Search Documents

By W. G. Davenport

Chapter 6 examined autotherrnal smelting of pure chalcopyrite concentrate with 50 mass% O2-50 mass% N2 blast. It showed that production of 1500 K products with this blast requires: 181 kg of pure oxygen 337 kg of air per tonne, of concentrate. It also showed that the grade of matte produced with this blast is 58% Cu. This chapter re-examines autotherrnal smelting by asking: (A) WHAT COMPOSITION BLAST (MASS% 02 -MASS% N2), 298 K, WILL AUTOTHERMALL Y PRODUCE 65% Cu MATTE 1500 K FROM PURE CHALCOPYRITE CONCENTRATE? (B) HOW MUCH PURE OXYGEN AND AIR WILL BE NEEDED? These are important questions for flash? smelting because furnace operators usually want to send specific composition matte to converting. This chapter shows how a specified matte can be produced autotherrnally with 298 K oxygen-air blast. Later chapters show how it can be done with hot blast, hydrocarbon combustion, different concentrates etc.

Jan 1, 2001

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.

By Na Wang, Chao Du, Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Niobium aluminides were directly synthesized by a sodiothermic reduction process of NbC15 - AlCb which was dispersed into LiCl - KCl - NaCl - CaCb melts. The melt supplied a homogenous reaction medium which was substantially beneficial to the co-reduction of Nb and Al to form niobium aluminides in situ. The reduction was performed at 500°C for 4 hours. The products were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). The corresponding results indicated that niobium aluminides powders were successfully synthesized.1. IntroductionNiobium aluminides have received considerable attention as high-temperature structural materials, due to their high melting points, relatively low density, high strength, excellent oxidation and creep resistance [1-4]. Figure 1 shows that there are three intermetallic compounds in the Nb - Al binary [5], which includes Nb3Al (A15 structure, Cr3Si type), Nb2Al (D8b structure, cr-CrFe type) and NbAb (D022 structure, TiAb type). These niobium aluminides have been used in turbine blades or in stationary gas turbines [6-8]. However, despite their attractive features, the ir applications are still limited by the long and costly fabrication process [9, 10].Niobium aluminides were industrially fabricated by the mechanically alloyed process [11-13]. Traditionally, niobium is extracted from Nb2O 5 or K2NbF7 by a metallothermic reduction process while aluminum is produced by the Hall-Heroult process of Ah03 electrolysis. Based on the extraction of Nb and Al, respectively, niobium aluminides is synthesized by a mechanical powder alloying process. The present process for making niobium aluminides requires a set of complicated equipment, has high production cost and time consuming [14, 15].The purpose of this work is to present the simple, economic and direct synthesis of niobium aluminides powders utilizing a sodiothermic reduction from NbC15 - Al Cb dispersed into molten salts."

Jan 1, 2011

By Leszek Hoser

Polycrystalline oxide superconductors that have the perovskite structure, that are oxygen deficient, and that have compositions based. on the so-called. 1-2-3 (YBa2Cu3O7) compound, were investigated.. The materials exhibit a high critical transition to superconductivity at temperatures near 90oK. It was determined that maintaining the oxygen content within the correct range in connection with an appropriate amount of CU ions in the crystal lattice leads to high-critical temperature (Tc:) superconducting properties. High-Tc: superconductors with a critical temperature in the range of 100°K were developed. Further investigations, based. on the theoretical examinations of the origin of superconductivity, have been performed and are discussed..

