Search Documents

By N. El-Kaddah, A. D. Patel, T. T. Natarajan

The phenomenon of particle migration in a conducting fluid under an applied electromagnetic force field finds its application in selective sorting of minerals and more recently in the removal of inclusion from molten metal. This paper deals with the analysis of the expulsion force and the flow around a spherical particle in crossed uniform electric and magnetic fields in .infinite and in confined medium. Analytical solutions will be presented for the electrk and magnetic fields as well as the induced flow at the limit of zero Hartmann number. The flow around the particle was investigated numerically at low and high values of Hartmann number. It will be shown the magnetic field has almost no effect on the velocity field when Hartmann number is less than 1.0. At higher Hartmann numbers the damping effect of the magnetic field was pronounced in the direction of the applied current. It is concluded that Hartmann number has little effect on the net force on the sphere particle.

Jan 1, 1999

By K. Tozwa

The electrical conductivity of electrolytes for copper electrorefining and electrowinning processes has been reported by many researchers since 1911. The experimental results show that the conductivity increases with an increase in sulfuric acid concentration and decreascs with an increase in copper concentration. In pure copper sulfate solution, however, the conductivity increases with an increase in the copper concentration. After confirming the conductivity of pure and acidified copper sulfate solutions experimentally, the concentrations of hydrogen ion and free (not hydrated) water in the electrolytes were estimated and it was found that the relation between the conductivity of acidified copper sulfate electrolytes and the products of concentration of hydrogen ion and free water is linear. Accordingly, the conductivity of acidified copper sulfate electrolytes increases with an increase in sulfuric acid concentration and decreases with an increase in copper concentration.

Jan 1, 2003

By C. F. Feng, L. Froyen

"In-situ processes have emerged as new and promising techniques for metal matrix composite fabrication. They offer significant technical and economic advantages over conventional processing. One of the in-situ processing routes that have been used is reactive free sintering of a mixture of powder reactants. However, materials synthesised via this route are always porous because of density differences between reactants and products. An example are the porous Al/(TiB2+Ah03) MMCs obtained by heating powder mixtures of Al+ Ti02+B with Ti02 and B in stoichiometric ratios for forming TiB2• In this study, porous Al/(TiB2+Ah03) composites were further processed by hot-pressing at temperatures above 600°C. This processing cycle was designed so that the composites could be densified. Furthermore, the reaction kinetics of the in-situ processing are studied by means of DSC analysis measured at different heating rates. The activation energies of the three intermediate steps that are involved in the reactive processing for preparing AV(TiB2+Alz03) MMCs are determined to be 923 kJ/mole, 241 kJ/mole and 235 kJ/mole respectively.XRD proved that the hot-pressed products consist of Al, TiB2 and Al203- Properties of the products are assessed by microstructural characterisation (LOM, SEM and EDS), microhardness, Young's modulus and bending tests. The results show that good microstructures, elastic properties and strengths, as well as acceptable ductilities were achieved. For the composition 79.74wt% Al-15.95wt% Ti0z-4.31wt% B, after the reactive free-sintering and hot-pressing cycles, Young's modulus is 105 GPa, bending strength is 509 MPa and maximum strain is 5.0%; for composition 88.73wt% Al-8.87wt% Ti0z-2.40wt% B, they are 89 GPa, 311 MPa and 8.2% respectively. It can be seen that the properties of products can be tailored by adjusting the relative amounts of reactants in green samples. Furthermore, for comparison reasons, Al and a binary system Al-Ti02 were identically processed as the ternary systems. Their microstructures and properties were studied."

Jan 1, 1998

By Bin Zhu, Mingmei Zhu, Hong Zhou, Xiaofei Dou, Bin Xie, Yu Wang, Tiancheng Lin

In this study, the formation of 2CaO·SiO2 and 3CaO·P2O5 solid solution (nC2S-C3P) in hot metal dephosphorization process is discussed. The variations of CaO and SiO2 mass, both in nC2S-C3P solid solution phase and liquid slag phase with increasing P2O5 mass in CaO-SiO2-FetO-P2O5 slags were calculated using Factsage software. CaO-SiO2-FeOt-P2O5 slag containing up to 18 % P2O5 was melted at 1823 K then cooled to 1673 K. The contents of CaO and SiO2 both in the solid solution phase and liquid slag phase of quenched samples were observed and analyzed by SEM/EDS. Both the calculated and experimental results show that the contents of CaO and SiO2 in the solid solution phase decreased, just opposite in the liquid slag phase, with increasing P2O5 content in the slags. Formation mechanism of nC2S-C3P solid solution in the slags was derived based on the ionic structure theory of molten slag. The SiO4 4- in the nC2S-C3P solid solution can be replaced by PO4 3- in the liquid phase resulting in the increasing of free Ca2+ and SiO4 4- in liquid phase.

