Search Documents

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,' or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

By A. V. De Forest

INSPECTION and test methods of great diversity have been used from the most ancient times to select raw material, control its manufacture, and appraise its finished properties and value. The "miller thumb," expert in grading flour, the vintner's sense of taste, the goldsmith's micro-wear test on a touchstone, the enquiring sniff over the doubtful egg -these are all nondestructive inspection methods, accurate and depend- able, but not readily reduced to numbers in the c.g.s. system. A horse trader inspecting a possible purchase is interested in more than age, size, weight, color. heredity, speed, or drawbar pull which can be reduced to figures. Behavior, temperament, stamina, health-past, present and future---are just as important as the numerically determinate constants.

Jan 1, 1940

By JOHN JANNEY

STABILIZATION of the adjustment of normal consumption to normal production of world commodities is quite different from reducing production until visible surpluses are consumed. The first means restoration and maintenance of prosperity, the second means merely a temporary alleviation of a condition with the prime cause remaining uncorrected. Overproduction of foodstuffs in some sections of the world while millions starve in other sections represents not so much overproduction of foodstuffs as mal-distribution of foodstuffs. The flour mills of Washington and Oregon normally ship quantities of flour to China. Now, the wheat that would make this flour goes East instead of West. Is this overproduction, or is there something wrong that calls for study, analysis and correction? Can the plan used by the ostrich of hiding its head in. the sand get us by this present world tragedy, or must the challenge to solve this problem be met, constructively? Can we not make out of this breakdown in the world's economic system an opportunity? And use it as the stimulus for remedying the basic cause of the trouble and not content ourselves with devising temporary expedients that aim at remedying this or that of the obvious conditions, in themselves not causes at all but rather the evidence of causes, or that are the symptoms of the real trouble.

Jan 1, 1931

By Herty, C. H.

The effect of temperature on the physical properties of structural materials has been the subject of many investigations during the past decade. The literature on the effect of elevated temperatures. is voluminous, and during the last four years a great deal of experimental work has been carried out on the effect of low temperatures on the impact properties of steel. For many engineering purposes it is important to know the shock resistance of steels at low atmospheric temperatures, and with the ever-developing field of refrigeration and separation of materials at low temperatures, the normal limits of atmospheric temperature have been exceeded in practice. Iron and its alloys in the unnotched condition have a high impact strength at low temperatures, but in practice variations in type of notches result either from design or accidentally through scratches and surface or internal defects. A study of notched bar impact tests is, therefore, highly important to the engineer. A survey of the literature on low temperature impact testing indicates that chemical composition, heat treatment and method of testing have been the variables which have been considered in most previous work. In only a few instances has any mention of the steel- making method been mentioned and in these the comparison was between steel-making processes and not between steel-making methods on the same process. In view of the wide variations in impact properties at room temperature, in quench and strain ageing and in grain growth of steels of identical chemical composition, (by this is meant the usual five element analysis reported), it was felt

Jan 1, 1957

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

By W. A. Scheuch

ORDINARILY secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product.

Jan 1, 1929

By E. H. T. Whitten

Fundamental principles of trend surface analysis are briefly reviewed. Recent analyses of several granite masses illustrate the method of estimating the quantitative regional composition and also variation trends. Mineralogi-cal, bulk chemical, and other quantitative variates can be employed. Such results should improve gravimetric surveys (etc.) relying on correction terms based upon estimated rock composition. For the first time realistic estimates of the mean composition of rock bodies can be made with the aid of trend components. Deviation maps hold promise for delimitation of disseminated mineralized areas. Deviations comprise residual "anomalies" after removal of trend components. In petrogenetic work such deviations have been shown to reflect local influences (e.g., contamination of magma by assimilation of xenoliths or country rocks of the envelope). Similarly, mineralization should be reflected as deviations standing out from background trends. Actual examples are given. Present results largely involved projection of data onto a horizontal plane, but if sufficient data are available use of three spatial coordinates increases accuracy for prediction in "unexposed" areas. Regression analysis shows that statistical correlations between variates for regionally distributed specimens are often strong (particularly with percentage data). Hence, in preliminary surveys more easily determined variates may sometimes be employed to gain first estimates of the distribution of components more economically significant. The sampling plan is of paramount importance. Unless a suitable sampling plan is devised and adhered to rigorously during collection of the samples, all subsequent analysis is liable to strong bias and to yield spurious estimates of the truth. For a wide variety of purposes it is becoming necessary to assess the quantitative composition and variability of rock masses and mineralized zones of various types. In petrology and petrography this is something of a break with tradition, because virtually all descriptions heretofore have been qualitative. Although vast amounts of qualitative data have been compiled, little is known about the quantitative behavior of rock components. However, if variability of rocks could be understood and expressed with sufficient accuracy, there would be considerable advantage to both economic and petrogenetic problems. For example, if, on the basis of a limited series of observations, the three-dimensional geometry of a disseminated orebody (or ore-bearing formation) could be predicted accurately, it would be possible to extrapolate with confidence the structure into unexposed areas. The following example based upon the geometry of an igneous cone sheet illustrates the point. The significant rock-unit gives outcrops at a number of points on the exposed surface ABCD (Fig. 1A). Study of n exposures may enable a geologist to predict that the rock-unit is circular in form and thus indicate where the unit can be expected in unexposed terrain. Such observations are made at sites with u, v coordinates, but, if subsurface information is available at sites with uvw coordinates, it will eventually become possible to predict accurately the three-dimensional form of the rock mass. Geologic rock masses or mineral deposits are not generally as regular and symmetrical in geometric form as the body illustrated in Fig. 1A. However, even where the broad limits of a major rock mass are known, a more acute problem arises in attempting to obtain detailed quantitative estimates of its internal variability; it is difficult to predict the variability of a mass from a limited number of observa-

