Search Documents

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Yuuki Yoshida

Electrolytic manganese dioxide, EMD, is the positive electrode material of primary batteries and the raw material of LMC used as the positive mass of lithium ion batteries and is currently produced by anodic deposition on and harvesting from a titanium anode in acidic manganese sulfate solutions prepared by dissolving high purity of manganese sulfate into sulfuric acid solutions. This paper presents an alternative method of EMD production using a novel anode, Mn2O3 coated titanium, at lower operating temperature than the current process to explore a possibility of manganese recovery from zinc electrowinning solutions. The Mn2O3/ Ti anode prepared by thermal decomposition of a precursor solution containing Mn (II) showed the anodic deposition of MnO2 by constant current electrolysis and the current efficiency was 95% in maximum, while the current efficiency and the crystallographic structure of deposited MnO2 depended on the current density, the electrolysis time, the bath temperature, and the concentration of Mn(II). The deposited MnO2 was successfully harvested from the anode and the recovery rate was 98%.

By Bruno Augusto Batista Ribeiro, Felipe Terra Elias, Wagner Moulin Silva

In the pyrometallurgical production of copper from its sulfides, converting in the Peirce Smith (P-S) Converter is still the most widespread method to obtain white metal and blister copper from the matte. Despite the fact of being a century-old process, it is still possible to achieve improvements in the process, by the use of modern tools, one of the most valuable being numerical calculation and computer-aided simulation. The present study presents three cases in which the angle for the gas injection and the number of working tuyeres are changed during the slag blow phase of the converting process. It was noticed that a decrease of the number of tuyeres, followed by an increase in the injection gas velocity, results in improved reaction volume and less stress to the refractory lining. However, an increase in the amount of copper lost to the slag as oxide is likely to occur.

Jan 1, 2014

By Youqi Fan

Complicated copper oxalate precursor powder was prepared using ammonium oxalate as precipitating agent in the Cu(II)-C2O42--NH3-NH4+-H2O system. The composition and morphology of the powder are characterized by chemical analysis, X-ray Diffraction (XRD), scanning electron microscope (SEM), infrared spectroscopy (IR). The effects of temperature, copper ion concentration, pH value are investigated. It?s indicated by the experimental results that precursor of copper oxalate is prepared below a critical pH value, whereas the precursor turns to be a complicated copper salt combined with NH3 while over the pH value. Probable chemical formula CuC2O4?x(NH3)?yH2O can be assumed which x and y are relation to experimental conditions. Technological parameters, such as temperature, initial copper concentration and solution pH value, have significant effects on particle size, morphology and dispersion of precursor powder. By controlling certain technological conditions, various morphologies of precursor, pie shape, spindle shape and rod shape can be synthesized.

Jan 1, 2009

By A. Lanterne, J. A. Bones, E. Øvrelid, Y. Hu, M. Di Sabatino, F. W. Thorsen

This study presents a new testing method to analyze the bubble content and distribution in quartz crucibles for monocrystalline silicon ingots. Two different types of silica (SiO2) crucibles have been investigated, before and after use during Czochralski (Cz) silicon ingot production for solar cells. Samples have been cut from three different positions along the crucible wall and then investigated by X-ray tomography, optical microscopy and scanning electron microscopy. The unused samples were heat-treated at 1400 °C for 4 h in Ar at 15 mbar. It is observed that the crucible bubbles grow in size and density during the Cz process. More bubbles are detected closer to the inner part of the crucible wall after use in the Cz process. The results also indicate that there are some differences in quality between different crucible producers and that bubble formation and growth are significantly affected by the Cz process parameters, such as temperature and time.

