Search Documents

By I. G. L. Sinclair

The Selbaie deposit is located in northern Quebec. It is comprised of three distinct, but genetically related, Cu-Zn-Ag ore bodies which also contain economically significant amounts of Au. The deposits are Archean in age and volcanogenic in origin. At Selbaie, ore microscopy has been employed to aid in planning of ore beneficiation methods and to monitor the ongoing performance of the concentrator. Examples of both types of study are described. Early in the life of the mine, excessive amounts of Zn appearing were found to be appearing in the Cu concentrate. Microscopic examination of concentrates showed that this was being caused by the presence of coatings of supergene chalcocite on sphalerite grains. Fine coatings of supergene galena and chalcopyrite were also observed on some sphalerite grains. The presence of Ag and Au in the ores makes an important contribution to the revenue of the mine. The various modes of occurrence and mineralogical relationship of these two metals are described and discussed. Monitoring of the ongoing concentrating process at selbaie is done by qua-litative and quantitative examination of products collected at various points along the circuit. Causes of such problems as excessive loss of metals to the tailings or inefficient recovery of individual metals, can often be identified and possible solutions proposed.

Jan 1, 1989

By Jianguo Yin, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade iron ore with phosphorus (LGIOWP), a raw and wasted industrial solid material was used as an adsorbent to remove Pb(II) from wastewater. The effects of initial pH value, adsorptive time, initial Pb(II) concentration, adsorptive temperature and LGIOWP dosage on the Pb(II) removal efficiency were studied. The results show that the Pb(II) removal efficiencies exceed 99.4% and Pb(II) concentrations are less than 0.30 mg/L under the conditions of pH value 7.0, adsorptive temperature 50 oC, adsorptive time 30 min, initial Pb(II) concentration 100 mg/L, particle size <0.25 mm, adsorbent dosage 5 g/L and stirring speed 260 r/min. After Pb(II) removal reaction, the Pb(II) concentrations of wastewater completely accord with the requirement of national discharge standards of pollutants from lead and zinc industries (GB 25466-2010) (TPb= 0.5 mg/L) in China. Therefore, it can be concluded that LGIOWP is a new low-cost adsorbent which is suitable for the adsorption of Pb(II) from wastewater.

Jan 1, 2015

By Hiroyuki Matsuura

The effects of P20S or Na20 addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at 1773K by isotope exchange methodl-6_ The rate constant decreased with increasing P20S content of molten oxides and the residual rate constant was observed at high P20S content On the other hand, the rate constant increased with increasing Na2O content for FexO-SiO2 melts. The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By David Melgaard

A significant emerging recycling, waste minimization problem stems from legacy waste from the nuclear weapons program and from production of power using nuclear fuel. Premium quality metals used in nuclear plants become contaminated, making them unsuitable for reuse. Consequently, decontamination studies were conducted to evaluate the decontamination capacity and partitioning effeetiveness of Electroslag Remelting (ESR). Eight laboratory melts were conducted to evaluate the efficacy of using ESR to transport radionuclides from the liquid metal phase to the liquid flux or slag phase. To determine the decontamination effectiveness, several surrogate compounds for uranium, plutonium and other fission products were added to the melts. During the melts, the melting rate was varied, typical slag additives were used, and two different slag compositions were evaluated. The resultant post-test ingots and slag were then analyzed to determine the partitioning of the surrogates. ESR generally proved very effective in removing contaminates from the metal with a few noted exceptions. -

Jan 1, 2003

By G. B. Harris

Jaguar Nickel Inc. is developing the Sechol Nickel-Cobalt Laterite Project in Guatemala, Central America. Recognizing the potential advantages offered by chloride brine chemistry, Jaguar, at the facilities of Process Research ORTECH Inc, Mississauga, has developed an Atmospheric Chloride Leaching Process using a mixed chloride lixiviant to recover the nickel and cobalt, whilst leaving the majority of the iron and magnesium in the leach residue. Subsequent solution purification and mixed nickel/cobalt hydroxide product recovery is by standard precipitation methods, using recycled caustic magnesia, with a final stage of pyrohydrolysis of a portion of the concentrated magnesium chloride brine for recycling both the caustic magnesia and chloride lixiviant. The flowsheet that has been developed also offers opportunities for by-product recovery and efficient, environmentally clean process effluent management. The paper discusses some of the early leaching results in the context of strong chloride brine chemistry, with emphasis on how the controlling of water activity, hydrogen ion activity and chloride concentration permits the selective leaching of nickel and cobalt from an iron-magnesium matrix. Keywords: nickel, cobalt, iron, magnesium, Sechol, Guatemala, chloride, pyrohydrolysis

