Search Documents

By H. H. Bein

Most western industrial sands are feldspathic and contain feldspars in variahle amounts. A few deposits will show alumina contents of less than one per cent while others will contain over twelve per cent alumina. Some industries are not especially concerned with the amount of contained feldspar but are interested only in color and in size gradations. Other industries, however, are very much interested in alumina content and set up quite rigid specifications as to this content. Several western plants are beneficiating crude sands both to reduce the iron content and to control the feldspar content. At present, most of these plants are using flotation processes for both controls although a few plants do use magnetic separators for the reduction of iron content. Some work has also been done with electrostatic separators for the feldspar-quartz splits. The Sand Division of Del Monte Properties Company, Pebble Beach, California, has been operating a flotation plant for iron removal and the separation of quartz and feldspar since 1950. As mentioned before, control of alumina, especially in the quartz product, is very important. Some users require an alumina content of less than two per cent and others will demand a product of less than one per cent Al2,O3,. The standard Quinolate method for determining alumina is lengthy and time consuming. The HF —H2SO4 evaporation step is especially critical and, if forced, spattering is apt to occur with a resulting loss of sample. Standard procedure is to evaporate to dry ness overnight at a low temperature. Even with forcing under optimum conditions the procerlnre will take two or three hours to complete. A new method has been developed which allows an alumina determination to be made, in 10 or 15 minutes, on a sample of the quartz product as it is being produced. This pocedure, although simply an approximation, has been most helpful in showing whether or not the product being formed is meeting specifications. This procedure has also allowed a great reduction in samples formerly taken and analysed by the orthodox method. Whether a sample assays 1.75% A12O3, or 1.95% .41,0, is not so important as the fact that it is below the allowable maximum of 2.00%. Similar thinking would apply to products required to contain less than 1.00% A1,0,. The step by step procedures for the method are as follows: 1. Collect sample, drain or filter, and dry. 2. Split sample through standard Jones sample cutter to quarter or eighth sample, depending on size of original sample taken, then split down to about 5 grams through Sepor micro-splitter. 3. Screen through 50 mesh sieve (U.S. Series) and reject undersize. 4. Weigh out 2 grams and place in platinum crucible. 5. Etch with 3-5 mls 38.40% HF for 1 minute at room temp. 6. Decant and wash. 7. Stain for two minutes in same crucible with a 1% water solution of Nigrosene dye. 8. Decant and wash well. 9. Dry.

Jan 1, 1961

By Samer R. Rabab?ah

As part of the PHX Sky TrainTM project at Phoenix Sky Harbor International Airport in Phoenix, Arizona, the existing traffic lanes at the 44th Street underpass below the Union Pacific Railroad (UPRR) Bridge will be shifted to accommodate the people mover guideway. The proposed reconfiguration and reconstruction of 44th Street required the utilization of micropiles and permeation grouting to resist the lateral forces induced by cutting into the slope below the existing bridge abutment footing. This paper discusses the evaluation of the existing bridge abutment, including analysis of the original foundation system, and design, installation and testing of a new micropile-supported retaining wall to support the cut slope below the existing bridge abutment foundation. A monitoring program was implemented during construction to evaluate the short- and long-term performance of the bridge abutment. Instrumentation included survey monitoring points, inclinometers, tiltmeters and crack gauges. A micropile load testing program was conducted to verify design assumptions concerning micropile axial and lateral loading. Numerical analyses (using PLAXIS software) were performed to predict the short- and long-term behavior of both the abutment wall and the bridge foundations. Movement data collected from the monitoring program indicate that the wall and bridge foundations are performing satisfactorily and within the general bounds of predicted movements. The results from the numerical modeling using PLAXIS software showed that the proposed solution is deemed adequate to provide the needed global stability with an acceptable factor of safety, along with acceptable deformation.

Jan 1, 2011

By Verne E. Hooker

This Bureau of Mines report summarizes the results of modifications in the borehole deformation gage design and subsequent changes in the overcoring techniques. Modifications in the borehole deformation gage have greatly improved the creep characteristics and enhanced the versatility of the gage. In situ field tests in competent rock near St. Cloud, Minn., provided sufficient data to compare the reliability between gages and new techniques in obtaining good engineering estimates of stresses. Near-surface horizontal stresses at the test sites are compressive and biaxial in nature.

