Search Documents

By Lon D. Santis

This paper presents data and theorem to calculate the risk of experiencing undesirable lightning related events while blasting or while engaged in other lightning sensitive activities. The paper provides an overview of lightning hazards in blasting operations and a brief history of lightning related blasting accidents. Lightning continues to be the primary cause of premature initiations of explosives in mining; on average, over two such incidents are reported to the Mine Safety and Health Administration (MSHA) each year. The energy contained in lightning discharges and how this energy sets off explosives in mining is presented. Three categories of lightning warning methods: public media, lightning detectors, and atmospheric electrostatic field measurement are discussed. The remainder of the paper presents recently acquired data on the spatial characteristics of lightning development. This data is used to estimate the risk assumed by blasters under certain conditions. Risk estimations are made for electric and nonelectric blasting if persons are evacuated when cloud-to-ground (c-g) lightning approaches within a certain distance. For example, about 0.6% of all c-g lightning strikes have no other c-g lightning strikes within 25 miles in the previous 30 minutes. The paper shows that a typical blaster using nonelectric initiation in a high lightning density area with a 100% accurate lightning detector set to alarm at 25 miles would have a lightning caused unplanned detonation every 14,000 years.

Jan 1, 1998

By Martin Chenoweth

The Metropolitan Water District of Southern California (MWD) is undertaking one of the nations largest water management projects. The Eastside Reservoir Project is being built to insure a supply of water to Southern California in the event of earthquake damage to the aqueducts supplying the region. An 800,000-acre-ft lake will result from the three dams, closing off the valley between two parallel ridges. The single largest contract of the project, the West Dam, was awarded to the joint venture of Atkinson Construction Co., Washington Construction Co. (Morrison Knudsen Co.), and HB Zachry Co. Over 50 million bank cubic yards of rock must be drilled and shot on this contract alone. AWZ relies on the TechBASE database management system for documenting drilling and blasting. The database format of TechBASE allows all production parameters to be linked to the location of the activity. This allows parameters such as drill penetration or boulder production to be analyzed for geologic trends that can either be exploited or dealt with. Shot locations are stored as 3D polygons in a polygon table. Production and cost data are stored in flat tables. Shot names are unique and link the polygon table to the flat table. This allows typical database queries to be made by date, location, cost or any production parameter. The output from these queries can be presented in table, graph and as map formats. The map output is particularly helpful in quantifying geologic conditions and blast performance. The ability to transform the data into information has been very helpful. The ability to present this information graphically has been invaluable.

Jan 1, 2000

By Fumihiko Sumiya, Yuji Ogata, Masahiro Seto, Yukio Kato, Yuji Wada, Kunihisa Utsuyama, Yoshikazu Hirosaki

It is well known that emulsion explosives can be dead-pressed especially in underground blasting. Voids in emulsion explosives will affect such malfunction of explosives. To clarify the factors that affect the dead-pressing phenomena, the characteristics of the pressure wave propagation in emulsion explosives were investigated. Three types of microballoons .or microbubbles, glass microballoons(GMB), resin microballoons(RMB) and chemical gas bubbles, were used as sensitizers for emulsion explosives. The pressure profiles inside the explosives were measured to determine the effects of the microballoons or microbubbles contained. The underwater explosion test and the large-scale drop hammer test were carried out to load the explosives with a dynamic pressure and a quasi-dynamic pressure respectively. In the underwater explosion test, the pressure profiles in the emulsion explosives were measured by a piezo-electric pressure gauge inserted to the center of the explosive cartridge which had a diameter of 30mm. In the large-scale drop hammer test, the same type of pressure gauge was placed at the bottom of the explosives. From these experiments, the following results were obtained ; A) The pressure profiles in the sample explosives sensitized by RMB or chemical gases were sharp, while in the sample explosives sensitized by GMB the profile was broad. B) The peak pressure levels in the sample explosives sensitized by RMB or chemical gases were twice as high as that in the sample explosives sensitized by GMB in the underwater explosion test. However in the large-scale drop hammer test, the amplification of the peak pressure is low compared with in the underwater explosion test. C) The impulse value was independent of the types of the microballoons or microbubbles in both tests. It was concluded that the type of the microballoons or microbubbles significantly influenced the characteristics of the pressure wave propagation in emulsion explosives.

