Search Documents

In coal mining, geophysical techniques have an established application in determining the location of seam boundaries ahead of the face so that underground mines can be planned to avoid any geological structures that might disrupt production. Geophysics can also be used in geotechnical studies to determine the in situ properties of the rock mass and the response of the rock mass to the mining. The use of geophysical logs and microseismic monitoring in these geotechnical applications are discussed in this paper.

Jan 1, 2002

By A G. Cuison, B V. Andam

Three well-known copper and gold deposits in northern Luzon, Philippines are located in the Mankayan Mineral District. These are the Lepanto Copper-Gold Deposit, the Far Southeast Porphyry Copper Deposit and the newly discovered Victoria Gold Deposit. The latter discovery led LCMC to shift from a predominantly copper mine to a gold mine. The pre-Eocene Lepanto basement andesite and the middle Miocene Balili volcaniclastic sequence underlie the Mankayan Mineral District. They are intruded by tonalitic to gabbroic Bagon Intrusive followed by diorite-quartz diorite intrusions. Diatreme emplacement of late Miocene-early Pliocene Imbanguila dacite pyroclastics and porphyries took place much later. Faults in the district mostly form a conjugate fracture pattern dominated by north and northwest trending shears, east-west trending extensional fractures and few north-south trending fissures. Victoria is an epithermal gold-base metal rich quartz vein deposit. The veins occur along tensional structures and it is common to observe crustiform and banded features among the sulphides and gangue minerals. It is an open space infilling type of mineralisation. The Victoria vein systems are divided into zones based on continuity. In each zone are major veins and associated spits. Dacite pyroclastics and porphyries predominantly host the major veins with a few narrow veins hosted by the Balili volcaniclastics and the Lepanto metavolcanics. The veins generally trend east-northeast with 75 - 80 dips towards the south. The longest vein can be traced fairly continuously for a horizontal distance of about 600 metres. The vertical persistence of major veins exposed on three level drives has a range of 150 metres and can reach as much as 400 metres based on drill hole intercepts. The vein widths vary from two to eight metres. Right lateral movements of either the NW or NE shear faults could have produced the east trending tensional fractures. The development of ore shoot patterns was recognised and has been helpful to the mining operations. Cymoid loops with defined pinch and swell features are noted both laterally and vertically. Complementing the structural pattern is the distribution of gold values along veins where lateral and vertical continuity is also observed. Gold is associated with quartz, sphalerite, galena and chalcopyrite. In relatively high gold zones, the abundant sulphides are sphalerite and galena. In relatively high copper zones, there is an abundance of chalcopyrite and tetrahedrite. Galena is always associated with sphalerite but less in abundance. Chalcopyrite occurs either as separate bands from or associated with sphalerite-galena. Chalcopyrite and tetrahedrite appears contemporaneous with sphalerite and galena but in some portions the former cuts the latter sulphides. The predominant gangue minerals are quartz, carbonates and gypsum. Rhodochrosite is the predominant carbonate gangue. Few sulphides are found in the carbonates. Gypsum (anhydrite) is found cross-cutting early mineralisation. It carries very few sulphides. The alteration halos around veins are relatively narrow. In an outward sequence, the silicic alteration occurs very near the veins, followed by sericitic-argillic alteration then to propylitic zones. It is also common to observe veins bounded by propylitic alteration. Preliminary paragenetic studies show apparent three stages of mineralisation, the early-quartz (-gold) stage followed by a carbonate stage and a late-gypsum stage. The abundance of base metals relatively decreases towards the gypsum stage. The Victoria gold deposit could have some genetic associations with the Lepanto Cu-Au deposit and probably indirectly with the FSE porphyry system. It is relatively apparent that the Victoria quartz-gold-base metal veins could have occurred similarly as the quartz-gold roots overprinting the Lepanto enargite mineralisation. This overprinting signifies the waning stages of the entire hydrothermal system.

Jan 1, 1999

By Ioannis K. Kapageridis

The lignite deposits of the Kozani-Ptolemais-Amyntaio basin in western Macedonia (North-West Greece) present a difficult modelling problem. Each deposit consists of several thin lignite layers ranging from a few centimetres to a few tens of centimeters in thickness, and thin intercalated sterile layers of marly limestones, marls, clays, and sands. These layers are practically impossible to model individually due to fast lateral transition of lignite layers to humus clay and vice versa and the lack of reliable and detailed stratigraphic correlation, leading to compositing methods being applied prior to any interpolation and modelling. The complexity of the deposit is further increased by the presence of a number of faults. This paper presents the modelling and estimation procedures applied during the most recent study of the South Western Field ? a new deposit that is considered for development and lignite production over the next years and will support the operation of a new power station in the area. Special focus is given to drillhole database structuring, fault modelling, stratigraphic correlation, mineable lignite intervals compositing, and resource estimation. The use of specialised mine planning software in all stages of modelling and estimation is thoroughly explained.

