Search Documents

By R. F. Bell, Schultz

The paper briefly discusses the nature of spontaneous heating in mines in the Doncaster area, in the period immediately before 1967 and steps taken to prevent and treat such outbreaks. The changes that led to the increased rates of advice of Barnsley Seam faces since 1967 are listed and the effects of these increased rates on the frequency and location of spontaneous combustion are discussed. The change in methods of control required by the increased rate of advance of the faces and the changes in location of outbreaks are described. Some typical heating situations are evaluated. The methods described include the use of air sealants, water gels for filling of voids in wastes, the balancing of pressures across heating areas by pressure chambers, booster fans, and the resiting of air separation doors, and the sealing of air-ways by flooding. The authors discuss the influence of mine layouts on the risks of spontaneous combustion and advocate that future plans should be designed to limit the number of districts at risk when heatings occur.

May 23, 1905

By R. R. Liebenberg, M. I. Brittan

The kinetics of the copper segregation process has been investigated. The experimental strategy used to isolate the rate-controlling reaction step is described. This step was found to be the chloridisation of the oxide copper minerals in the ore. The link between the rate of chloridisation and the overall rate of segregation is demonstrated experimentally. The influence on the kinetics of the various parameters in a TORCO system is examined and the implications are discussed

Dec 1, 1971

By R. N. Pryor, S. H. Shaw, D. L. Dowie, S. H. U. Bowie, M. J. Cahalan, S. F. Gandar

It is concluded that land-based mineral resources will be adequate for most minerals in the immediate future, but in the long term more minerals will come from offshore locations. Because the oceans are international and can transport pollution, international control of offshore workings will be necessary. In the UK and similarly highly developed areas, the working of low-value bulk minerals will create increasing problems in urban development and countryside preservation. Much more information should be published on standards to be adopted and their costs, if emotional social pressures founded on ignorance are to be avoided. The Town and Country Planning Acts have greatly improved the environmental quality in Britain in relation to mineral working. In the long term conservation of some minerals in short supply may be necessary on a national or international basis. Much research is required for the determination of adequate criteria and standards for the preservation of environmental quality in the mineral industry. New local, national and international legislation will be required and the adoption of voluntary standards by trade associations should be encouraged wherever appropriate

Dec 1, 1971

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

By E. L. Evans

The historical development of South Yorkshire mining is traced and note made of the liability to generate spontaneous combustion of some of the seams which have been worked. The liability factor is analysed firstly as an inherent property in the material of a coal seam, and secondly as a circumstance of a situation in which access is provided for the air necessary to sustain oxidation. The geological settings in which incidents of heatings have been known to occur is discussed and conditions favouring a natural pre-disposition to spontaneous oxidation exposed, particularly the effect of argillaceous material overlying the seam. An extensive strata-dynamic study follows to demonstrate the situations in which stray air currents tend to impinge on readily oxidizable material. Prevention techniques are indicated as the identification of strata-dynamic situations in which air access to broken coal is induced and thereafter th operational action to seal off the voids which have been opened up so as to exclude air from the broken coal. Measures to reduce the tendency for ventilating air to short circuit across waste voids, and to obviate deflection of air into packs are outlined. The importance of face and roadway design features is demonstrated and the consequences of practices inimical to good control of spontaneous combustion are related. Discussions on means of detection and also on the sealant materials available are included.

May 23, 1905

By Mohammed Ali Shah, Martin Waller

The mining industry depends to a large extent on the availability of high performance equipment. For drilling this means a requirement for well engineered, reliable machines with mechanised handling and widespread utilisation of automatic control. Such machines enable performance optimisation of drilling operations and integration into a high productivity mining system. A review is presented of the current status of drilling technology as applied to the mining and minerals industry. This covers developments in: drill bit materials and design; drilling techniques; machine design; mechanisation; automation; and drilling control. It also covers the ways in which current and future mining methods and practices will influence the applications and demands placed on drilling activities. The probable impact of current research on the industry is discussed.

