Search Documents

By E. E. Mason

THE Myrtle group of mining claims is situated on Barkerville mountain in the Cariboo mining district of British Columbia, west of the old mining town of Barkerville. An 1,800-foot adit, known as the Shamrock tunnel, was driven in 1935-36 from the Barkerville road and in the general direction of the Myrtle group. It was proposed to enlarge this adit to more convenient section, extend it 2,500 feet int0 Myrtle ground, and from there drive a main entry 3,000 feet along the length of the group. Several laterals were also to be driven off this main entry as part of the tunnel schedule. It was thus originally proposed to drive 5,500 feet of new adit and 1,800 feet of laterals, a total of 7,300 feet of new work. Work was commenced with a bulldozer on April 21st, 1941, cutting a bench on the hillside for a plant site. The power plant was ready for operation on August 8th. Slashing and re-timbering of the old adit rook longer than was expected. It was found that 57 per cent of the length required timbering, chiefly by fore-poling, and there was also trouble in several sections with swelling ground. First round in the new face was taken on September 17th, when a 2-shift daily schedule was commenced. Due to delays in delivery of electrical equipment, it was not possible to add the third shift until November 14th. From then on, a 3-shift daily schedule was maintained with the exception of holidays and fortnightly change Sundays until August 1st, 1942, when shortage of labour caused the dropping of a shift. All work was suspended on August 14th. The ground through which the tunnel passed was such that the driving was often interrupted by the need of protective timber at the face. Further, crews were continuously employed timbering behind the face, and in maintenance of timbered sections in swelling ground. Roughly 980 feet of the new workings are now timbered, about 21 per cent of the total.

Jan 1, 1942

By Max W. Ball

THE world's largest known oil deposit lies in northern Alberta. In fact, according to government estimates, the famous so-called 'tar sands' of the Athabaska region contain several times as much oil as all the other proved reserves of the world. S. C. Ells, of the Department of Mines and Resources, who has been the Dominion Government's authority on the oil sands since 1913, has estimated the minimum content of the deposits at 100 billion barrels(!). C. P. Bowie, of the U.S. Bureau of Mines, has published an estimate of 250 billion barrels(2). ?In comparison, the latest authoritative estimate of the proved oil-field reserves of the world is less than 35 billion barrels(3). Out of this tremendous total, perhaps 500 million barrels are commercially available at present-day costs and prices; the remainder must be considered a latent reserve to be used when development costs are materially lower and petroleum prices materially higher than they now are. Mean-while, the 500-million-barrel portion presently available contains more oil than has been found in all the rest of Canada, and constitutes one of Canada's great mineral resources. Although these deposits have been known to white men since 1788, when Peter Pond, the explorer, found the Indians stewing the oil out of the sand and mixing it with spruce pitch to caulk their canoes, they are only now coming into commercial production. The purpose of the present paper is to describe the deposits, their oil content, their present development, and the possibilities that seem to lie immediately ahead. For the sake of completeness and clarity, the writer has not hesitated to use or to paraphrase material that he has previously published elsewhere in discussing various aspects of the oil sands.

Jan 1, 1941

By T. G. Joseph

"The Oil sands-Equipment Interactions Program (OsEIP) is a collaborative research venture between Syncrude Canada Ltd., James Progithin International Ltd. (JPi), the University of Alberta, P&H MinePro, and Caterpillar Inc. The objective is to better understand the behaviour of oil sands as it interacts with mining equipment, in particular, large trucks and shovels. With a move to ever larger equipment, mining oil sands of highly variable bitumen content, ground stability comes into question. This paper outlines this aspect of OsEIP and provides some insight into how some of the findings enable an improved understanding of oil sands behaviour that may impact large equipment design, operational and maintenance strategies. IntroductionThe mechanical behaviour of oil sands in the underfoot and in the face yields some of the harshest stability and digging conditions of any mining environment. High maintenance costs from truck and shovel fatigue failures predominate as a result of ground stability issues. Wear rates of shovel and dozer ground engaging tools (GET), rollers, roller paths and crusher screens result in costly and frequent replacement, or even more frequent and costly sacrificial wear zone building. From the shovel face to the crushers and screens, dry oil sands mechanics affects the degree of fragmentation and, ultimately, bitumen production.An increased knowledge of the behaviour of oil sands with respect to stability, fragmentation and abrasion, etc. would enhance the long-term equipment design process at the vendor level, and provide the end user with improved short-term operational guidelines and long-term strategies for future purchases and operation. Truck vendors recognize that the interaction between operator, seat, frame, suspension, tires and oil sands is unclear, and must be better understood before proceeding to next generation designs. Similarly for shovel manufacturers, the relationship between bucket/dipper motion, carbody, side frame, rollers, track and oil sands follow in the same vein."

