Search Documents

By James J. Tansey

A Deep Foundations Institute meeting with the University of Michigan at Ann Arbor in March of 1984 featured legal rights under Differing Site Conditions. A workshop conducted by the authors and Gerard Ittig, Esq. added to the value of the symposium. This paper will be of interest to your attorneys in any subsurface disputes.

Jan 1, 1985

By Mohammadreza Khanmohammadi, Kazem Fakharian

"AbstractIn driven piles, the gradual dissipation of excess pore water pressure and consequently the soil setup significantly contribute to increasing the pile capacity with time. The question is risen that how the scale differences affect the stress state variations around the pile shaft and at the pile tip? Would the CPT predictions better correlate with End-Of-Drive (EOD) or Beginning of Restrike (BOR) conditions? On the other hand, are the proposed a and ß parameters for clayey soils mostly predicting the EOD or BOR situation? The main objective of this paper is to back calculate the a and ß parameters from CPT profiles, pile Dynamic Load Tests (DLT) at the EOD and BOR as well as Static Load Tests (SLT) and evaluate how they compare with those suggested in literature. Four precast 400 mm square concrete piles driven in North Azadegan Oilfield in Khuzestan Province were selected for the comparisons. CPT test results were available from the extensive geotechnical investigation at the study site. DLT tests using PDA were carried out at EOD, 1 day and 14-day BOR on all the 4 piles. All the piles were SLT tested as well. The UniCone software was used to estimate the tip and shaft resistances using 4 methods including the Dutch, Eslami & Fellenius, LCPC and Schmertmann. The results indicate that the a-method based on the proposed values in literature has predicted a shaft capacity of 90% of the 14-day BOR. This is while the ß-method has predicted a shaft capacity equivalent to 1-day BOR results only. Therefore, both methods have under-predicted the shaft capacities compared to real capacities measured after the significant soil setup in the study area. Two of the CPT methods have underestimated, one has overestimated and one has matched the estimated 60-day capacity."

Jan 1, 2014

By Bengt H. Fellenius

"ABSTRACTAn example from a guidelines document for the Eurocode is discussed that addresses design for geotechnical strength of piled foundations in settling soil, generating drag force and downdrag. A modified example of geotechnical response is then analyzed in a failure mode, Ultimate Limit States (ULS), and stationary long-term state, Serviceable Limit States (SLS). It is shown that the Eurocode principles, when applied to correctly determined forces, results in an irrational and costly design. The results of the analysis of the modified example are applied to eight different codes pertaining to piled foundations from USA, Canada, Europe, and other countries. Several of the codes require that the drag force be included as a load in a ULS design, which an absurd and costly requirement, in some codes, in one case made even worse by combining drag force with live load. A major weakness of almost all codes is their minimal treatment and sometimes total absence of aspects of settlement of piled foundation. In contrast, my main argument is that design for capacity, whether in working stress approach, or by LFRD or ULS approaches, is not always safe unless a thorough settlement analysis shows that the design also meets the requirements of the SLS.1. INTRODUCTIONFirst, there were analysis, design, and construction establishing a State-of-Practice, SOP. Then, came codes and specifications summarizing the SOP, as interpreted by a committee. When the state-of-art, SOA, was not understood by that SOP-interpreting committee, the codes and specifications are uneconomical and, sometimes, also unsafe.The paper first presents an example quoted from two commentaries on the Eurocode 7 on design for geotechnical strength by the Eurocode (1997). The example is then modified to a more realistic case and analyzed in failure mode (ultimate limit states, ULS) and in the context of settlement (serviceability limit states, SLS). The analysis results are then applied to eight codes addressing piled foundation design and changes necessary for the referenced codes and specifications to be closer to the SOA are identified."

Jan 1, 2014

By Gary Kuhns

Central Florida is among the fastest growing urban areas in the United States, and its rapid development has required the steady construction of various types of civil engineering works. The karst geologic terrain and variable geotechnical conditions, however, present special challenges to the design and construction of deep foundations. The subsurface profile can be idealized as a surficial layer of Pleistocene sands, underlain by the highly variable Miocene-age Hawthorn Group, consisting of various combinations of sand, silt, clay, phosphate and highly weathered limestone. The Hawthorn Group is underlain by Eocene-age limestone that comprises the Floridan aquifer. Vast networks of solution cavities are present throughout the Eocene limestone, sometimes allowing downward raveling of the overlying soils and the creation of sinkholes. In some cases, the relic sinkholes can be filled with soft compressible organic soils extending to depths greater than 100 feet (30.5 m). Driven piles are frequently employed as a deep foundation alternative, although occasionally cast-in-place piles/shafts have also been used. Piles are often driven for bearing in the weathered limestone within the Hawthorn Group, but are sometimes installed as friction piles in the upper soil and intermediate geomaterials. Dynamic pile testing is routinely performed during pre-construction test pile programs, or during production for quality control and assurance purposes. This paper presents discussions on the design and construction aspects of deep foundations unique to Central Florida subsurface conditions and local practice. Foundation issues such as subsurface variability, soil setup, pile damage, negative skin friction, and sinkhole conditions are discussed with the aid of demonstrative case histories.