Jan 1, 1989

By D. D. L. Chung

"In-situ network composites are composites in which the filler network is formed during composite fabrication, in contrast to ex-situ networks which are formed prior to composite fabrication. A homogeneous in-situ network composite has the entire network at the same composition; a heterogeneous in-situ network composite has different parts of the network at different compositions. The homogeneous network composite is made either by the Method of Molten Filler Flow or the Method of Dissolution and Deposition; a heterogeneous network composite is made by the Method of Liquid-Phase Networking. Examples include polymermatrix and metal-matrix composites.IntroductionNetwork composites refer to composites containing a continuous three-dimensional network as the filler. These composites are attractive in their lack of delamination failure, which is usually characterised by two-dimensional composites. The filler and matrix in a network composite can be considered two interpenetrating networks. The mechanical interlocking of the networks adds to the cohesion of the composite. In cases where the filer is much better than the matrix in a certain property, the network nature of the filler makes the filler highly effective in improving that property in the composite in all directions. The property desired in the composite may be high strength, high modulus, low coefficient of thermal expansion, high thermal conductivity, or low electrical resistivity."

Jan 1, 1994

By W. G. Davenport

Chapter 10 showed that any given smelting task, e.g. production of 65% Cu matte, 1500 K, from CuFeS2, can be done with many different combinations of: blast%02 hydrocarbon fuel blast temperature. This chapter repeats the Chapter 10 calculations but reports the results in terms of the mass industrial oxygen mass hydrocarbon fuel blast preheat energy combinations that will produce 65% Cu matte, 1500 K, from CuFeS2 concentrate. It also determines the energy inputs equivalent to these combinations.

Jan 1, 2001

By Lennart Hedlund

There is today a long and well-documented experience of the use of Boliden "Kaldo' technology for treatment of various feed matedals. The process is In commercial' operation in the Boliden Mineral's Rönnskär plant In Sweden for treatment of copper scraps and lead concentrates (In campaigns). This plant was built In 1976 for treatment of lead dusts from the copper plant but later modified to take other raw materials. Boliden's Kaldo techr:lology Is also In operation since 1991 for treatment of low-grade copper scraps In Enlrlsorse's plant In Porto Marghera (Venice), Italy. The plant is producing 25 000 tons of blister copper ,per year. The Kaldo furnace Isa high :Intensity smelting unit, where several successive treatment steps can be done In the same vessel. The furnace can be totally enclosed to protect the working environment, and the small off-gas volume can easily be dedusted. Input materials can vary over a very wide range, the products will be a dump slag with low (0,5%) copper and lead contents and black copper or blister copper. The dust from the process can be used for zinc production. A new development is autogenous smelting of scrap in a Pierce-Smith converter, implemented at Compagnie Générale d' Èlectrolyse du Palais in France.

Jan 1, 1995

By Federica Paglietti

In this work is presented SEX (Structural & Elemental X-Ray Instrument), the first spectrometer completely portable which make non-destructive X-ray fluorescence and diffraction analysis, in contemporary and in real time. This instrument has been realized using miniaturized detectors, the same model installed on the mission Pathfinder NASA, and X-ray microtubes. SEX allows the chemical and mineplogical characterization of all kind of solid materials and allows to make chemical stratigraphy and liquids analysis.

Jan 1, 1998

By E. Legault-Seguin

The current industrial practice in the processing of nickeliferous laterites involves the precipitation and releaching of Ni and Co to allow separation from the major impurities of Mn, Mg and Ca. A direct solvent extraction process has significant advantages over this practice, which suffers from difficult and costly precipitation steps, lower recovery and inherently complex flowsheets. The present investigation involves the examination of Cyanex 272, Cyanex 301 and Cyanex 302 as extractants for the direct extraction of Ni and Co from major impurities associated with laterite leaching, i.e. Mn, Mg and Ca. For Co extraction, Cyanex 301 and Cyanex 302 are superior to Cyanex 272, because they are able to selectively separate Co from Mn, Mg and Ca. Cyanex 272 offers complete extraction of Co from Ni and Ca, but Mn and Mg pose difficulty. Ni can only be extracted selectively with Cyanex 301, thus another extractant selective for Ni, such as Versatic 10 or Cyanex 301, is needed to recover Ni if Cyanex 302 or Cyanex 272 is used for the initial extraction.

