Search Documents

By Mingsheng He, Yunhui Tang

The structure and granularity of biological origin aragonite from abalone shell during wet grinding in a ball mill were studied with X-ray diffractometer, with morphology studied by scanning electron microscope (SEM). It is shown from the results that the particle sizes of aragonite decreased with grinding time, so did the X-ray diffraction (XRD) peak intensities, while the full widths at half maximum increased. A calcite XRD peak with low intensity and great width was observed in nearly all the samples with various grinding time, whereas the intensity of the peak increased obviously after grinding time 300 min. It is shown from the SEM results that the size of aragonite dropped with grinding time until it reached 20 nm and then kept constant, while that of calcite dropped first and then rose at the minimum about 10 nm until to the constant size as in aragonite. It was observed that the mineral content obtained from XRD show an obviously change that the calcite increases while aragonite decreases, which indicated the occurring of a polymorphic transformation of aragonite into calcite.

Mar 1, 2017

By Anxiang Wang, Kunhua Wu, Yifu Li, Junjie Xu, Yongnian Dai, Bin Yang, Lingxin Kong

In this study, the saturated vapor pressures of tin (Sn) and antimony (Sb), the separation coefficient and the vapor-liquid phase equilibrium of Sn-Sb alloy were theoretically analyzed, which demonstrate that it is possible to separate Sn and Sb by vacuum distillation. The process parameters of vacuum distillation, including the distillation temperature, distillation time and alloy mass (thickness of raw materials) on the direct yield of Sn and the content of Sn in liquid phase were investigated by using single factor experiments. The preliminary results show that the direct yield and the content of Sn are 98.77 wt.% and 96.01% with the optimized distillation conditions of a distillation temperature of 1473 K, a distillation t ime for 45 min and a Sn-Sb alloy mass of 125 g ( thickness o f 8 mm). The distillation parameters in the study provide effective and convenient conditions on separation of Sn-Sb alloy.

Jan 1, 2016

By Liangying Wen, Xuewei Lv, Yuelin Qin, Feng Zhu, Guibao Qiu, Chenguang Bai, Meilong Hu, Shengfu Zhang

"The COREX process is the first reduction ironmaking technology with coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal and some coke. In order to increase the utilization of fine coal, reduce coke consumption and enhance the competitiveness of the technology, the combustion behavior of pulverized coal injection in melter gasifier is studied experimentally. The results show that the combustion rate of PCI increases with the increase of temperature. And the combustion rate increases with decreasing coal particle size. Compared bituminous coal with anthracite, the former’s burning ratio is higher than the latter in the same granularity. The combustion effect is remarkable when coal blend of bituminous coal and anthracite with the smaller particle size is pulverized in COREX process.IntroductionThe COREX process is the first reduction ironmaking technology with raw coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal [1-3]. However, the proportion of lump coal in raw coal is very small, and it is avoidless to produce fine coal because of mechanical coal cutter and storage and transportation process, so it is important to resolve utilization of fine coal in COREX ironmaking process in order to energy conservation and reduce the cost of hot metal [4]. Currently, Coal briquetting technology is adopted to utilization of fine coal in COREX process [5], but coal briquetting system has high investment cost and requires feasible adhesive agent. The pulverized coal injection (PCI) into a blast furnace is being used on a global scale to improve the stability and reduce the cost of blast furnace operations [6]. The successful development of PCI in blast furnace is contributed to pulverized coal in COREX melter gasifier. However, it is different in PCI process between COREX melter gasifier and blast furnace, and the differences are as follows: firstly, The air is injected into blast furnace, which temperature is about 1200 ?, but in COREX melter gasifier the normal temperature oxygen is blasted, so PCI in blast furnace begin burning in blowpipe, but the combustion of PCI in COREX melter gasifier is only in raceway. Secondly, the racway of COREX is smaller than that of blast furnace of the same size. So, the combustion behavior of PCI is complex in COREX melter gasifier, which is not use for reference."