Jan 1, 1974

By J. H. Brophy, M. H. Kamdar, J. Wulff

A constitutional diagram for the Ta-W-Re alloy system is presented. Rhenium dissolves in the complete range of solid solutions between tungsten and tantalum up to 48 wt pct in tantalum 'to about 30 wt pct in tungsten. Intermediate x and u phases only are found. X-ray diffraction and fluorescence, metallography and melting-point measurements were employed. THE constitution diagram of ternary alloys of tungsten, tantalum, and rhenium for temperatures above 1000°C is reported in this paper. Alloys in this system rich in tantalum and tungsten are of interest for high-temperature applications, and those rich in rhenium for electronic applications. No ternary phase diagram appears to be available in the literature. The three-component binary diagrams have been previously established1-3 and the present ternary data are consistent with these. EXPERIMENTAL TECHNIQUES Commercially pure tantalum (99.7 pct), rhenium (99.99 pet), and tungsten (99.9 or 99.95 pct) powders were purchased from Fansteel Metallurgical Corp., Chase Brass and Copper Co., and Fansteel or Westinghouse Electric Corp., respectively. These powders were pressed without binder and arc-melted under helium. The preparatory and analytical techniques employed were identical to those used for the Ta-Re system investigation carried out in this laboratory.324 These included X-ray diffraction and metallographic phase identification, X-ray fluorescent and wet chemical analyses, solidus determinations and heat treatments in a resistance-heated tantalum-filament vacuum furnace. For microstructural examinations standard mechanical polishing techniques were used through diamond laps. Polished speciments of all compositions were etched by swabbing with 4 parts HI?, 4 parts HNO3, and 1 part H20. Since the microstruc-tures of alloys containing one or two phases closely resembled their counterparts in the respective binary systems, typical examples are omitted in this presentation. In all the alloys examined, it was possible to observe the number of phases present. Particularly when there were small amounts of one phase involved, it was possible to identify it only by a combined conclusion based on X-ray diffraction, position of an alloy in a composition series, and the phase rule. A total of 100 different alloy compositions was arc-melted and studied in the as-cast condition metallographically and by X-ray diffraction. Specimens of each of these compositions were heat-treated at 2680, 2530, and 2020°C for 1, 2, and 4 hr, respectively. Those which were treated at 2020 were given a preliminary homogenization treatment at 2500°C for 1 hr. Specimens of 25 alloys were heat-treated at 1200o C for 168 hr. Solidus temperature measurements were made by the detection of incipient melting in eighteen alloy compositions. The metallographic and X-ray diffraction results are summarized in Table I. Graphically, this information appears in the isothermal plots of Figs. 2 and 3. Within the accuracy of the experimental methods, two such plots are sufficient to locate these data, since the results for 1200°C were similar to 2020 and those at 2530 resembled 2680

Jan 1, 1962

The Menominee Range of northern Michigan was a major producer of direct shipping iron ore for nearly a century. When the last underground mine on the Range ceased operation in 1978, it marked the end of an era. For since the start of mining in the early 1880's the district has gone through a Lull cycle from the start-up of mining through close-down. During this period over 200 million long tons of iron ore were produced and shipped from nearly 100 mining operations. This development and production spanned the time from when the United States advanced from an essentially rural-agriculatural society through the industrial revolution and into the beginnings of the computer and space age. There are many lessons that can be learned from such a rich history. This report attempts to provide ouch a lesson. Through the use of case histories, deficiencies in past mining practices and mine closure procedures that have resulted in current mine related problems are documented. These problems -an be grouped into three areas; 1) subsidence 2) hydrological or drainage problems and 3) problems related to inadequate mine shaft sealing and capping practices.

