Search Documents

By Orr C. W

In previous papers (1, 2), the influence on the creep resistance of elements normally found in commercial lead has been recorded. The results in the present paper refer to the influence of calcium, an element which is not found naturally in lead, but which has been used commercially in the form of alloys. It was realised that calcium would act as a deoxidising agent for lead-and in fact it was with this feature in view that both calcium and magnesium were used as additions. Subsequent work (including the results given in the present paper) has tended to diminish the importance which at first seemed to be associated with the presence of oxygen in lead. The structure of the dilute calcium lead alloys has been worked out in detail (S) and the phase diagram shows the existence of limited solid solubility and a compound CaPbs.

Jan 1, 1938

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia.An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared.The difficulties of distinguishing structured and nonstructured macerals of the inertinite group are discussed in terms of possible improvements to the present StopesHeerlen system by extending the classification to include transitional maceral types.

Jan 1, 1970

By Edwards A. B

The occurrence of lollingite (FeAs2 ) in the Broken Hill lode is recorded by an analysis of lollingite published in the Annual Report of the Department of Mines, New South Wales, for the year 1934 (p. 69). The analysed specimen came from the North Broken Hill mine, and material from the same occurrence (Specimeh No. 1), as well as two specimens (Nos. 3 and 4) from the Zinc Corporation mine, have been forwarded· to us by Mr. M. Mawby of the Zinc Corporation Mine. This material has been supplemented by another specimen (No. 2) from the Zinc Corporation mine, passed over to us by Dr. I. Wark.The original analysis of lollingite is quoted in Table I, and shows that the Broken Hill lollingite contains appreciable amounts of cobalt and nickel, and, indicates that the iron is to a considerable extent replaced by cobalt and nickel, so that its formula should be written (FeCoNi) As2This is supported by a microscopical examination of a polished surface of the lollingite, in which no individual arsenides of cobalt and nickel can be detected.Coarse grained galena, sphalerite, chalcopyrite, and pyrite are attached to our specimen of lollingite from the North mine, and are separated by a sharp junction from a mass of lollingite associated with some arsenopyrite and garnet. The massive lollingite can be distinguished from arsenopyrite in the hand specimen by a much brighter, silvery lustre, against which arsenopyrite appears a dull silver grey; but the passage from lollingite to arsenopyrite appears transitional.

Jan 1, 1939

By Gavin J. Faulkner

This paper presents an investigation of some alternatives, and improvements to timber posts and cribs. The purpose is to find a cheaper, better, easy to install, and effective means to replace or improve them. Selection of supports needs to take account of several factors. These factors include the mechanical behavior of the support, technical feasibility, and cost. In this paper a variety of supports are compared on these bases. Particular advantages and disadvantages of those supports have been determined through published material and a testing program. A broad evaluation of a number of specific groups of supports is presented. Included in this evaluation are timber posts and cribs, steel friction props and several, newer developments such as the Micon Yield Capsule and the Super Post. Another support that will be briefly discussed is steel-fiber-reinforced concrete. Particular emphasis will be placed on the Micon Yield Capsule and the Super Posts on which preliminary testing has been carried out. The testing results are presented in detail. The shortcomings of the test procedure are pointed out and some new ideas to improve the testing in the future are proposed.

Jan 1, 1986

By F E. Grader

A linear motor properly wound can serve as a mechanism for separating paramagnetic sulphide minerals, like pyrrhotite, from other sulphides and associated gangue minerals. The effectiveness of separation depends on the energising current of the separator, the frequency of the ac cycle, and the particle size of the minerals. The speed of travel of the minerals over the surface of the separator is also a function of particle size, and appears to be constant. The movement of pyrrhotite, magnetite and iron filings of comparable size fraction (150 ¦m +74 ¦m) on the linear motor surface has been observed using a cine camera. An attempt, has been made to give a theoretical basis for the movement of the particles by calculating the minimum electrical energy required to move them. Further, the rate of decay of magnetic moment of the particles has been estimated for magnetite and it has been found that sufficient residual magnetism existed in the particles after they had been exposed to the first half of an ac cycle for them to have like polarity with the second half of the cycle. The particles are therefore repelled from the motor surface every second half of the cycle. This repulsion due to remanent magnetism is the probable cause of particle movement over the linear motor surface.

