Search Documents

By M. Salas, L. Rolf, H. Z. Kuyumcu

"Industrial use of abrasive stress takes place in the area of fine grinding and in order to clean surface contaminated soil particles. Also, at many mechanical operations abrasion emerge as an unintended side effect. At the Institute for Raw and Waste Material Processing at the Technical University of Berlin systematic investigations are carried out, to further the knowledge regarding the dependence of abrasion process on material properties and stress mechanisms as a basis for design and optimisation of the process or for its avoidance. Aim was the mathematical description of the abrasion process running with a single particle stress. For the purpose of investigations an agitation cell was used. Limestone served as material.In the presented work the influence of particle diameter, particle shape and collision energy on the mass and particle size distribution of abrasion debris was studied. The surface geometry of the particle was characterised by the particle shape factor ?x and the particle diameter dp. The particle shape factor ?x stays in direct relation with the abrasion degree x, and can be substituted by a mathematical function of x.Physically the particle shape factor ?x can be interpreted as a proportion of abrasive stresses splitting up complete crystals and crystal fragments. These two different mechanisms depend on different ratios of curvature of the surface of the stressed particle. The abrasive stress of strongly curved surface areas leads to separation of complete crystals. The abrasive stress of weakly curved surface areas leads to separation of crystals fragments. Accordingly the mass of wear mAb and median diameter of the abrasion debris d50 are different. The derived mathematical relations consider this behaviour by the particle shape factor ?x , which represents the ratio of the mixture of both stress mechanisms. The dependence of the particle shape factor ?x on the abrasion degree x with an exponent approximately to 2/3 points out that the particle shape factor ?x represents a surface area relation."

Jan 1, 2003

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Industrial minerals may contain the same elements in approximately the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques.• quantitative measurements by ebsdCommon automatic techniques describing the mineral contents and the occurrence of minerals in free and locked particles, are based on optical-, backscattered electron (BSE)- or X-ray-signals. There are various commercial software systems on feature analysis by backscattered and X-ray signals in combination with image analysis (e.g. Oxford Inca Feature, CSIRO QemScan).Especially in silicates, the occurrence of similar elements in the different minerals is common. Sometimes the various minerals not only contain the same elements, but also approximately the same amount of each element. In these cases BSE imaging and chemical analysis are not always sufficient for identification."

Jan 1, 2003

By J. Faitli, I. Tarján

One of the basic processes of process engineering is the production of dense suspensions. The major two equipment of this task are the periodically operating propeller mixer, and the continuously operating mixer tank based on the flow principle. In the laboratory of the Department of Process Engineering at the University of Miskolc, laboratory scale experimental setups had been built of both types of mixers in the frame of the FKFP 0504/1999 signed research project, supported by the Hungarian Ministry of Education. By these experimental setups many systematical experimental series had been carried out by test materials of water as the dispersing media and sand, power plant fly ash and magnetite as the granular solids. On the basis of the literature and these experimental investigations, scale-up methods had been developed for both types of mixers for the determination of the main technical parameters of industrial size equipment.

Jan 1, 2003

By G. Onal, E. Gock, H. Dincer

"During the conventional chromite dissolution process; chromite ore concentrates were ground to at least <90 µm using the ball mill and after adding Na2CO3 and leaning material (instead of CaCO3 also residues from the leaching process) at a ratio of e.g. 1:0.75:1.2, depending on the specific formulation, follows the digestion e.g. in a rotary kiln, heated in countercurrent. The reaction time is 3 to 8 h. The calcine is comminuted and leached with water or a thin chromate solution. Depending on the type of ore used, the yield is 75-85 %. The disadvantage of the above-described process is that it is impossible, using current technology, to achieve a complete digestion of the chromite ores and that the chromium-containing residues have to be disposed of as special waste, involving a large financial effort.The subject of this study was the investigation of the effect of vibratory milling on chromite dissolution. The impact stress in the vibratory mill causes the mechanical activation of chromite, which is characterised by lattice defects. The degree of mechanical activation can be quantified by measuring the relative X-ray diffraction intensities at the parent lattice planes of chromite. Each relative X-ray diffraction ratio correlates with a certain degree of digestion. As opposed to vibratory milling, a complete digestion of chromite using a ball mill is impossible, even at extremely long grinding times.In this investigation a chromite concentrate from Pulpinar/Kayseri with content of 44 % Cr2O3 and the Eccentric Vibratory Mill was used. In order to verify the effect of the vibrating grinding on chromite dissolution, reaction kinetic investigations on digestion and leaching were carried out."