Jan 1, 2004

By G. A. Bala

As part of ongoing research to define mechanisms of microbial enhanced oil recovery (MEOR), this work describes the activity of Bacillus l1chen1formis JF-2 (ATCC 39307) Mosurfactant against crude oils with varying compositions. Surfactant based MEOR improves oil recovery by lowering the oil/brine interfactal tension (IFT) therefore permitting oil to be displaced or solub1lized into the aqueous phase.? MEOR is an Enhanced Oil Recovery (EOR) process which allows for the introduction of chemical and miscible fluids, in the form of microbial metabolic end-products, through the injection of microorganisms into the reservoir or stimulation of indigenous reservoir microbial populations. These microorganisms represent a replenishable in situ source of acid, gas, biopolymer, solvent, or surfactant products which can be. supported and manipulated by the addition of simple and inexpensive nutrients to enhance the recovery of oil. Microbially mediated surfactant production represents one mechanism of MEOR. Bacillus licheniformis JF-2. has been used in a mode 1 MEOR system based on Berea sandstone cores (permeabilly .85 to 400 md) to examine surfactant based MEOR of medium to heavy crude oils (API gravity 38.1° to 17.5°). Enhanced oil recovery was achieved with all oils tested using either cell free culture supernatants or microbial suspensions as injectants with no detrimental effect to the oil. Spatial distribution of cells following mf?crobtal flooding was analyzed with scanning electron microscopy. Data indkate complete distribution of cells with a predominance of organisms located distal to the point of injection. There appears to be no sign:if1cant recovery trend with respect to oil composition.. The biosurfactant produced by Bacillus lichen1form1s JF-2 lowers the interfacial tension of all oils tested equally well.

Jan 1, 1991

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994

By I. Gaballah

Decontamination of synthetic solutions of PbC12 containing 10, 100 and 1000 ppm of lead, using chemically treated barks had been studied. The percentage of !cad cations&apos; removal from solutions depends upon the pH and the initial concentration. About 99 % of the initial lead content can be removed at pH of about 3.5, 5.5 and 6.5 for initial concentrations of 10, 100 and 1000 ppm respectively. The maximum retention capacity of the treated bark is about 83 mg of lead per gram of modified bark. Bark loaded with lead had been analyzed by Infra Red spectroscopy. It seems that lead reacts with hydroxyl groups of the phenolic constituents of the bark. On the other hand, the removal of a lead cation by the bark leads to the release of two H+. This seems to show that the removal of lead could be interpreted as an ion exchange with hydrogen belonging to the hydroxyl groups of the modified bark.

Jan 1, 1994

By N. Pradhan, B. K. Mishra, B. D. Nayak, B. K. Mohapatra, R. K. Mohapatra

"Present study is about use of a group of Iron[Fe(III)] Reducing Bacteria (IRB) to convert the goethite (a-FeOOH) present in the original lateritic Nickel ore to magnetite under an anaerobic condition and subsequently release the bound Co(III) and Ni(II) through leaching. The lateritic Nickel ore contains 0.8% Ni, 0.049% Co, 1.92% Cr, 0.32% Mn and 50.2% Fe. An anaerobic dissimilatory Fe(III) reducing bacterial consortium capable of using acetate as carbon source (electron donor) and lateritic ore as terminal electron acceptor, changes the initial light brown color of the ore to dark brown. The change in color is due to the conversion of goethite to magnetite, which was confirmed by XRD. When the IRB treated sample was subjected to both bioleaching and acid leaching, it shows a greater recovery of Nickel and Cobalt values as compared to untreated original lateritic Ni ore. Further a magnetic separation method was used to separate the magnetic part of the treated lateritic ore and subjected to acid- and bio-leaching for better recovery of Nickel and Cobalt.IntroductionIt has been known that micro-organisms have the potential to reduce metals but more recent observations have shown that a diversity of specialist bacteria and archaea can use such activities to conserve energy for growth under anaerobic conditions [12]. Natural Fe(III) oxides are high in surface area and are reactive [1]. Fe (III) oxides adsorb a wide range of metal cations and anions by complexation to surface hydroxyl groups [17], and function as the primary redox buffering solid phase in many sediments and subsurface materials [5].Recently a number of bacteria have been isolated based on their ability to use metal ions, including Fe(III), as electron acceptor under anaerobic conditions. These are capable of producing energy by coupling the oxidation of organic compounds to reduction of Fe(III). Iron[Fe(III)]-Reducing Bacteria (IRB) have been isolated and identified from a wide variety of environments including freshwater and marine aquatic sediments and submerged soil [8]. The biogeochemical cycle of iron is linked to those of the trace metals, as many trace metals coassociate with Fe(III) oxides or reduced iron phases (e.g., magnetite, siderite, or iron sulfide). IRB can utilize Fe(III) oxides as terminal electron acceptors for respiration [18]; thereby reducing all or a fraction of the solid. The reductive portion of the iron biogeochemical cycle in non-phototropic environments (e.g., sediments and subsurface materials) is driven by the direct enzymatic reduction of Fe(III) oxides to Fe(II) by dissimilatory iron reducing bacteria [13,14]."