Jan 1, 2001

By Brent Blanchard

The use of explosives to safely fell structures can be traced back over 300 years. Since then, dozens of chemists, inventors, blasters and demolition experts worldwide have played prominent roles in the evolution of what has become the modern-day explosive demolition industry. In America, one of the earliest applications of explosive demolition occurred in response to the great fires of San Francisco, where homes and businesses were blasted with gunpowder in a desperate attempt to create firewalls. Later in the 19th century, inventions such as nitroglycerine, dynamite and blasting caps made structural blasting a safe, efficient alternative to conventional demolition methods. The 20th century brought the first experiments in shaped charge technology, and this, combined with developments in portable seismology and non-electric delay systems, allowed an ever-expanding variety of structures to be explosively felled by demolition experts throughout the country. The 1950s and .60s brought a new wave of commercial structural-blasting entrepreneurs (several of whom are still active today), and their efforts towards improving adjacent-structure protection and public relations beget the felling of large commercial buildings in dense urban environments. By the late 1980s, publicity-driven motives were gaining greater influence in the decision to .implode. various structures, and the transformation of blasting operations into promotional spectator events played a role in several injuries and fatalities. Since that time, however, a renewed sense of responsibility practiced by most blasting firms and project officials has resulted in the safe, successful completion of hundreds of recent endeavors. In sum, what appears today as an efficient, economical - and visually spectacular - way to demolish structures has its roots in developments of the past several centuries

Jan 1, 2002

By Cameron McKenzie

Flyrock is a complex issue involving interaction between the charging crew, the blast design, and the local geology, and once conditions on the shot meet certain criteria, the probability of a flyrock incident becomes unacceptably high. It is essential that flyrock awareness be built into the blast design process, requiring an engineering approach to understanding and controlling the outcomes and managing the associated risks. Based on previous studies of flyrock and published literature relating to fragment motion at high velocity in air, the equations to predict maximum flyrock range, and the size of particle achieving the maximum range, for blasts of varying rock density, hole diameter, explosive density, and state of confinement have been developed. These equations, and other associated correlations, permit the flyrock footprints to be established for any charge configuration, in any size blasthole, in rock of any density, and with particles of any known shape factor. The equations developed, and the mechanisms they reflect, allow engineers to go a long way towards understanding the primary factors controlling flyrock generation, including the rock mass, the blast design, and the quality of blast design implementation, i.e. the human factor. The paper presents guidelines as regards use of the equations to establish personnel clearance distances as a function of charge design and implementation, and equations to estimate appropriate stemming lengths when blasting must be conducted close to occupied or sensitive structures. The equations are amenable to definition of, and quantification of Flyrock Risk.

Jan 1, 2009

By Jonathan Zimmerling, Rob Alkins

The model of waves emanating from a blast hole proposed by Heelan, and further developed by Blair and Minchinton, provides an approximation of particle motion in an isotropic, continuous and homogenous medium caused by a cylindrical pressure source. Previous work in the literature shows that the shapes of the peak strain and peak particle velocity contours generated by this model are influenced by priming location. This paper presents the results of experimental investigations into the effects of priming position in an explosive column and the resulting shape of the surrounding stress and particle velocity fields. Fifteen emulsion charges were detonated in a limestone quarry, of which eight were bottom primed and seven top primed. The charges were fully confined, with no breakout to any surface. Particle velocity was monitored using tri-axial sensors coupled to the rock using cement, and pressure sensors were placed in water filled boreholes for fourteen of the experiments. Statistically significant differences in peak pressure for bottom and top primed shots were observed. Blair and Minchinton developed two pressure source functions, one of which is scaled using the charge weight scaling law. New models of the explosive pressure source are developed and compared to those found in the literature. These models are directly calibrated by predicting the peak velocities achieved at the known locations of the velocity sensors, then minimizing the residual sum of squares between the predicted and observed peak vibration values. Due to the complexity of the model the residual sum of squares cannot be minimized using standard non-linear optimization techniques, so a stochastic, agent based global optimization method is employed. Models are then cross validated by comparing the relative predicted differences in stress between bottom and top priming position to the observed differences.