Mar 1, 2017

By M. Okido, H. Yamamoto, T. Sakamoto, R. Ichino, K. Kuroda

"Hydrogen absorption alloy films have been produced by molten salt electrolysis. Lanthanum-Nickel alloy film can be formed on a nickel substrate in KCl-NaCl-LaCb molten salts by electrolysis diffusion process. LaNi5 alloy was formed by mutual diffusion between La ·and Ni after La deposition on Ni substrate. Though several kinds of La-Ni compound existed in deposits, the alloy compounds on Ni substrate changed by electrolysis condition. According to the open-circuit potential measurement in molten salts after La electrodeposition, the formed compounds had a relation to the potential. In the case of the substrate electroplated a cobalt thin film on nickel, LaNi4_5Co0.5 was formed by the electrolysis in the molten salts with lanthanum ions. This ternary alloy film showed better hydrogen absorption behavior in cyclic charge/discharge test in alkaline solution.IntroductionHydrogen storage alloys have attracted attention as the active materials for batteries with the charge/discharge property at ambient temperature. The alloy of nickel and misch metal, mainly consisting of La and Ce, has been commercially 'used as a metal hydride with rechargeable property. In recent years, researches have been developed many kind of new alloys with better hydrogen absorption properties. The hydrogen absorbing alloy ingots are commonly produced by melting method of both metals in furnace, otherwise, prepared by mechanical grinding and metallurgical sintering technique with metal powders. The film is also made by vapor-phase techniques such as sputtering method, ion plating method, etc. ·We have proposed a new method to produce hydrogen absorbing alloy films by molten salts electrolysis technique [1-3]. The hydrogen absorbing film, LaNi5, Mg2Ni and CaNi5, were obtained in this process through controlling the electrolytic condition. The active metals, La, Mg and Ca, are electrodeposited on Ni substrate, diffuse into the substrate and form various kinds of intermetallic compounds. This technique provides a direct process using metal chlorides as resources to produce functional films without using active metals such as La, Ca and Mg."

Jan 1, 2000

By R. Rajiv Srivastava

Brine leaching of a TSL processed zinc-plant residue (ZPR), containing 83.3% anglesite, has been investigated for lead recovery. A prior treatment of ZPR in acid solution did not show any significant effect of acid concentration in zinc dissolution. The study reveals that the solubility limits of PbCl2 is as an important factor with respect to the brine concentration and pulp density in lixiviant. The dissociated sulfate ions hinder the formation of PbCl2 on prolong leaching (above 60 min), while exhibiting the reverse solubility of lead as PbSO4. A 3-step leaching process could yield >92% leaching efficiency when the parameters were maintained as: 10% pulp density in a 250 g/L NaCl solution, 80 °C temperature, and 60 min time. This leaves the insoluble ferrite, sulfides and oxy-sulfates of zinc and lead in the final residue as revealed by the XRD characterization.

By John Anawati

Bauxite residue is an environmentally unfriendly byproduct of alumina manufacturing, produced worldwide in large quantities. This material contains 50– 100 ppm of scandium, a critical material for the production of stronger, weldable, corrosion resistant, and heat tolerant aluminum products. Aircraft manufacturers are particularly interested in Al–Sc alloys because of its ability to form weldable alloys that could potentially reduce aircraft weight by 15–20%. Because of its abundance and low cost, bauxite residue has the potential to be used as an efficient feedstock for valorization processes to recover its scandium content, while in turn degrading this problematic waste. In this project, we developed an efficient process to recover scandium and rare earth elements from a Canadian bauxite residue with high extraction yields, using industrially scalable and economical techniques. The process employs a modified version of sulfuric acid leaching and subsequent impurity removal by selective precipitation. This article outlines the current progress and design rationale in the development and optimization of this innovative and sustainable recovery process.

By J. P. R. deVilliers

A procedure is described whereby gold-containing calcined concentrates and leach residues from refractory gold ores are smelted with carbon to form a small amount of metal. The gold is liberated upon smelting, and is collected in the molten metallic phase, which is easily separable from the slag. The metallic phase consists of approximately 1 to 15 per cent (by mass) of the material after smelting, and the gold content is generally upgraded by a factor of greater than 6 compared with that of the original roasted material. Recoveries better than 95% have routinely been achieved. The quenched metal contains predominant Fe-Ni alloy, as well as minor Fe sulphides and Cu-Fe sulphides. Trace amounts of Fe-Ni arsenide and Au-Cu alloy are also present. The gold content of the metallic phase can be increased further by oxidation of the hot metal in the presence of silica or slag. This will reduce the amount of metal, and will concentrate the gold in a smaller volume. The metallic phase can then be treated hydrometallurgically to recover the nickel and the gold.

Jan 1, 1989

By Chen L. Lin

Scientific visualization is an ideal methodology for investigating complex phenomena that are characterized by large amounts of data. Furthermore, it is invaluable in the study of processes that evolve in time. Scientific visualization relies heavily on computer graphics, image processing and video technologies. Specific applications of scientific visualization in the minerals and materials processing fields that are considered in this paper include: 1) applied CT technology for multiphase materials and minerals, 2) time averaged density profla in air- sparged hydrocyclone (ASH) flotation and 3) dynamic motion analysis of ball mill grinding.