Jan 1, 1980

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By Ralph B. J, Sadler W. R

Thiobacillus ferrooxidans was shown to catalyse biodegradation of chalcopyrite concentrates. The process was growth associated at normal temperatures (30°C) in dilute acid solution (pH2, H2SO4) in submerged cultures. Approximately 20% of the copper dissolved in 22 days in the presence of T ferrooxidans while less than 0.6% was released when bacteria were absent. In ore column leachates, the iron and sulphur oxidizing species T ferrooxidans, ranged from I04 to I06 cells/ml while exdusively sulphur oxidizing species ranged from I02 to 104 cells/ml. T ferrooxidans predominated below pH 3 while other sulphur oxidizing bacteria favoured higher pH. Organisms were distributed vertically in ore columns according to pH differences, resulting from gradual acid consumption by gangue, during trickle irrigation.There was a sequential development of bacteria in leachates from fresh ore irrigated with water only. High pH sulphur oxidizers were always present, low pH sulphur oxidizers appeared within a week while T ferrooxidans took 50 days to show up. Routine monitoring of bacteria in dump leachates provided a qualitative indication of events in otherwise inaccessible ore bodies.

Jan 1, 1981

By D. Goossens

Quality control is a system which should guarantee that quality is achieved. It is the execution and verification of a project in an organised way, in order to obtain the maximum of certainty that the results meet the requirements. This concerns all stages of the project, from the soil investigation, over the design, to the execution. Quality control can and has been successfully realised for important projects by means of a quality plan. A quality plan is based on a number of general considerations, but should certainly be focussed on the particularities of a specific project. Practical examples of quality plans, which have been realised on sites in Belgium, are developed and the advantage of the system is shown by concrete case studies.

Jan 1, 1996

By John R. FitzPatrick

The separation and purification of uranium from either nitric acid or hydrochloric acid media tan be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated' to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps. We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (100-gram) flow experiments using depleted uranium, were done after the small-scale evaluation Of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments' involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and' amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process. Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail.

Jan 1, 1996

By N. Coli

The exhausted Santa Barbara open pit mine (Tuscany, Italy), owned by the main electric power company in Italy (ENEL S.p.A,) extracted lignite as a fuel for the Santa Barbara thermoelectric power plant. The mining activity led to the excavation of a wide slope (with maximum height of 200 m and a planar extension of about 1300 m x 500 m) in the Shale Limestone Chaotic Complex (SLCC) (Figure 1). Since the beginning of its excavation the slope underwent rotational landslides and diffuse instability phenomena. From a geotechnical point of view the SLCC represents a typical bimrock (block-in-matrix rock) (Medley 1994, Medley 2002, Medley 2007) characterized by a mixture of a highly sheared, scaly-fabric, clayey matrix and calcareous blocks ranging from a few millimetres to tens of metres in size. Since the geometrical properties of blocks (grain-size distribution, shape, orientation and volumetric proportion) have been proved to influence the mechanical behaviour of bimrocks (Lindquist & Goodman 1994, Goodman & Ahlgren 2000, Kim et al. 2004, Sonmez et al. 2006), the aim of the present study is to investigate the geometrical properties of calcareous blocks in order to properly characterize the mechanical behaviour of the SLCC bimrock and to further assess the stability of the slope. Block size-distribution and shape were investigated by means of advanced image analysis techniques of SLCC pictures taken in the field. Geostatistical semivariograms and variographic maps were also used in order to investigate the anisotropy of block spatial distribution. Finally, in-situ large sized sieving tests were carried out to investigate the volumetric block proportion within the clayey matrix.

