Search Documents

By M. Bouchard, B. Cadieux et F. Goutier

Five phases of ice movement were r es pons ible f or glacial dispersion in t he study area. I ce fl ow directi on changed prog r es s ively from SE to SSW and then to the S. All observed glacial sed iments are associated with a south-southwest to south movement; t hey are grouped, on the basis of their texture, structure, morphology and composition, into four distinct lithofacies. A lithological study of the coarse-grained fraction (4-128 mm) of these lithofacies shows systematic compositional differences. These are: 1) variations in the proportions of local bed rock fragments; 2) variations in the horizontal displacement of the maximum abundance peak of a given lithology relative to its source area, and 3) variations in the length of dispersion trains associated with each lithofacies. Although dispersal trains can obviously be mapped without differentiating li thofacies, studies based on the consideration of lithofacies should give more reliable results than conventional methods.

Jan 1, 1984

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

By Christopher Jon Preston

This paper describes a type of ammonium nitrate (AN) produced in a patented experimental atomization/aerodynamic process. This AN exhibits outstanding properties for use as a main ingredient to a new family of AN-based commercial explosives. Micro-particle ammonium nitrate (MP-AN) is produced by atomizing either an 83% or 85% AN solution which has been doped with a two component surfactant NSol 1000 (NSol). NSol imparts some water-resistance as well as provides a means of increasing density and bulk strength. Increased detonation velocities, well in the range of emulsion explosives, can be achieved. The maximum manufacturing temperature is less than 100°C. The methodology has the potential of being environmentally friendly since any effluent can be recycled back into a make-up tank to be re-used by the closed loop method. The process has a small footprint.

Jan 1, 2015

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By E. Robles

The Tati Activox® Project (TA®P) is the first step towards the implementation of the Norilsk Nickel Activox® process. The ultrafine grinding (UFG) and autoclave pressure leach process conditions are the heart of the Activox® patent. Low grade base metal sulphide concentrates are leached in the process to recover the base metals and to produce LME grade nickel and copper cathodes and cobalt carbonates. The downstream processing of the metal-containing liquor produced by this process includes solvent extraction circuits to extract and concentrate metal-rich solutions, before the various final products are obtained. This paper gives an overview of many of the relevant design aspects taken into consideration in the design of the Tati Activox® solvent extraction circuits. It addresses key design elements related to leach process conditions such as scaling, materials selection for corrosive solutions, pH control, crud formation and treatment, multiple SX trains designed to prevent organic cross-contamination, and design aspects related to the mitigation of fire risks.

Jan 1, 2009

By Steve Kral

Reducing the cost per ton and increasing productivity are key factors in a mine’s profitability. Mining companies can do little about commodity prices. So to keep a mine operating at a profit, management must reduce costs and improve worker and equipment productivity in every facet of a mining operation. From mining to crushing to processing, mine management is constantly seeking new methods and technologies to improve the way it mines minerals. And it is willing to borrow techniques used by other operators.

Jan 1, 2002

The following notes apply more especially to the purchase of silverlead ores produced in the neighbourhood of Zeehan and Dundas; for it is this class of ore that is principally mined in those parts, and which creates competition among the ore buyers.In the early days of this field, most of the ore passed through the hands of the first buyer who had sufficient enterprise to establish himself at Zeehan but in more recent times, competition has been so keen that there are generally three or four buyers tendering. lf the output was large this would not matter so much from the buyers' point of view but when we consider that the output of the field is only some 1,650 tons per month, and that of this 70 odd tons are produced by the Western and Montana mines, aud being sent home for realization, is withdrawn from local purchasers, there is really not enough for four buyers, especially at the present exorbitant prices they pay the miners.Some of the mines have a fixed sampling day, on which it is tacitly understood that the ore buyers will attend. Others, such as Grubb's Silver Mining Oompany, No-Liability, send round a printed reminder, stating the quantity of ore, and the date of sampling.

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By Cade Mweemba, Alex Mwanza, Jackson Sikamo

"The Zambian Copper mining industry as we know it today has its genesis from early in the 20th century in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production going from zero to a peak of 769 000 tons of copper in 1969. At the same time, the industry created jobs to the extent that in 1972 the industry had over 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level at the dawn of the 21st century in the year 2000 when production was 250 000 tons. In terms of jobs, an average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000. Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and investments of over USD 12 billion, the industry production levels increased year- on-year to reach a peak of 763 000 tons in 2013 with direct jobs reaching 90 000. This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support to other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies and human capital. This is looked at particularly in the light of current challenges the industry is facing and makes suggestions on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2015