Jan 12, 1992

By G. B. Hooper, G. A. Ferguson

The technical capabilities and user-friendliness of the major computer-aided mining design software systems are reviewed. Recent experiences with three systems are outlined to indicate the practical problems that arise. The examples were: Microlynx software from Lynx Geosystems at the Great Dyke platinum mine in Zimbabwe; Lynx software from Lynx Geosystems at a copper mine in central Africa; and PC-MINE software from Gemcom Services at an open-pit gold project in Western Australia. Difficulties in the use of mining design software has led to an alternative approach. Falconbridge, Canada, has developed an integrated mine-planning system on a CAD platform that encompasses ore reserve estimation, stope design, development layout and survey control. Future directions of computer-aided mining design using this basis are discussed. A major advantage of using mainstream software packages, such as spreadsheets, databases and CAD programs, is that most engineers and geologists are experienced in handling such systems in the normal course of their work.

Jan 12, 1992

Thermodynamical data of importance in connection with copper smelting have been reviewed and a collection of the most reliable information is presented in Tables XXV-XXVIII and Figs. 67 and 6 8 (folding plate). The data given in these figures and tables consists of (i) graphs and equations showing the variations in the temperature range 0-2000°C. of the standard free energies of formation of most of the oxides and sulphides met with in copper smelting (Table XXV and Fig. 67); (ii) equations showing the temperature variation of the free energy of formation of iron silicates (Table XXVI); (iii) graphs showing the variation with temperature in the range 1000°-1600°C. of the standard free energies of the principal reactions occurring in the smelter (Fig. 6 8 ); (iv) the standard heats of formation at 1200°C. of the main iron and copper compounds and gases reacting in the smelter (Table XXVII); (v) the standard heats of reaction at 1200°C. of a few of the reactions for which the free energy relationships were given in Fig. 6 8 (Table XXVIII). The data presented are discussed in more detail.

Jan 1, 1953

By J. Coxon, G. W. Walker

The paper describes the discovery, location and events concerning three types of heating which have occurred in recent years: a) in a district being salvaged, b) in the shaft pillar at an air-crossing, and c) in the gate side of a production district, all of which have occurred in the Beeston Seam at collieries in the deeper eastern part of the area. The paper describes the precautions, air sampling arrangements, training methods and codes of practice which have been adopted at collieries where spontaneous combustion is, or is likely to be, a hazard. The air samples taken from behind the stoppings following the sealing off of the salvaging district are examined and interpreted. The problem of effectively sealing off where more than two stoppings are required is made apparent. Other lessons have been learned as a result of these heatings and are described in the paper.

May 23, 1905

By M. W. Davies, P. N. Smith

The activity of MnO has been measured in the system CaF2-MnO at 1773 and 1873 K and in the system CaF2-CaO-MnO at 1773 K by the method of equilibration with platinum. Large positive deviations from ideal solution laws have been found, but these became less as the lime content rose. The loss of a volatile component made activity measurements impossible in the CaF2-AI203-MnO system, but the boundaries of a two-liquid region have been measured at 1773 K.

Dec 1, 1971

By J. Cech

Discussion is presented of a decision-making support method for the spacing of ore passes along a long vein orebody and the division of the orebody into convenient stopes for future mining operations. The method was tested on a Slovak siderite deposit and also on some hypothetical cases with the objective of obtaining more general results

Jun 18, 1905

By Fearnsides W. G.

The map shows the sites of collieries and important boreholes in the district, with approximate underground contours of the pre-Permian surface of the Coal-Measures and of the Barnsley Bed

Dec 1, 1916

By T. F. Bamber

The South Nottinghamshire Area has not been greatly troubled by spontaneous combustion until the last few years, during which the Blackshale Seam has been developed and exploited. The problem was first encountered at a colliery which was heavily preoccupied with a major reconstruction scheme, and with the sudden appearance of a completely new hazard both men and management had to adapt themselves very quickly to meet the situation. The paper contributed to the Symposium by the South Nottinghamshire Area illustrates the problems by reference to actual incidents, and shows how the lessons learned from them have been applied to the shaping of future policy on the avoidance and treatment of spontaneous combustion.

May 23, 1905

By Winmill T. F.

