Search Documents

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

By James R. Lang

The Xietongmen deposit is located 350 km west of Lhasa, Tibet. It is a new, high-grade porphyry copper-gold discovery and the first deposit to be systematically explored by a western company in southern Tibet. In 2005, Continental Minerals Corporation drilled 21,332 m of core in 63 holes and demonstrated excellent lateral and vertical continuity of high-grade copper-gold mineralization over an area 750 m by up to 350 m in size which remains open in all lateral directions. Drill intersections repeatedly yield grades >1% Cu equivalent (based on gold and copper prices) and include 308.5 m at 0.87% Cu and 1.25 g/T Au (1.60 CuEQ%), and 315.6 metres at 0.61% Cu and 1.11 g/T Au (1.26 CuEQ%). Extensive drilling in 2006 will expand and delineate the deposit, and metallurgical, engineering, environmental and socio-economic evaluations will begin. Xietongmen is hosted by volcanic and intrusive rocks of the Gangdese belt, a magmatic arc active between 120 and 30 Ma along the southern margin of Eurasia. Pervasive alteration is dominated by a well-mineralized K-feldspar and biotite assemblage, and by a more peripheral sericitic assemblage also with strong chalcopyrite. Major vein stages include chalcopyrite-bearing quartz, biotite, magnetite and pyrite-pyrrhotite types.

May 1, 2006

By Barara Rose

Presentation Outline ?Introduction of BMS ?Resource Integration Process ?Methodologies ?Tools ?Case Studies ?Zone 01 : 725 SOZ ?Zone 16/17 : 1000 NRP ?Conclusions

Oct 1, 2010

By Cardm Jeffrey W.

The decay of 222 Rn yields a series of short-lived decay products which become attached to the surface of a plate or wire exposed in a 222Rn-bearing atmosphere. The alpha-activity of two of the decay products, 218Po and 214Po, can be measured by simple counting techniques. This phenomenon may have direct application to uranium exploration. Laboratory studies have shown that: (a) radon decay products can be collected on a wide variety of materials (including various kinds of metals and plastics); (b) activity increases as a function of the surface area of the 'collector; and (c) the collection of the decay products is enhanced by applying a negative charge. The new technique was used in situ to delineate the anomaly above the South March uranium-copper occurrence. A related technique was developed to measure radium in soil samples. The results of both studies compared favourably with those obtained from conventional methods.

Jan 1, 1979

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985

By Robert B. Parsons

"Originally intended to be implemented in 1977, but actually introduced effective May 6, 1974, the earned depletion regulations have been substantially refined and modified since their appearance on the Canadian tax scene, so that this important legislation now consists of a highly complicated set of rules which even the most astute follower of tax law has considerable difficulty sorting out!This month, Tax Notes attempts to cut through this bewildering array oj regulations, in reviewing the main features of the earned depletion allowance applicable to mining operations. Despite the phase-out of earned depletion allowances for most oil and gas operations as part of the federal government's new National Energy Program, earned depletion provisions are still alive and well for the mining sector, although they might well be slowly strangling to death in their own entanglement of complexity!"

Jan 1, 1981

A rough simulated borehole has been developed for the installation and dynamic testing of rock bolts a the WASM Dynamic Test Facility. The rough simulated borehole is used for rock bolts that are sensitive to equipment installation technique or borehole geometry (particularly friction rock stabilisers and resin encapsulated bolts). An extensive axial test program has quantified a difference between the static and dynamic capacity (kN/m of embedment) for friction rock stabilisers once sliding starts. The 47mm split tube bolt has a 50% reduction in embedment capacity (but with significant variation) dissipating 2.7kJ/100mm of sliding per meter of embedment, and the Omega (inflatable) bolt had a 70% reduction in embedment capacity dissipating 6.2kJ/100mm of sliding per meter of embedment. The Omega bolt dynamic capacity remainder at least equivalent to the split tube bolt static capacity.

