Search Documents

By Helmut Antrekowitsch

Nowadays nearly the half of the world zinc production is used for galvanizing. After their life span most of the galvanized products return as scrap to the steel mill During the steel process the zinc is collected in the flue dust It is astonishing to notice that between 40 and 50 % of the zinc produced is brought into the steel processing cycle by the coated scrap while only 3 to 5 % of the zinc production can be covered by the recycling of the zinc-bearing steel mill dusts. Responsible for this worse ratio is the fact that the established recycling technologies suffer from high energy consumption, low zinc yields, halogen problems and hardly any iron recovery. A development of new or an optimization of current recycling procedures for the dusts is unalterable because of increasing zinc amounts in these residues and the rising costs for the disposal. Different pyrometallurgical recycling technologies are tested in rotary kilns and vertical retorts at the Department of Nonferrous Metallurgy, University of Leoben, Austria. Various reducing agents from carbon monoxide to hydrogen and combinations are used. The results should make it possible to draw conclusions that allow an economical and ecological judgement of the different varieties. The goal is to support the affected industry to increase the low recycling rate and prevent a loss of high zinc values in the steel industry filter dusts.

Jan 1, 2003

By V. D. Tathavadkar

Natural chromite mineral is a solid solution of spinet end members namely: chromite (FeCr2O4), hercynite (FeA1204), magnetite (Fe3O4), magnesio-chromite (MgCr2O4), (MgA12O4), and magnesio-ferrite (MgFe2O4). A phase transformation in chromite minerals occurs in oxidising conditions during the soda-ash roasting reaction. This phase transformation plays an important role in improving the extraction efficiency of Cr3+ from mineral phase. The extraction efficiency of chromium (Cr3+) from chromite to a water¬soluble sodium chromate (Cr6+) salt depends upon the decomposition kinetics of the spinet phase. An investigation of the phase changes in chromite ores in the absence of sodium carbonate was carried out in air, argon, and in argon +5 % hydrogen gas mixture. The thermodynamics of phase transformation reaction in chromite solid solution phase is discussed using the solution model proposed by Sack and Ghiorso [1]. The microstructural changes and the changes in elemental compositions of different phases were examined by SEM and electron probe microanalysis (EPMA) respectively. The experimental results indicate that the solid solution spinet phase in chromite mineral undergoes spinodal decomposition under the influence of oxygen partial pressure and temperatures. The structure of phases formed and their morphologies suggest that the phase decomposition may be similar to those observed by Burkert et. a]. 121, although the scale of phase separation in chromite appears to be strongly dependent on oxygen partial pressure.

Jan 1, 2001

By Paul Van Negan

During the last decade, MHO has continued to diversify the feed. of its Hoboken smelter. The range of feed materials including larger proportions of precious metals has been extended and the production of minor metals has been developed. These diversifications have required further improvements at the smelter. Attention has been particularly focussed on an increase of productivity, compliance with emission standards and achievement of the highest recoveries of valuable elements. The assaying and sampling facilities have been considerably expanded and the different processing steps of the smelter are now also systematically controlled and managed by simulation models. The charge preparation at the sinter plant, returns handling, sinter conditioning and corresponding ventilation systems have been completely renewed. The annual smelting requirement is now achieved with two blast furnaces instead of three. This is the result of rebuilding and enlarging one of the furnaces and, of a completely new concept of the charge proportioning and charging systems, together with oxygen enrichment and blast air preheat. Ventilation capacity has also been drastically increased. A 7 MVA electric furnace for cleaning the slag from both blast furnaces. contributes to improving the overall metal recovery.

Jan 1, 1990

By J. L. Johnson

Remediation of small-arms firing ranges is being investigated by the Naval Civil Engineering Laboratory and the U.S. Bureau of Mines. Scheduled closures of military installations, as well as the management of active ranges, require the development of methodologies for heavy metals removal to prevent their entering the surrounding environment. The impact berms contain high concentrations of metals, and the soil and vegetation surrounding the berms were found to have slightly elevated levels. The heavy metals characterized are in the form of whole bullets, a wide size distribution of free fragments, smeared lead on the surface of the soil grains, and very finely attached particles. Gravity beneficiation can remove liberated metal contamination effectively. Weak acetic acid leaching shows promise in lowering the final metal contamination to allow the soil to pass the Environmental Protection Agency's (EPA) Toxicity Characteristic Leaching Procedure (TCLP) criteria.