Jan 1, 2002

By Guangdong Institute of Resources Comprehensive Utilization, Y. H. Tang, H. X. Hu, T. S. Dong, Z. H. Zhang

"A world class rare metals ore deposit in Africa belongs to a massive granite type poly-metallic pyrochlore-niobium resource. Successful project development in realizing the resource is vital to Africa’s economy and pyrochlore processing technology.The ore properties are quite complex due to the presence of varieties of valuable minerals, fine dissemination and intimate association of minerals and the relative abundance of easy-floatable minerals. The separation of pyrochlore from zircon, calcite and mica is generally considered difficult. Whilst studies have previously been conducted by several independent institutions overseas, no satisfactory process has yet been developed to date for the ore deposit—possibly due to the process designed being too complex; high cost of regents; lower performance.Based on process mineralogy study and extensive testwork, the authors have in recent years developed a new technology—“De-slime—Iron-rejection—Zircon (with calcite) and Calcite reverse flotation—Pyrochlore flotation”. The flow-sheet is characterized by ?1prior removal of slimes and iron minerals; ?2 Zircon (with calcite) and Calcite reverse flotation; and ?3Pyrochlore flotation applying new type of chelating collector GYX3 developed by GZRINM in conjunction with selected regulators and depressants.The process involved in the new technology is simple to implement and facilitates stable operation; the flotation reagent regime is easily adaptable; the cost of main reagent is lower largely because it is easy to manufacture and is environmental friendly. Laboratory test results demonstrated that, for raw ore assaying 0.35% Nb2O5, 0.03% Ta2O5 and 0.45% ZrO2, pyrochlore concentrate grade of >35% Nb2O5 could be obtained with >74% recovery. Meanwhile, the Ta2O5 content in pyrochlore concentrate could be recycled, and ZrO2 recovery >50% could be achieved in zircon concentrate assaying ZrO2>63%—significantly improving the technical-economic indicator. These results were verified in pilot trials of 1.44t/d throughput. The paper presents the new technology in whole, summarizes the key factors affecting its performance and discusses in simple terms the mechanism of separation."

Jan 1, 2016

By Guangdong Institute of Resources Comprehensive Utilization, Y. H. Tang, H. X. Hu, T. S. Dong, Z. H. Zhang

"A world class rare metals ore deposit in Africa belongs to a massive granite type poly-metallic pyrochlore-niobium resource. Successful project development in realizing the resource is vital to Africa’s economy and pyrochlore processing technology.The ore properties are quite complex due to the presence of varieties of valuable minerals, fine dissemination and intimate association of minerals and the relative abundance of easy-floatable minerals. The separation of pyrochlore from zircon, calcite and mica is generally considered difficult. Whilst studies have previously been conducted by several independent institutions overseas, no satisfactory process has yet been developed to date for the ore deposit—possibly due to the process designed being too complex; high cost of regents; lower performance.Based on process mineralogy study and extensive testwork, the authors have in recent years developed a new technology—“De-slime—Iron-rejection—Zircon (with calcite) and Calcite reverse flotation—Pyrochlore flotation”. The flow-sheet is characterized by ?1prior removal of slimes and iron minerals; ?2 Zircon (with calcite) and Calcite reverse flotation; and ?3Pyrochlore flotation applying new type of chelating collector GYX3 developed by GZRINM in conjunction with selected regulators and depressants.The process involved in the new technology is simple to implement and facilitates stable operation; the flotation reagent regime is easily adaptable; the cost of main reagent is lower largely because it is easy to manufacture and is environmental friendly. Laboratory test results demonstrated that, for raw ore assaying 0.35% Nb2O5, 0.03% Ta2O5 and 0.45% ZrO2, pyrochlore concentrate grade of >35% Nb2O5 could be obtained with >74% recovery. Meanwhile, the Ta2O5 content in pyrochlore concentrate could be recycled, and ZrO2 recovery >50% could be achieved in zircon concentrate assaying ZrO2>63%—significantly improving the technical-economic indicator. These results were verified in pilot trials of 1.44t/d throughput. The paper presents the new technology in whole, summarizes the key factors affecting its performance and discusses in simple terms the mechanism of separation."