Jan 1, 2003

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Only grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own.CONCLUSION• Overflow versus grate dischargeAn overflow mill has a “pool” of slurry around the toe of the ball charge, which creates a counter lever to the ball charge. This will reduce the absorbed power in the range of 10-15% (depending on the case) and will consequently result in a coarser grind. The tests found a 4% gain in grinding efficiency (Wio) with an overflow mill but this is probably not significant.This lower absorbed power and coarser grind can be counteracted by increasing the ball charge (if below maximum) and/or by increasing the mill volume when removing the grate discharge (a typical grate takes up about 300mm of the mill length).• Open versus closed circuit"

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Abel Bissombolo

"In flotation practice, a good recovery of minerals largely depends on the degree to which the valuable minerals have been liberated from the associated gangue during the grinding process. Therefore, a regular measurement of the degree of liberation can provide data for the assessment of the quality of separation and predicts the effect of changes in the grinding-classifying circuit on flotation process. Generally, the standard procedure for measuring the degree of liberation requires the preparation of polished sections - a time consuming operation that also has the disadvantage of providing an overestimated number of free particles because of the stereological nature of produced samples.The present work is an alternative approach to avoid these miscalculations and establish a system of control for fluorite flotation plants. The system deals no only with the state of liberation but also the dynamic behavior of individuals particles and mineral components within the grinding-classifying and flotation circuits. It involves methods such as sieving, x-ray diffraction analysis, study of polished sections and microscopic counting of preliminarily sieved minerals particles from a fluorite processing plant, randomly dispersed on a glass slide, but not embedded in a resin mounting medium. If a complete information on the textural properties of minerals in the ore (including its mineral components distribution) can be obtained through x-ray diffraction analysis and study of polished sections, the microscopic counting is used to determinate with enough accuracy the mineral liberation, estimate the grade of fluorite ore and products, determinate the deportment and approximate recovery of individuals particles and mineral components within the investigated circuit. For a count of 100-1000 particles in each n-size range, the counting method was found to be a particularly reliable and less time consuming operation that could substitute the chemical analysis of fluorite ore for an estimate of the grade:"

Jan 1, 2003

By Gi-Chun Han, Ki-Suk Han, Korea Energy Management Corp., Jin-Sang Cho, Hyung-Seok Kim, Jae-Hyun Oh

This study has been carried out to use the waste sludges generated at Pohang Iron & Steel Co. Ltd. (POSCO) as the raw materials of Ordinary Portland Cement (OPC). The burnability index of the raw mixture and the hydration characteristics and compressive strength of clinker have been examined. The waste sludges were mainly composed of CaO, SiO2, Al2O3, and Fe2O3, the main component of OPC. The Burnability index of mixture was improved, according to the replacement content of POSCO sludge increase. POSCO sludge can be used as a raw material for cement because the state of mineral development and property of clinker produced from POSCO sludge are similar to the plain. Therefore, POSCO sludges can be used as the source materials of iron and calcium oxide.

Jan 1, 2003

By M. Brozek, W. Pawlos

"The separation of raw materials in the separator with ferromagnetic liquid occurs due to differences in magnetic and gravitational properties of respective components in relation to each other and to the liquid. In the separator with wedge-shaped pole shoes and the working space axis inclined at a certain angle to the horizontal direction, the paths of grain movement at fixed separation conditions depend on its physical properties. Due to this, the levels of grains outlet from the separator working space are differentiated according to differences in their physical properties. The distance between the levels of outlets from the separator working chamber depends on magnetization of the liquid which is proportional to the liquid density, on the magnetic field intensity and the inclination angle of the separator working passage to the horizontal axis. The separation accuracy is higher the larger is the distance between the outlet levels.The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid which was the water solution of manganese chloride. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images. Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement by a numerical method, achieving good compatibility of experimental and theoretical results. The equations of movement were solved with taking into consideration the drag force, expressed by formula for laminar and dynamic conditions of motion.The course of the path of grain movement depends on grain and liquid physical properties, magnetic field intensity and inclination angle of the working space to the horizontal direction. The two latter parameters can continuously control the process of separation."

