Search Documents

By M. van Biljon

The possible closure and subsequent flooding of South Deep Gold Mine?s neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding South Deep mine. Several technical investigations had been carried out before and during construction of the plugs in order to reduce the probability of groundwater flow through the boundary pillar between the two mines or through the rock mass immediately around the plugs. This paper describes the geological, hydrogeological and stability investigations carried out to evaluate the structural competence of the boundary pillar.

Jan 1, 2006

By K. Gharibi, A. Dehghani, S. Farrokhpay, M. Aghajanloo, M. Ostadrahimi

The effect of flotation operational parameters on froth stability and froth recovery was studied. Froth stability was measured using a special column. To determine the froth recovery, the froth height change model and froth height exponential model were used. It was found that since the interactions between the pulp and froth zones affect the time of froth formation, the exponential model is more suitable than the froth height change method for determining the froth recovery. The results showed that superficial air velocity and collector dosage have, respectively, the highest and lowest effect on the froth recovery, while froth recovery decreases sharply with increasing froth height.

Jan 1, 2021

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

By V. Moodley

Strict implementation of International Standards for representative sampling of coal is difficult for routine monitoring, due to time, technical, and economic constraints. A large percentage of the total sampling variance arises from errors accumulated during the earliest stages of sample collection. Modified procedures on the precision of the final result leads to controversies between the sellers and customers for coal. Manual collection of coal samples violates the principle of correct sampling, that all fragments must have an equiprobable chance of being in the sample. In addition, manual size reduction of large numbers of samples is time consuming and involves human errors. A coal quality management procedure in alignment with the relevant ISO standards that describes the sampling protocol has been implemented, and current sampling and laboratory analysis of coal from base load mines (mines situated at the mouth of the power station) are well established. For import coal, sampling is performed during unloading by auto-mechanical sampling (AMS). Due to logistical and safety issues associated with multiple suppliers, Eskom opted for the coal to be sampled at source on a pre-certification basis. Online analysers provide a fast, accurate, real-time method of determining the total moisture and elemental composition of coal and is important to the coal industry for pricing, quality control, and reduction of SO2 emissions. Elemental analyses include S, Si, Al, Fe, Ca, Na, Mg, Mn, Ti, K and Cl. Measurement of S is dictated by the control of SO2 emissions from coal-fired power plants. Elements such as Na and Cl have adverse effects on boilers, causing fouling and slagging. Available online elemental analyser technologies include prompt gamma neutron activation analyses (PGNAA), recommended for major element determination, and pulsed fast and thermal neutron analysis(PFTNA), that is capable of measuring the major and minor chemical elements contained in coal. These systems utilize nuclear reactions to produce characteristic gamma rays that are used for identifying various chemical elements. By acquiring the gamma rays in three different time windows, there is a significant reduction of the background as compared with the spectra taken with a radio isotopic source.

Jan 1, 2009

By A. Çelik

Wheel loaders are widely used in many sectors due to their mobility, operational flexibility, and low costs. The literature is mainly focused on improving the hydraulic, mechanical, and electronic subsystems of these machines in terms of efficiency or developing strategies for controlling these systems. In this study, the effects of the loader operator and different working conditions on the loading performance were investigated. The study was carried out at the Can Lignite Enterprise (CLI), which is a major coal producer in Turkey. In the study, which lasted approximately four months, a total of 808 measurements were performed to investigate seven different scenarios. The effect of a single parameter on loading performance was investigated in the first six scenarios. The results showed that the biggest impact on loading performance was caused by the operator's experience with 63.4%. On the other hand, the worst and most ideal working conditions determined from the first six scenarios were tested in the seventh scenario. It was tested as a script. The test results showed that the loading performance was 285.5% more effective under the most ideal operating conditions compared to the worst operating conditions. In addition, in the study, the loading performances of five loaders with four different capacities were examined in terms of energy efficiency and it was determined that the Kawasaki 115 work machine, which has a higher model and lower engine operating hours, was more advantageous. In the study, various suggestions were developed in parallel with the research results. The most prominent and easiest to implement of these suggestions is related to the selection of the loader operator.

Nov 27, 2024

By D. R. Hack

The complexity of commercial mining software has gained rapidly over the past decade as hardware developments have surpassed software capabilities at a staggering rate. Software users, recognizing the limitations of off-the-shelf applications, have adapted embedded scripting languages. Custom programming has always had a vital role in mine computing innovations, yielding a dynamic research environment in industry and academia. Fields such as industrial minerals can benefit from customization of existing software, since the majority of mine planning software was designed for large metal mines. Different customization approaches utilizing embedded scripting languages are presented, with examples of sand and gravel applications in development. Following implementation by Surpac and development of the Surpac Command Language, Tcl has been widely applied. Mintec introduced Python, also extensible and portable amongst various operating systems, for use in their MineSight products. In early 2000, Gemcom introduced the use of Microsoft Visual Basic for Applications, widely used customization tools for a decade. Datamine implemented a flexible multi-language approach, with all program commands and processes available through the COM Server Interface. This extends customization from the existing macro language to scripting in HTML, JavaScript, or any language that supports COM.