Jan 1, 1993

By Jewel Gomes

Green rust is an important intermediate in oxidative transformation of Fe(II) phase. This unstable compound contains a mixture of ferrous and ferric hydroxides that belong to a family of minerals known as layered double hydroxides (LDH). Its general formula is [FeII(6-x) FeIIIx (OH)12]x+[Ax/n-*yH2O] x-, where A is an n-valent anion mainly Cl-, CO3-2 and SO4-2, and in which either the bivalent or the trivalent iron can be replaced for other trivalent or bivalent metal ions. It was first identified as corrosion product, later in soils as a product of interactions between microbes and metals in soils. Due to its high reactivity, it is used in the reduction of organic and inorganic compounds, As removal, and the treatment of acid mine drainage. In this paper, we described the method of electrochemical generation of green rust, its characterization by XRD, SEM and FT-IR, and its implications to electrocoagulation.

Jan 1, 2009

By A. V. Tarasov, V. M. Paretsky

"Based on theoretical and experimental studies into the specific features of the mechanism, kinetics, aerodynamics and heat transfer parameters of the flame-type oxidation of metal sulfides in a stream of technical-grade oxygen, a three-dimensional deterministic mathematical model of an oxygen-flame smelting furnace has been developed on the basis of the zonal method for computation of heat exchange. The model is presented in the form of equations taking into consideration the radiation component of the selective radiation, the convection component of mass transfer between the space and surface zones, heating of charge particles due to heat conductivity, accretions formation on a multi-layer refractory lining with inserted cooling elements. The adaptation of the model for a full-scale furnace has demonstrated the possibility for its use for computation of main smelting process parameters. Multifactor model investigations were conducted and the results obtained were applied using statistical methods for development of a simplified computational regression model describing the interrelation of the main output parameters: temperatures of flame, lining, slag and off-gas; heat fluxes to the lining; thickness of accretions; heat removed by cooling elements; copper content of matte. On the basis of this model, a block diagram of the algorithm was developed for control of the thermal conditions of the furnace, as well as the control algorithm itself.IntroductionThis paper presents the results of an integrated modeling and development of principles for control of copper smelting process using as an example the oxygen-flame smelting process (KFP) for treatment of sulfide concentrates at the Kovoguty Krompahy copper smelter (Slovakia) with a capacity of 20,000 tpy of copper."

Jan 1, 2001

By I. Kim, J. C. Choi, W. D. Cho

"The effect of yttrium addition on the oxidation behavior of Fe3Al intermetallic compound was investigated in the range of temperature 800 to 1100 °C in 0.2 atm 02 in terms of oxidation rate and oxide adhesion. The oxidation rate of alloys, Fe-14.3 wt% Al and Fe-14.1 wt% Al-0.3 wt% Y, was nearly identical and the parabolic rate constant calculated as a function of temperature is Kp=5128 exp[-39506(cal/mol)/RT] mg2/cm4 hr.Rapid cooling and ultrasonic stress tests were carried out to test adhesion of scale formed on the alloys. While the oxide layer formed on the Fe-Al alloy without Y was found to be fragile and detached easily during the tests, the oxide layer formed on the Fe-Al alloy containing Y was protective, dense, and adhesive. The following two mechanisms were proposed to explain the adhesion improvement of Ah03 formed on the Fe3Al containing yttrium : (1) the addition of yttrium decrease generation of growth stress in alumina scale because the preferential diffusion of yttrium through grain boundary in alumina scale prevent internal oxidation of Al, one of main causes of growth stress, and (2) the second phase formed on the oxide scales prevents crack propagation through the scales, leading to better mechanical stability of the oxide scales.IntroductionIron aluminides have attracted the attention of many researchers as a candidate for use at high temperature because of their excellent oxidation resistance due to the formation of protective alumina scale. In order to resist aggressive environments at elevated temperatures, oxide scale formed on iron-uluminum alloy must satisfy the following three requirements : (1) thermodynamic stability (2) slow growth rate (3) adherence on substrate. According to Wallwork and Hed [l], the most suitable alloys for high temperature application are Fe, Ni, and Co alloys with the protection of Si02, Cr203, and Ah03 scales. While chromium oxide can vaporize as Cr03 above 1000 °C and silicon oxide may form low melting silicate [2,3], Alz03 has a high melting point and is the most stable among the three oxides thermodynamically [6]. In this respect, iron aluminides forming alumina seem to be most suitable for use at high temperature. However, alumina scale formed on the iron aluminum alloys tends to be easily spalled during oxidation due to the combination of growth stress and thermal stress."