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997

By Miklos D. G. Salamon

If all stratifications are horizontal, the computation of surface deformation induced by coal mining involves the prediction of roof and floor convergence and then the transfer of the effects of this relative displacement to the surface through the use of the appropriate influence functions. A laminated model, in the form of a quasi- continuum, provides a simple means of computing the approximate convergence distribution and leads to the Gaussian distribution as the influence function. The ideas presented in this paper represent a subtle but fundamental generalization of the influence function Method. It is postulated that the influence of a small area of extraction is proportional to the roof and floor convergence and not to the thickness extracted. This difference in definition removes many conceptual difficulties associated with the influence function method. To demonstrate the utility of the model, the surface disturbances induced by the extraction of a parallel sided long panel are derived. Formulae giving subsidence, tilt, horizontal displacement and strain are given.

Jan 1, 1989

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

The following paper describes the refining practice for the production of lead, silver and gold at the works of The Broken Hill Associated Smelters Pty. Ltd., Port Pirie, South Australia.The refinery is situated on the wharf frontage and is built parallel with it. The refinery occupies an area of approximately 3380 square yards. (Fig. 8)There are two buildings, one containing the softening and de-silverising sections, measuring 225 ft. x 57t ft., while the other building, which measures 225 ft. x 90 ft. covers the de-zincing, lead moulding, retorting, cupellation, and dore parting sections. (Fig. 1)The retorting, cupellation, and dore parting sections are completely isolated from the rest of the plant by strong small-mesh wire gratings welded to steel uprights. The dore parting plant and generator room are further isolated by a brick wall, built up to the roof. The two main buildings are steel structures, with outer walls and roof of "Robertson" corrugated sheeting; the side and end walls are open for some distance above the ground, and this, coupled with the high roof which is 50 ft. from ground level, ensures the free access of air and light. Conditions are such that operators work in a clear atmosphere.

Jan 1, 1937

DESCRIPTION OF OREThe ore consists, in general, of a very finely grained mixture of sphalerite, galena, and pyrite, with a gangue of quartz and schistose material, and contains about one ounce of silver to the unit of lead.Minor minerals are chalcopyrite, tetrahedrite, and ruby silver. The amount of gangue within the ore-bodies themselves is usually less than 20% of the weight of the whole. The ore is banded in a way that corresponds to the structure of the original schists, and is by no means uniform in composition-at one point, for example, blende may predominate, and a few feet farther on the body may become highly pyritic.Owing to the intimate association of the mineral constituents of the ore, it is very difficult to separate them from one another.Although this remark applies to ore from all parts of the field, the difficulty is particularly noticeable with Rosebery ore, the minerals of which are more intimately mixed, and are of smaller grain size than are the minerals of the Hercules ore.To effect a reasonably clean separation, it is necessary to grind the ore so that 90% passes a 200-mesh I.M.M. screen. Microscopic examination of the crushed product shows that 85% of the minus 200-mesh material is less than 30 microns in diameter, or, in terms of screen sizing, is minus 400 mesh. Particles under 30 microns are found to consist, of one mineral only, but in particles over this size separation has not always been effected. For instance, it is known that part of the galena and of the pyrite in the zinc concentrate is associated with sphalerite, and that part of the galena in the mill residue is associated with pyrite. There is only slight association between the minerals in the lead concentrate.

Jan 1, 1927

Although the pattern of metamorphic zones south of the Thackaringa-Pinnacles Fault is much obscured by polymetamorphism, displacement of the orthopyroxene isograd by the fault agrees with the displacement of a horizon of "banded aplite" mapped by Andrews (1922). A dextral transcurrent component of 20,000 ft is indicated.INTRODUCTIONThe east-west Thackaringa-Pinnacles Fault (Andrews, 1922; King and Thomson, 1953), one of the major geological structures in the Broken Hill district, New South Wales, cuts across the general north-easterly strike of outcrops and fold structures of the Willyama Complex. The degree of shearing and recrystallization in its unusually wide crush zone and the manner in which adjacent rock units and structures have been dragged into conformity with its strike denote considerable movement on the fault. Information concerning the nature of this movement is of critical importance in the search for possible continuations or repetitions of lead-zinc mineralization south-west of Broken Hill.A transcurrent movement of 20,000 ft, with the southern block moving west, was estimated by Andrews (1922), who correlated prominent outcrops of "banded aplite" at The Pinnacles (north of the fault) and Big Hill (south of the fault). Displacement of this order, however, does not seem sufficient to explain the extent and character of the fault zone. Recent chemical and petrological studies of the banded aplites at The Pinnacles and Big Hill by Vernon (19B1) confirmed their similarity, but indicated an origin by metasomatic replacement of pre-existing folded and metamorphosed rocks. This raises the possibility that some...