Jan 1, 2009

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By W. G. Davenport

Chapter 1 showed that flash smelting is a key step in extracting copper from sulfide ores. It also showed that there , are two versions of flash smelting: (a) Outokumpu flash smelting, which uses oxygen-enriched air blast and injects dry feed downwards into a hot furnace (b) lncoflash? smelting, which uses industrial oxygen blast and injects dry feed horizontally into a hot furnace. This chapter describes Outokumpu flash smelting.

Jan 1, 2001

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By D. H. Magoon

The zinc smelter of Cominco Ltd. at Trail, B.C. Is the largest In the western world. A total of 550.000 tonnes of concentrate are proceed at the smelter annually. Approximately 80% of the zinc concentrate is roasted and the remainder Is treated by aqueous oxidation preaaure leaching. The zinc concentrate roasting and sulphur dioxide gas processing plants have undergone many changes over the years. This paper describes the processes and equipment currently used for concentrate roasting, S02 gas cooling and cleaning, mercury removal, sulphuric acid production liquid S02 production, and tall gas S02 scrubbing. The recent Installation of an advanced process control system for the operation of these Integrated processes Is also described.

Jan 1, 1990

By Joerg Hammerschmidt, Marcus Runkel, Andreas Wirtz, Kent Pope

"Fluidized bed reactor systems in the minerals industry have been progressively developed and widely implemented over a period of more than sixty years for a multitude of process applications. Their versatility is manifested in calcining, roasting and combustion treatment of minerals including solid fuels. Experiences from metallurgical processes have expanded to new applications in the oil shale processing, biomass combustion and renewable energy sector. This paper focuses on the most important aspects of fluidized bed technology for a variety of Outotec processes. Energy recovery is a major topic for all applications and will be addressed, as well as environmental aspects, particularly regarding the off-gas treatment. Outotec is one of the pioneers of roasting and the fluidized bed process including gas cleaning and sulphuric acid production where applicable. Process development is strongly supported by significant investment in R&D, thus enabling process adaptation and scale-up to meet specific customer/market requirements.Introduction to Fluidized Bed TechnologyThe early days of fluidized bed technology were characterized by the use of bubbling fluidized bed reactors (BFB). This technology was popular for roasting zinc and copper ores. The introduction of circulating fluidized bed technology led to increased plant capacities and improved process control for the traditional processes. Furthermore, the technology has been applied in many other industries, including the renewable energy industry, which will be part of this design and process comparison. The paper starts out with the fundamentals on particle fluidization as the main common design parameter, leading to the importance of heat recovery and offgas treatment.In fluidized reactor systems, the particle concentrations can reach several hundred kilograms per cubic meter of fluidization gas. This high solid concentration leads to large surface areas and enables direct contact of gas molecules with particle surface molecules. Excellent conditions for enhanced heat and mass transfer thus provide nearly ""ideal"" heat exchange conditions and better reaction kinetics. The bubbling bed exhibits a better heat transfer coefficient within the bed in comparison to the circulating fluidized bed (CFB). The different conditions of gas velocities and solid concentrations allowing the classification of fluidization reaction regimes are shown in the Reh diagram in Figure 1."

Jan 1, 2014

By J. Y. Foley

Platinum-group elements (PGE) are preferentially associated with chromian spinels, including high-iron chromite, magnesian-chromian hercynite, and chromian magnetite in clinopyroxene-rich upper stratigraphic portions of the Tonsina ultramafic complex in southern Alaska. Ratios of Pt:Pt+Pd are proportional to chromium content in the associated chromian spinels. The maximum PGE content of geochemical rock samples from Dust Mountain is greater than 20.000 ppb (>0.6 oz/ton) with minor gold values. The maximum PGE content of tabled chromite concentrates is 3.430 ppb (0.1 oz/ton) at Dust Mountain. 1.029 ppb (0.03 oz/ton) at Sheep Hill, and 1,749 ppb (0.051 oz/ton) at Bernard Mountain. High-iron chromite at Dust Mountain yields tabled chromite concentrates with Cr:Fe ratios between 0.5 and 1.2. Lower PGE contents are found in more chromium-rich chromitites from Sheep Hill and Bernard Mountain that yield concentrates with Cr:Fe ratios between 1.0 and 2.8. Platinum-group minerals include amalgams. arsenides. PGE alloys, and sulfides. These minerals are between 3 and 40 microns in size and are concentrated along grain boundaries and fractures of metasomatically and hydrothermally altered chromian spinel grains.