Jan 1, 2012

By Bing Hu, Zhu-Cheng Huang, Guang-Bin Xia, Hu Peng, Hua Wang

"The temperature rising characteristics and reaction of the reduction of iron oxide pellets with anthracite fines were studied using a MW-L0316V microwave oven and Leica-DM-RXP polarizing microscope. The results show that iron oxide pellets and anthracite fines have good microwave absorbing properties, and high temperature and reducing atmosphere in a relatively short time for reduction of iron oxide pellets can be achieved. The reduction reaction, which follows the unreacted core model, is rapid and the metallization increases from 13.41% to 56.57% as the reduction end point temperature increases from 850oC to 950oC. The iron is formed, fine grain crystals of iron are transferred and the contraction of metal phase occurs firstly at the surface of pellets, which hinders the reduction reaction at the center of pellets. The rate of reduction reaction increases slowly as the reduction end point temperature increases from 950oC to 1050oC.IntroductionIron ore direct reduction can be divided into gas-based reduction and coal-based reduction. Owing to the effect of the resource and the related economic benefits [1, 2, 3, and 4], the development of gas-based direct reduction technology is restricted, but the development of coal-based direct reduction supported by the relevant industrial policy has very good prospects for application.As a source of clean energy, in China microwaves have been applied in many fields [5, 6, and 7]. Chen Jin studied the reduction of carbon pellets under microwaves, and has made some progress on reduction kinetics and reaction mechanisms. Other countries also have related research in this field [8 - 15], for example, Kotaro Ishizaki and Kazuhiro Nagata have done research on the reduction reaction of carbon magnetite heated by microwaves. The research shows that Fe3O4 is deoxidized to FeO at about 800oC, and FeO is deoxidized to Fe at 1000oC-1025oC. Due to the very good heat absorbing properties of iron oxide pellets and anthracite fines, the selective and rapid heating of microwaves can rapidly raise the temperature of pellets and anthracite, and the iron oxide pellets can be rapidly reduced. In order to provide enough theoretical basis for direct reduction by microwave heating, this paper studies the temperature rising characteristics, behavior of the reduction reaction and the changes of the iron oxide pellets and anthracite in the microwave field."

Jan 1, 2011

By Julyana G. Santana, Esperidiana A. B. Moura, Vijay K. Rangari, Olgun Güven, Angel Ortiz, Rene R. Oliveira

Ethylene-vinyl alcohol (EVOH) copolymers are widely used in the food packaging industry as gas barrier properties to oxygen, organic solvents, and food aromas. EVOH is very sensitive to moisture and its gas barrier ability deteriorates in high relative humidity conditions.This work aims to prepare flexible films based on melt-blending high density polyethylene (HDPE) and ethylene-vinyl alcohol (HDPE/EVOH/EVA blend) reinforced with graphene oxide (GO). The HDPE/ EVOH/EVA/GO flexible films were prepared by twin-screw extrusion and blown film extrusion processing. The flexible films samples were characterized by tensile tests, TG, DSC and FE-SEM analysis and the correlation between properties was discussed. In addition, the oxygen permeability tests were performed at 23 °C, 0 and 90% relative humidity using an OX-TRAN (MOCON Inc.).

Mar 1, 2017

By Alain Jardy, Thibaut Quatravaux, Denis Ablitzer

"A numerical model of the Vacuum Arc Remelting process has been developed and applied to simulate remelting of various metallic materials, such as specialty steels, titanium and zirconium alloys. In practice, electromagnetic stirring is sometimes used, resulting in a complex 3D molten metal flow. After having validated the numerical model for different remelting conditions, we can use it to study the effect of applying a constant or alternated magnetic field on the thermohydrodynamic behaviour of the melt pool. The intensity of flow turbulence, computed with a classical k-E model, is shown to depend strongly on the nature of electromagnetic stirring.IntroductionThe principle of the Vacuum Arc Remelting (VAR) process, illustrated in figure I, consists in melting a consumable metallic electrode of the required grade under a high vacuum, in order to obtain a sound ingot of good structural quality.During remelting, an electric arc is maintained between the tip of the electrode and the top of the secondary ingot, in order to ensure melting of the electrode. The metal droplets fall through the arc plasma and progressively buid up the ingot, which solidifies in contact with the walls of a water-cooled copper crucible. The secondary ingot formed in this way contains three distinct zones, corresponding to the liquid pool, fully solidified metal and intermediate mushy zone. In order to stabilize the arc, it can be confined with the aid of a magnetic field created by an external induction coil. This field can also be used to stir the liquid metal, the rotation induced being in the orthoradial direction. By reversing periodically the coil current, stirring can be alternated."

Jan 1, 2004

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By Xuemei Zheng, Aiyuan Ma, Jing Li, Jinhui Peng, Shaohua Yin, Libo Zhang

Zinc recovery from zinc oxide flue dust (ZOFD) by ultrasound enhanced neutral leaching process was investigated. In this study, the effects of leaching temperature, liquid/solid ratio, leaching time and ultrasound power were studied, and the conventional leaching experiments were also performed. The experimental results showed that the leaching time was greatly shortened and the leaching rate of zinc was effectively improved by the assistance of ultrasound. The optimum conditions of ultrasound-assisted leaching were determined as leaching time 20 min, temperature 35℃, and the liquid/solid ratio of 5. Under these conditions, the leaching rate of zinc was close to 80% as the ultrasound power of 540W, which was increased by 7% or so, in comparison with that of conventional leaching process.