Jan 1, 1961

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

By C. Feng, C. Elbaum

Knoop hardness measurements were carried out on large grains of iodide titanium containing different amounts of oxygen. For each oxygen content the hardness is recorded ainingas a function of the crystal orientation and of the angle 4 between the indenter diagonal and the projection of the C (hexad) axis in the surface. The results can be expressed by the following relation; hardness = n-k cos 2ø, where n and k are constants for a given oxygen content and crystal surface orientation. A NISOTROPY of hardness is a well-known phe-nomenon and has been reported for many metals.1-3 At the present time, however, such information is not available in the literature for titanium. Consequently, a systematic study of the simultaneous effects of oxygen content and crystallographic orientation on the hardness of titanium was undertaken in this laboratory. Evaluations of oxygen content in titanium are frequently carried out through hardness tests. Although such procedures may be justified in small grain specimens, the results of the present investigation indicate that the anisotropy of hardness should be taken into account in the case of coarsegrained specimens as well as in the case of pronounced preferred orientation. Materials and Experimental Procedures Iodide titanium, 99.99 pet pure and containing of the order of 0.002 wt pet O, was used throughout this investigation. The metal was arc melted in an argon atmosphere and cold rolled into strips 1/16 in. thick. These strips were subsequently recrystal-lized and strain annealed in vacuum (10" mm Hg or better) at 850°C in order to produce crystals varying in diameter from 10 to 25 mm. Oxygen was introduced into selected large crystals by heating at 700°C in an atmosphere of pure oxygen under an observed pressure of approximately 50 mm Hg. Each sample was subsequently annealed in vacuum at 850°C for 100 hr, in order to homogenize the oxygen content throughout the specimen. It was found that longer annealing was not necessary, for no change of surface hardness in a given direction was detected after prolonged annealing. The oxygen content was determined by the difference in weight of the specimens before and after the oxidation-annealing cycle. The accuracy of oxygen determination is within ±0.1 mg in samples weighing 0.5 to 1 g. A vacuum fusion analysis of oxygen was performed on several samples and gave results in good agreement with the ones obtained by the weight change. It should be emphasized that expected weight losses through evaporation of the metal in vacuum at 850°C' are many orders of magnitude lower than the precision of these measurements. Following the annealing treatment, both oxidized and unoxidized crystals were carefully polished. All detectable traces of surface cold working were removed by repeated polishing and etching. Laue back reflection X-ray patterns were taken for each crystal for the purpose of determining the orientation and ascertaining the absence of substructures detectable by this method. Hardness measurements, using a 1 kg load, were subsequently carried out on a Tukon hardness tester equipped with a Knoop indenter. The Knoop indenter was used throughout this work because indentations obtained by means of a Vickers indenter are considerably distorted due to the anisotropy of the elastic constants in titanium. Such distortions are much less pronounced in the case of Knoop indentations, although for some orientations a cer-

Jan 1, 1959

Beyer Barometric Condenser The Ingersoll-Rand Co. is now offering to the trade complete steam­condensing plants for all service conditions. This equipment includes the Beyer barometric condenser, for' which the company has secured the patent rights, Imperial duplex and Ingersoll-Rogler straight-line reciprocating dry vacuum pumps and, where required, Cameron simplex and centrifugal pumps. The Beyer barometric condenser is of the counter-current type, in which air and cooling water flow in opposite directions. The steam inlet is at the bottom of the condensing v el, the water inlet above and the air-removal opening at the top. The sheets of cooling water over owing the pool at the inlet point meet the entering steam. The two are brought into intimate contact by conical baffle plates which assist the water to absorb to its full capacity the latent heat of the steam. The non-condensable air liberated in the condensing action rises through the falling water to the removal point at the top, being cooled to practically the temperature of the incoming water. It is also to be noted that ample opportunity is given for the removal of the air content of the water before