Jan 1, 2016

By J B. McConnell

The Thompson smelter has three unique features which form the basis ~f its design: fluid bed roasters which treat nickel concentrate filter cake from the mill, as well as the flux, in order to achieve partial desulphurization; the use of electric furnaces for the smelting of the partially desulphurized, preheated roaster product; and the disposal of slag by water granulation and slag slurry pumping. The installation consists of three fluid bed roasters, each feeding an electric furnace. Nickel concentrate is received at the smelter via pipe line. It is thickened and filtered, and the filter cake, together with siliceous flux, is fed through rotary bin feeders and reciprocating double-gate seals into the fluid bed roasters. Air injected into the roasters through club-head tuyeres oxidizes part of the sulphur and associated iron in the concentrate. The heat of reaction dries and heats the charge. Roaster product is recovered from the gas stream in cyclones and from the roaster bed through automatic valves.

Jan 1, 1963

"The outlook for Eastern Canada is decreasing coal production over the next few years; however, a reappraisal of the long-term requirements and increased prices of coal could lead to a revitalizing of the industry. The market for Western coal is expanding and is expected to exceed 50 million tons per year in the metallurgical and thermal power fields. Western coal reserves are currently estimated at 119 billion tons. Technical developments in Eastern Canada include a shearer and gate-end support system to mechanically cut the stall and brushing at the tail-end of a longwall. In Western Canada, the most modern equipment is used in mining, beneficiating and shipping coal. Results to date on the underground hydraulic experiments exceed expectations. The importance of reclamation is recognized and plans have been made to restore and re-vegetate disturbed areas and mine dumps. In Eastern Canada, experiments were started to determine the feasibility of coal reclamation from mine dumps, including one dump that is on fire. The Mining Research Centre, Mines Branch, continued to conduct research work oriented toward solving Canadian mining problems The Western office of the Centre, opened in 1970, was set up primarily to study problems associated with a resurgent coal industry."

Jan 1, 1971

By J. Chlopas, D. J. Barratt, M. V. Sharp

"This paper describes the modifications made to the Fox Mine copper concentrate bin in order to obtain a continuous flow condition. The design of these modifications is based on test results obtained on Fox Mine concentrate using the flow factor testing machine in the research facilities of Cominco at Trail, B.C.The original design consisted of a cylindrical steel bin on a concrete slab with two slot-discharge openings. Based on predictions of the maximum mass flow hopper angle for conical and wedge shaped hoppers for the concentrate on various potential bin lining materials, Ultra-High Molecular Weight (UHMW) Polymer was selected as a liner.Using the recommended angles for conical and wedge shaped hoppers, the profile of the bin base was changed to suit the existing slot openings.The initial method of fastening the liner resulted in failure of the connections. Subsequent modification to the zinc concentrate bin fastener system proved satisfactory and it has now been in operation for over one year without any separation of the lining material.Utilization of flow testing procedures on concentrate samples has demonstrated that proper design of storage bins or hoppers to achieve continuous flow can be incorporated into the design of new plants."

Jan 1, 1978

By S. Ianos, C. Vibert

Type and shape of large dams founded on rock depend upon the expected deformation of their foundation. Their design consequently requires the assessment of the deformability of the rock mass at large scale. Seismic refraction, laboratory tests on rock samples and empirical formulas can provide an order of magnitude of the deformation modulus, with a limited degree of reliability. Direct in-situ measurement of the deformability of a volume of rock is therefore preferred, which integrate the effect of discontinuities, such as plate loading tests, dilatometric tests, etc. The authors have been compiling results obtained by in-situ deformability tests on a number of dam sites, including the Scarabée (“Petite Sismique”) method. This last method consists in thoroughly analysing the shape of seismic wave forms transmitted through the rock mass. It has been used since now more than 40 years over a large number of dam foundations, and has proved to provide a satisfactory assessment of the static deformation modulus. After comparing the results obtained from different methods on six dam sites, the Authors conclude that their reliability closely depends upon the size of the loading device in relation to the spacing of the discontinuities. Attempts to correlate results from different types of in-situ loading tests reveal difficult, because closely depending upon local geotechnical conditions at test location. Plate jacking tests appear to be the most reliable, because involving a relatively large volume of rock. On the other hand, the Scarabée method (“Petite Sismique”) allows a rapid assessment of the deformation characteristics of the rock mass at large scale, and has been found to provide values generally in agreement with those from plate loading tests, while dilatometric or flat-jack tests were found too dependent upon local conditions. The Authors conclude that preference should be given first to the Scarabée method, which uses light equipment and is quickly performed, together with an accurate geological and geotechnical assessment for interpretation. In a second stage, Scarabée shall be complemented by adequately performed plate jacking tests in selected locations, in order to cross-check results and refine the assessment. The general accordance between the results of the two methods, which both can integrate anisotropy of rock masses, justifies this statement.