Jan 1, 2013

By U Nyberg

Peak particle velocity (PPV) and distance measurements from a single-charge blast test conducted by Swedish researchers in iron ore at the Kiruna Mine in northern Sweden are presented. They are used along with theoretical PPVs calculated using an equation based on hydrodynamics to determine a damage distance range caused by a single charge. This equation, which relates PPV to explosive properties, charge geometry, and distance from a charge, was then applied to a charge of different geometry that was used in drift rounds. A comparison between calculated and measured PPVs suggests that the stoping holes likely damage the easer hole locations, and the easer holes produce damage to the perimeter hole locations. The practical effect is that typical damage limit predictions based on measurements conducted in fresh or undamaged rock are conservative. This suggests that even when perimeter control is not exercised in drifting (i.e., the perimeter holes are fully loaded), the resulting damage may be less than normally expected due to the wave damping effect of the pre-damaged rock. Due to the damping effect, poor perimeter blasting practices are somewhat self correcting. However, it must be strongly emphasized that well-engineered blast designs with perimeter control are highly beneficial in relation to both economic and safety aspects.

Jan 1, 2011

Blasting in a development heading or breasting operations starts from a cut. The void created by the cut provides a free face for the remainder of the round. It is the most critical part of the round because the later firing charges cannot pull to the desired depth unless the cut comes out as planned. The Burn cut is most commonly used in Canadian mines.

Jan 1, 1995

By Terry Nichols, Karl E: Warkwick Burgher, Charles J. Wideman

The application of Fourier spectral analysis to records of ground vibration generated by over 100 explosions from an open pit mine is used to develop empirical predictor equations that relate the response spectra to the blasting parameters used to generate the excitation motion. Time series representations of ground particle velocity are transformed into the frequency domain where the appropriate modifications are made such that the inverse Fourier transform yields the time series representation of particle displacement and acceleration. Compensations are made for the transform function of the recording system in the frequency domain. Spectral analysis of the three types of ground motion is correlated with the blasting parameters. The results show that the frequency content of ground vibrations generated from a mine blast can be quantified in terms of the predictor equations.

Jan 1, 1990

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By L. O. Souza, J. F. Gewher, M. P. Scussiatto, C. S. Mendonca, R. A. McClure, B. T. Kuckartz, J. Kloeckner

Blasting is the most effective and economical tool available to fragment and move rock for most applications. If properly executed, it can improve down-stream operations such as loading, hauling and crushing. It is not possible, however, to have full control over the energy released by the explosives when a poorly designed blast pattern is used. A poorly designed blast can produce serious damage to equipment and create a potentially hazardous condition to people. Advanced mining technology has been developed to address these potential hazards and optimize the blast pattern. This profiling technology can assist with blast planning and provide quick, precise data about the condition of the rock structure to be blasted. The 3G BlastMetrix system presented here uses three-dimensional (3D) stereo photogrammetry to model the rock mass in a fast, practical and safe manner. Through the image overlapping method, a 3D model is created with thousands of points that provide a significant amount of data regarding geology, geometry and topography conditions. The blasting plan can then be made in a way to optimize the rock fragmentation and avoid areas that could create flyrock. This paper is a case study concerning usage of stereo photogrammic surveying and borehole survey systems in a blasting operation at the Brazilian Quarry, Incopel. One 3D image of a drilled bench was generated using photogrammetry survey technology and the borehole survey data collected using the rodded Boretrak borehole survey system. Utilizing the minimum burden profile reports, explosive loading could be done accurately, resulting in an optimized blast with good heave and fragmentation as well as increased safety.

