Search Documents

By David C. Laurence

in March 1999, the School of Mining Engineering at the University of New South Wales carried out a series of underground trials using " Evermine", a South African developed two-part water based polymer membrane. The aim of the trials was to determine the potential of a spray-on polymer membrane such as Evermine as an alternative to conventional rib support systems The mine selected was Angus Place colliery, reputed to have some of the worst ground conditions of any Australian underground coal mine. Ribs at Angus Place are supported by conventional pattern bolting supplemented by wire mesh. The trials indicate that there is significant potential for the introduction of polymer membranes into the underground coal minim; industry Initial results indicated that ribs that had been sprayed exhibited less displacement and spalling than unsprayed ribs. particularly when subjected to abutment loads from an approaching long-wall Further research will he required to conclusively rate the performance of Evermine in comparison to other products in the market and the long term performance of the product

Jan 1, 2000

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms around a longwall gate-road system in an underground coal mine. Of particular interest was roof deformation over the headgate entry. The strata above and below the coal seam are very weak, carbonaceous mudstones that have planes of weakness oriented along the bedding. Visual observations of previous gate roads over several years suggested that deformation was time dependent and resulted in creep along joints or crack growth. Instruments were installed at a test site to measure deformation around the entry, strew changes in the pillar, and loads transferred to support systems. Multipoint extensometers, instrumented bolts, instrumented trusses, biaxial stressmeters, borehole pressure cells, and single-point extensometers were installed. Monitoring continued until the longwall face passed the test site by 38.7 m (127 ft). Results show that fracture zones arched over the entry from both ribs, most bolts and trusses were loaded past their yield point, and the largest change in secondary principal stress was almost horizontal in the pillar. Displacement measurements in the roof showed classic primary creep.

Jan 1, 1995

By Christopher Mark

After the United States and Australia, South Africa has the largest. modern underground coal mining industry in the world. Historically, South Africa has been the cradle of many innovations in ground control, particularly in the area of pillar design. Today, South African mines are grappling with many of the same issues faced by their U.S. counterparts, including safety during pillar retreat operations, selecting the proper roof support, and maintaining long-term pillar stability. The author recently visited seven underground mines in the Mpumalanga, Free State, and KwaZulu-Natal provinces. Mining methods included longwall, room-and-pillar with continuous miners, and drill-and-blast. The mines represented a cross-section of geology and ground support practices. At each mine evaluations were made of the Coal Mine Roof Rating (CMRR), roof support practices, pillar design methods, and general ground control experience. The coal seams observed were generally thick (2-5 m), the depths of cover moderate (less than 200 m), and the roof rocks relatively strong (CMRR greater than 45). Unfortunately, the South African roof fall fatality rate is approximately three times greater than in U.S., perhaps in part because roof bolts seem to be more widely spaced in most South African mines. Roof bolting equipment was generally outdated, and the quality of bolt installation was a major concern. Pillar design, on the other hand, is quite advanced, and pillar failures are rare. Several novel partial pillaring techniques are employed, including "checkerboard" mining in which every other pillar is removed, 3-cut systems, and high-extraction mining where engineered final stumps are left by design. The paper also offers observations on ground control management techniques (including recently introduced Codes of Practice), the role of the mine inspectorate, and the status of the research community.

Jan 1, 1999

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

By P. K. Kaiser

The purpose of deformation monitoring for the evaluation of the stability of underground openings is reviewed briefly and some results from laboratory tests of small tunnels are presented. The ground behaviour is described by comparison with the response of structural systems and illustrated by the data from the testing of small tunnels. It is concluded that the main objective of a deformation monitoring system for stability evaluation is to determine the actual process of deformation and instability in the area surrounding the opening. Only when this process has been established is it possible to use deformation measurements to design support systems or to improve construction or mining procedures. Present monitoring practice is not sufficiently orientated toward the aim of process description.

Jan 1, 1981

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

During the last decade mechanical rock excavation has become increasingly widespread in the mining industry and, more in general, in excavation engineering. This technology, especially the tools and their operating mode, has developed according to empirical procedures and for this reason their validity should be ascertained by systematically re-examining the rock breakage processes. This topic has been approached in the framework of a joint research project involving the Universities of Cagliari (Italy) and Wollongong (Australia). The investigation has been carried out experimentally as well as with the methods of numerical modelling which is based on fracture mechanics principles. The first results of this integrated research led to the proposal of an interpretation of rock breakage by means of drag tools and to the identification of a basic correlation between the rake angle of the tool and the grain size of the rock fragments produced and, therefore, the energy efficiency of the operation.