Jan 1, 2015

By L. X. Li

Coking coal producers often encounter variations in clean coal quality when mining multiseam deposits containing coals with different washability and coking properties. This paper describes how, for a single coal property, an initial clean coal specification with an ash content of 8.5% on an air-dried basis (ADB) and a free swelling index (FSI) of 5.5 can be improved to a specification with 7.5% ash content ADB and an FSI of 6. This is accomplished by sorting coal seams into two groups for processing and blending. A preliminary economic model demonstrates how this improvement enhances economic returns through a beneficial factor.

Jan 1, 2014

By L. V. Chugaev, Y. M. Shneerson, P. V. Zaytsev, I. V. Fomenko, M. A. Pleshkov

"Pressure oxidation (POX) is one of the most common and reliable methods of processing gold-bearing sulfide concentrates. However, when processing concentrates that contain natural carbonaceous matter, substantial gold losses occur due to autoclave preg-robbing. The latter involves formation of gold chloride complexes under typical POX conditions (high temperatures, high acidity and high ORP) and subsequent sorption of these complexes by carbonaceous matter. Naturally, chloride ion plays a significant role in the process of autoclave preg-robbing; its concentration in POX solution has a well-marked effect on subsequent gold recovery during cyanidation of POX residue. The previous research done by SRC Hydrometallurgy showed that autoclave preg-robbing of gold could be significantly inhibited by the addition of mercury(II) compounds to POX slurry. The positive effect of mercury(II) was well pronounced both at high (>20 mg/L) and low (<5 mg/L) Cl concentrations in POX solution. The successful bench-scale laboratory testing was followed by pilot plant trials at Ore Test Facility in Blagoveshchensk, Russia. The present paper provides the results of these trials. The bench-scale testing results were verified; the optimum oxidizing parameters and reagent dosage were specified. The behavior of mercury (II) at POX pilot plant was found to be in good consistency with industrial practice described in the literature.INTRODUCTION Pressure oxidation (POX) is one of the most common, reliable, and commercially proven methods of processing gold-bearing sulfide ores and concentrates. However, when processing double refractory materials that contain natural carbonaceous matter, POX technology advantages are compromised by autoclave preg-robbing of gold. The latter occurs when natural organic carbon and soluble halides are both present in autoclave feed. Strongly oxidizing conditions of POX (high temperature, oxidation-reduction potential or ORP, and acidity) favor formation of gold-halide (mostly, gold-chloride) complexes, which tend to bond with carbonaceous matter. The exact nature and mechanism of this bonding is unknown, but as the result of this, cyanide is unable to leach gold from POX residue and the precious metal is lost to the tails (Axenov et al., 2014; Dimov, Chryssoulis, & Sodhi, 2003; Fomenko, Zaytsev, Pleshkov, Chugaev, & Shneerson, 2013)."

Jan 1, 2017

By Joseph J. Larry

In hard siliceous sandstone strata overlying coal seams, roof bolting is often the bottleneck in the coal production cycle. In the past, these strata have been drilled by pneumatically operated stopers. Although slow drilling is cumbersome and uncomfortably noisy, the stoper was the most effective drill in these harder strata. However, because of the (U.S.) Coal Mining Safety Act, which limits noise levels for operating drills, FMC Mining Equipment developed the water-through-the-drill-steel method of drilling high-compressive-strength strata. Although water-through-the-drill steel had been developed earlier, the real impact of wet drilling techniques surfaced when the dual-boom roof drilling machines were installed at the Virginia-Pocahontas Division, Keen Mountain, Virginia, in 1974. This paper covers some of the technical details of the water-through- the-drill-steel design and its application.

Jan 1, 1979

By \/eena Sahajwalla, Jonathan Dicker, Paul O'Kane, Cath Skidmore, James Dankwah, Magdalena Zaharia, Rita Khanna, David Knights, N Saha-Chaudhury, Somyote Kongkarat

Due to the inherent limitations of current methods of disposal of end of life polymeric materials, avenues are researched towards developing alternative, environmentally friendly and economic recycling processes. Different polymeric materials (i.e. rubber, high density polyethylene (HDPE) and polyethylene therephtalate (PET)), quite distinct in terms of chemical structure and composition, were considered in the present study as carbon resources in EAF steelmaking. Investigations were conducted in both laboratory and industrial scale steelmaking to assess the effectiveness of using these materials as carbon sources for slag foaming in EAF steelmaking. Slag foaming is important because it enhances furnace efficiency.