Jan 1, 1991

By Ivan Imris

The common problem of new and conventional technology of copper production is the copper losses in the slags, which may be divided into mechanical and physico-chemical losses. In the first group can be included particles of mechanically entrained or floated unsedimented matte particles which coexist with slag. On the other hand, the physico-chemical losses are caused by solubility of copper in the slag in the form of sulphide and oxide. The copper losses in the slags from different processes has been predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and quantitative electron microprobe analysis. Depending on the forms of copper losses in the slag the reduction of copper losses in the slag or the slag cleaning process could be suggested.

Jan 1, 2003

By Cajsa Samuelsson, Theo Lehner

Converting and refining play a central role in the extraction of metals. Sweden has a long tradition as an experimental play ground for metallurgists, chemists and alchemists, developing new methods and technologies. Presenters of papers are usually happy in recording successful developments. But reporting failures can be as great a value as the former. In the paper experiments and experience in process development are illustrated, differences between ferrous and non-ferrous developments are highlighted and industrial learning curves are discussed. 53

Jan 1, 2009

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu20), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, CU2O- bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties ofthe CaO-FeOx-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation.

Jan 1, 2003

By Mingming Zhang, Marshall S. Coe, Marcelo W. Andrade

To supply iron units and flux burden in blast furnaces, sinter basicity is one of the vital parameters for sinter plants. The sinter basicity also plays an important role in sinter quality since it imparts the formation of different mineral phases in sinter. Pot-grate sintering tests were carried out with low and high basicity to investigate the effects of sinter basicity on sinter mineralogy, properties and productivity. It was found that with an increase in sinter basicity, both sinter productivity and reducibility (RI) increased. Tumbler index (TI) and low temperature degradation index (LTD) of high basicity sinter were comparable to low basicity sinter. Softening and melting tests showed that sinter with 3.5 C/S basicity had slightly higher softening temperature comparing to lower basicity sinter with C/S 2.6, acid and fluxed pellets. XRD analyses confirmed the formation of silico-ferrite of calcium and alumina (SFCA) and calcium ferrite (CF) in the tested sinter samples.

Jan 1, 2015

By David G. Dixon, Maziar Eghbalnia

"Gold and silver nanoparticles (NPs) were deposited on pyrite at ambient temperature from colloidal solutions prepared by reduction of hydrogen tetrachloroaurate or silver nitrate by sodium sulfide or sodium tetrahydridoborate. The nanoparticles were characterized using Ultraviolet-Visible (UV-Vis) spectroscopy and the experimental spectra were fitted using Mie - Gans modeling. The modified pyrite was investigated using Electrochemical Impedance Spectroscopy (EIS). Electrodes were prepared from both natural and modified pyrite samples and were modeled using an equivalent circuit (EC) based on the EIS data. The comparison of the results revealed a decrease in charge transfer resistance for the ferric ferrous redox couple associated with the modified pyrite. From this behavior it is concluded that the electronic transport between the nanoparticles and the electrode surface over distances in nanometer scale is enhanced. Nanoparticles below a certain size act as quantum dots due to electronic confmement. Decreased charged transfer resistance at the nanometer scale may be caused by electron transport through tunneling mechanism via quantum dots.IntroductionIn recent years, considerable attention has been focused on the synthesis and study of Metal nanoparticles due to their potential applications in the fields of physics, chemistry, biology, medicine, material science and their interdisciplinary fields[!]. When material is nano-sized, the physical properties deviate markedly from those of bulk material, however, this effect is highly dependent on the particle size, interparticle distance, and morphology of the nanoparticles [2].An extremely small region of space defmed in a semiconductor material in order of nanometers is called a quantum dot, a term coined by Reed [3]. The three dimensional confinement of quantum dots can change properties of the excitons in comparison to free excitons in a bulk material [4]. Nanoparticles behave electronically as zero-dimensional (restricted in all three dimensions) quantum dots when the de Broglie wavelength of the valence electrons and the particle are in the same size range.As Reed [3] explains electrons confined in a plane have no freedom to move the third dimension. Those confined in a quantum wire are only free to move in one dimension, and those confined in a quantum dot are not free in to move in any dimension. An electron inside a cube of material IO nm on a side is confined to a point."