Jan 1, 2013

By Brian Stump, D. Craig Pearson

This work quantifies seismic coupling as a function of charge weight for single-fired (simultaneously detonated) explosions observed in the mine and at regional distances. These single-fired explosions are contrasted to standard production shots from the same mine. Production shots include cast blasts to remove overburden and coal shots for fragmentation. The blasts were conducted in a mine in NE Wyoming. The data sets consist of measurements in the mine (100-10,000 m) and at regional distance (360 km) using a seismic array near Pinedale, Wyoming (PDAR). The single-fired explosions ranged in designed size from 5,500 to 50,000 lbs. Peak amplitudes measured at a single element of the regional array are modeled by a power law relation dependent on explosive weight. Scaling constants were determined for each of the dominant regional phases: b(Pn) = 0.84±0.14; b(Pg) = 0.84±0.09; b(Lg) = 0.91±.08. Spectral ratios of observations from different explosions observed at the same station illustrate the frequency dependnce of the source scaling relations. Spectral ratios of in-mine observations are consistent with those of regional data. The observed single-fired ratios are well replicated by Mueller-Murphy source model ratios. The data and model illustrate both the increase in long-period spectral level and the accompanying decrease in source corner frequency with increasing charge weight. The coal and cast blasts that make up the production shots ranged in size from 77,000 to 4,738,230 lbs. The peak amplitude (1-20 Hz) for the largest delay-fired production shot (4,738,230 lbs.) is comparable to that of the largest single-fired explosion (50,000 lbs.). This comparison can be explained in terms of destructive interference between waveforms from individual boreholes introduced by delay firing. Shot specific models of delay firing suggest that peak amplitudes in this same frequency band for the production shots are insensitive to the total amount of explosives in the blast. Peak amplitude data at regional distances supports his modeling result.

Jan 1, 2002

By Michael S. Wieland

This report discusses measurement techniques utilized in and trend results obtained from research on delay blasting malfunctions in underground coal shots at the U.S. Bureau of Mines. Charge malfunctions occur during delay blasting in underground or surface mines, rendering the explosive operations more hazardous and less productive. Modern instrumentation techniques reveal several types of reduced charge performance, resulting from cross-hole interactions. Two receptor (wave-target) charge malfunctions were detected in fourteen shots that were undeniable. There were other receptor charges that exhibited under-performance by registering out-of-tolerance or noticeably reduced detonation rates. Delay blasting generates tremendous shock waves and rifting forces that fracture and heave the surrounding stratum and unfortunately damage remaining unfired charges. This report contains two graphs, representing roughly 1% of total records, that show donor (wave-source) charge shock waves and rift (reaction-to-heave) compressions. These debilitating wave impacts precipitate modes of reduced charge performance ranging from weak detonations or misfires to sympathetic detonations. As recognized from previous research, impaired charges react poorly, perform less useful work, and yield fumes with atypical higher toxicity.

Jan 1, 1995

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

The basic metric for linear shaped charge performance is the amount of cutting distance that the charge can effectively yield given a specific standoff and target. Due to its size and restricted production runs the 10,500 grain/foot (2,232.25 grams/meter) linear shaped charge has had only limited studies that examine cutting performance and standoff. This article covers research regarding cutting performance verses standoff as the charge is applied to common structural steel. Specifically this study uses A36 mild carbon structural steel blocks of 10.16 cm by 11.80 cm by 35.56 cm and standoff distances of 0.5, 1.0, 1.5, and 2.0 charge diameters. Data presented includes the presentation of actual cutting performance numbers, comparison of that data to projected performance based on currently recognized industry guidelines, and a discussion of what may contribute to the performance found in this study.