Jan 1, 1998

By Tatsuro Ariyama, Michitaka Sato, Atsushi Sakai, Sumiyuki Kishimoto, Ryota Murai

"In order to achieve high pulverized coal injection operation in a blast furnace, optimization of the injection lance arrangement was carried out using an experimental furnace and mathematical models. To increase the injection rate of pulverized coal, it is required to raise the combustion efficiency of pulverized coal. It became clear that multi-point injection and the lance arrangement to avoid interference among the coal streams injected were so effective in increasing combustion efficiency. With these findings, the eccentric double lance arrangement has been newly developed.At NKK, Fukuyama No.4 Blast Furnace, after the improvement of the lance arrangement, the maximum injection rate reached up to 230 kg/thm and an average monthly record of 218 kg/thm was successfully achieved.IntroductionFrom the viewpoints of reducing the production cost of pig iron and prolonging coke oven life, high pulverized coal injection over 200 kglthm is actively pursued by ironmaking industries[1-2].Coal particles injected into the blast furnace are consumed by combustion in the raceway and also in-furnace reaction like solution-loss reaction (C + CO2 = 2CO). The amount of coal consumed by the latter process is determined by the carbon balance in the blast furnace and there is a limit. Therefore, to increase the injection rate, it is desirable to improve the combustion efficiency in the raceway. For these purposes, the optimization of the lance arrangement was examined by a hot model and mathematical models."

Jan 1, 1996

By Christian Redl

"The Lattice Boltzmann Method (LBM) solves fluid dynamics problems based on a discrete mesoscopic approach. It is based on the Lattice Boltzmann equation which is a special discretisation of the continuous Boltzmann equation. Its principle advantage is that it can handle complex physical phenomena (like interaction between different components and surface effects), complicated boundary and initial conditions very well, free from many gridding and stability constraints that plague conventional numerical methods used for fluid flow simulations. Complex structures like porous media can be resolved directly. The LBM algorithm has a simple structure and acts locally, which is favourable for parallel computing. Its potential for metallurgical process simulation is demonstrated in the present study which is concerned with the simulation of the fluid flow in a copper winning electrolysis cell. The electrolyte is modelled as the carrier fluid and the oxygen is considered via a so called active scalar equation. The modelling of buoancy, momentum exchange and the free surface requires special effort. The results of the simulation are validated against experimental data obtained by Laser-Doppler-Anemometry. Despite the simplifications made, good agreement between the simulation and the experiments was found.IntroductionThe hydrodynamics in an electrometallurgical cell is a complex, highly non-linear phenomenon. It includes the simulation of a two component system with high density ratio, gravity driven flow and a free surface. A general solution to this problem is currently unknown.The flow field is a result of the combination of various hydrodynamic effects [18]. Metal deposition at the cathode yields in a decrease in the ion concentration, which reduces the density of the electrolyte. At the anode molecular oxygen is formed as a consequence of the oxidation of water molecules. The oxygen is solved in the electrolyte and again the electrolyte density is decreased. Both effects lead to a free upwards directed convective flow, refered to as natural convection."

Jan 1, 2001

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

The equilibrium experiments between the FeO-SiO2-MnO-TiO2-V2O3-Cr2O3-MgO slag system and solid pure iron were performed to investigate the vanadium and chromium distribution ratio under Ar atmosphere. The influence of w(FeO), w(V2O3) and w(Cr2O3) in slag on vanadium and chromium distribution ratios were studied at 1653 K. The experimental results were compared with calculated distribution ratios based on molecule and ions coexistence theory. Both of them showed that higher FeO content in slag would improve the distribution ratios of V and Cr between slag and hot metal. The distribution ratio of Cr or V increased with the increase of Cr2O3 or V2O3 content, respectively. To optimize the oxidation of V and Cr from hot metal, a high oxidizing slag and suitable content of Cr2O3 and V2O3 in the slag were recommended. The results provided reference for the further study on the extraction of V and Cr in VTi magnetite.

Jan 1, 2016

By Mark Cross, Hadi Abou-Chakra, Nicholas Christakis, Mayur K. Patel, John Baxter, Ugur Tiizful

"In recent years significant effort has been put into using continuum mechanics for the description of granular flows. Although these models are partially successful in capturing some flow characteristics, they lack essential information on material properties, which are needed to account for the interactions between different particles. Thus, they are incomplete and can not be used to describe processes such as hopper filling/emptying and pneumatic conveying, where particle-particle interactions can lead to phenomena such as segregation, degradation and agglomeration. In this paper, a 3-D unstructured finite-volume framework is presented, which employs interface tracking techniques to solve for the individual material components of the granular mixture in the bulk and thus, determine the material-air interface. Various transport processes, arising from the micro-mechanical properties of the different particle species in the granular mixture, can be obtained through kinetic theory. The transport coefficients of each of the individual species can be determined and analysed in a micro-mechanical framework and the transport process parametrised in the form of constitutive models. These models provide the continuum theory with information on the micro-mechanics.This work describes the continuum framework and the micro-mechanical parametrisations, which are used to describe the processes and interactions at the microscopic level. Numerical simulations and comparisons with experimental data are then presented for the case of binary granular mixtures and conclusions are drawn on the capability of the model to realistically predict and quantify the main characteristics of granular flows."

