Search Documents

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By D. M. Milovic

On the basis of relatively large number of field load tests of piles, the determination of the ultimate bearing capacity have been studied. Using the load settlement curves and the results of the cone or standard penetrat­ion tests, the ultimate bearing capacity was determined by Van der Veen?s, Mazurkiewicz?s and bilinear approximation method. Also, the evaluation of the modulus of deformation and the unit skin friction has been discussed.

Jan 1, 2010

By Jon Sinnreich

Ensuring the accuracy of collected data during deep foundation static load tests is of paramount importance. Typically, pile head displacements are measured relative to a purpose-built reference system, which is assumed to be fixed. This study presents a simplified error analysis of this assumption, illustrates the potential magnitude of these errors, and proposes an improved method of pile head displacement monitoring.

Jan 1, 2009

By Thomas L. Vande Voort

The strategic plan for bridge engineering issued by AASHTO in 2005 identified extending the service life and optimizing structural systems of bridges in the United States as two grand challenges in bridge engineering, with the objective of producing safer bridges that have a minimum service life of 75 years and reduced maintenance cost. Material deterioration was identified as one of the primary challenges to achieving the objective of extended life. In substructural applications (e.g., deep foundations), construction materials such as timber, steel, and concrete are subjected to deterioration due to environmental impacts. Using innovative and new materials for foundation applications makes the AASHTO objective of 75 years service life achievable. Ultra High Performance Concrete (UHPC) with compressive strength of 26,000 psi (180 MPa) and excellent durability has been used in superstructural applications but not in geotechnical and substructural applications. This paper explores the possibility of using precast, prestressed UHPC piles in future bridges. An H-shaped UHPC section, which is 10-in. (250-mm) deep with weight similar to that of an HP10×57 steel pile, was designed for constructability and economical reasons. Instrumented UHPC elements were cast to conduct large-scale field tests. In the field, two UHPC piles have been successfully driven in glacial till clay soil and load tested vertically. Test results, durability, drivability, and other material advantages over normal concrete and steel indicate that UHPC piles are a viable alternative to extend the life of bridge structures.

Jan 1, 2008

By Alexander B. Reeb, Richard J. Varuso, George M. Filz, Jehu B. Johnson

"T-walls, which are concrete floodwalls in an inverted “T” shape, are an integral component of the Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS). In order to resist large lateral flood loads, T-walls are typically supported on long batter piles that extend through the weak and compressible clays and peats commonly encountered in southern Louisiana. Since the piles are battered, settlement of the compressible foundation soils can result in loads acting normal to the piles and induce pile bending moments. Therefore, the design of pile-supported T-walls is a complex soil-structure interaction problem that requires detailed and careful numerical analysis to accurately estimate the stresses and bending moments in the piles. For this paper, numerical analyses were performed for three cross sections that each included a two-pile T wall system that was installed within a 15-ft tall new levee embankment. The cross sections were identical except that the elevation of the T-wall base was varied. This paper discusses the analyses, and it compares the influence of settlements and flood loading on the pile stresses and bending moments. In addition, this paper includes general recommendations for the analysis and design of pile-supported T-walls in practice.INTRODUCTION AND BACKGROUNDThe recently completed Greater New Orleans Hurricane and Storm Damage Risk Reduction System (HSDRRS) includes 350 miles of levees and floodwalls and is designed to defend against a 100-year storm surge event. The floodwalls predominantly consist of I-walls and T-walls. I-walls are comprised of a sheet pile wall curtain capped with a monolithic concrete wall above grade. T-walls are similar to I-walls, but they include a wide concrete base at grade, which forms an inverted “T” shape, and they are generally supported by long batter piles that provide additional lateral and rotational stability for resisting flood loads.During Hurricane Katrina, several I-walls failed, resulting in large breaches and devastating flooding (Duncan et al. 2008, IPET 2009). T-walls on the other hand performed quite well, including T-walls that were overtopped and eroded on the protected side, yet still did not collapse. As part of the HSDRSS, more conservative designs and height restrictions were required for I-walls (USACE 2011), and a number of I-wall sections were replaced with T-walls. However, the design of pile-supported T-walls is complex and requires careful consideration of both flood loading and settlements."