Oct 1, 2009

By Jim Dodd, Jim Paynter

"We would like to acknowledge the efforts of the following key people who helped to make this project a success.Ron Jung, instrumentation supervisor for the Golden Giant Mine, spent many hours reviewing process and instrument drawings, selecting instruments and providing hands on support during commissioning.Andy Keough, underground production supervisor for the Golden Giant Mine, was responsible for readying the underground distribution network for paste backfill.H.A. Simons Ltd. personnel who did an excellent job providing sound conceptual and detailed engineering.Fred Brackebusch, of Mine System Design who designed the paste backfill delivery systemPierre Lacombe, mill superintendent of the Louvicourt Mine, generously shared information and operating experience of their paste backfill plant.AbstractThroughout the 11 year history of the Golden Giant Mine, the primary backfilling method made use of consolidated rock fill. New backfill technologies have developed over recent years which now make it possible to use large quantities of fine mill tailings as backfill.In January of 1996, construction began on a new paste backfill plant at the Golden Giant Mine. Six months following, the plant was commissioned. This paper describes the design, commissioning and operational experience to date of the paste backfill plant."

Jan 1, 1997

By J. Eriksson

Slag from stainless steelmaking is known to disintegrate, which is an environmental problem and prevents the cooled slag from being utilized. This disintegration is due to the transformation from the ßto the ? polymorph of di-calcium silicate. The transformation is accompanied by an increase in volume of about 11% and a total disintegration of the slag. AOD slag from stainless steelmaking was re-melted in a laboratory induction furnace, together with olivine and calcinated dolomite, to investigate the prevention of disintegration by increased MgO content of the slag with small changes in CaO to SiO2ratio. The modified slag was examined with X-ray diffraction and scanning electron microscopy. The trials showed that an increased MgO content can change the mineral composition towards formation of more Merwinite and Bredigite, which prevents disintegration of the slag. Keywords: slag, disintegration, di-calcium silicate

Jan 1, 2004

By Richard R. Marston, Scott Herr, Steve Pries, Donald L. Jr Ewart

The purpose of this paper is to identify and examine alternative methods (other than shovel/truck stripping) of effecting the pre-stripping of consolidated overburden, in conjunction with dragline stripping operations, at surface coal mines. The analysis will be case study oriented with practical mining considerations and comparative economics being evaluated. Alternatives that will be examined include blast casting, dozer push, and multiple pass dragline sequences.

Jan 1, 1992

Suddenly, mining has been thrust into the limelight. It has a large image that casts its shadow over New Zealand. Is it any wonder that resistance has heightened and that an almost unprepared populous is currently struggling to protect the very land they hold dear. Next to the atomic bomb, mining has the demonstrated power to massively change the land and its side effects can pollute many miles beyond the operation. During the past year, New Zealand concern over the possible effects of the mining proposals has become acute. This was specially so in the areas of special environmental quality, such as the Coromandel, and here a very unhappy situation has arisen.

Jan 1, 1981

By Craig M. Sams

"Variable speed mill popularity has grown during the last 10 years with almost every SAG mill fitted with a variable speed drive. In addition, many of today’s larger ball mills are running a variable speed drive for various reasons. In the past, motor suppliers, especially gearless drive suppliers, have considered mills as being an overpriced rotor. This has lead to mills demanding more torque than what a motor can generate. This paper identifies the reasoning of what has happened and how to mitigate the mismatch in the future. Technical and economical issues are discussed, allowing mill operators to make an informed decision of which path to take in deciding what motor to put on a mill.INTRODUCTIONIt has been generally accepted in the past that motor suppliers and specialists in engineering companies understand the workings of a SAG mill or a ball mill and although there is a fair knowledge within the industry, in regards to mill torque requirements, the advent of variable speed drives in ball mills has shown the writer that a complete understanding of the mill torque requirements are not fully understood.This paper will discuss two aspects of mill torque requirements, (operating torque at various charge levels and start up torque), and how it relates to specifying the proper motor torque requirements.MILL OPERATING TORQUEMill operating torque at a given charge level and density in a mill is essentially constant throughout the entire speed range. For the purpose of this paper, we will take a 38’x 22.5’, 20’ EGL, SAG mill and provide the power draw at variable speeds but fixed loading conditions.The power draw and mill torque of this mill at 8% ball charge and 28% total loading (Highlighted) is shown below as Figure 1, at variable speeds."