May 1, 2009

By Julie Culverhouse, Dennis Grimm, Kieran Harding, Jean-Francois Boulanger

"Agrium’s Canadian Phosphate Business (CPB) is comprised of Kapuskasing Phosphate Operations (KPO) in Northern Ontario, Canada’s only operating phosphate mine, and Redwater Phosphate Operations (RPO) in Alberta, which manufactures the fertilizer from KPO’s concentrate.Production from KPO’s South Pit commenced in 2009 and introduced contaminant problems: high aluminium from crandallite and kaolinite clays. These issues caused a drastic decrease in P2O5 recovery and throughput in both plants. KPO attempted to reduce Al clays by means of aggressive desliming. Meanwhile RPO experienced high amounts of dissolved metals in their feed that are detrimental to fertilizer production.This paper covers the mineralogy of the problem, its impact on contaminant separation at KPO, on RPO’s process and on Agrium’s Canadian Phosphate Business as a whole.Potential solutions to the problem are discussed and analysed, including a process change to deslime high aluminium streams more aggressively and high grade ore flotation, which is atypical at KPO. The latter is a demonstration of the value of communication between the concentrator and the client, as KPO accepted a recovery loss and increased production costs in order to increase overall CPB profits. General lessons learned are discussed, followed by a section on ore blending.INTRODUCTIONAlthough the existence of the Kapuskasing phosphate deposit has been known since the 1970s, it’s only since 1999 that Agrium has been operating the Kapuskasing Phosphate Operations (KPO). The mine consists of three major pits (Center, North and South) from which a mining contractor hauls the apatite ore to the Agrium concentrator. The beneficiation plant processes the ore, separating contaminants such as Fe, Mg and Al which are detrimental to its client, Agrium’s Redwater Phosphate Operations (RPO). The KPO concentrate is finally thickened, filtered and dried before being shipped by rail to RPO.At the Redwater plant, the KPO concentrate is added to a sulfuric acid solution in an attack tank, to create a phosphoric acid solution and gypsum:"

Jan 1, 2011

By H. P. Dibbs

An account is given of the application of neutron activation analysis to the rapid, non-destructive determination of copper in minerals, using a 14-MeV neutron source. Elements that interfere in the determination of copper by this method are given, together with the errors in the estimation of copper that result from the presence of varying amounts of these elements. The possible use of a compact "sealed-tube" 14-MeV neutron generator for the field assay of copper in minerals is discussed.

Jan 1, 1970

By Júlio C. Lúcio

Consider the case of a mining company with N investment opportunities in projects of different commodities. The problem is: since the company has limitation of capital, equipments, technical staffs, etc, what is the best portfolio of production projects in order to maximize expectations from shareholders? In the no-longer past, the traditional method for the selection of portfolio of projects was the rank-an-cut method. But, this does not properly account for the risk to which the company is exposed. The Markowitz?s Mean-Variance is an advance because the risk of the NPV can be estimated at the level of the company or even division of the corporation. The final product of the Markowitz?s model is the efficient frontier, in which, the manager can clearly understand the maximum return from existing assets and the associated risk level - but this model does not recommend which one is the best portfolio. In this paper we present a model to select the best portfolio considering not only economic indicators, but also requirements of production, constraint in investments, etc. We show that if investors are diversified, managers should select projects with highest return, regardless of risk. However, in practice, if bonuses of managers are tied to their performance, the choice for portfolio with lower return and risk can happen. Numerical application considering typical portfolio of large mining company is used as example.

May 1, 2009

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By K. B. Culver

"This paper provides background information on the expansion programs of Rio Algom Limited at Elliot Lake. Included are details on the Quirke expansion program, the Panel mine rehabilitation program, including the selection procedure for the tailings containment area, the Stanleigh mine rehabilitation program, housing, government regulations and the Environmental Assessment Board hearings. Introduction After 2Y2 years of public hearings, 4 years of arbritrating differences of opinion between our engineers and government licencing authorities, interspersed with research into radium removal and development of the LAMIX process and carrying out the work associated with some 24 control orders issued to us by the MOE, it is very difficult to compress all of the experiences and frustrations into a single paper. The highlights, as they relate to the expansion programs of Rio Algorn Limited and its affiliate, Preston Mines Limited, will be covered. Denison Mines Limited, of course, is the other uranium producer in Elliot Lake. They are currently in the process of expanding from 7,000 to 11,000 TPD by the second half of 1980 and then to 15,000 TPD by the mid 1980's. In giving this overview, the following seven items will be discussed: • The basis for Rio Algom's and Preston's expansion plans. • The Quirke Expansion. • The Panel Rehabilitation. • The Stanleigh Rehabilitation. • Housing Programs. • Government Licencing Requirements. • Environmental Assessment Board Hearings."