Jan 1, 2003

"The management of outlier grades in positively skewed gold distributions is a contentious issue. Incorporating outliers in standard ordinary kriging (OK) estimation procedures in a way that honours the data without smearing extreme grades into surrounding areas has been problematic. Cutting or capping of outliers to mitigate their influence in estimation techniques is common practice, while methods that manipulate the OK system of equations fail to honour the data. We propose a method of post-processing of kriging weights that provides realistic OK estimates and mitigates smearing without manipulating kriging equations or changing the original grades. The method requires that the data is not clustered, is approximately equally spaced, and is of the same support. Positively skewed data is ordered on attribute grade and nonlinearly transformed to a Gaussian histogram of categorical bins whose frequency is based on their likelihood of occurrence and location in the sample distributions. Factors that restrict kriging weights are calculated by dividing the percentage frequency of data in each bin by the percentage frequency of data in the bin with the highest frequency. Restriction factors applied to the kriging weights in the OK estimation restrict the range of influence in proportion to their probability of occurrence in the distribution. Smear reduction post-processing is easy to implement and addresses issues arising from negative kriging weights while considering the spatial location of samples, the sample grades, and their probability of occurrence. The method mitigates both smoothing and conditional bias.IntroductionOutliers are sample observations that deviate considerably from the standard or expected (Hawkins, 1980). These deviations can be high or low in grade depending on the distribution. The presence of outliers in a mine sampling campaign could provoke mixed reactions. Mining engineers might view high-grade outliers as a promise of achieving higher grades, while the geostatisticians view outliers as affecting the accuracy and precision of the overall estimate, among other issues. Having identified outliers, the geostatistician must decide how to account for their presence and treat them so that true underlying estimates are not distorted. Advanced knowledge of the deposit allows the geostatistician to identify and treat outliers acceptably, especially where samples are limited in number and the true grade distribution is uncertain. If ignored, or treated incorrectly, outliers are likely to lead to smearing of extreme grades into the surrounding estimates, thereby steering regions towards potential under- or over-estimation."

Apr 1, 2019

By A. Tsekov, Stefan Neufeind, T. Angelov, G. Savov

"A complementary ion exchange/solvent extraction process for the recovery of copper from low-grade ores developed by Iontech Engineering Ltd. is described. It has successfully been implemented on a full-scale plant level at the Buchim Copper Mine in Macedonia, yielding a maximum copper cathode production of 2400 tonnes per year. Technical and economic aspects of three years of operational experience are comprehensively compared with the Asarel Medet copper plant in Bulgaria, which is utilizing conventional solvent extraction in the enrichment/purification step. INTRODUCTION The concentration and separation of copper from primary leachates is one of the key operations in the hydrometallurgical processing of oxide ores (Langner, 2011). Conventionally, this basic operation is conducted by submitting the pregnant leach solution (PLS), with a 1–5 g/L Cu content, from the initial sulfuric acid leach to a solvent-extraction (SX) process in which copper reports to the organic phase (see Figure 1). After phase separation, the metal is stripped from the extractant/diluent mixture employing sulfuric acid to furnish a concentrated metal solution, usually containing 40–50 g Cu/L. The final products of the overall process are copper cathodes, which are obtained from a terminal electrowinning step.Although considered as “technology of choice”, SX to date is still suffering from several drawbacks, such as the risk of poor phase disengagement and the high capital costs of solvent-extraction plants. Especially, the processing of leachates with lower copper tenors (< 1 g/L) is often economically less attractive. As a result, tremendous efforts have been dedicated to the evaluation of alternative technologies to address these challenges."

Jan 1, 2015

By Baojun Zhao

Primary lead production using the lead blast furnace in conventional practice is carried out using sinter feed. At YMG, China, the sinter plant has been replaced with a lead ISASMELT furnace. The ISASMELT furnace produces lead bullion plus a high-lead slag, which is cast into lumps to provide a suitable feed for the blast furnace. In the present study the relative microstructures and reduction characteristics of industrial lead sinters and synthetic ISASMELT slag in CO/CO2 gas mixtures have been measured and compared. The microstructure and property changes, and the mechanisms of reduction in each case are examined and discussed. The results of the study are used to explain the successful implementation of cast slag feed in commercial ISASMELT- lead blast furnace practice. Key words: lead slag, lead sinter, lead blast furnace, reduction kinetics and mechanisms

Jan 1, 2008

The main objectives of the Mine Mechanisation and Automation program (MMAP) are to enhance health and safety in underground mining operations, facilitate mechanization and automation in narrow-vein and deep mines, provide sound science to regulatory agencies and improve mine profitability. The program, which has a unique underground and surface industrial scale facility, is involved in many multi-partner projects, like hydrogen fuelcell applications, electrification and hydraulification of underground mines, reduction of noise and vibration, miner location device, explosive-free blasting and hoisting. The paper presents an overview of the Mine Mechanisation and Automation Program of Natural Resources Canada and some of the main projects.