Jan 1, 2017

By Rozbeh Moghaddam, William D. Lawson, Priyantha W. Jayawickrama, Hoyoung Seo, James G. Surles

"This study provides calibration of resistance factors (?) for design of driven piles to implement Load and Resistance Factor Design (LRFD) for bridge foundations using Texas Cone Penetration (TCP) Test data. The basic research approach was to compile a database of published full-scale load tests including projects from the Texas Department of Transportation’s (TxDOT) historical archive and projects from neighboring state DOTs. Load test results from neighboring states were leveraged by performing new geotechnical borings with TCP tests at the project sites. The final dataset consisted of 30 load tests performed on precast square concrete piles, with pile widths ranging from 356 to 508 mm and penetration depths ranging from 5.2 to 25.5 m, driven in soils. Ultimate capacities for each load test were interpreted based on Davisson, 5%, and 10% settlement criteria. These measured ultimate capacities were compared against predicted capacities estimated from TCP blow count values (NTCP) and design charts following the procedures outlined in TxDOT’s Geotechnical Manual. From the comparisons, statistical parameters of the biases (??= measured capacity/predicted capacity) such as mean and coefficient of variation were obtained. Resistance factors (?) for LRFD were then determined using Monte-Carlo simulations for each ultimate capacity criteria with the target reliability indices of 2.33 and 3.00.INTRODUCTIONThe Texas Department of Transportation (TxDOT) has used the Texas Cone Penetration (TCP) test since its development in the 1940s. The TCP test is an in-situ penetration test to characterize the materials encountered during geotechnical exploration. Texas currently maintains over 53,000 bridges in the National Bridge Inventory (FHWA 2016), and most of these bridges plus other transportation infrastructure in Texas are supported by foundations designed using the TCP test and its associated foundation design method. The Oklahoma DOT adopted the TCP test and foundation design approach in the 1970s, so the foundations for most of the 23,000 bridges in Oklahoma’s inventory were also designed using the TCP method. With this significant body of experience, the TCP method has been viewed as a straightforward, relatively easy-touse foundation design method that consistently yields safe, serviceable, economical, and maintainable foundations. TxDOT’s deep foundation design method is documented in the TxDOT Geotechnical Manual (TxDOT 2012) and currently employs the allowable stress design (ASD) approach. However, the Federal Highway Administration (FHWA) has mandated that the states begin to implement the LRFD method in place of the older ASD approach (Densmore 2000). This paper presents resistance factors at ultimate limit state (ULS) for design of driven piles using the TCP test, resulting from efforts to be in compliance with the FHWA policy."

Jan 1, 2017

By John A. Dal Pino

This paper describes two independent building underpinning projects during the construction of the Los Angeles Metro Rail System. The first project involves pinpile underpinning of a building along the Red Line which is the main heavy-rail portion of the system. Vertical and inclined friction pinpiles were constructed, using drilling equipment in a low-overhead height space, to support underpinning grade beams. This underpinning permitted the demolition of the building caissons so that the subway tunnels could pass beneath the building unimpeded. One of the piles was statically tested in compression. The second project involves the use of traditional pit piers for the underpinning of historic buildings along the Pasadena Blue Line, which is one of the light-rail branches from the Red Line. The piers were designed for various loading conditions and to minimize differential settlement of adjacent foundations. The piers will be internally braced with steel struts to be designed by the contractor.

Jan 1, 1996

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By James E. Maccariella

Replacement of an existing movable bridge with a new low level fixed bridge would not accommodate potential future navigation traffic. In order to replace the existing bridge in a cost effective manner, while accommodating the potential future needs of the Port of Salem, a new bridge was proposed that would permit conversion to a vertical lift type movable bridge should a potential need for upstream navigation warrant such a project in the future. Drilled shafts were found to be the most desirable foundation type for the replacement of the Route 49 Bridge over Salem River. Their ability to resist scour, be constructed without cofferdams, adequately resist vessel collision forces, and accommodate conversion to a future vertical lift bridge allowed the project to meet both the needs of the New Jersey Department of Transportation and the Port of Salem.

Jan 1, 2005

By V. M. Troughton

Large diameter bored piles with grouted bases have been adopted for the foundations of the majority of the buildings at Canary Wharf in London's Docklands, including a deep basement car park. The piles are founded in the Thanet Sand which forms part of London's aquifer where water levels are reported to be slowly rising. A special pile test has been carried out to determine the effects of both the basement excavation and a possible long term rise in the groundwater level on the performance of base grouted piles. These effects were simulated by injecting water around the pile toe and thus reducing the vertical effective stress. In this paper the test layout and procedures are described and the results are presented. The test results showed that the reduction in pile base resistance under increased water pressures was less than predicted by conventional design methods based on vertical effective stress. The end bearing resistance was found to be proportional to the mean effective stress.