Jan 1, 2003

By A. F. Raschenko, Y. A. Golodcov, V. V. Elshin

"The autoclave noble metal desorption in apparatuses with a dense stationary sorbent layer is perspective for the technology of sorption gold and silver extraction from solutions and pulps by carbon sorbents. The study of the mechanism and optimization of the autoclave desorption process involve some difficulties. To overcome them it is necessary to use mathematical and quantum-chemical modelling. The given paper deals with a mathematical model for the dynamics of gold and silver desorption from active carbons by alkali solutions based on the physical-chemical notions of the process. The kinetics and the mechanism of the process were investigated using the mathematical model for gold and silver desorption.The calculation of the efficient mass-transfer coefficient (ße) for various initial and intermediate noble metal concentrations in carbon (Cy) made it possible to find that the dependence of ße on Cy in case of gold desoprtion shows a clear extreme character. The value of the initial metal concentration in carbon therewith does not influence the character of the curve the inflection point of which is changed essentially at elevated process temperatures only. The revealed characteristic property, in the author's opinion can only be indicative of the change in the mechanism of gold desorption under autoclave desorption conditions. The assumed [Au(CN)(OH)]- type intermediate that has a higher diffusion coefficient in comparison with the adsorbed complex [Au(CN)2]- can be considered as an intermediate compound in the process of gold desorption."

Jan 1, 2003

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture. These equations are called geometric probability equations.Davy derived a geometric probability equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. This covariance can be used to measure the variance of the particle composition distribution of each mineral. The equation as presented by Davy requires textural information; however the equation was modified by Gay to be more directly applied to particle sections and linear intercepts. The variance obtained from applying this equation is fundamental to the binary stereological correction procedures developed by Gay and his colleagues; the covariance is fundamental to the multiphase stereological correction.Thus far, validation of both the binary and multiphase stereological correction has been achieved using numerical simulation. This paper shall present results comparing the covariance (and variance) estimates from Gay’s equation with actual three-dimensional information obtained from serially sectioning particles. This involved mounting a set of particles and continuously sectioning all particles uniformly so that the three dimensional structure of the particles could be obtained.The mineralogical data to which the equations described above were applied were derived from two individual size fractions from a hard-rock titanium deposit. The deposit contains a range of minerals and of mineral textures and the two size fractions selected were:"

Jan 1, 2003

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management."

Jan 1, 2003

By L. A. Vaisberg

"Crushing and grinding are the two most common industrial processes. These processes consume nearly 20 per cent of the entire electric power produced worldwide. This enormous amount of electric power consumed results from the fact that modern crushing and grinding machines employ the processes first introduced by the prehistoric man, namely those of compression, impact, attrition, and cutting. The material thus handled decomposes indiscriminately, and almost completely ignoring the microscopic cracks and other defects of its structure. Apart from the irrational use of the power, the crushing and grinding processes currently in use result in irretrievable loss of useful components or else in a substantial deterioration of the final products obtained, all as a result of incomplete grinding or, reversely, of overgrinding, palletizing, or fracture of particles.The principal type of equipment that has almost universally been used all over the world for more than 150 years for crushing both natural and synthetic minerals comprises unbalanced jaw and cone crushers. The driving element of crushing bodies in these machines is an unbalanced weight, which transfers the crushing body, allowing it to squeeze the material within the eccentricity value only. The maximum reduction ratio achieved by such a drive is 5, which is due to the rigid kinematic arrangement of the crusher, its dynamic unbalance, and the impossibility of increasing the number of impacts on the material being crushed. Moreover, conventional machines cannot cope with super hard materials, and their mechanism is vulnerable to damage by uncrushable objects.On the basis of fundamental research into the theories of solid body and vibration, OAO Mekhanobr- Tekhnika have developed a range of vibrating jaw and cone inertia crushers that make a reduction ratio of 30 feasible in an open-circuit operation with the reduction ratio monitored within a wide range. In these crushers, the eccentric drive is replaced with a vibrating one. In this way the rigid kinematic drive became dynamic, thus allowing pieces of material to be crushed in a thick layer due to the effect of their bumping into each other, and with the amplitude changing automatically. This results in a number of advantages as compared with conventional crushers:"