Jan 1, 1965

By M. du Plessis, D. F. Malan

"The aim of any mine design is to ensure that the excavations remain stable for the period they will be in use. Various pillar systems are used to ensure that underground stopes remain stable and that mining activities do not affect the surface infrastructure through either surface subsidence or seismicity. Intermediate-depth platinum mines make use of in-stope pillars designed to fail while the pillars are being cut at the mining face. The pillar stress exceeds the loading capacity and the pillars crush as a result. The aim of the paper is to provide an overview of in-stope crush pillars. This will include the application, behaviour, function, mechanism, impact, and design of a crush pillar system."

Jan 1, 2015

The first part (lH of this work dealt with the process of recrystallization of single crystals of lead after deformation by creep, as revealed by macroscopical examination. It was shown that when recrystallization commenced, a crystal, termed the primary crystal, started to grow at the edge of the specimen and extended into the body of the specimen along the slip planes. At some stage during the growth of this crystal, other crystals appeared at the boundary of this first crystal and fragments of the parent crystal. From thispoint, recrystallization was accelerated with relatively rapid necking down of the specimen until fracture occurred.All those crystals formed after the primary crystal were given the term secondary crystals. In the present paper is given a detailed account of the orientations of the primary and secondary crystals.EXPERIMENTAL METHODThe size of the test pieces and the manner of loading were given in the previous paper (1). X-ray back reflection photographs were taken of the individual primary and secondary crystals and from them were determined the orientations. The path of the X-ray beam was perpendicular to the surface of the creep specimen.In view of the large number of photographs needed, gold...

Jan 1, 1940

By C. Lemmer

The resolution with which the different categories of resources are forecast for Witwatersrand gold reefs should ideally tie in with block sizes that are optimal in terms of the variability structures of the reefs. A tool, called the ?variancegram?, is proposed as a basis for block size choice. A variancegram is intrinsic to the particular reef and mine concerned. A further requirement is the ability to attach global confidence limits to weighted average estimates built up from combinations of local kriged estimates. Approximations to derive global kriging variances based on variables derived from local kriging deliver hugely inflated results if ordinary kriging is used, and markedly better, but not accurate, values if simple kriging is used. These approximations improve as the number of samples used in kriging each block is increased. It is shown that the behaviour of the different components of the global kriging variance with increasing number of samples, all differs, but they all link to the variancegram for the particular reef. The variancegram can thus be used to correct the different components to the values they would have had if all samples were used in kriging each block, and so deliver the ?correct? global kriging variance, even though only a limited number of samples were used in kriging each block. The desirability of having very stable solutions implemented in production systems is taken into account in the proposals. It is anticipated that the same variancegram findings will also hold for other densely sampled deposits, but this remains to be investigated.

Jan 1, 2014

By Z. W. Nkosi, M. Sephton, J. H. Potgieter

The exhaust system is a complex assembly of various components performing important tasks in harsh environments. Carbon steels have been used extensively in exhaust systems, but pressure for lower cost, increased fuel efficiency; lower hazardous emissions, weight savings and increased life expectancy have shifted the emphasis to stainless steels. In response to the growing consumption of stainless steels in automotive exhaust systems, the need to properly evaluate their corrosion resistance properties in order to ensure their appropriate use, has increased substantially. This paper evaluated the most common corrosion and oxidation tests developed that are used and applied it to four common stainless steels often employed in hot end exhaust components. In a summary considering the weight loss of an alloy, it general corrosion rate and pitting resistance under all the test conditions for hot end exhaust components, results indicate that 434 was by far the most corrosion resistant alloy, followed by 1.4509 and 321, and lastly 304 was the least corrosion resistant. In general, the ferritic stainless steels, especially 434, outperformed the austenitic ones under all the test conditions.

Jan 1, 2006

By Dale Bartholomae, David Harrison, Edward J. Walter

Methods that involve the use of signature blast holes in order to identify the particular frequency characteristics of a geographical area are widely available. Information acquired can be used to determine optimum blast hole timings to produce the desired constructive and destructive inference. However, these types of analyses can be both complicated and expensive. This study will investigate the use and practicality of signature hole and/or shift and sum analysis software and their application to small diameter construction utility blasting operations in Pennsylvania and faster moving projects in general. A determination will then be made as to whether this technology can be utilized by today’s blaster, from both a functional and a cost effective basis. Single hole blasts will be detonated on various smaller construction projects and will be monitored with an array of seismographs. The collected data will be analyzed in order to determine the optimum timing between holes to produce the preferred frequency content while keeping in mind the explosives user’s current inventory of blasting supplies.

Jan 1, 2005