Jan 1, 2002

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By C. Sahyoun

The influence of microwave treatment on copper flotation has been investigated. Comparative batch flotation tests carried out on ore treated at 5?12 kW for 0.1?0.5 s showed that improvements in copper recovery of between 6?15 % could be achieved compared with untreated ore. Both recovery and cumulative grade increased with increasing treatment time and power. A preliminary economic analysis showed that microwave treatment will be economically viable if recoveries similar to those determined on laboratory scale can be achieved on a plant. Keywords: microwave treatment, copper ore, flotation, liberation, recovery

Jan 1, 2005

By K. Collett

Elandsrand started shotcreting back in 1991. This paper will share the experiences of the mine by looking into the past, the present situation and the way Elandsrand plans to approach the future. It looks at the application of drycrete and discusses the factors that led to the introduction of wet fibre reinforced shotcrete. The logistical constraints of getting shotcrete material underground will be solved by the development of an underground batch plant, using run of mine waste rock as an aggregate.

Jan 1, 1998

By Raphael Banda

1 Initiating Systems ? a definition An initiation system is a combination of explosive devices and component accessories specifically designed to convey a signal and initiate an explosive charge from a safe distance. In the use of explosives, the initiating system performs the functions of transmission and control of the firing signal to each explosive charge. As functional groups, initiating systems may be considered as: Starters Those which provide the initial signal to start the blasting process. Surface systems Products which provide transmission of the starter signal and delay timing (if any) across the surface of the blast outside the blast hole. In-hole systems Products which provide the signal transmission, delay timing (if any) and the initial explosives energy in the blast hole.1 2 Different types of Initiating Systems The initiation systems commonly used in Sub Saharan Africa are: ? Detonating cord and detonating relay systems ? Capped fuse and igniter cord systems ? Shock tube non electric systems ? Electric systems ? Electronic detonators 3 Overview of Electronic Delay Detonator Technology Conventional detonators use pyrotechnic delay elements and the variation of the actual delay periods is at best approximately 1% the nominal delay. The lack of guaranteed precision common to all pyrotechnic systems enhances the likelihood of negative environmental blasting effects.3 For example, take a 500 ms in hole delay. In conventional detonators this means that 95 % of shots fire within 10 ms of the mean. i.e. a window of 20 ms. Taking a fixed interval between shots of 25 ms, with a range of ± 3 ms, a very ragged firing pattern could be expected which in practice would result in non uniform fragmentation.

Jan 1, 2005

By C. Musingwini, M. Mohutsiwa

"SynopsisCapital cost estimates are important in decisions on whether a project will be approved, mothballed, or abandoned. In South Africa, junior coal miners do not have extensive databases of historical projects from which to estimate capital costs. The purpose of this paper is to establish formulae that can be used for estimating capital costs of developing coal mines in a coal-producing country, using South Africa as a case study. The costs are estimated to an error of magnitude level of -30% to +50%, which is suitable for a concept study level, using a parametric estimation technique. The study uses data from completed coal mining projects from selected coal-producing countries. Three formulae are developed and presented for estimating capital costs of underground bord and pillar, surface shovel and truck, and dragline operations.IntroductionCapital cost estimates play a critical role in deciding whether projects will proceed, be delayed, or abandoned. It is therefore important that capital cost estimates are carried out accurately as determined by the estimation guidelines based on the level of estimation conducted (Shafiee and Topal, 2012). The lack of literature on estimation of capital costs in many coal mining countries is adversely affecting junior coal miners, since they do not have an extensive database of historical projects on which to base estimations. In South Africa, the difficulty in estimating capital costs is attributable to lack of publicly available data on completed South African mining projects (Hall, 2013)."