Jan 1, 2003

By Rogerio C. Guimarães, Antonio E. C. Peres

The production of phosphate concentrates (phosphate rock) from slimes represents a challenge to the phosphate industry worldwide. In Brazil, this challenge is particularly relevant due to the consistently low P2O5 grades and the igneous origin. The Brazilian phosphate deposits are made up mainly of apatite from alkaline chimneys, representing 80% of the Brazilian reserves; phosphorite deposits contribute 18% and the other sources (guano, phosphorous bauxite, and apatite from veins) reach 2%. The Brazilian industry beneficiates phosphate ores that are mineralogically more complex than those treated elsewhere. The low apatite grade, inherent to the igneous Brazilian ores, added to the mineralogical complexity due to the weathering of the rocks, has represented a permanent challenge to the Brazilian process engineers. The total measured, indicated and inferred reserves reach 3.2 million tonnes of ore with average grade 11% P2O5. The development of local technology for phosphate beneficiation started in the 1960’s. The first industrial experiences of producing phosphate rock from slimes (-44µm or -325#) fraction started at Arafertil, currently Bunge Fertilizantes SA, in Araxá, in the 1980’s. This production corresponds, nowadays, to 35% of the total production of concentrates in the company (830,000t/year) in a circuit consisting of desliming in 40mm microcyclones and concentration in flotation columns, corn starch and fatty acids being utilised as reagents. The performance of slimes flotation and the process control, at Bunge´s concentrator, were improved after the introduction of column flotation technology, in the first half of the nineties. The column flotation technology for slimes recovery was expanded to other Brazilian concentrators still in the nineties: Ultrafértil (Catalão – GO), Bunge (Cajati – SP), Fosfértil (Tapira – MG) and Copebrás (Catalão – GO). At present the Brazilian production of phosphate rock is approximately 4.5Mt/year, with a strong trend for a market increase. Genuinely Brazilian technology is utilised for the processing of slimes, the concentrates representing 11 to 13% of the overall production. The production of apatite concentrates from slimes was relevant to increase phosphate recovery and reduce costs, contributing to the growth of the fertilisers industry.

Jan 1, 2003

By N. Raeis Hosseiny, S. H. Bassir

"Chador-Malu iron ore is one of the most important iron mines of Iran.About 98 percent of Fe in the ore is in shape of Magnetite, Hematite, Martite, aqua oxide of Iron and the other irons are with ferrous silicates, actinolite, cholorite and ferrous dolomites. 1% of Fe has replaced in pyrite. The phosphor distribution in the ore is non-hemogenous and its average in the whole of the deposit is 94%. It is in shape of Apatite.This mine contains considerable phosphor, which makes it useless for metallurgical uses. At this mine the phosphor is reduced in the iron ore at two steps. At the first step, magnetic part of the ore is separated from the gangues and phosphors by magnetic separator. At the second step, the ore is enriched by the flotation methods. Experimental flotation methods to obtain the optimum conditions are as follows:• Effect of Starch as Hematite depressant with ATRAC as Apatite collector• Effect of Sodium silicate as Hematite depressant with ATRAC as Apatite collector• Effect of ASAM as Apatite collector with Sodium silicate as Hematite depressant• Effect of ATRAC (BEROL) as Apatite collector with Sodium silicate as Hematite depressant• Effect of ASAM & ATRAC mixture as Apatite collector with Sodium silicate as Hematite depressant• Effect of Kcarbonate as pH-modifier• Final test to Optimize pH, Collector, DepressantAt this research we have found the optimum circumstance of the flotation of Chador-Malu iron ore in order to decreasing phosphors of iron oxide and floating of Apatite to make pure Hematite.To reach the optimum conditions, some tests were done with different amounts of pH, collector and depressant. The results are as follows:"

Jan 1, 2003

By Jochen Petersen, David G. Dixon

"Although heap leaching may be perceived as a somewhat low-tech route for the extraction of low-grade minerals, the underlying physical, chemical and biological processes are in fact extremely complex. There has been increased interest in heap leaching of sulphide minerals in recent years with the advent of controlled bio-heap leaching, and the need to mine more marginal ore deposits.A detailed investigation into the dynamics of heap leach processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool, HeapSim. Some of the sub-processes that are modelled include mineral kinetics, particle size effects, bacterial growth, oxidation and adsorption, gas adsorption, pore diffusion, bulk advection, gas balance and heat conservation. The interplay of these various sub-processes is illustrated in the paper.Two case studies are presented which illustrate specific features of the model for different applications and how these have helped to identify key areas of concern. The first is focussed on chalcocite heap bioleaching, which shows that by nature of the reaction the process is strongly dependent on the initial supply of acid to the mineral site. In heaps this acid supply can be severely limited by the rate of diffusion from channels of flowing solution into stagnant zones of the heap, whereas in narrow-bore laboratory columns this effect is not observed."