Jan 1, 2015

By Ian Buterbaugh, Calvin Lo, Tomoko Sano, Brendan Koch, James Catalano, Timothy Walter

In this research, two grades of alumina, one at nominally 85% composition and the other at 99.5% were characterized. Microstructural and phase characterization was conducted using Scanning Electron Microscopy, Energy Dispersive Spectroscopy, X-ray Diffraction, and micro-computed X-ray tomography. It was determined that the Knoop hardness values were influenced by the porosity in the 85% composition. Quasi-static compressive tests and high strain rate compression experiments were conducted to determine the influence of the microstructure to the compressive properties. It was observed that the overall compressive strengths increased with strain rate. Although the Knoop hardness values were much lower in the 85% alumina due to the porosity, the compressive strength at both quasi-static and dynamic strain rates were not significantl lower than those of the 99.5% composition.

Mar 1, 2018

By Yu-ki Taninouchi, Toru H. Okabe

Among platinum group metals (PGMs), Pt, Pd, and Rh are the essential constituents of automotive catalysts. Recovery of PGMs from catalyst scrap is important, but it is difficult because PGMs are chemically stable and are present as minor components in the scrap. A vapor treatment method using FeCl2 vapor to alloy PGMs with iron, enabling subsequent magnetic separation, is developed and tested on Pt, Pd, and Rh wires.

Mar 1, 2017

By M. E. Myers

An experimental program is being carried out to determine the thermodynamic characteristics of zinc solubilization in high-temperature iron and iron-carbon alloys. Two versions of an isopiestic technique are being used, with zinc at a lower temperature being equilibrated with pure iron foils or molten iron-carbon alloys at a higher one. The lower temperature sets the partial pressure of zinc vapor, and thus the activity relative to a given reference state. Initial results show Henrian behavior for dilute zinc solutions in austenite and a molten 4.6% C alloy, with unit-pressure solubilities in pure Fe that closely match the predictions of Wriedt.

Jan 1, 1992

By Colin Dessemond

Since 1950, the traditional process has been dominating the production of lithium compounds from spodumene ores to sustain the lithium market because of its economic viability and the markets need for technical grade (99.5% purity) product. This traditional process includes thermal conversion, acid roasting and lithium leaching. However, this process has not been challenged and very few studies have tried to explain its limitation (95% lithium yield) or optimize the thermal treatment. Here, α to β spodumene conversion and lithium extraction were performed in a rotary kiln on a 2 mm to 2 cm spodumene concentrate instead of a micrometric one using a 1050 °C, 30 min conversion treatment and 250 °C, 30 min, 30% H2SO4 excess leaching treatment. X-Ray Diffraction analyses were performed on the converted material to determine the conversion rate by Rietveld analysis. It was observed after thermal treatment that the α-spodumene particles fractured and divided while the impurities remained compact. A sifting was performed after thermal treatment and it was determined that 65% of the initial mass became finer than 180 μm. X-Ray diffraction analyses and lithium content measurement were performed on both fractions and it was determined that the finer fraction had a very high lithium content of 3.24 wt%. Lithium extractions were performed on both fractions separately. While the coarser fraction’s lithium yield was only 61% the finer fraction’s lithium yield went up to 99% without any additional treatment. These observations may open more economical ways for the traditional process by potentially bypassing two third of costly steps such as grinding.

By Norihiro Murayama

The hydrothermal syntheses of zeolites from coal fly ash were carried out using NaOH and KOH as an alkali source. The cation exchange capacity (CEC) and the ion exchange selectivity were investigated for the zeolites synthesized by a hydrothermal treatment. The effective usage of the zeolite as a cation exchanger was considered from the viewpoint of engineering. Zeolite P, HS (hydroxysodalite) and K-CHA (potassium-chabazite) are mainly formed as zeolite species in NaOH or KOH solution at 393K. The zeolite P and K-CHA have a large exchange capacity as a cation exchanger. The cation exchange isotherms of various monovalent and divalent cations with various zeolites are investigated. The order of selectivity of the zeolites is as follows, NH4+> K+> Li+.For the divalent cation, the largest removal amount is obtained for Pb2+ in the low equilibrium concentrations below 0.2mmol/dm3, and almost perfect removal can be achieved for Pd2+. The order of selectivity of zeolites in low concentration is expressed in the following order; Pb2+> Co2+> Cd2+> Ca2+> Mg2+> Ni2+. Ii is considered the zeolites obtained from coal fly ash can be used as an excellent cation exchanger.