Jan 1, 1980

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

By Chris Larsen, Carole Fortin, Dave Scott, Curtis Deredin, Ian Orford, Jean Guy Gauthier, Andy Trusiak, Lyne Côté, Mike Cooper

"Upon successful commissioning of the Stage Grinding Project (Cormier et. al., 2002), process improvements predicted through pilot plant testing were obtained in several flotation circuits, resulting in higher grades and recoveries for zinc and lead concentrates. Subsequent to establishing new baseline operating conditions from the Stage Grind Project implementation, additional opportunities were identified, and through the application of Six Sigma methodologies further gains were made. Six Sigma improvement projects were carried out in the copper-lead, zinc, lead upgrading and bulk flotation circuits. The overall performance increase resulting from incremental improvement projects has been substantial.Most remarkably, given the operational maturity up to the late 1980’s, the Brunswick concentrator team has continued to deliver a steady stream of major improvements over the past fifteen years. While senior managers and their programs have changed several times, there have been some critical constants over the long run. Common elements have been a commitment to team work, a commitment to recruit and maintain technical personnel, a structured business improvement framework supported organizationally by senior management, and focus on a few priority initiatives rather than trying to fix everything at once.The paper briefly discusses the longer term setting and then endeavors to illustrate, with examples, how improvements are presently achieved by applying the Six Sigma quality program.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s larger lead/zinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 mine. In excess of 100 million tonnes have been milled to date. The concentrator employs differential flotation to produce lead, zinc, copper, and lead/zinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2005

By D. Lindeman, R. M. Nendick

"From a technologist's point of view, there have been few fundamental 'breakthroughs' in the process of gold extraction since the turn of the century. However, the industry has made a great deal of progress in its response to the problems that have arisen: a changing demand for products, lower grade and more refractory ores, inflated labour and materials cost and the increasing control of governmental legislation. The trend in North America and South Africa to alleviate these problems has been to adopt a common policy to process larger tonnages of lowgrade ore through more efficient milling circuits. Here, however, is where the similarity ends.The purpose of this paper is to emphasise the different principles of practice employed by extraction plants in North America and South Africa to achieve the same common goal, namely gold bullion.2.0 INTRODUCTIONTwo very important aspects of extraction metallurgy for which the metallurgical engineer is responsible are plant design and plant commissioning.In North America and South Africa the importance of these aspects is due to the fact that both are related to the financial success of the project of which they form part. Good design is imperative if the capital invested in both the plant and the whole mining undertaking is to reap maximum profit. Furthermore, good design leads to a carefully planned and well executed start-up procedure resulting in bringing the plant into production on time, at designed efficiency and within budget.Due to the competent nature of the quartz pebble conglomerate and quartzite ore on the South African Witwatersrand, the characteristics of the ore type are not much different from one mine to the other. Thus a significant operating knowledge and experience has been built up over the years and there is considerably less risk in selecting a gold extraction process route."

Jan 1, 1992

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By Theodore H. Boggs

The battle of the gold standard is not limited to one country alone, or even to a single group of countries. It is being waged merrily in many important commercial and industrial quarters. Though it is not always a practical issue calling for immediate attention, it is none the less, quite widely, engaging the thought of bankers and other students of finance. The controversy arises, in the last analysis, because of the desire of men to secure a stable currency. There are two ways of restoring a reasonably stable currency system: (1) the re-establishment of the gold standard, or (2) the deliberate and artificial management of a paper currency. Both systems are well known. The gold standard was in use prior to the war in the principal commercial countries. A currency of inconvertible paper has been at times employed in the past in various countries; for example in Britain from 1797 to 1821, and in the United States from 1862 to 1879. The gold standard, as all are aware, implies the selection of gold as the standard of value. The unit of value is a fixed weight of gold and, so long as the standard remains unimpaired, all other means of payment are maintained at a parity with standard gold coins. And gold coins alone constitute the standard money, inasmuch as their value as bullion equals their value as coins. Under the gold standard this would not be true of any other form of money, although all other varieties of money, including bank notes, government notes and silver coins would be freely convertible into gold money. Strictly speaking, the gold standard also implies that the gold money in turn shall itself be freely convertible, through melting, into gold bullion and freely exportable.