Jan 1, 1983

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991

By B Clemen, D Gordon, F Cesnik, P Griffin

In March 2002 Newcrest Mining Ltd commissioned a 4 Mtpa gold-copper concentrator at its Cadia Valley Operations in New South Wales. This paper presents the design and construction considerations, commissioning and ramp up issues related to start up of the concentrator as well as current performance and future expansion plans. Commissioning of the plant was the culmination of six years of project planning, from discovery of the resource during the Cadia Hill drill out campaign in November 1996 to project implementation and plant operation. Current resource estimates stand at around 50 Mt with an average grade of 2.4 g/t gold and 0.8 per cent copper. At current processing rates the project life is expected to exceed ten years. The processing plant comprises a 9.75 m (32 ft) diameter Fully Autogenous (AG) mill, a single 6.7 m (22 ft) diameter ball mill, pebble crushers, gravity gold recovery circuit and flotation plant. Upgrades to the existing infrastructure and manning requirements at Cadia will be discussed as well as the resultant impacts on operating costs for the operation. The processing plant was expected to deliver 290 000 ounces of gold and 30 000 tonnes of copper in concentrate in its first full year of operation and progress against that goal will be presented.

Jan 1, 2003

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations. The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works. This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By S. Atallah

A survey was conducted relating to the current practices for the classification of hazardous locations in coal preparation plants. Several plants processing bituminous, anthracite and lignite coal in Pennsylvania, West Virginia, North Dakota, Colorado, Montana and Wyoming were visited. Coal preparation plant operations and designers as well as MESA inspectors were interviewed. The National Electrical Code was discussed with selected members of the NFPA committee and electrical equipment manufacturers. Data provided by MESA on fire and explosion accidents in coal preparation plants were examined. The requirements of the pertinent Federal Regulations, National Electrical Code, National Electrical Manufacturers Association and Underwriters' Laboratories were compared and evaluated. This report consists of two parts. Part I: "Analysis and Review" provides a summary of the findings. Part II: "Recommended Guidelines" consists of recommended uniform guidelines that may be used for interpreting the National Electrical Code as it applies to the classification of hazardous areas in coal preparation plants.

Jan 1, 1977

By Ken Mills

A program of stress change and roadway deformation monitoring was undertaken to measure the forward abutment load distribution about a retreating longwall panel at Dartbrook Mine. The results of this monitoring allow roadway conditions observed at various stages of mining to be ranked according to the estimated vertical stress they have experienced. This ranking also provides a means to predict and visualise future roadway conditions at various stages of mining. This paper presents the results of the monitoring and describes the approach developed to predict future roadway conditions. The monitoring results show the vertical stress distribution associated with the front abutment from a longwall goal decreases exponentially away from the goaf edge. The vertical stress distribution peaks at the goaf edge at 5 to 6 MPa stress increase and decreases to 1 MPa within 50 m becoming imperceptible beyond 100 m By scaling this measured distribution to reflect the loading environment, the vertical stress can be estimated for different overburden depths and different stages of mining. Photographs of roadway conditions at particular vertical stress levels provide a way to visualise roadway conditions at various stages of mining in the future

Jan 1, 2000

By A. G. Pasamehmetoglu, N. Celebi, K. Erarslan

A deposit evaluation system has been developed for a proposed new mine in the basin around Collolar in Turkey. It includes compositing, gridding and reserve estimation facilities and takes account of the economic value of the pit and the pit bottom elevation

Sep 1, 1991

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

By G B. Gnoinski

The Skorpion Zinc Mine and Refinery is situated approximately 25 km north of Rosh Pinah, south-western Namibia. The supergene zinc oxide deposit at Skorpion is hosted in a volcano-sedimentary succession within the para-autochthonous Port Nolloth Zone of the Gariep Belt. Rock types hosting the ore deposit include altered and metamorphosed volcaniclastic and clastic sediments, limestone and rhyolite. At Skorpion, the metallurgical process is unique and the plant design requires minimal fluctuations within a selected feed grade. In addition, the presence of limestone inter-fingered with ore in some areas of the deposit results in dilution problems which may increase gangue acid consumption and therefore processing costs. Hence, selective mining is necessary to ensure the delivery of suitable ore to the processing plant, in order to keep the overall operating costs at a minimum. A complex control system is in place and is capable of a high degree of selectivity. The paper describes the grade control system in place at Skorpion Mine which ensures that the qualities of the blocks planned for mining and the material being mined meet the stringent process requirements of the refinery, i.e zinc grade, gangue acid consumption and deleterious elements that may impact on the efficiency and costs of the metallurgical process. Keywords: Skorpion zinc, zinc oxide, supergene, volcano-sedimentary, grade control

