Search Documents

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

By Bowang Xiao

Recently more and more attentions are paid to high pressure hydrogen quenching (HPHQ) for its advantages such as environmental friendliness, low distortion, etc, compared to oil and water quenching. In HPHQ process, heat transfer coefficient (HTC) usually varies from part surface to surface because of the intense variation of gas velocity around the part. This article studies the effect of HTC distribution on part distortion after HPHQ and shows that finite element simulations considering HTC distribution predict different distortion from these without considering HTC distribution. It is also pointed out in this article that HTC distribution can be optimized by adjusting part orientation and HPHQ condition so that part distortion is minimized.

Jan 1, 2010

By H Fukui, K Ichikawa, K Aikou, E Suzuki

An electronic delay detonator (EDD) consisting of a digital-base electronic delay module and a conventional instantaneous detonator module, designed for series connections with a special adjustable-output blasting machine, is described and shown to provide a delay time accuracy some four to twelve times higher than that of pyrotechnic millisecond and decisecond delay detonators, together with the other performance characteristics necessary for practical use. Also described is a blasting design system which allows effective reduction of ground and air vibration, through the use of EDDs with optimum delay times as determined by accurate computer simulation based on wave form and other data obtained from an on-site single-shot test blast.

Jan 1, 1989

By Shen Zhengchang

Based on the flotation features of coarse particle mineral, a new type of impeller & stator unit is developed. Particles suspension state generated by this impeller & stator unit under different speeds are tested in laboratory, and critical impeller speed suit for coarse particles flotation is presented. Comparing particle suspension parameters of the new impeller & stator unit with that of KYF impeller and stator unit, it comes up that the distance between the interface of two slurry circulation channels and the cell bottom is larger in the flotation cell with new impeller & stator unit. The test results indicate that the new type of impeller & stator unit is suitable for processing coarse particles due to its good suspension capacity for coarse particles. Keywords: coarse particles, flotation, suspension, critical speed, impeller and stator unit

Sep 1, 2012

A Study on Main and Interaction Effects of Operating Variables of Column Flotation

Sep 13, 2010

By F. Q. Dong

According to the principle that should be originated from nature, compatible with nature, used in nature and back to nature and based on conception of designing of eco-material, the author combined the ideas of material, environment, zoology and healthy. Properties of natural mineral materials were used to produce micro-aggregate elements by bionic method, so its components and function could accord with living environment. Eco-mineral functional materials which can adjust, purify and optimize the microclimate were reviewed. The authors pointed out the multifunction, com-pounding, the compound characteristics and integration regularities of micro-aggregates. It was the first time in the world to put forward the ?gene? technique or ?material chip? technique of manufacturing function micro-aggregates and eco-function elementary materials. The results of this re-search supported by the national ?863? Hi-tech Project, mainly including the high-efficient air purifying mineral compound material indoor, the clay elementary antibacterial materials, the masonry cement/coating/putty/compound with preventing radon radiation, environmental friendly composite functional coatings, mosquito repellent and healthcare material and zeolite-based energy-saving composite materials, were introduced. Finally, the foreground of mineral materials in the field of future advanced eco-friendly materials was also discussed.

Jan 1, 2014

By Cem Colakoglu

In this study, nickel containing iron alloys were produced by carbothermal reduction of lateritic nickel ores obtained from Manisa - Caldag region of Turkiye in order to investigate the reaction mechanism of nickel and cobalt. In the experiments, the lateritic ore containing 1.58 wt.% Ni and 0.12 wt.% Co was calcined in a semi-pilot scale rotary furnace at 1100°C for 1 hour. Then, a mixture of calcined ore and metallurgical coke was reacted in sintered alumina crucibles using a graphite resistance tube furnace at different time (0- 60 min) and temperature (1500-1600°C).

Jan 1, 2009

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By L. Shuyi

In order to develop the pulsating high gradient magnetic separation technology, a type of laboratory pulsating high gradient magnetic separator (PHGMS) has been manufactured. Experiments of its separating performance were carried out. They show that PHGMS can significantly increase the grade of the magnetic product and avoid the matrix to be blocked. The characteristic curve of the pulsating fluid was measured and a formula for estimating the grade of the magnetic product was established in PHGMS.

Jan 1, 1990

By Ranajit Kumar Sahoo, Shatrughan Soren, Surendra Kumar Biswal, Soumya Sahoo, Sachida Nanda Sahu

The presence of appreciable quantity of clay mineral in Indian hematite ore needs an attrition technique using screw scrubber in the beneficiation circuit to remove the ultrafine clays and avoid downstream operational problems. Spectroscopic analysis revealed that iron ore samples obtained from the Barbil region of Odisha contain a high amount of silica and alumina in the form of clay minerals (e.g., kaolinite) contributed as a loss on ignition (LOI) in the iron-making process. Iron ore fines of below 10 mm size were subjected to a laboratory-scale screw scrubber, and the effectiveness of scrubbing as well as the pelletization of the scrubbed product was investigated. The screw scrubber in the beneficiation circuit helps to remove the clay minerals, causes an increase in iron values from 63.65% Fe(T) to 66.18%Fe(T), with improved physical (CCS of 325 kg/pellet) and metallurgical (RDI of 2.24%) pellet properties.