Jan 1, 1987

By K A. Pericieous

"Magnetic fields have many actual applications in the metals processing industry. Externally applied magnetic fields give rise to electromagnetic (Lorentz) forces formed by the cross product JxB, between the induced current density J and the magnetic field density B. When the metal is in liquid form, the Lorentz force generates motion in the fluid which in applications of practical interest becomes turbulent. In modelling terms, the Lorentz force appears as a source in the momentum equations. In addition, the induced current generates heat (Joule heating) in the metal that is in proportion to J2, with a corresponding source of heat in the energy equation. Whether as heat or as a force, these effects represent action at a distance - a most useful attribute when dealing with hot metal. The Lorentz force is used to stir solidifying alloys, pump liquid metal in conduits, dampen the flow in the meniscus of a continuous caster, levitate metal drops, induce artificial gravity conditions in suspensions or contain liquid metal. Elsewhere, the Lorentz force may be a by-product of some other operation, so leading to wave excitation in aluminium electrolysis cells, or altering the shape of the weld pool in arc welding. Joule heating is most commonly used with applied AC fields, to melt metal in induction furnaces.The author and his colleagues have been involved in the modelling of most of these processes in the past decade. Modelling is not however straightforward, since most of the examples mentioned represent genuine multi-physics challenges. There is a strong coupling between the flow field and electromagnetic field. The addition of a dynamically varying metal free surface and the moving solidus front means the flow, heat and electromagnetic fields need to be computed simultaneously. In situations involving metal containment, the metal free surface position is governed by the interplay of gravity, Lorentz force, surface tension and fluid inertia. Since all the interesting effects often happen in thin boundary layers at the surface due to the skin effect, mesh generation and mesh control during the computation become non trivial problems that need to be addressed. This paper presents a review of numerical methods used to model droplet levitation, semi-levitation melting and cold crucible induction melting of metals. The first method is based on spectral collocation techniques and the second is the traditional FV approach. Steps taken to validate the computations and typical transient results are also given."

Jan 1, 2001

By G. Kyle Green

Zirconium chlorinator residues contain an array of rare earths, scandium, unreacted coke, and radioactive thorium and radium. Because of the radioactivity, the residues must be disposed in special waste containment facilities. As these sites become more congested, and with stricter environmental regulations, disposal of large volumes of wastes may become more difficult. To reduce the mass of disposed material, the U.S. Bureau of Mines (USBM) developed technology to recover rare earths, thorium and radium, and unreacted coke from these residues. This technology employs an HCl leach to solubilize over 99% of the scandium and thorium, and over 90% of the rare earths. The leach liquor is processed through several solvent extraction stages to selectively recover scandium, thorium, and rare earths. The leach residue is further leached with an organic acid to solubilize radium, thus allowing unreacted coke to be recycled to the chlorinator. The thorium and radium waste products, which comprise only 2.1% of the original residue mass, can then be sent to the radioactive waste facility.

Jan 1, 1995

By A. Kontopoulos

The Olympias Mine in Northern Greece is producing an extremely refractory gold-bearing arsenical pyrite concentrate, containing on the average 41 3 S, 40 3 Fe, 10-12 3 As, 25 ppm Au and 35 ppm Ag. During the process selection stage, more than a dozen alternative technologies? were considered and an in-depth analysis was prepared for the three most promising, ie roasting, pressure oxidation and biological oxidation. Detailed capital and operating cost estimates were prepared, based, where appropriate, on laboratory and pilot-plant tests. A number of criteria was used for process evaluation and selection, including capital and operating costs; environmental impact, gold&apos; recovery, stage of development, etc. Based on the above evaluation, the Sherritt Pressure Oxidation Process was finally selected. A detailed description of the process selection stage, supported with laboratory and pilot-plant test results on many of the processes considered, will be? presented.

Jan 1, 1989

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Ousan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By Ari JokiIaakso

Three different sulphidic raw materials were treated in a laboratory scale laminar flow fur-nace simulating suspension smelting conditions. The materials were a pure chalcopyrite concentrate, a high-antimony concentrate (tetrahedritic), and crushed copper mattes. The gas preheating temperatures were 500 -1 100°C ana the atmospheres ranged from N2 to N2 -75 % O2, Two particle size fractions were used for the concentrates with x = 20 -38 um and x = 62 -74 um, and three for the granulated copper mattes with x < 37 um, x = 62 -88 um, and x = 125 -177 um. Scanning electron microscopy combined with energy dispersive analysis and backscattered electron analysis was used for determining the morphology and the mineralogy of the reacted particles. Fragmentation of the particles were observed in all materials during the flash oxidation, the conditions depending on the iron and sulphur content and the original particle size fraction of the material. The melting and/or reaction stages of the particles in different conditions were studied from powder samples. Polished sections were examined in order to follow the development of porosity and the mineralogy of the particles.

Jan 1, 1989