Jan 1, 2011

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he&apos;s hurt. Maybe he&apos;s not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

Oct 1, 2010

By Charles G. Kemsley

MR. C. R. WHITTEMORE: It is interesting to note that the mining industry is making increased use of alloy steels for drilling. They will undoubtedly lead to greater footage at lesser cost. Mr. Kemsley states that, for use in hard ground, the shanks are brought to a hardness of 435 to 440 Brinell by heating them to approximately l,800°F. It seems to me that this temperature is excessively high-it is considerably above the critical point of the steel. The only effect of such a high temperature is to lessen considerably the impact resistance of the steel. The possibilities of an oil quench, followed by a tempering draw which does not lessen the hardness of the steel too much but increases its toughness, might well repay further study; also the temperature control, a factor which depends on the composition of the steel. However, service results are undoubtedly the best criterion of practice. MR. KEMSLEY: I would like to point out that the steel is not quenched at 1,800°F. After heating to this temperature, it is laid aside to cool gradually; this high temperature is necessary to produce the required hardness by simple normalizing-cooling in still air. We all know that ideal conditions for hardening steel demand salt baths and furnaces with automatic temperature control, but for most companies the cost of such equipment having sufficient output capacity is prohibitive. The end we are trying to attain is to make good drills at a cost that will be within the means of any mine.

Jan 1, 1942

By R. P. Chapman

The geochemical interpretation of results of statistical analysis of published multi-element stream sediment data from southwest and northern New Brunswick is presented. Element concentrations in southwest New Brunswick are low and comparable to element concentrations in background areas in northern New Brunswick. Deposits of copper and nickel are indicated in southwest New Brunswick. Anomalous element concentrations occur in several areas in northern New Brunswick and the elements most commonly associated with these anomalies are Cu, Pb, Zn, As and Ag; and also Mo, Wand Sb. Bedrock geology greatly influences element concentrations and may cause false anomalies. Manganese has a pronounced effect on the dispersion patterns of Co and also Zn, Mo, Pb, As, Ba and Ni. Nickel and Cr are strongly sympathetically related and this association is independent of bedrock type.

Jan 1, 1977

By B. R. Boardman

Project Environmental Approval is a multi-faceted issue. From a mining perspective, it is a costly item because of avoidable time delay. The government perspective is that the approvals are a necessary part of meeting departmental requirements to ensure that the wellbeing of other uses of the environment is maintained. This paper outlines some of the problems inherent in the environmental approvals process and makes recommendations to both the proponent and government about improving the efficiency of the process.

Jan 1, 1978

By Hu Harries

WE RECENTLY completed a study for a client, who is an applicant to export gas from the Province of Alberta, on the effects of gas export on Alberta&apos;s economy. This study was part of the client&apos;s application ?before the Conservation Board, and, no doubt, some of you are familiar with it. Submissions by other applicants in earlier hearings before the Board and before the Royal Commission on Energy, as well as claims made by parties opposing export, have also brought forward a number of other opmwns regarding possible economic effects. Ali of these studies have been on a piecemeal basis. They have dealt with particular aspects of particular applications, and only indirectly and by inference with the overall question of gas ex-port. We have prepared this paper to review the overall picture and ex-amine, as far as time permits, all sides of the question. While the paper is entitled Economic Effects of Gas Export on Alberta, we felt that the area considered should in-elude northeastern British Columbia, not only because Westcoast, the first major gas export project, is essentially a northeastern B. C. project, but because this area has historically been, from the point of view of economic, if not of political, geography, part of Alberta. In this paper, when we talk of export, we mean export from the Province or, in this case, from Alberta plus northeastern B. C. Sales to other parts of Canada have exactly the same effect on the economy of this area as l1ave sales to the United States, provided, of course, they are made on equal terms.

Jan 1, 1958

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By B. R. MacKay

Introduction The Corbin coalfield is one of the smallest, and at the same time one of the principal, producing bituminous-coal areas in southeastern British Columbia, and is unique on account of the great original thickness of one of its coal seams and the remarkable concentration of coal in a small area that has occurred through intense folding and faulting of the measures. These are such that the deposit has been referred to at times as "the world&apos;s thickest coal seam" and as" a mountain of coal." The determination of the number, thickness, and character of the seams present, and the structure, extent, and geological relationship of the several deposits, are of vital interest both to the operating company in its endeavour to evolve the most efficient method of mining these exceptionally thick deposits and to the Government in estimating the coal resources of the different fields. With the object of ascertaining these data the writer was assigned in 1930 to geologically map and study the Corbin coal deposit. A topographic map covering Coal mountain and the immediate vicinity on a scale of 1 inch =800 feet, with a contour interval of 25 feet, made by the Topographic Division of the Geological Survey, served as the base for the geological mapping.

Jan 1, 1931