Aug 31, 2020

By S. Jeon, T. H. Kim

"Understanding the frictional properties of discontinuities is crucial to ensure the stability of underground structures. In particular, the frictional behavior at depth depends on the complex interaction among mechanical, hydrological, thermal and chemical characteristics and their coupled effects. In this study, a series of triaxial compression tests were carried out to investigate the behavior of rough shear surface of synthetic rocks. The frictional behavior showed little variation at different confining and water pressures. The test results were analyzed using Coulomb’s failure criterion. In addition, numerical analysis was carried out using PFC2D to simulate the test.INTRODUCTIONUnderstanding coupled behavior of rock at depth is of great importance in design, construction and operation of underground structures such as a disposal facility of radioactive waste, hot dry rock geothermal system and oil reservoir. In particular, many uncertainties are involved in characterizing deep rock mass deformation in the designing process and interactions among fluid flow of groundwater, high temperature and stress disturbance should be considered. Many independent studies have been carried out to investigate the thermal, hydro, mechanical and chemical coupled effects in numerical and experimental methods. They include the researches by Lockner, Summers, Moore and Byerlee (1982), Jafari, Amini Hosseini, Pellet, Boulon and Buzzi (2003), Tembe, Lockner and Wong (2010), Lee, Lee and Jeon (2012), Indraratna, Premadasa, Brown, Gens and Heitor (2014)."

Jan 1, 2015

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By Park Yun-Seok, Jung Seung-Won, Hwang Nam-Sun, Song Jin-hyuk, Kim Young-ho

This study proposes a new blasting vibration estimation formula that reflects the vibration reduction characteristics of electronic detonators, which are not considered in the current MOLIT blasting vibration estimation formula. Test blasts were conducted across six types of Korean open-pit blasting designs. The results of the test blasts showed that the K value for electronic detonators decreased by approximately 30% compared to electric detonators. Predicted Peak Particle Velocity (PPV) analysis indicated a reduction effect ranging from 30% to 31% across various types. By incorporating this reduction in the K value into the MOLIT blasting vibration estimation formula (K=200), a new electronic detonator blasting vibration estimation formula (K=140) was proposed. Using this new formula, the blasting damage range (R) was calculated under various vibration limits to evaluate constructability improvement. On average, the R value for electronic detonators decreased by about 17%, with significant reductions of around 41% observed for TYPE I under certain vibration limits. In conclusion, the adoption of electronic detonators in open-pit blasting operations improves blasting efficiency, reduces economic costs, and significantly enhances constructability. Electronic detonators have demonstrated superior performance in minimizing damage to safety facilities compared to traditional electric detonators, thereby proving their practicality and effectiveness in blasting operations.

Jan 21, 2025

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

There are mainly three commercial nickel laterites in Turkey: Gordes, Caldag and Sivrihisar. The first two appear in Western Anatolia. The third one, Sivrihisar (Yunusemre) laterites have been found in the first decade of the millennium, in the Central Anatolia region of Turkey. Since then, mining facilities have been continued in Yunusemre. Calcination, prereduction and smelting of Sivrihisar laterites have been extensively studied and published. In the current work, some results of the studies related to characterization of Sivrihisar laterites will be presented.

Jan 1, 2016

By Yeon-Ho Jin, Eui-Haeng Heo, Yun-Seok Park, Sung-Oong Choi, Hyung-Dong Min, Min-Su Jeong, Seung-Joong Lee

As rock fragmentation in bench blasting can affect the following process such as loading, hauling and crushing, its good control is essential for assessment of blasting efficiency and production cost.

Jan 1, 2015

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011

By A. Dabbagh

The aim of this research was to investigate the effect of coke particle size on the thermal profile of the charge bed in the sintering process of iron ore. Six different ranges of coke particle size that could be used in practice in the sintering line of Esfahan Steel Company (ESCO) were used while parameters such as ratios and particle sizes of other ingredients, ignition temperature, and suction power were kept constant. Thermal profiles were obtained by measuring the temperature changes at three points in the sintering bed. The influence of coke particle size on rate of temperature rise, maximum temperature of the sintering bed, and the flame front velocity of the sintering bed was determined by analysing the thermal profiles. Moreover, the cold strengths of the sinters were measured using the Tumbler method. The results indicated that the coke particle size has a significant impact on the thermal properties of the sintering bed. Based on the results, a coke particle size between 0.212 mm and 3.350 mm was determined as the optimal range for the specific conditions in the sintering line of ESCO. Keywords iron ore sintering, coke particle size, thermal profile, flame front velocity, Tumbler index.

Dec 1, 2013

By S. H. Shahcheraghi

The four operational parameters including collector dosage, frother dosage, conditioning time and pH, are the most important parameters effective on the flotation kinetic. The present study has been done at the Miduk Copper Complex in the province of Kerman. The effect of operational parameters on the flotation kinetic of copper minerals were studied and analyzed, so the optimum conditions for flotation kinetic of copper sulfide minerals were obtained. Under the obtained optimum operational conditions, the recovery of copper sulfide flotation at the 95% confidence level was estimated to be between 92.76% and 95.48% and the copper sulfide flotation kinetic constant was estimated to be between 1.40 and 1.45 min-1. Results showed that the consumption of the X231 collector (O-isopropyl-N-ethylthionocarbamate) and the A65 frother (Polypropylene glycol) could decrease up to 35% and 50% respectively while the copper sulfide recovery increases about 1 up to 2% at the laboratory scale. Keywords: flotation kinetics, sulfide copper, optimization, the Miduk Copper Complex, response surface method

Sep 1, 2012