Jan 1, 2003

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By J. W. Wang

This article first explains the mechanism of forming strength in the Jet grouting reinforced foundation, and points out the function of cement hydrates and clay minerals in clayey soil, the reinforced body with the character of long-term growth of strength. Secondly, regarding the strength and the deformation characteristics of compound foundation, the article points out that the stress-strain curve of the jet grouting pile is approximate to hyperbolic curve. Finally, the article cites three examples of application in the construction of the metallurgical industry.

Jan 1, 2010

By Sanjeev Malhotra

The American Petroleum Institute (API) method of predicting pile capacities in sands is reviewed. Factors that influence pile capacity such as soil parameters, pile parameters, loading effects and installation effects are listed. In addition, the simultaneous occurrence of physical phenomena such as grain crushing, pile shaking, stress-redistribution and plugging add to the uncertainty in the prediction model. To better understand the method of prediction, each parameter and the associated uncertainty is revisited. It is evident that these factors are inter­related and sometimes compensating. This discussion also draws attention to the influence that pile installation procedures can have on pile capacities and highlights the need for field experience with various pile installation procedures for designers. In summary, the strength of the method lies in its simplicity and ease of application, but the possible savings generated by an improved method are too substantial to ignore.

Jan 1, 2000

By R. T. Stain

Dynamic methods of load testing piles using a drop hammer to generate the input force have been in use for many years. These systems are based on the wave equations developed at the Case Institute of Technology, Cleveland, Ohio in the late 1960's and are well documented. Such tests are generally restricted to preformed driven piles, the driving hammer being a convenient means of generating large input forces. In 1979 the CEBTP (France) was sponsored by the FNTP (Fédération Nationale des Travaux Publics) to undertake research into existing classical methods and to develop a test that would be equally applicable to bored cast in place piles. The result of this research programme is a methodology known as SIMBAT, and which was included in a series of class A prediction trials in Belgium in 1987 (Refs 1 & 2, Paquet 1987, 1988). The purpose of this paper is: a) to examine the type of 'dynamic'/'static? load test correlations that can be obtained. b) to highlight the differences between the classical' methods and the 'SIMBAT' technique.

Jan 1, 1989

By Giovanni A. Bonita

The new Embassy of the Peoples Republic of China in the United States (Chinese Embassy) is located in the Embassy Row portion of Northwest Washington DC. The 475,000 ft2 (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. The structure approaches the property line on all sides, and is immediately adjacent to several foreign embassies and a secure U.S. Federal Building. A vertical soil nail wall was used as the primary support of excavation (SOE) system for the project. The soil nail wall was irregularly shaped, benched in areas, and reached total heights up to 98 feet (29.9 m). The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Tight excavation requirements were defined for the project due to the location of the building relative to the property line, requiring fairly precise wall positions and shotcrete tolerances. Design challenges included soft soil conditions, inside wall corners, underground utilities, and seismic impacts from blasting. The paper will focus on the design, construction, and performance of the soil nail SOE system, as well as touch on the logistical and political factors that influenced the design. The paper also notes the Value Engineering and communication approaches that were generated during construction. These efforts resulted in a significant improvement in the quality control and quality assurance exhibited on site, expedited the schedule, and led to significant cost savings to the contractors, engineer, and owner.

Jan 1, 2006

By Mark M. Petersen

As part of the addition of eight new combined cycle generating units at the Florida Power & Light Sanford Plant, 2,129 piles were to be installed. The existing plant elements were supported on driven piles, and the variation in pile lengths during previous work, as well as available subsurface information, indicated a complex stratigraphy. At the request of the owner, the designer/construction manager developed a program to evaluate the use of pressure-grouted displacement piles. A pre-design load test program in areas that represented the apparent extremes in subsurface conditions indicated that the system was feasible; however, the presence of existing features that were to be demolished later precluded the clear delineation of subsurface conditions in advance of construction. A contract was negotiated with the pile installer based on the best estimate of potential pile lengths, with modifications to pile lengths to be set based on additional exploration. A total of 52 cone penetration soundings and five load tests were performed immediately prior to and during pile installation to establish correlations between the CPT data and pile performance. Pile depths were set based on these correlations. Pile installation was completed 6 weeks ahead of schedule and 15 percent under the original budget estimate. This paper documents the evaluation of pressure-grouted displacement piles as an emerging technology, and illustrates the benefits of a close working relationship between the owner, designer, and pile contractor at a site with variable subsurface conditions.