Jan 1, 2007

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By Deane Tunaley, Clint Brearley, Steven Kotsonis, Richard Goodridge, Tom Smylie

Explosives are widely used in the Oil & Gas Industry for subsurface mapping via measurement of reflected sound waves as each charge is detonated. To complete a seismic survey, several thousand explosive charges may be deployed into narrow boreholes, often in areas difficult to access or where socio-political factors may increase the risk of unlawful recovery or sabotage of the explosives. Therefore, when misfires occur, the explosives left in the ground often cannot be retrieved or sympathetically detonated safely, in which case they are “abandoned” (in-line with local regulations) potentially posing a safety and security risk.

Jan 1, 2014

By Bruce Hebblewhite

Australia’s Minerals Tertiary Education Council (MTEC) has achieved several successes during its first three years of operation. This initiative was developed through the Minerals Council of Australia, in conjunction with three partner universities involved in mining engineering education. The partner universities are the University of New South Wales (UNSW); Curtin University, the West Australian School of Mines (WASM); and the University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and the development of a number of flexible, distance-based delivery programs. This article then discusses future initiatives. Importantly, the challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering: Mining Education Australia (MEA). This will provide a common third and fourth year program to all three universities beginning in 2007. The common program will involve innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process.

Jan 1, 2006

By T. G. Donnelly

This final report summarizes the prototype development and testing of an air curtain respirotory protective device under Bureau of Mines Contract HO122087. The air curtain respiratory protective device, as part of a miner?s hat, provides protection for the underground mining machine operator against inhalation of dangerous amounts of respirable coal dust. Major components of the air curtain respiratory protective device are: 1) a modified miner hat incorporating an air curtain jet manifold from which the protective air curtain emanates, 2) a motor blower which supplies the air for the air curtain, 3) a filter element to remove the particulate material from the air used for the air curtain, and 4) the hoses and coupling used to duct the filtered air from the motor blower to the modified miner's hat.

Jan 1, 1973

By Stafford McKnight, Larissa Koroznikova, Steve Hall, Cameron Klutke

This paper outlines a simple methodology for mineral characterisation, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterisation of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used, however this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900?s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterisation of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4 ? 4.7 and zircon RD 4.6 ? 4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150 microns). The developing methodology that can achieve low-cost, low toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By S Colak, M Tunc, C Celik, M. M. Kocakerim

The most important parameters affecting the solubility of ulexite (sodium calcium borate) in H2SO4 were found to be reaction temperature and solid:liquid ratio, in that order. Dissolution increased with increase in temperature and stirring speed and with decrease in solid:liquid ratio, particle size and acid concentration, the last effect as a result of decreased precipitation of CaSO4 on unreacted particles. Optimum conditions, in which around 99.5% of the ulexite could be dissolved, were a reaction temperature of 60 degrees C, a solid:liquid ratio of 1:8 g/ml, an acid concentration of 8 mol/l, particle size smaller than 425 micrometres, a stirring speed of 52.33/s, a reaction time of 1 800 s, a calcining time of 3 600 s and a calcining temperature of 170 degrees C. These conditions, determined by the Taguchi method, are reproducible in a commercial production environment

Jun 21, 1905

By L Forrester

The tube bundle system is an integral part of an underground coalmine’s gas monitoring system. The maintenance of these systems is vital to ensure the quality of the data produced. Integrity testing of the tube bundle lines is required monthly, as specified in Standards Australia AS/NZ 2290.3 (1990). The various forms of integrity testing are reviewed, including pressure testing and introduction of a known gas. This paper provides a recommended and standardised methodology for those techniques where none currently exists. A strengths, weaknesses, opportunities, threats (SWOT) analysis is performed. The parameters considered for the SWOT analysis include resourcing required by the mines, time for the testing to be performed, and quality of the results produced. The suitability of such integrity testing protocols to be used in a mine emergency situation is also evaluated.CITATION:Forrester, L, 2017. Tube bundle integrity testing methodologies, in Proceedings Australian Mine Vent Conference 2017, pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

By David R. Morrey

During the past 50 years, significant research has been performed in the ecology and physiology of plants that colonize soils containing elevated concentrations of heavy metals. Similar work has also been performed on plants that are able to survive acidic and saline environments. Efforts have focused on the ecological analysis of plant communities that occur over a range of metalliferous mining wastes. Investigations have been performed on the mechanisms that allow selected varieties of plant species to survive in normally phytotoxic environments and on the potential applications of metal-tolerant varieties of plant species. The purpose is the remediation and reclamation of mining wastes and soils that contain unusually high concentrations of so-called heavy metals. Characteristics of some mineral wastes Metalliferous mining wastes present special environmental restoration problems because of their toxicity. Potential toxicities are mostly caused by residual metals derived from weathering of low-grade ore or the waste products of mineral processing. In cases where pyrite forms a part of the mining waste, acid generation by oxidation may exacerbate the toxicity problem by promoting heavy-metal mobilization in aqueous solution.

Jan 1, 1995

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002