Jan 1, 1925

"This paper describes some of the methods and equipment used for fine milling of minerals, and gives particular attention to the Vibro Energy system.In addition, the paper describes a specific application in the gold mining industry. This is the 200 tpd plant built by Anglo American Corporation at the President Brand Mine in South Africa in 1985, now a division of Freegold. This plant treats a gold bearing pyrite flotation concentrate which is finely ground to 15 microns prior to cyanidation and carbon-in-pulp (CIP). l .0 INTRODUCTIONFree milling gold ores are those that yield acceptable dissolution and recovery of the gold following grinding to what can be described as normal fineness, frequently between 50% and 90% passing 74 microns.Increasingly, gold metallurgists are faced with ores that are refractory. The traditiona1 treatment route for refractory gal d ores and concentrates has been by roasting, but for environmental reasons this is becoming less acceptable, or in some areas of the world, totally unacceptable. New methods of treating refractory gold ores are being developed and applied in practice. These new methods include pressure and biological oxidation. Higher gold liberation can also be attained by increasing the fineness of grind, although with conventional systems there are economic limits to this.In flowsheet development and test programs on new deposits, a standard procedure is to establish the relationship between the grind and subsequent go 1 d extraction. The normal situation is that gold extraction increases as the ore, or concentrate, is ground finer. Typically, this relationship is as shown in Fig. l, where the incremental additional extraction is very small once an optimum, or economic, grind has been achieved. This generally app1ies whether the material is free milling or refractory. The limits to grinding are set by the type of equipment which is commonly in use, usually ball mills. These mills have the obvious advantage of high capacity, however, they are increasingly inefficient as finer grinds are required. In general, ball mills are used to reduce ore to some agreed percentage passing 74, or possibly 53 microns."

Jan 1, 1988

By P. Wells, P. Quinn

"A moveable flotation miniplant was designed and constructed at the research laboratory of Inco Technical Services Ltd. to address the need for flowsheet development with a limited amount of ore (such as drill cores). It consists of one rod mill, two regrind ball mills, one vibratory screen, 24 flotation cells of various sizes and two Venturi aerated flotation columns. The setup has continuous monitoring capability for pH, dissolved oxygen, oxidation-reduction potential, conductivity and temperature in conditioning tanks and flotation cells. Various options regarding flotation reagents, circuit configurations, and fineness of primary grind and regrind can be readily evaluated. The throughput of the miniplant is 20 – 30 kg/hour ore.Unit operations such as flash flotation, magnetic separation and gravity concentration can also be evaluated as an integral part of an entire flowsheet development.This communication describes the basic design features of the miniplant and some examples of applications are given.INTRODUCTIONInco operates numerous mines in Sudbury and Thompson and will shortly bring the Voisey’s Bay mine into production. It has long been recognized that the ores from different mines or from different depths of the same mine can give different responses in flotation. There is a growing need to properly evaluate the ores before feeding the mill to maximize the return of the mine/mill operation. Inco Technical Services Limited at Sheridan Park, Mississauga, Ontario has developed a batch laboratory procedure to address this issue. The results are considered in the overall economical assessment of new mine operations.For ores that cannot be processed by the existing mill operations or that will be processed by a new mill, it is necessary to develop a flowsheet that can maximize the economical return of the mine/mill operation. While recognizing the importance and contribution of the laboratory batch flotation procedure, it does not generate reliable data for flowsheet simulation and design. A full-scale pilot plant campaign is normally required to obtain the design data but often this is not possible due to a limited amount of ore obtainable from the drill core. A small-scale pilot plant (mini pilot plant or miniplant) capable of processing 20-30 kg/h ore can provide this data prior to a full-scale pilot plant campaign. A miniplant can also be used to optimize the circuit configurations, reagent additions and recycle options of process water before pilot plant work and can be used to test a different flowsheet configuration for an existing mill before re-piping a plant circuit."

Jan 1, 2003