Jan 1, 2012

By P. N. Anyalebechi

"The as-cast microstructure of two commercial-size ingots of aluminum alloy 3004 produced by the electromagnetic casting process was quantitatively characterized. This involved the quantitative determination of through-thickness and across-width variations in dendrite cell size, grain size, macrosegregation of alloying elements, interparticle spacing, and the types, volume fractions, and sizes of the constituent or second phase particles. More than ninety-five percent of the constituent phases in the ingots consisted of the A16(Mn,Fe) phase; the desirable a-Al 12(Fe,Mn)3Si phase was not detected in any of the ingots by Guinier X-ray diffraction analyses or electron probe X-ray microanalyses. A significant microstructural heterogeneity through the thickness and across the width of both ingots was observed. For example, macrosegregation, and the sizes of the constituent phase particles, dendrite cells, and grains increased concomitantly from edge to mid-width and from surface to center of the ingots. There was a -20% depletion (negative macrosegregation) of Mg and a +54-87% enrichment (positive macrosegregation) of Ti in the center of the ingots. With the exception of grain size, there was no significant microstructural difference between the two ingots examined. The causes and practical implications of the observed microstructural heterogeneity in the ingots are discussed.IntroductionThe first step in the fabrication of majority of wrought products of aluminum and its alloys is the casting of large ingots or billets of simple shapes (round or rectangular). The sizes of the ingots vary from 10 mm to 450 mm diameter or 25 mm to 780 mm thick. The quality of the finished products is established at the ingot casting stage. This is because the microstructural characteristics, such as secondary dendrite cell size or arm spacing, amount of alloying elements retained in solid solution, macrosegregation, and the characteristics of second phases, produced during casting cannot be reversed by subsequent processing. Up until twenty-five years ago, the effect of as-cast microstructure of large ingots on the structure and behavior of thin sheets (0.34 mm thick) during drawing and ironing processes was incorrectly assumed to be minimal or nonexistent. This was based on the erroneous notion that the thermal treatments and large reduction (>99.94%) and strain that the ingot undergoes during production of the sheets completely destroys the original ingot structure and its inherent heterogeneity. However, the effects of ingot structure can, a priori, be deduced from the observed effects of constituent phase particle size, type and volume fraction on recrystallization, development of texture during annealing and deformation, and earing. In fact, careful examination of the behavior of products produced from different size ingots or castings have shown that the original microstructure of the ingot has a direct impact on the properties and performance of the end products."

Jan 1, 2011

By Dalene Joalet Steenkamp

Excavation of industrial-scale furnaces allows for the systematic study of reaction sequences by identifying the different reaction zones within the furnace. In 2013, Transalloys excavated a 48 MVA submerged arc furnace that was used for silicomanganese production using the ore-based route. The excavation method was reported elsewhere as was observations made in terms of refractory wear and modes of electrical energy dissipation prior to excavation. The paper presented here, reports on the process reaction zones observed during the excavation and subsequent phase chemical analyses of a number of process samples obtained during the excavation. The zones identified were a loose burden zone, a dry coke-bed zone, a wet coke-bed zone, a hard build-up zone, and an alloy zone. The results are compared to observations made in the excavation of an industrial-scale SAF and a pilot-scale SAF in Norway. The presence of the hard build-up zone below one of the electrodes and absence of a slag zone below all three electrodes are unique features of the SAF excavated at Transalloys.