Jan 1, 2015

By S. K. Murphy

A partial shaft pillar extraction project was embarked on at a mine in the West Wits mining region in South Africa. Prior to the extraction, a rock engineering assessment was conducted with the main objective being to establish which areas of the shaft pillar could be extracted without unduly affecting the stability of major infrastructure within the shaft pillar. Standard numerical modelling methods were used to conduct this assessment and several areas were identified for extraction. However, during the extraction process, it was found that the infrastructure was affected more than was originally predicted by linear elastic modelling. In addition to this, several large events resulted in far more large aftershocks than would normally be predicted. In order to gain an understanding of this phenomenon, seismic data was integrated with numerical modelling as follows: > The seismic data in the form of displacements was integrated in 3D space within the model to assess the effect of static stress changes associated with seismic activity > Data from large events was integrated onto specific structures, where displacements associated with large events were integrated onto the plane of structure in question. This paper describes the methodology and results obtained from each of the above processes and include insights into the mining process that were previously unfathomable using standard linear elastic numerical modelling. The way forward for this rock engineering assessment of partial shaft pillar extraction is also discussed.

Jan 1, 2012

By M. Abdellatif

Keywords: Pyrometallurgy, furnace, DC arc furnace, smelting, silicon The technical feasibility of silicon smelting in a DC arc furnace was investigated. A graphite-lined furnace was operated at power levels of 150 to 160 kW, and 40 to 60 V. The average feed rate during the silicon production period was about 30 kg/h. The recipe consisted of pre-mixed batches of 28% petroleum coke and 72% lumpy silica. The target furnace operating temperature was set at 1600°C and then raised to 1700°C. In total, about 1.6 tons of premixed feed materials was processed over 16 feeding?tapping operations. The feed was manually charged into the furnace in sub-batches of 10 to 40 kg at a time. The total batch mass was set at 90 kg during the initial part of the testwork, and increased to about 120 kg for the rest of the campaign.

Jan 1, 2011

By F. Peer

In most coal preparation processes, water is a necessary medium, but the presence of water in coal after it has been cleaned has a negative impact on transportation costs, handling and specific energy values. The utilization of super absorbent polymers (SAP) in the nappy application is well known. The concept of utilizing these polymers was investigated for the purposes of dewatering coal and other fines, generated by preparation processes such as flotation. SAPs are granular highly cross-linked synthetic copolymers with excellent water-absorbing properties. The dewatering process is characterized by three main stages: (a) contact of super absorbent polymer with high-moisture fine coal; (b) separation of dewatered fine coal from super absorbent polymer; and (c) regeneration of used super absorbent polymer, by exploiting its response to changes in conditions such as pH or temperature. Preliminary tests showed the separation step to be very difficult. The novel idea of encasing a given amount of polymer in a water permeable cloth solved this problem (of separating the swollen polymer from the dewatered coal). Preliminary tests investigating the effectiveness of the sachets of polymer showed a drastic decrease in the moisture contents of slurries. Furthermore, it was shown that it was possible to regenerate the polymer (still within the sachets) through thermal drying. A full-scale experimental programme was then followed to accurately determine the feasibility of using sachets of SAP. The experimental variables were initial slurry moisture content and polymer dosage. It was observed that the sachets seemed to work fastest and most effectively at high moistures and also at higher dosages of SAP. Regeneration of the polymer was also investigated, using two methods: thermal regeneration and pH-induced regeneration. The experimental variables, for investigating the regeneration process, were method of regeneration and grade of water used. Thermal regeneration at 70°C seemed to work successfully. Although the cost of using thermal energy is still a problem, the safety aspect (fire hazards) has been addressed since the polymer does not ignite when heated, unlike fine coal particles that may do so. The alternative method of regeneration, which exploits the pH-sensitivity of the polymer, was less successful, and further work needs to be conducted.

Jan 1, 2003

By W. J. Errington

The Isasmelt process was developed at Mount Isa Mines Limited in Queensland, Australia in collaboration with CSIRO, the Australian Government research organisation. Originally developed for primary lead smelting, culminating in the construction of a 60,000 tonnes per annum lead smelter at Mount Isa, this technology now also provides a major part of the current 200,000 tonnes per annum copper smelting capacity at Mount Isa. A programme is now in place to expand copper production to 250,000 tonnes per annum. The technology has also been applied to secondary lead smelting at Britannia Refined Metals, a MIM subsidiary company, where a 30,000 tonnes per annum lead plant based on battery scrap feed has been operating since 1991. Mount Isa Mines Limited decided to license the technology in1988, and copper smelting plants utilising Isasmelt technology are now operated by Cyprus Miami Mining Corporation in the USA and by Sterlite Industries in India. In addition, the technology was adopted by AGIP for smelting copper/nickel concentrates in Australia. Union Miniere are currently constructing an Isasmelt furnace to smelt and convert copper-containing materials at their plant at Hoboken in Belgium. This paper discusses these developments and also some likely future developments which include the application of the technology for continuous copper and nickel converting and applications in the treatment of zinc-containing residues.

Jan 1, 1997