Jan 1, 2006

By A. Rikos, G. Pantazopoulos, A. Vazdirvanidis, A. Toulfatzis

In this study, the mechanical properties of an annealed CuZn36 rolled brass alloy with 0.2 mm thickness with respect to anisotropy expressed in terms of plastic strain ratio measurements (r-values, normal and planar anisotropy) are related with the development of specific rolling and recrystallization texture components obtained by EBSD. Anisotropic behaviour is primarily controlled by the crystallographic texture and constitutes an indicator of multi-axial mechanical behaviour, affecting directly the drawability and sheet metal formability. Microstructure examination employing optical and Scanning Electron Microscopy of tensile specimens are performed in order to investigate the emergent damage mechanisms in relation to the texture and structure evolution of the final product.

Mar 1, 2017

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Jie Qiu, Yun Chen, Kai Tang

The influence of SiO2 on the reducibility of the CaO–Fe2O3–SiO2 system was fully examined in this study. The isothermal reduction kinetics of CF and CF8S (CaO/Fe2O3 = 1:1, wt% (SiO2) = 8) were investigated through thermogravimetric analysis at 1123, 1173, and 1223 K with 30% CO and 70% N2 gas mixtures. The reduction of the samples with 8% SiO2 was not only highly accelerated but also proceeded easily. Rate analysis revealed that CF and CF8S reduction occurs in two stages, the Fe3O4-to-FeO stage overlaps with the previous Fe2O3-to-Fe3O4 stage and tends to approach the following FeO-to-Fe stage with the addition of SiO2. The apparent activation energy values of CF and CF8S reduction are 46.89 and 8.71 kJ mol−1. Sharp analysis indicated that CF and CF8S reduction was expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction.

Mar 1, 2017

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Iron precipitation occupies a vital position in the metallurgy industry, especially for treating iron-bearing sphalerite in hydrometallurgical processes. This paper emphasizes techniques for removing iron from high-iron sphalerite via hematite precipitation, and describes the results of research performed to examine ferrous oxydrolysis and precipitation. The behavior and mechanism of conversion between the iron phase and hematite residue at elevated temperature under pressure is ascertained by investigating the dissolving characteristic and thermodynamics stable area of hematite at sulfate system. The results show hematite precipitation went through the process of crystallization, dissolve, oxidation and precipitation of ferrous sulfate, and the overall iron precipitation was determined to be controlled by the rate of ferric sulphate hydrolysis rather than the oxidation of ferrous sulphate or the re-dissolution of ferrous sulphate crystals, or the transformation of basic ferric sulphate.

Mar 1, 2018

By J. E. Klein

Bench scale tests using a stack of ten whole SAES St909 pellets, 6 grams, to crack methane have been completed with pure methane feed. Test conditions ranged from 600 to 800°C at 101 kPa (760 ton) with a methane feed rate of ten sccm. Methane reformation tests, test where hydrogen was passed through a St909 bed after cracking methane, were performed to determine if and how much methane can be generated under "reformation" conditions. Phase structure determinations of St909, composed of a ZrMnFe alloy with aluminum used as a pellet binder, after methane cracking were complicated by the number of materials that can be formed by the elements in the St909 and the carbon from methane cracking. It was determined that the aluminum not only alloys with the Zr, Mn, and Fe in the St909 alloy, but also forms aluminum transition metal carbides in addition to ZrC as the carbon content and the temperature of the St909 increases. Some A14C3 was also found in some pellets. Passing hydrogen over St909 pellets after methane cracking formed methane at various rates in the temperature range of 600 to 800°C. Temperatures of 800°C gave the best methane cracking performance and efficiencies decreased rapidly with temperature.

Jan 1, 2002

By R. L. Miller

An industrial wastewater, including plating wastes, is treated with sodium sulfide and ferrous sulfate to form a sulfide-oxide precipitate containing chromium and other toxic metals. Hydrocarbons, in the water, coat the sulfide-oxide particles, impeding metal recovery. Froth flotation, without reagent addition, was found to recover 93.9% of the solids from the sludge with simultaneous rejection of 89% of the water. Methyl isobutyl carbinol (MIBC) improved recovery and potassium amyl xanthate improved both recovery and grade. The process design has wastewater feed (without MIBC) to the rougher circuit. The rougher concentrate is conditioned with MIBC and fed to a cleaner circuit to achieve a high grade concentrate. About 95% of the water is recirculated to the waste treatment plant.

Jan 1, 1992

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983