Jan 1, 2003

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:• flotation tailings of crystalline graphite minerals• outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers."

Jan 1, 2003

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the postgrinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances and allowing a more precise mill sizing. Therefore we surrounded the grinding crucible of the Hardgrove mill with a crucible furnace to heat it. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids (water and alkali) with different temperatures. The required heating power is 2000 W. In the implemented equipment we installed four 230V/500W electric heating wires made from heat-resistant alloyed material and surrounded by ceramic insulators. The temperature and temperature-gradient are measured by four PT100 platinum thermal resistors. The data acquisition and control program written in the C language in the Lab Windows CVI program environment measures the voltage proportional to the temperature. Determining the grindability indices of hungarian and greek bauxites experimentally, first dry grinding tests were carried out under standard conditions. During wet and alkaline grinding, to 50 g of dry bauxite 85.5 g of industrial alkali with a concentration of about 200 g/l was added. As grinding aid 2 g of CaO (4 % of dry bauxite) was dosed. From the data it can be concluded: - The tested bauxites show a similar behaviour against temperature change. However, the extent of grindability change is different for different bauxites. - Soft Hungarian boehmitic bauxite can be ground in a high-temperature alkaline medium better than hard Greek one. The increase of grindability according to the high-temperature Hardgrove indices: (kHT = Dry o HT,alkaline H /H ): for hard Greek and soft Hungarian boehmitic bauxites: kHT = 1.7 and 2.4 respectively; according to estimated Bond indices (kB,HT =Wi,dry/Wi,HT, alkaline ): kB,HT = 1.6 and 2.1. - The increase of grindability is the most important factor the reaction of kaolinite with caustic liquor and lime and the loosing of the textural structure at 80 ºC and especially at 100 ºC.

Jan 1, 2003

By ?. ?. Zimin, B. A. Kutlin, X. Baddamsuren

"The ore features of Mongolian fluorspar deposits are shown in the paper. The possibilities of the technological of ore processing on the Bor-Undur combine scheme improvement are analyzed there. Some recommendations are done for scheme development: spare output technologies, the usage large-sized ore separation, flotation by columnar flotation cells, leaching and concentrate agglomeration.New evaluation and usage of mineral sources approach was developed for Mongolian fluoride ores. The conception allows using maximally available mineral resources for getting of metallurgical and acid fluoride concentrates while mining and technological processes: mining (as well as quarrying) -storing, blending-crushing, grinding-combined processing methods-metallurgical using preparation It has been established mining and processing technological schemes should include:• spare blasting technologies providing minimum effect on fluorite crystals which follows ore selective excavation;• large-sized ore separation methods resulted in maximum recovery for these operations in respect to metallurgical fluorite concentrates;• grinding and flotation regimes providing high-quality flotation concentrates getting for their usein chemical industry;• fluorite concentrates agglomeration technologies for providing ability of their use in metallurgical and cement industriesThe results of industrial usage of jugging machines, columnar and pneumomechanical flotation machines for fluospar dressing.The technological approaches implementation in “Bor-Undur” plant maintenance within 1993-2002 years leaded to:• change plant status from just flotation one to gravitational-flotation characterized by technological process stages which are traditional for metallurgical industry and plant capacity increase from 400 to 600 thousand tones of treatment ore as well as concentrate production increase from 120 to 150-170 thousand tones including 120-140 thousand tones of acid grade concentrates with 97% CaF2 ."

Jan 1, 2003

Incomplete liberation of mineral particles is one of the key factors limiting the performance of industrial flotation circuits. This work aims to quantify the relationship between different breakage modes and how these affect mineral liberation properties. A copper porphyry (bornite) ore sample was subjected to breakage using a piston-die compression unit and an impact mill. The particles produced as a result of each mode of breakage were then characterised using Mineral Liberation Analysis (MLA) to quantify the mineralogical and liberation properties of the progeny particles. The impact mill was found to produce bornite that was finer grained relative to the host particles. In con-trast, bornite discharged from the piston-die unit closely followed the size distribution of the host particles and was retained to a greater extent in the larger/intermediate size fractions. The results provide insight into what breakage methods are optimal for the purposes of downstream separation.

Jan 1, 2014