Jan 1, 1990

By N. P. Kripakov

The U.S. Bureau of Mines (USBM) is conducting research to develop a practical computer-based tool that will allow coal mine planners to anticipate rock mass behavior surrounding mine entries prior to actual mining. More specifically, this tool estimates to what degree and extent the immediate roof and floor strata and the coal pillar ribs surrounding an opening will weaken or fail for a given set of mining parameters. The technical approach couples together two numerical techniques: the boundary-element method and the finite-element method to allow for an approximate three-dimensional simulation of actual mining situations. Outputs from plan-view, linear-elastic, boundary-element models executed at different mining stages are used as input to a detailed, section-view, finite-element model to estimate the degree and extent of failure expected to occur around the periphery of an entry system. Using a pseudo-elastic approach. elastic rock mass properties are continually updated as different zones are predicted to fail. The procedure is relatively easy to use and is being set up to work interactively with the user who will not be expected to be a computer expert. Inputs include easily understood parameters obtainable from the field and rock mechanics laboratories. Examples of computer-generated output from generic sample models representing typical mining situations are presented and results discussed.

Jan 1, 1994

By J. S. Oram

Maltby Colliery, operated by RJB Mining (UK) Ltd is successfully mining the Parkgate seam in Yorkshire at a depth of 1000m using longwall retreat. Extraction in the Parkgate seam is influenced by interaction from previous workings in the Swallow Wood Seam 160m above. The paper describes in-situ stress measurements and simple gate road convergence measurements carried out to assess the extent of the interactive influence. The stress measurements, obtained using the stress relief overcore technique, were carried out from a maingate development roadway in an area where the stress redistribution under an overlying pillar and adjacent panel goat could be measured. The measured vertical stress distribution confirmed a significant interactive influence with high imposed vertical stresses under the overlying panel edges. Simple roadway convergence monitoring stations established in the gateroads of a retreating panel and in the development gateroads of the adjacent panel, confirmed higher rates of roadway deformation relating to overlying panel edges and pillars, particularly in the areas where a vertical stress window developed during panel retreat. In addition to highlighting a close relationship between closure rate and the measured vertical stresses, the convergence monitoring proved valuable in establishing characteristic deformation behaviour under specific interactive influences and also in defining the optimum location, extent and time of installation u£ additional roadway support and reinforcement. The information from the measurement programme has enabled the Mine Management to gain a better understanding of the interactive influences on roadway behaviour and was instrumental in designing the layout of panels in an area of the North East district of the mine where previous experience had indicated the combined influence of high interactive stresses and weak roof lithology resulted in difficult strata conditions both at development and on panel retreat. The planned location of panels and gateroads took into account both mining operational considerations and the need to avoid potentially high risk interaction zones as highlighted from analysis of the monitoring results. To obtain additional data on parameters influencing roadway deformation, extended roadway convergence monitoring has been established.

Jan 1, 1997

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004

By D. Newman

An underground limestone quarry, developed in the 1940's, transitioned from a surface quarry to an underground room-and-pillar operation. The quarry expanded to a second underground level when the reserves on the first level reached the property boundaries. The historical basis for the sill pillar thickness between the first and second level, pillar dimensions, and mining height was lost during the course of several changes in ownership. When reserves on the second level reached a five-year life, and plans were initiated for a third level, quarry management embarked upon a thorough evaluation of i. current ground control practices for the support of the immediate roof, ii. roof support in the declines between the surface, Level 1, and Level II, iii. pillar centers and pillar safety factors, iv. pillar alignment between levels, v. mining height within a level, and vi. the locations of declines to access future reserves on level three. The evaluation began with detailed mapping of the location and orientation of calcite veins, joints, fractures, and ground conditions in the immediate roof of Level II. The orientation and location of calcite veins, joints, and fractures on Level II were compared with similar mapping on Level 1, completed in the 1970's to establish whether these features were continuous and would be expected to affect conditions on Level III. Rock strength, physical properties, and fracture spacing were obtained from two (2) diamond core holes drilled from Level I to Level II and two (2) holes drilled from Level II to define the vertical extent of future reserves on Level III. The effort to characterize geological conditions was expanded to a rock mechanics investigation of the: i. performance of the current roof support, ii. optimization of roof and rib scaling, iii. calculation of safety factors for 416 pillars on Level II, iv. evaluation of future pillar centers and mining height within a level based upon pillar strength and pillar geometry, v. development of beam safety factors for the immediate roof on Level II, vi. identification of the most suitable strata for the roof in the future level three, and vii. use of LAMODEL to develop a large numerical model of overburden, inter-level, and total stress on the pillars in levels one and Level II with a stress "footprint" on the proposed level three. The characterization of engineering parameters and geological conditions resulted in changes to the: ? active operations in Level II regarding scaling ? equipment and scaling practices, ? pillar centers, ? mining height, ? raising the immediate roof horizon to avoid ? laminated strata in the current roof, and ? a change in rock bolts from a friction based system ? to active tensioned rebar. The planning and design of level three is ongoing and relies heavily upon the geological and engineering investigations conducted during the past year and one-half.