Jan 1, 1989

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By Richard A. Forth

During the construction of the Island Line (ISL) in Hong Kong between 1982 and 1986 piled foundations of a building were encountered in a tunnel drive. As the tunnel alignment could not be changed work was temporarily suspended whilst grouting took place beneath the pile cap. The tips of the piles were then cut off. The normal precast concrete lining segments were replaced by the "stiffer" spheroidal graphite iron segments and tunnelling resumed. Settlement of the building was found to be under 10 mm due to the tunnel drive and no damage was reported to the building.

Jan 1, 2002

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By Michael J. Brown

Load testing is important for controlling the quality of piled foundations. The Statnamic test is an alternative to existing testing methods with a load duration that lies between that for static and dynamic tests. Current methods of analysis offer excellent correlation between static and Statnamic tests for coarse-grained soils but often over-predict the capacity for fine-grained soils. Thus a calibration chamber is being used to produce instrumented beds of clay with reproducible properties. A model pile placed in the beds can be loaded at varying rates using a computer controlled servo-hydraulic system. Results from the modelling will be used to improve methods of analysis and govern the design of a full-scale study. Initial results suggest the rate effect can be represented by a power law relating pile velocity and resistance. Statnamic loading of the model pile produced large negative pore pressures in the clay bed.

Jan 1, 2002

By M. Reza Saberi, T. Ted Miyake

Driven piles are a common tool in any engineer’s toolbox for supporting large structures over very soft ground, especially in high seismic risk zones. Challenges include achieving sufficient vertical and lateral load capacities within the constraints of pile spacing and geologic conditions. This was the case for a project in Orange County, California with a state-of-the-art, $180 million plant for biosolids processing, biogas management and energy recovery located in marshland next to an existing waste water treatment plant. The new construction for the Irvine Ranch Water District included a 70-foot (21 m) tall building and three closely spaced, 90-foot (27 m) high, 65-foot (20 m) diameter, egg-shaped steel digester tanks. The lower 35-feet (11 m) of the tanks were constructed below ground level. The site was underlain by up to 45 feet (14 m) of highly compressible peat and organic clays with standard penetration test (SPT) blows as low as 2 blows/ft (30 cm). Some of the peat layers had measured in-situ dry densities of less than 30 pcf (480 kg/m3) with moisture contents of over 250 percent. The soft clays and peat were underlain by a dense layer of sand and gravel at depth. Groundwater was very shallow. While nearby sites were designated by others as seismic site class “D”, this site was clearly class “F” (SF) which required site specific seismic hazard and time history analyses. Six recorded time histories were selected from the 1994 Northridge, 1989 Loma Prieta (California) and 1999 Chi Chi (Taiwan) earthquakes for the ground motion analysis considering the magnitude of the earthquake, distance to the source, characteristics of the earthquake source (i.e. type of fault displacement), peak ground acceleration, local site geology, station type (i.e. free-field or small structure stations), and spectral content that was similar to the period range of interest. Following ASCE’s Guideline Document 7-05, a site-specific horizontal acceleration response spectra (ARS) was developed for the maximum credible earthquake (MCE) associated with the site.

Jan 1, 2018

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By S. Narasimha Rao

Bored cast in situ piles are highly susceptible to construction defects like necking, discontinuity in concreting, poor compaction of concrete, improper end bearing condition due to inadequate cleaning of bore hole, exposure of reinforcement, segregation of concrete etc. There is a necessity to understand the behavior of piles so as to design effective foundation system. In this paper investigations of two field cases were discussed to bring out the effect of defective piles. In one case improper end bearing has been discussed for a concrete pile of length of 45m and diameter equal to 1.2 m and is reinforced with 32 no's of 28mm diameter steel bars and in another case necking of the pile has been discussed. Further model piles with preformed defects have been tested in laboratory to bring out the influence of defective piles.

Jan 1, 1996

By R. G. Shen

The relation curve of strain and acceleration is presented in this paper. The steel pipe pile of 609.6 mm in external diameter driven by IDH-45 diesel motor hammer on the esturial shoal of Yangtze River. The ultimate bearing capacity of pile is analyzed by one dimensional wave equation and the effect of computational parameters of the equation is discussed.

Jan 1, 2010