Jan 1, 2001

By Guolin Zheng, Tiejun Chun, Jian Pan, Deqing Zhu, Xianlin Zhou, Dong Chen

"The high temperature oxidizing-chloridizing roasting is one of useful methods to separate nonferrous metals from pyrite cinder and metallurgy slag. However, as one kind of main nonferrous metals in pyrite cinder and metallurgy slag, copper’s chlorination behavior is not demonstrated. In the present study, chlorination behaviors of CuO, Cu2O and CuS at the temperature range of 1025-1175 ? in air by simulating the chloridizing roasting process of pyrite cinder and metallurgy slag have been investigated. It is shown that Cu2O and CuS is much easier to remove, CuO is refractory to remove. In addition, the presence of SiO2 and CaO increases the Cu removal rate from CuO while the presence of SiO2, Al2O3, CaO and MgO decreases the Cu removal rate from Cu2O. Fe3O4 influences the Cu removal rate from CuO and Cu2O positively.IntroductionAs two kinds of significant secondary resources, pyrite cinder and metallurgy slag contain not only abundant iron but also considerable copper, lead, zinc etc. Millions of tons of pyrite cinder and metallurgy slag were discharged from nonferrous metal and chemical industries annually [1, 2] in China. The pyrite cinder and metallurgy slag are formed by roasting of minerals at a high temperature, so the properties of them are distinctly different from the natural iron ores, and the iron in them is closely associated with copper, lead, zinc and other nonferrous metals. High-quality pyrite cinder and metallurgy slag containing high iron and low impurities can hardly be obtained, leading to their low utilization degree [3]. Chlorination is characterized by the high reactivity of chloridion, the high volatility and low melting point of metal chlorides, and the big differences in the formation of metal chloride. Therefore, chlorination is widely applied in extraction metallurgy."

Jan 1, 2012

By Jie Li, Shu Yang, Zhongliang Tian, Xun Hu, Yanqing Lai, Shaolong Ye

The electrolyte with high solubility for Sc2O3 is very important to realize the preparation of Al-Sc master alloy by the molten salt electrolysis. The solubility of Sc2O3 in K3AlF6- Na3AlF6-AlF3 melts is determined with an isothermal saturation method. The effects of KR (ratio of K3AlF6 to K3AlF6+Na3AlF6), the concentration of Al2O3 and the temperature on the solubility of Sc2O3 are also investigated. The results indicate that the solubility of Sc2O3 in K3AlF6-Na3AlF6-AlF3 melts increases and then decreases with KR increasing. The solubility of Sc2O3 is 8.698 wt.% in (K3AlF6-Na3AlF6)(KR25%)-18 wt.%AlF3 melts at 940℃. The effect of temperature on the solubility is little, and the values are 8.575 wt.% and 8.762 wt.% respectively when the temperatures are 930℃ and 960℃. The solubility decreases from 8.809 wt.% to 7.058 wt.% as the concentration of Al2O3 increases from 1.5 wt.% to 5.0 wt.% at 950℃.

Jan 1, 2015

By D. A. Salinas G., A. H. Castillejos E.

Pachuca tanks are commonly used in the hydrometallurgical industry to carry out leaching operations. The fluidynamic characteristics of the liquid phase, resulting from the injection of gas into the draft tube, are important to achieve the complete suspension of the mineral particles and has a decisive influence in the mass transfer processes occurring in this reactor. This study investigated the effect of different design and operating characteristics on the liquid velocity field. using a laboratory-scale Pachuca tank. The transparent model was filled with water, and air was injected through the bottom in the absence of mineral particles. The liquid velocities over the whole reactor were measured under several experimental conditions using particle image velocimetry (PIV). This technique allowed to obtain a very detailed picture of the liquid motion even in the draft tube, as long as bubbles were absent from the measured field of view. The experiments have shown that the liquid velocities increase with increasing the draft tube to tank diameters ratio, the distance from the conical bottom to the draft tube entrance, or the gas superficial velocity. On the other hand, an increase in the water level with respect to the draft tube outlet caused a decrease. A mathematical model, which used the no-slip model, to calculate the variation of axial effective density along the two-phase region, was found to predict liquid velocity fields which agree very satisfactory with the experimental results obtained under all the conditions studied.

Jan 1, 1999