Jan 1, 2001

By N. P. Kripakov

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north-central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield-pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)-wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By Hai Rong

EH-4 Electrical conductivity imaging system has been playing an important role in prospecting, looking for water resource, and determining coal mine gob boundary by virtue of its significant advantages such as collection of large volume of data, light weight, fast analysis, high-precision, and low cost. However, it has little application in determining the overburden failure zone and development of water flowing fractured zone and bed separation space in complex extra thick coal seam conditions. In order to confirm the overburden failure range and evolution of water flowing fractured zone and bed separations in complex extra thick coal seam conditions the panel 63005 of Laohutai coal mine in China was selected for study in this paper,. EH-4 magnetotelluric method was used to determine the overburden failure zones and bed separations in the overburden. Theoretical analysis and numerical simulation were employed to verify the EH4 survey results. The results show that the failure height in the overburden of the three coal splits was 120m to 170m before panel mining, and increased to 150m to 220m after panel mining. The overburden failure height was on average 7.4 times the equivalent mining height in complex extra thick coal seam condition of Laohutai coal mine when the sand backfilling and fully mechanized top coal caving methods were employed. After mining of panel 63005 started, bed separations were found on the hanging wall and footwall of the F18 fault where water bodies existed. The results obtained in this research not only provide a theoretical guidance for safe mining at Laohutai coal mine but also serve as a reference for predicting and preventing water inrush accidents for coal mines under similar condition in China.

Jan 1, 2014

By J. A. Nemcik

Although floor failure at longwall faces has been traditionally associated with a soft floor, in many csses floor buckling has been observed just ahead of the longwall supports, despite the floor being a competent rock The floor failure is associated with the presence of weak bedding planes in the floor and the movement of strata towards the goaf opening. This paper presents the principles of the floor failure based on numerical modelling and field observations and outlines the practical approach to estimate the risks involved with floor failure.

Jan 1, 1995

By Radoslaw L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps often results in localized slope failures. The Bureau of Mines has developed a computer code based on a rigorous limit plasticity approach which determines the admissible total weight for a concentrated loading near the crest of these otherwise stable structures. The program is based on a three- dimensional analysis and provides an upper bound solution to the load that can be applied to the top of the operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism, and the use of the computer code based on this approach for mining applications.

Jan 1, 1990

The challenge of planning to minimize interaction effects in multi-seam mining is compounded by the difficulties inherent in extrapolating essential geological and spatial data between sampling points. To predict the effects of ultra-close mining on lower seam entry stability, simulated mine openings were studied using finite element analysis and body loaded photoelastic models. Both symmetrical and unsymmetrical loading was used to represent stress fields generated under multi-seam conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Stability predictions require precise definitions of geologic and spatial data, which could not be accurately defined by interpolation between sampling points. To overcome this problem an expanded roof stability model, SESAME2, was developed to incorporate reliability concepts based on Monte Carlo sampling. The model was demonstrated in terms of variations of innerburden thickness using a case study.

Jan 1, 1994

By John Bullock

Limestone and dolomite quarries were mapped to determine specific failure mechanisms for the various geologic and structural conditions. Algorithms for analyzing these mechanisms were incorporated into a software package together with ranges of physical properties such as joint shear strength, angle of internal friction, and cohesion for specified lithologic units. Reliability options using Monte Carlo sampling and sensitivity studies are included to evaluate alternative highwall designs. The package is designed to facilitate progressive stability evaluation of quarry highwalls as mining continues. This package includes an optimum design protocol that can be followed to avoid the potential of massive failure. The program was developed in conjunction with the quarry industry and is demonstrated using case studies.

Jan 1, 1993

By G. K. Rogers

Portals, which are the surface entrances to underground excavations, are frequently overlooked and often difficult areas In terms of ground control. Failures commonly occur In the typically high angle approach cuts and Initial subsurface portion of the portal. In order to permit rigorous design of all types of portal structures, failures are Identified and subsequently classified. Based on the failure classification and suggested analysis methodology, optimum ground and support loading can be determined.

Jan 1, 1988

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By John C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1994