May 1, 2009

By Paul Staples, Paul Messenger, Greg Lane

"Every project is different. While “conventional” SAG and ball mill circuits will suit many projects, for others there are alternatives, which may produce improved outcomes. This paper examines particular examples of recent front end designs which either went against conventional thinking or which employed “out of the box” thinking to realize the desired results.One such example is the design strategy employed for a small capacity gold plant in Victoria, Australia. The selection of HPGR technology for small capacity projects is not generally favoured, given the relatively high cost of small HPGR machines. However, the unusual size distribution of the gold and its liberation characteristics were expected to lead to improved gold recovery offsetting the higher capital cost.Another example is the first large scale application of milling in acid for copper recovery, at a project in south east Asia. The stainless steel, single stage SAG mill using ceramic grinding media was more expensive than a mill constructed of conventional materials. However, the steps of scrubbing, slurrying, grinding and leaching could all be achieved in a single unit operation and the need for thickening and repulping with acid after milling was eliminated.Rod mills were selected for both primary and secondary milling duties for another south east Asian project despite their somewhat outdated reputation. A review of previous industry experience confirmed that rod mills could outperform conventional rod/ball or SAG/ball circuits in cases where the size distribution of the ground product is critical to downstream recovery.These examples are discussed with particular focus on the key drivers in each case."

Jan 1, 2008

By X. S. Tan

This paper deals with the analysis of stress condition on the interface between two types of floor rock materials when the vertical stress is larger, or when the horizontal stress is larger in a rectangular opening. It indicates that the floor Failure and the failure stress of floor rocks are closely related. It also demonstrates that a larger horizontal stress is one of the most important factors in increasing the potential for floor rock failure and floor heave.

Jan 1, 1990

WHEN making comparisons of the efficiencies of different grinding and crushing machines it is desirable to be able to estimate the work actually done in crushing the ore from a given size of feed to a given size of product, the screen analysis of both feed and product being determined. Messrs. Klug and Taylor, in a paper on this subject, published in the monthly journal of the Chamber of Mines of WA, 31st January, 1906, have described a method adopted by them in calculations made in connection with a series of trials of grinding pans. Their methOd is based upon the assumption that if a quantity Q of material consisting of particles of average diameter x be crushed down until the average diameter of the particles is y, then the work done in grinding is proportional to Q x. There is no theoretical basis for this assumption that the writer is aware of, and it does not appear to satisfy the fundamental conditions necessary. If the material be further crushed until the diameter 2 becomes Z, the additional work done is measured. The work done in crushing from diameter x to diameter Z in one operation is proportional to Q x:, and therefore we ought to have zx2 y2 x2 Q-+Q-=Q-. y2 Z2 Z2But these expressions are not in general equal to one another. In other words, according to the theory underlying this method, if we crush from diameter x to diameter y, and then from diameter...

Jan 1, 1909

By Vincent A. Scovazzo

On March 12, 1994, the 1,100-foot deep 2 Yard South panel of the 1l0 year-old Retsof Mine collapsed. At the time of this occurrence, the Retsof Mine was characterized as the world's largest, most productive salt mine. The collapse produced a seismic event and resulted in a sinkhole and small lake forming on the surface. An existing highway bridge was rendered unusable. Water entered the mine and despite valiant efforts by the miners and the mining company, the entire mine was flooded and lost. John T. Boyd Company (BOYD) studied the incident to evaluate design procedures, and assess the short- and long-term environmental impacts of the collapse. This paper presents our analysis of the cause of the collapse and our review of the rock mechanics design of 2 Yard South panel. Our review is, in part, based on a rock mechanics monitoring program of 2 Yard South. The monitoring program was established by the mining company as the panel was developed and continued even after the panel became unstable.

Jan 1, 1997

By S. R. Zimmerley

As a result of the drilling program of the :Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By S. R. Zimmerley

As a result of the drilling program of the Mining Division, Bureau of Mines, large amounts of manganese ores have been blocked out in the Drum Mountain District of Utah. The ores, as mined, would not be acceptable for the production of ferromanganese, and this investigation was made to determine their amenability to concentration by ore-dressing methods and the amount of

Jan 1, 1942

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By William M. Gleason

When SME’s 2006 Arizona Conference convened in December at the Hilton El Conquistador Resort in Tucson, AZ, there was considerable excitement among the 387 attendees. There was a noticeable buzz surrounding the progress of Phelps Dodge’s Safford copper mine in southern Arizona, one of the first new major copper mines to be permitted in more than 30 years in the United States. There were also plenty of good feelings about the mining industry in general. Commodity prices remained high and with no signs of a slowdown in the immediate future. Things were good in Arizona. But there were also cautionary tones at the conference and the Mining Foundation of the Southwest banquet that preceded it.

Jan 1, 2007