Jan 1, 2013

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Mark A. Rugen

It may be difficult to imagine but small engineering companies do exist, even in relatively large cities like San Antonio. Due to the limited capital available for the purchase or use of equipment such as computers, many times the small company must evaluate a blast damage claim by limited means. This paper will discuss how a relatively small company has managed to become the leading blast damage experts in an area without the use of computers or sophisticated equipment. It will be shown that a single individual in a company who is familiar with vibration theory, local soil conditions and who does not mind spending long hours with a calculator and reference books can satisfy both the insuranc e adjuster or attorney, and the homeowner concerning the claim. Several examples will be given which show the typical flow of work and the ultimate outcome. This paper will focus on the special problems encountered by a small firm and how these can be overcome, and the unique interaction of a small engineering firm with both the insurance adjuster/attorney and the homowner that can lead to an equitable settlement of the claim.

Jan 1, 1983

By Michael Karmis, Syed Muhammad Tariq, Zeshan Hyder

Secondary or boulders blasting is a regular feature of quarrying operations in Pakistan, especially in cement and stone crushing industries. The main reason for secondary blasting is the production of a large number of boulders during the production blast. These boulders are larger than the feed hopper of crushers and require further breaking. The complex geometry of boulders, relative lack of restraining burdens, and the availability of number of free faces make this kind of blasting more hazardous than production blasting. Secondary blasts have generally unpredictable results and may cause flyrock, airblast, and over-crushing of rock material. Thus, it is essential to have an appropriate amount of explosive charge/powder factor, and for it to be properly distributed in the blast hole. The greater the amount of explosive over the required amount, the more violent is the blast, which will result in more flyrock, airblast, and excessive crushing of boulders.

Jan 1, 2012

By Greg Rappard, Francois Holowenczak, James Rickard

The King George V (KGV) Shaft forms part of MTR Corporation Limited (MTRCL) Works Contract 703 extension of the underground West Island Line on Hong Kong Island. The Shaft and the associated adit was the sole access to excavate the running tunnels. Originally during the Detailed Design stage, it was concluded that blasting was not feasible at the KGV Shaft due to the close proximity of sensitive receivers in the form of residential buildings, electrical cables and hospitals. As a result, the Contractor planned to excavate the Shaft using mechanical means with a programme time of seven months. The Contractor appointed a Sub-contractor to analyse the feasibility of excavating the Shaft by blasting. The Sub-contractor reviewed the proposal and recommended the use of an innovative blasting technique that had never been previously employed in Hong Kong. The Sub-contractor recommended the Shaft be blasted using DetNet electronic delay detonator technology, manufactured by AEL Mining Services in South Africa, with an initial 1.5m depth of water ballast covering the blast face. The electronic delay detonators provided initiation accuracy to ensure there would be no overlap between sequentially detonating blastholes. The water ballast makes use of the effect of energy lost through the shock front causing the water to break up into droplets creating a spray dome resulting in the attenuation of the energy imparted into the surrounding rock mass. Various tests have demonstrated that both the maximum overpressure and impulse density are significantly reduced when water of a minimum depth is in direct contact with detonating explosives. This innovative blasting technique reduced the excavation programme by three months, saved HK$5 million in direct costs and totally mitigated the impacts on the public and other stakeholders nearby the KGV Shaft. Peak Particle Velocities (vibrations) rarely exceeded 2-3mm/sec (0.08-0.12in/sec) at a distance of 30-40m (98-131ft) from the blast location and air overpressure levels were reduced below the Hong Kong target level of 120dBL. In total, 24 blasts were fired with an average advance of 1.6m (5.25ft) with an average powder factor of 2.03kg/m3 (0.127lb/ft3) to 1.84 kg/m3 (0.114lb/ft3). The initiation pattern had 5ms between sequentially detonating blastholes and 20ms between adjoining rings.

Jan 1, 2013

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020