By Guan-zhou Qiu, Shui-shi Liu, Yu-feng Guo, Tao Jiang

"The preparation of high-quality synthetic ruitle from electric furnace titanium slag was systematically investigated by activation roasting followed by acid leaching process. The results showed that impurities such as Ca and Mg in titanium slag can be effectively removed and TiO2 grade of the product was markedly improved by the process. High-quality synthetic rutile containing 88.54% TiO2, 0.42% (CaO+MgO) was obtained under the conditions that roasted with 7.5%(wt) H3PO4 at 1000 oC for 2h, followed by two-stage leaching in boiling dilute sulfuric acid for 2h. Mechanism studies showed that anosovite solid solution and silicate minerals were reacted with phosphoric acid in the roasting process. As a result, titanium components in titanium slag turned into rutile (TiO2) and impurities were transformed into acid-soluble phosphate and quartz.IntroductionWith the gradual depletion of natural rutile and the rapid development of titanium industry in China, the natural rutile reserves cannot satisfy the requirement for production of titanium pigment and titanium sponge. Ilmenite is, therefore, becoming main raw material for titanium industry. However, because of its low TiO2 grade, it generally requires preconcentration to titanium-rich material such as titanium slag or synthetic rutile [1-3].Ilmenite resources are extremely rich in Pan-xi area of China, which account for 90.54% of total ilmenite reserves in China [4]. The titanium slag produced by electric smelting of ilmenite concentrate has high contents of Ca and Mg, and is not suitable as a raw material for chloride process and titanium sponge production. Therefore, upgrading titanium slag to prepare raw material suitable for chloride process and titanium sponge production has important significance for the development of China's titanium industry."

Jan 1, 2011

By Manjie Li, Mingrui Yang, Haijun Peng, Shuxing Qiu, Wei Liu, Shengfu Zhang

It is important to produce and utilize highly reactive coke in order to reduce the energy consumption and CO2 emissions through improving shaft efficiency in blast furnace. The present study aimed to investigate the transformation of iron minerals and properties of iron coke (the coke mixed iron ore fines). Along with the increase of iron ore fines, cold strength displayed a slight downtrend and the pore structure wasn’t inferred to be a major factor affected the properties of iron coke. During carbonization, the majority of mixed iron oxides were reduced to metallic iron by CO and H2 and the degree of metallization achieved to approximately 75%. Nevertheless, produced metallic iron was oxidized by pure CO2 during gasification. Iron coke reactivity index (ICRI) was obviously enhanced and the iron coke strength after reaction (ICSR) drastically decreases, which were also significantly influenced by crystal structure of carbon.

Jan 1, 2015

By A. A. Bustos

A model was developed to simulate the blow-by-blow operation of the converting process. From the weights, compositions and temperatures of all converter feeds the model calculates the composition and tonnage of both converter matte and slag as well as bath temperature at the end of each blow. The development of the model and its application to the converter aisle operation are described. There is good agreement between model predictions and observed results. At the present time the model is being used to investigate different converting schemes and their effect on pay metal recoveries, slag chemistry and temperature of the bath. Future work involves the use of the simulation model as a process control tool for the converting operation.

Jan 1, 1988

By Anja Pfennig, Axel Kranzmann, Phillip Zastrow

"Properties of pipe steels for CCS technology require resistance against the geothermal corrosive environment (heat, pressure, salinity of the aquifer, CO2-partial pressure). To predict the reliability of two different injection pipe steels with 13% chromium and 0.46% carbon (1.4034, X46Cr13) as well as 0.20% carbon (1.4021, X20Cr13) steel coupons were heat treated by comparable routines prior to long term corrosion experiment (60°C, 100 bar, artificial brine close to a CCS-site in the Northern German Basin, Germany). In general higher carbon content exhibits better corrosion resistance with respect to corrosion rate, amount of pits and maximum intrusion depth in the case of local corrosion. At 100 bar hardened steels with martensitic microstructure have the lowest corrosion rates with an average of 0.003 mm/a after 2000 h exposure time. At ambient pressure normalized steels show the lowest corrosion rates, indicating that the corrosion is driven by grain boundaries.IntroductionEngineering a geological on-shore saline aquifer CCS-site (CCS Carbon Capture and Storage [1-3]) corrosion of injection pipe steels may become an issue when emission gasses, e.g. from combustion processes of power plants, are compressed into deep geological layers [4-8]. Typically 42CrMo4 (1.7225, AISI 4140) is used for casing, and for injection pipe the steel X46Cr13 (1.4034, AISI 420 C) or X20Cr13 (1.4021, AISI 420 J) is used. Saline formations are the most favorable storage sites in Germany [9], because of their large potential storage volume and their common occurrence. Leakage of CO2 back into the atmosphere may be a problem in saline aquifer storage, especially around the water level within the borehole. Carbon dioxide corrosion may cause failure of pipelines and wells as known from the oil and gas industry [4,6,10,11, 12].From thermal energy production it is known, that the CO2-corrosion is sensitively dependent on alloy composition, contamination of alloy and media, environmental conditions like temperature, CO2 partial pressure, flow conditions and protective corrosion scales [6-8,13- 20]. Considering different environments, aquifer waters and pressures, the analyzed temperature regime between 40 °C to 60 °C is a critical temperature region well known for corrosion processes as shown by Pfennig et al. [21-23] and various other authors [10,24-28] (figure 1). Here a maximum around 4.7 mm/year was found for the pit intrusion depth of 13% Cr steel X46Cr13. Still this may be predicted by the rather conservative Norsok-Model used in the oil and gas industry to calculate surface corrosion rates of carbon steels [29]."

