, Se, Te and Bi, coupled with low or negative enrichments of the more abundant and mobile base metals, Cu, Pb and Zn. On the other hand, in massive base metal sulphide deposits Au, Ag, Cu, Zn and in some instances Pb are all enriched by a factor of 200 to 2000 t:'Jf'1pared to background and there is no large separation of gold relative to the base metals.The fluids from which gold was precipitated in veins were at temperatures of 320 to 480°C, at lithostatic pressure, had significant C02, and Na """" K; whereas the fluids which generated base metal deposits were at 250-300°C, at hydrostatic pressure, had C02 < < H20 and Na > > K.Many lode gold deposits are characterized by K, C02 and Si additions to their enveloping rocks, whereas base metal deposits typically have a fixation of Fe, Mg, Si and S in footwall rocks. Lode gold deposits may also have a relatively large halo of low-temperature oxidative, sadie spilitization in enclosing volcanic rocks, where seawater has later streamed into cooling stocks or flows that have initially acted to focus gold mineralizing fluids along thermal contraction fractures. The submarine environment is one hydrologically appropriate for the mixing of two initially independent hydrothermal systems, and the blending of their separate characteristics. Hence, lode gold and base metal massive sulphide deposits appear to be products of two distinctly different crustal and hydrological regimes. The former involves a high-temperature, high-pressure discharge of fluids which probably were generated during dehydration accompanying burial and progressive accumulation of volcanic-sedimentary sequences, with an additional influence of marine water in the near-sea-floor environment. The latter represents thermally driven convection of ocean water at lower temperatures and under hydrostatic conditions.Auriferous fluid systems with only minor base metal content could plausibly be generated during dehydration accompanying burial and metamorphism, when the water-to-rock ratio is low and halogen availability is limited by crustal abundance (- 60 ppm Cl). These two factors may constrain the uptake of the abundant base metals into fluids, but the solubility of rare elements is not constrained by limited fluid; and preferential uptake of Au along with other rare elements may be promoted if such elements compete more successfully for the limited halogens than the base metals, and/or have an alternative complexing agent such as CO or C()j-."

Jan 1, 1982

By Howard J. Haselhuhn

"The effectiveness of reagent adsorption onto hematite ore particle surfaces is critical during beneficiation to promote effective selective flocculation and dispersion and increase iron oxide recovery. The relationship between aqueous calcium in the process water and the effectiveness of common iron ore dispersants has never before been studied. The nature of common dispersants was studied in the presence and absence of calcium in the process water. The settling behavior of hematite-rich iron ore at pH 11 was assessed in the presence of calcium and inorganic dispersants: sodium silicate, sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP) and organic dispersant ethylenediamenetetraacetic acid (EDTA). It was found that inorganic dispersants are ineffective at a pH of 11 without activating the surface sites of the ore particles with calcium. Organic dispersants, however, were found to be effective with and without surface site activation.IntroductionThe United States produced 54 million metric tons of concentrated iron ore in 2011 (Jorgenson, 2013). Over 8 Mt were produced using a process known as selective flocculation and dispersion (CCI, 2011). The grade of this ore is slowly depleting, making it imperative that processing efficiency improves. To increase processing efficiency, a complete understanding of the effects of chemical reagents in the process must be acquired. This process relies heavily on dispersants to disperse iron oxides from gangue minerals in settling processes. The mechanism that these dispersants use to disperse the ore and its relationship to calcium in the process water has never been studied. The following extended abstract summarizes the relationship between aqueous calcium in process water and the effectiveness of common iron ore dispersants at dispersing hydrated hematite ore. These tests were carried out at a pH of 11, as this is a typical pH used to ensure dispersion in selective flocculation and dispersion processes."

Jan 1, 2015

By Louis, Jordan

THIS paper presents in an abbreviated form the chief points of interest in an investigation of the tarnish-resistant qualities of silver alloys, an investigation which has been carried out as a joint research by the Bureau of Mines and the Bureau of Standards and will later be reported in detail in an official publication from these bureaus. In 1923 a Commission of Gold and Silver Inquiry was created by a Resolution of the U. S. Senate to study the causes of the depressed condition of the gold and silver industry. In cooperation with this commission the Bureau of Mines made a preliminary survey to determine in what ways, if any, it might be possible to increase the uses of silver. One of the possibilities indicated by this survey was the development of silver alloys which should be non-tarnishing, or at least less-tarnishing, than the usual sterling silver (copper-silver). The preparation of a rather wide variety of silver alloys and the determination of their behavior under accelerated tarnish tests in the laboratory was therefore undertaken by the Bureau of Mines and Bureau of Standards as a joint investigation.

Jan 1, 1927

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year&apos;s average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017

By Dominic Orf, Gregory Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction. We were also able to observe the dissipation of the vibrations from the earthquake and see if the low frequencies, that are typical of earthquakes, dissipate at a consistent rate. Regression calculations were performed in order to see if there was a good data fit and if a specific vibration prediction could be made based on the magnitude of an earthquake. “How does quarry/mining/construction blasting compare to the Richter Scale?” This is a very common question that we get from homeowners when discussing vibrations due to blasting activities. This paper is intended to provide some simple answers for such a complicated question. Both the Richter and Mercalli scales are compared to the particle velocities as they were recorded from this earthquake.

By C. Blawert

In previous studies of various HPDC magnesium alloys we found that the corrosion properties of the skin are inferior in comparison to the bulk, However, this is surprising as one would expect better corrosion properties for the finer microstructure of the skin, In a more detailed study using 2 and 6 mm thick sections from HPDC AZ91 step plates, the corrosion results of the original skin, the slightly removed skin and the bulk were compared, Indeed, the corrosion measurements including potentiodynamic polarization, long term polarization resistance measurements and electrochemical impedance spectroscopy (EIS) revealed a lower corrosion resistance of the original as-cast skin. An explanation for this corrosion behavior was found, on the one hand, in the microstructure concerning especially the amount and distribution of the 13-phase and, on the other hand, in the composition, including the distribution of the most important alloying element Al and of some impurities such as Fe.

Jan 1, 2005

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By E Coffison, M Gibbs, C Bennett

The sustainable management of surface water associated with coal mining and coal seam gas projects is a considerable factor affecting the global competitiveness of these resource companies operating in Australia. Management of surface water can be costly, but effective water management and hence environmental stewardship enhances corporate social responsibility and the social license to operate. The surface water issues for the two industries are comparable, yet there is currently a lack of alignment between how Queensland, where the majority of AustraliaÆs coal seam gas projects are located, manages and regulates water on coal mine projects and coal seam gas projects.This paper provides a high level comparison of Queensland legislation and highlights the lack of alignment of this legislation regarding surface water management in these two industries. Through a case study, it looks at the surface water management process at a coal mine site based on the current legislation and principals of surface water management. QueenslandÆs lack of alignment in legislation regarding surface water management in these industries is understandable given the different development paths and time scales of the two industries. The coal mining industry has developed over a long period of time and the legislation has progressed in parallel, whereas, the coal seam gas industry is relatively new in Australia and the legislation has had to advance quickly. The lack of alignment between management of surface water for the two industries creates confusion among stakeholders and this adds complexity and additional transaction costs during the exploration, permitting and operational phases of projects, including landowners who may be affected.CITATION:Bennett, C, Coffison, E and Gibbs, M, 2013. Lack of alignment between regulation of surface water management in coal mining and coal seam gas, in Proceedings Water in Mining 2013 , pp 157-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013