Jan 1, 2007

By Woodcock J. T, Sparrow G. J, MacRae C. M

The external urfaces and interiors (as polished sections) of particles of coconut hell and extruded peat activated carbons taken from everal Australian carbon-in-pulp operations were examined with an optical micro cope, a scanning electron microscope, and an electron microprobe.Calcium carbonate (calcite) precipitated from the pulp was the major inorganic material on the external surfaces of the carbon particle, but several ore minerals, including quartz, hematite, pyrite, arsenopyrite, and clay minerals were also identified, along with trona, gypsum, a nickel cyanide, and a magnesium salt. Sections of carbon particles showed that calcite was virtually the only introduced inorganic material inside the carbons.It was distributed in the pores and cracks throughout the coconut shell carbon particles but tended to be concentrated in the outer layers of the extruded peat carbon particles. The mechanism of calcite formation and deposition is uncertain. Gold X-ray dot maps showed that gold was distributed through to the centre of coconut shell carbons and to a depth of at least 500 µm in extruded peat carbons. The distribution of gold within the carbon particles was similar to that of calcite.

Jan 1, 1988

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By M. C. Mound, E. Gallestey, C. Colbert

Continuous operating performance and high profit is one of the major concerns in the mining industry. Information systems are expected to reinforce and enable conformance to these requirements. The companion efforts of business management and production information systems press for tighter integration to avoid over-laps, multiple instances of similar data, and expensive maintenance of databases. Implementation of advanced intelligent systems throughout a mine operation can reduce costs, optimize investment and create a shorter payback via conversion of the data accumulated by field and process devices into information, and subsequently, into decisions. However, in order to harness the potential power inherent in these intelligent devices, adequate and flexible modular knowledge-based solutions are required. Fortunately, there has been at least one such practical response to this challenge, namely the ABB IndustrialIT portfolio. With these tools in place, production efficiency is reached via integration of process, production, and quality information. Moreover, they permit immediate detection and remedial action to changes to process and boundary condition variables. Finally, using advanced optimization techniques supported by dedicated mathematical models, they allow for economic process optimization (process set points and coordination thereof, energy management, production planning, energy supply contract optimization, etc) of the plant as a whole.

Jan 1, 2004

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals in the hope of understanding the reasons for poor performance when it occurs, and developing mitigating strategies.This testwork along with a review of the relevant literature has demonstrated that the amount of sulphide added to the primary reactor, relative to the copper concentration, is the most critical parameter dictating plant performance, with pH and residence time important secondary factors. The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. Testwork shows that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. The theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are likely to experience growth in crystal particle size through aggregation rather than heterogeneous nucleation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process.There is evidence to suggest that operating the copper sulphide thickener in the SART Process without flocculants may be beneficial. Thickener underflow densities could improve from the current 10 - 15% range to 40 - 50%. This will not only reduce the flowrate of slurry to the filter, but the filtration properties of the slurry (filtration rate, filter cake moisture content) will also improve. This is one of the most critical engineering and design aspects of the SART Process, and the achievement of high solids density in the thickener underflow will not only improve the health and safety aspects of the operation, but also has the potential to lower capital costs and improve the quality of the final product."

Jan 1, 2016

The 108th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Thursday, 11 August, 2005. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Dr Con Fauconnier, President, Chamber of Mines of South Africa Prof. Jay Barton, President, The Geological Society of South Africa V. Townshend, President, Institute of Certificated Mechanical and Electric Engineering, South Africa M. Livingstone-Blevins, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Prof. B. Lacquet, President, South African Institute of Electrical Engineers Dr F. Malan, President, South African National Institute of Rock Engineering

Jan 1, 2005