Among the various theories proposed to account for the spontaneous ignjtion of coal, one which has at times been very strongly held is that the initial heating is due to the oxidation of iron pyrites. From the results described in this paper, it is possible to calculate roughly the rate of spontaneous heating of a specimen of finely-divided pyrites, on the assumption that all the heat developed is used in raising the temperature of the pyrites, and that none is lost. It is clear that where finely-divided pyrites occurs in considerable proportion among coal, it may be the chief factor in originating combustion, but that pyrites can only be the cause of a heating when it is present in considerable proportion, and in a very finely-divided state

Dec 1, 1916

By S. V. Shiraishi, H. B. Bell

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J. Cahalan, President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, June, 1970, pp. C120-C127, with a contribution by Wright P.A. on the miscibility gap

Dec 1, 1971

By E. A. C. Chamberlain

New techniques for the continuous sampling and analysis of mine air are expected to replace traditional methods used for the early detection of spontaneous combustion. It has been established that the rate of evolution of carbon monoxide is the earliest indicator of incipient spontaneous combustion. Two methods of continuous monitoring of this gas are available and are now in use in the UK collieries. The first is the UNOR infra-red gas analyser, which is flameproof and may be used underground; the second is a system of tube bundles, which permits air to be drawn from any critical point in a colliery and analysed on the surface. Each system has its advantages and disadvantages but both provide the colliery manager with far more information on the condition of his pit than could previously be obtained by spot sampling and laboratory analysis. This paper describes the two systems presently in use and assesses likely future developments.

May 23, 1905

By B. Sonmez, B. Aksanl, S. Ersaym, I. F. Erkal, S. L. Ergun

The comminution circuit at the plant has experienced severe problems arising from a feed containing much larger amounts of clay and having a higher moisture content than expected. Three solutions were proposed: replacement of the crushing circuit by tooth roll-type crushers; using washing drums; and introducing primary autogenous/semi-autogenous millling instead of crushing. Computer simulations studied the effects of the first two solutions on the circuit capacity. Laboratory and industrial scale ball mill batch grinding tests were carried out. The parameters of a kinetic model were determined. The ball mill circuit was sampled and operating model parameters were calculated. The ability of batch grinding parameters to represent the operating conditions was studied. Tests failed to find acceptable model parameters, but parameters from an industrial size batch mill were found to be suitable for simulation studies. The simulations indicated that a continuous feed of -12 mm provided by tooth roll crushers would maintain the desired capacity. Increasing the feed size to -25 mm would reduce the capacity by 8-15%. The use of washing drums could also solve the capacity problem, but small fluctuations in water flow rates might result in problems of excess water in the grinding circuit.

Jan 4, 1993

By A. Ludkin

The paper presents the history of the occurrence of spontaneous combustion in the north area, together with the associated problems. These are examined and a description is given of the methods used to combat the danger, including the use of modern scientific instrumentation. Detailed reference is made to the underground trials with pack injection and sealant coatings which were carried out at Seafield Colliery following the formation of a working group to assess the performance, in the same underground conditions, of (1) sandbagging, (2) pack injection, (3) surface coating. Based on these trials, an improved and more economical method of prevention has been established. There is, however, still scope for further improvement in techniques which would take into account the problems of gradient, transport, manpower and cost.

May 23, 1905

By NA NA

Listing safety award winners, £I43M has been added to proceeds from coal privatisation in the year to March 1997, bringing total revenues to over £1.3bn, some company news in brief.

Jan 8, 1997

By G. D. Nicholls

There have been very few attempts to isolate the various factors that contribute to the overall imprecision of geochemical analytical procedures, due in part to the difficulty of distinguishing between them. The technique of spark source mass spectrography permits a ready distinction between the contributions to overall precision from sampling error and instrumental and other errors. With conventional methods of sample preparation for this technique sampling difficulties are responsible for 80-90 per cent of the overall imprecision. Examination of the probable location of the major difficulties in sample preparation indicates that the preliminary stage of grinding, mixing and extraction of a first aliquot (about 1/100 of the original sample) is generally perfectly adequate. The difficulty lies in the subsequent stages of sample preparation. Dry mixing techniques are unlikely to give good precision if the sub-samples actually examined by the analytical technique are less than 10 mg in amount. Solution techniques are less prone to sampling difficulty. Fusion techniques, unless conducted with great care, can produce more difficulty than dry mixing. Sample preparation is critical to the success of many analytical procedures. Selection of appropriate sample preparation techniques requires just as much care as the selection of techniques for the actual analysis.

Dec 1, 1971