Jan 8, 1916

By Cadwallader Evans

MY endeavor in this paper will be to tell something of the accomplishments and current problems of the anthracite producer and to suggest some of the avenues for technical development that seem to me to be the most necessary and likely to bear fruitful results. The several subjects, that I find of most interest will be taken up individually with brief reference to the future trend. Underground Mining and Loading ?In this field great progress has been made in the last twenty years, beginning with the introduction of the scraper system. The electrical hoists for the operation of scrapers have been improved, and give little trouble, but there is an open field for the improvement of the auxiliary apparatus, particularly in the application of roller-hearing sheaves to the guiding of scraper ropes. Also notable in the last six or seven years is the introduction of shaker chutes, so that far more anthracite is now loaded over them than by scrapers. This trend should continue to be manifest, particularly if those who are looking ahead and who are charged with the development of this specialty continue constantly to study and improve the mechanical design of their shakers.

Jan 1, 1938

By EDWARD B. DURHAH

(San Francisco Meeting, UCtober, 1911.) THE refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying more than 200 parts of precious metals in 1000, or, in mint parlance; over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum group that were in the bullion. This residue is relatively small, and is melted into bars and stored until sufficient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's office, laboratory, and generator-room, respectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Oct 1, 1911

By Ernst M. Cohn

The demonstrations of the "Silent Sentry" by Union Carbide Corp. in 1957 and of a special tractor-plow by Allis-Chalmers in 1959 ushered in the technology era of fuel cells. The idea for direct conversion of chemical to electrical energy, first published in 1801 by Davy in England and Ritter in Germany, has been kept alive by a few people through 150 years: Grove built the first hydrogen-oxygen fuel cell in 1839; Mond and Langer made electrolyte contributions around 1890 that are still used today; Baur worked on coal-based cells from 1900; Bacon started his work in the '30's, which resulted in the first multi-kilowatt unit in the '50's; Davtyan studied molten-salt electrolytes in the '40's, followed by Ketelaar in the '50's; and Justi developed highly active electrodes in the '50's, to name only some of the pioneers. Despite the tremendous increase in research and development of fuel cells, these direct energy converters are still in their infancy. They will find their functional application in space, where power density must be maximized and product water utilized. These early systems will provide valuable experience in system engineering and reliability.

Jan 9, 1964

Jan 1, 1969

By Carl Heinrich

I HAVE read with particular interest that portion of the discussion by Anton Eilers referring to the high-lime (and also high-alumina) slags made by August Raht in 1881, while smelting the Horn Silver ores at Franklin, Utah. The two analyses of such slags, furnished by Mr. Raht to Mr. Eilers are: Horn Silver Slags Oxygen(b) Oxygen(b) Average of I and. II Slag I percentage Slag II percentage Oxygen Si02 33.9 18.1 .35.0 18.7 34.50 18.40 FeO 26.8 6.0 25.4 5.7 26.10 5.80 CaO 26.1 7.5 24.9 7.1 25.50 7.30 BaO 3.2 (a) 0.3 3.2 0.3 3.20 0.30 A1203 10.8 5.1 9.3 4.4. 10.05 4.75 100.8 37.0 97.8 36.2

Jan 10, 1916

By Marvin P. Barnes, John G. Simos

The Park City District, Utah, is situated in the Wasatch Range at the intersection of the westward extension of the axis of the Uinta Range. Ore has been mined almost continuously from the first discovery in 1869 to the present day, with a total production of over 14 million tons. Sediments of Carboniferous to Triassic age have been folded into the northerly plunging Park City anticline and subsequently modified by thrust faulting, diorite and diorite porphyry intrusions, and strong east-west normal faulting during the Laramide orogeny. Younger andesitic volcanics partially cover the eastern edge of the district. The ore bodies occur as both lode and bedded replacement deposits over widely scattered localities. Near surface, high-grade silver "bonanza" ores were mined in early days from the Ontario and Daly Lodes, which occur along the east-west zone of faulting near the center of the district. Other lode or fissure deposits were found along the Mayflower and Hawkeye faults to the east and southeast. Large bedded replacement silver-lead-zinc ore bodies associated with east-west zones of fissuring, have been mined from favorable horizons in the Park City Formation in the Daly West and Judge mines. A series of long, narrow, high-grade, replacement ore bodies occur in the Silver King mine at a single horizon in the Park City Formation. Ore is currently being mined from strong bedded replacements in the Humbug Formation near the apex of the Park City anticline. Factors controlling ore deposition are: magmatic source, structural feeder systems, and favorable host rocks. Ore deposition along favorable beds is primarily a function of physical conditioning and secondarily of chemical composition.

Jan 1, 1968

Large deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the .manganese content of manganiferous iron ores in a form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports.' The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treatment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a 1/2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930