Jan 1, 2004

By Dean David

The evaluation of a new mineral sands prospect with unusual characteristics is described, The heavy minerals are very fine grained, have comparatively low average specific gravity (3.6) and are altered. Poor performance by conventional processing techniques made it necessary to trace the response of the major minerals during the separation processes, QEM*SEM® was used to quantify mineral volumetric abundances and mineral locking in magnetic and gravity separation products.

Jan 1, 1989

By Issa S. AI-Kharusy

Oxidation/reduction (REDOX) alloy media, as used in wastewater treatment, is founded on the exchange of electrons. Because of this electron exchange, many contaminants are converted to harmless components which require no further treatment. Other types of contaminants are removed from the waste stream by electrochemically bonding to the alloy medium. This paper discusses the REDOX reactions, the role of the alloy medium in various treatment processes, and describes specific applications of REDOX alloy media for the removal and minimization of waste. The characteristics and handling of spent treatment media is also reviewed as a further consideration in waste minimization.

Jan 1, 1996

By Fernando Castro

Electric furnace steelmaking dust is a polluting residue that needs to be treated in order to recover metals contained and to produce an environmentally acceptable residue. Some hydrometallurgical approaches for its treatment have been evaluated, namely: caustic soda leaching followed by electrolytic recovery of zinc, ammonia leaching followed by zinc compounds precipitation and acetic acid leaching followed by lead, zinc hydroxide and gypsum precipitation.

Jan 1, 1992

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF's. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By J. Shibata

The recovery process of valuable metals, such as Ll, Mn, Ni and Cr from a waste lithium battery was developed n this study. Lithium and Mn are selectively leached from the battery by using dilute mineral acid. Main part of the battery comprises stainless steel, and Fe, Ni and Cr are easily leached by the mixture of dilute HCl and HNO3 Lithium and Mn are precipitated as metal carbonates from the? individual leached solution with sodium carbonate solution. The solution containing Fe,Ni and Cr Is treated by solvent extraction to separate NI and Cr from the leached solution. The experiments are carried out for leaching and separation steps. According to the experimental results, the flow. sheet for a recovery process of valuable metals from a waste lithium battery has been established.

Jan 1, 1995

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

The method of ultrasonic-assisted leaching was used to extract vanadium from the stone coal, with alkali as leaching reagent. The effects of ultrasonic power, concentration of alkali, reaction temperature, liquid-solid ratio and reaction time were investigated, respectively. The optimal ultrasonic leaching condition for vanadium extraction is as follows: ultrasonic power 230W, concentration of alkali 5%, liquid-solid ratio 3:1, reaction temperature 90℃ and reaction time 1h. The leaching rate of vanadium reaches 76.4% under the optimal condition, which is 12.2% higher than that of non-ultrasonic leaching. The reason on enhancing the leaching rate of vanadium by ultrasonic leaching was discussed. It is indicated that the ultrasonic cavitation can increase the surface area of mineral, which is beneficial to facilitate the reaction rate. Keywords: stone coal; vanadium; alkaline leaching; ultrasonic

Jan 1, 2014

By Huanyu Zhang, Quanqiang Ma, Huiqing Tang

Improvement of the coke quality for blast furnace (BF) iron making by hydrothermal oxidation treatment on coke quality was investigated. Results show that, under subcritical condition, sulfur removal rate is 15% and the weight loss is 3%; under supercritical condition, both sulfur removal rate and mass loss rate increase with the increase of H2O2 concentration. In the experimental conditions, sulfur removal rate and mass loss rates were 45% and 17%, respectively. Hydrothermal oxidation treatment could reduce the CO2 reactivity of the coke and the treatment under supercritical condition is more effective. Hydrothermal oxidation treatment could improve the graphitization of the coke and smoothness of pore boundary in the coke and the treatment under supercritical condition is more effective.

Jan 1, 2016

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifying its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multicomponent slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today's reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author's group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003

By Chr. Kersch

This project further develops supercritlcal fluid extraction as an industrial soil remediation process. Heavy metals are removed from sand using CO2, The effect of the type of complexing ligands, pressure and water content on the extraction efficiency is investigated.

Jan 1, 1999