Jan 1, 2014

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don't allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir's law is discussed for different operating conditions.

Jan 1, 1996

By C. Hennesmann, D. Maijer, S. L. Cockcroft, P. Yo

"Die cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. As part of a collaborative research agreement between researchers at the University of British Columbia and Canadian Auto Parts Toyota Incorporated, work has been underway to predict heat transport and porosity formation in die cast A356 wheels. The basic heat transfer equations have been solved using the commercial finite element package ABAQUS to which specialized routines have been added to predict porosity. Preliminary work on predicting porosity formation focused on using the Niyama parameter as a measure of the probability of porosity. The latest version of the model incorporates a new fundamentally based porosity criterion, which takes into account the effect of hydrogen concentration. The development of this model together with its application to a series of cylindrical test castings as well as a production cast wheel are presented.I. IntroductionDie cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. Microporosity, in particular, is a common defect that can adversely affect wheel quality. The mechanism of microporosity formation in aluminum alloys is complex owing to its dependence on the interaction of a number of phenomena occurring during solidification including the decrease in hydrogen solubility, the decrease in volume, the development of the solidification structure, and the increase in difficulty in interdendritic feeding [1]. As a result, the amount, size, and distribution of microporosity is affected by a large number of casting parameters including thermal variables, melt composition, grain structure, modification, and inclusion content, making optimization by trial-and-error methodologies difficult.The use of criteria functions, based on thermal conditions during casting, offers a relatively simple approach to predicting microporosity. In practical terms, they are useful because they provide a straightforward method of assessing the impact of varying casting parameters on porosity through various thermal parametersl21 such as thermal gradient, cooling rate, solidification time, and solidus velocity. Drawbacks of criteria functions include insensitivity to varying hydrogen concentration and the limitation to qualitative predictions. Consequently, in aluminum alloys, attempts have been made to develop models incorporating the effects of hydrogen gas and microstructure evolution. However, these types of models represent a significant increase in complexity and sacrifice the simplicity and ease of application of the thermally based criteria functions."

Jan 1, 2001

By Marcos V. F. Fonseca, Djalma Souza, Luiz G. X. Borges, Sergio Monteiro, Caroline G. de Oliveira, Ygor M. de Moraes, Janine F. de Deus, Frederico M. Margem

Recently, the natural fibers have been studied as alternative reinforcement material to the use of synthetic fibers. Aiming to improve the properties of natural fibers composites, it is investigated the use of natural fibers fabrics, since they provide multidirectional reinforcement and enables the introduction of a larger fiber volume fraction. In this work, it was investigated the tensile behavior of the epoxy matrix composites reinforced with different volumefractions offabric made of Ramie, a highly resistant lignocellulosic fiber. The specimens were made by pressing the fabric with liquid resin to guarantee total impregnation, and then cutting the fabric in the mold format. Finally ,the fabric layers were placed into the mold with the liquid resin and catalyst. They were cured for 24 h and tested. The results revealed an increase in the tensile strength and almost no effect in the elastic modulus with the increase of fabric volume fraction.

Mar 1, 2017

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By K. Narayana Swamy

Experimental results of 3-phase mixing in a physical model of a CCRL for metals refining, at high levels of bottom gas injection (up to a superfIcial gas velocity (Us) of 12.5 cm/min), are presented. A thermal tracer technique was used to elucidate both longitudinal mixing and interphase heat transfer. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing (D. < 20 cm2/s and D/uL < 0.1) in the CCRL. Interphase mass-transfer coefficients of the order of 0.02 cm/s and higher, are predicted from the measured interphase heat transfer coefficients using the mass and heat transfer analogy. Adequate performance is likely to be possible for an industrial CCRL, based on extrapolation of these results to full-scale conditions.

Jan 1, 1996