Jan 1, 2002

By Timothy D. Stark

Jet grouting has increasingly become one of the ground improvement technologies used to address seepage concerns and to provide strength improvement of soils. The technique of jet grouting uses high pressure/velocity jet fluids to erode the existing soil and then to mix the cuttings with cement slurry to form soilcrete. Excess slurry or spoil is ejected to the surface. If the native soil is not completely mixed with slurry, the resulting columns will have soil inclusions which can reduce the strength of the column and/or increase the permeability of the column. A jet grout test program at Tuttle Creek Dam shows that the completed large diameter columns contain perhaps 40 to 50% or more of native soil that was not broken up and mixed during the jet grout process. The test program included excavation of full-scale columns to a depth of 35 ft (10.7 m) for visual inspection and testing. Additionally, six of the columns were cut or sectioned to investigate the interior of the columns. The observed inclusions include significant amounts of both fine grained (silts and clays) and coarse grained (fine sands and sands) soils. Evidence suggests at least two explanations: (1) fine grained soils can be difficult to erode and break up into small enough particles that can be ejected to the surface, especially if at low natural water content, and (2) when large diameter columns are being excavated, the excavated roof of the cylindrical cavity may be unstable and may collapse. With this roof instability large slabs of material can break off, fall into the slurry and escape the cutting and mixing action of the rotating jets. This paper describes the Tuttle Creek Dam test program, inclusions observed in the completed columns, and suggests potential causes of the inclusions.

Jan 1, 2009

Since the 1989 Loma Prieta Earthquake in the San Francisco Bay Area, the California Department of Transportation (CALTRANS) has accelerated seismic upgrading of their bridges. Many structures can be improved with the simple addition of hinge seat restrainers. Others require modification of column bents and superstructure to column connections. Often, footing retrofits are necessary, which require the addition of tension/compression elements (compression piling and tiedowns anchors) to resist overturning moments substantially larger than those originally used for footing design. These footing retrofits may include doweled reinforced concrete footing extensions or new pile caps which transmit forces to either driven steel or drilled concrete piles. In some cases, installation of these traditional piling elements is expensive, impractical or impossible due to: low overhead clearance, ground obstructions, high water table, noise or vibration sensitivity, or the inability to laterally expand the existing plan dimensions of the footing. In the latter case, one practical option is to attach small diameter drilled and grouted tension/compression piling elements (Pin Piles) to the existing footing. The footing may be strengthened with dowels and added concrete thickness or there may be a reduced shear span due to the installation of larger or jacketed columns. A reduction of elements is available with a Pin Pile alternative, particularly when the selection of traditional standard piles is governed by the reduced tension/uplift capacity available from the traditional elements, since Pin Piles exhibit superior uplift performance.

Jan 1, 1993

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006

By D. Michael Holloway

The realignment of Interstate 880 replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the proposed structures. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers and prospective contractors well beyond the limits of local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata, and quantifying the effects of installation on the long-term capacities of the piles, led CALTRANS to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1996

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By Kirk A. Mcintosh

Augered, cast-in-place (ACIP) piles have been utilized in the United States for a wide range of projects since the 1950's. Due to the cast-in-place nature of the installation method (and lack of a driving criteria); however, ACIP piles have not been readily accepted by some practicing geotechnical and structural engineers. Since ACIP piles were initially developed, the installation equipment and techniques have been improved and refined and the number of experienced contractors has significantly increased. Over the past 10 to 15 years, the pile type has experienced significant growth in the United States (particularly in Florida) because engineers have become more knowledgeable and comfortable with its use. The Miami area, in particular, has experienced considerable growth in the utilization of ACIP piles primarily due to their usage on the $1 billion Miami Metrorail System project in the early 1980s. The economic advantages over other deep foundation types, coupled with some unique installation advantages, have shown that ACIP piles can be a viable foundation alternative on many projects. Even though ACIP piles have gained respect in the private sector, the pile type has generally not been readily accepted by government transportation agencies. The reluctance to readily accept this foundation type stems primarily from the quality assurance aspect of cast-in-place pile construction. Additionally, there has not been much research activity on this foundation type, technical papers, formal associations (other than the DFI), or a concerted effort to standardize the industry. This paper serves to discuss the state of practice for ACIP pile installation in the state of Florida.

Jan 1, 1997

By Thomas C. Anderson

Tiedback walls are now recognized and accepted as a good solution for a variety of structural problems: ? Retaining Walls and Bridge Abutments in cut situations ? Landslide stabilization ? Repair/support of existing walls Acceptable techniques have been developed for anchoring in cohesive and granular soils and in any kind of rock. Methods have been developed for adequately protecting tieback tendons against corrosion and for testing every tieback to verify its long-term load-carrying capacity. However, the major problem that the industry faces today is how do we get constructable and economical tiedback walls contracted for and built with minimal claims. This paper will explore the issue of "constructability" through a look at specific problems from actual projects. From a research report from the Construction Industry Institute, Austin, Texas (1986), constructability is defined "as the optimum use of construction knowledge and experience in planning, design, procurement and field/operations to achieve overall project objectives." Maximum benefits occur when people with construction knowledge and experience become involved at the very beginning of the project." The design and installation of tiebacks has been developed primarily by specialty contractors; each contractor has evolved its own methods of performing the work, and consequently, many of the techniques are patented and proprietary. The real question is, how do we make effective use of this knowledge and experience during the design phase of the project?

Jan 1, 1991

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006