Jan 1, 2015

By Gökhan Demirci, Ishak Karakaya

"Energy consumption in electrolytic magnesium cells is well above the theoretical values. However, the mechanism of the back reaction, the main cause of the current losses, has not been fully understood yet. Magnesium dissolution into the melt is generally regarded as the limiting step for the back reaction. Accordingly, present cell designs are made with priority given to fast magnesium removal from the cell. However, experimental data and modeling results in this study indicate that the limiting step for the back reaction between magnesium and chlorine is the chlorine dissolution into the electrolyte when physical contact between electrolysis products was eliminated. Effects of chlorine bubbles on the current efficiency and the cell potential were investigated. Results show that the extent of back reaction is proportional to the chlorine surface area in contact with the electrolyte per unit time, and the cell potential increases with the amount of chlorine bubbles inside the electrolyte.1. IntroductionMagnesium is less dense than the electrolyte in electrolytic magnesium production. Therefore, both electrode products, magnesium and the chlorine gas, move upwards inside the molten salt electrolyte during electrolysis. The upward motion of electrode products promotes the most important current loss mechanism, the ""back reaction"". Separation of the highly reactive species; liquid magnesium and the chlorine gas in the cell, to prevent their recombination is one of the main concerns in cell designs. The employment of large inter-electrode distance or a separation wall in early cell designs; decreased the extent of recombination, but increased the cell voltage and energy consumption. Recent cell designs, on the other hand, make use of lifting action of chlorine gas [1,2] by utilizing smaller inter electrode distances to separate the magnesium and chlorine gas faster. Although energy consumption was reduced, but more physical interactions between electrode products make electrolytic magnesium cells still highly inefficient when energy consumptions are compared with the theoretical values. Today, the most efficient industrial cells utilizing high purity feed operate at 10.5-11.5 kWh kg-1 Mg [3-5] and it is considerably higher than the theoretically attainable value of about 6.0 kWh kg-1 [6]. This large gap demonstrates the necessity of more research on physics and chemistry of magnesium cell electrolysis."

Jan 1, 2011

By Suzzann Nordwick

The metallurgical treatment of mercury-containing materials for precious or base metals recovery imposes many processing and environmental challenges. Mercury is usually present as elemental or cinnabar. Historically, mercury has been removed from mined ores pyrometallurgically by roasting, but hydrometallurgical methods have also been employed. For example, alkaline sodium sulfide solution acts as an universal solvent for most mercury compounds. While, most other metals are highly insoluble in this solution. This allows for a high degree of selective separation of mercury from other metals with the exception of tin, antimony and arsenic. Mercury leached with a solution of sodium hydroxide and sodium sulfide or sulfur can be re-covered by cementation or stabilized through sulfide precipitation. Hydrometallurgical technology for the pretreatment of mercury removal from gold, silver, and base metal ores using alkaline sulfide leaching will be discussed with a focus on alkaline sulfide leaching of mercury sulfide-containing materials.

Jan 1, 2003

By Robert M. Leary

The Kennecott Utah Copper smelter operates two Outokumpu flash furnaces: a smelting furnace for production of high-grade matte and a converting furnace for production of blister copper. Flash furnaces typically possess several characteristic features that must be considered in process control development such as long lag times associated with settler volume, non-linear input and output responses, large process gains, and unmeasured disturbances. Additionally, the Kennecott smelter possesses certain unique characteristics which must be considered such as single mine concentrate source, limited concentrate blending capacity, and feed preparation facilities that inevitably cause significant lags between furnace control parameters and manipulated set points. In order to improve furnace control and on-line time, a process control system was developed to address these issues. The feed forward control module provides predictive control and operates in response to furnace feed input changes. The feed back control module provides responsive control and is based on furnace output deviations. To provide regular feed back information to the control room supervisors, new sampling methods were developed which provide the operators with molten metal and bulk material samples at regular intervals to provide information for control. The control system was implemented on the Flash Converting Furnace in May 1999 and on the Flash Smelting Furnace in August 1999.

Jan 1, 2000

By R. Hurman Eric

The electrode in a slag-resistance electric furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power, i.e. heat needed for the operation. The control parameters are the size and positioning in the slag bath which are defined by slag resistivity, furnace resistance, cell constant and power input sequence all of which are closely interrelated. The flow of heat generated by the electrode current determines the energy distributions and thus the furnace dimensions. Heat flow models concerning vertical, horizontal and combined two-dimensional flows are discussed. All these considerations are based on the experimentally determined slag properties such as its resistivity.

Jan 1, 1995

By I. D. Reznik

Results of thermodynamic computations have been presented for reactions occurring in the process of segregation roasting of oxide nickel ores to describe more accurately the mechanism of the process. Under conditions of laboratory-scale roasting in combination with close-circuit flotation flow-sheets and magnetic separation, a recovery of 80-82% of nickel into 8 to 10% Ni concentrate and a recovery of up to 66% of cobalt was achieved. Process conditions have been selected for processing of both high-iron and high-magnesium ores. The feasibility of conversion of 94-98% of nickel and cobalt into solution by oxidizing pressure leaching with sulfuric acid has been demonstrated. It has been substantiated that it is reasonable to introduce double-stage segregation roasting.

Jan 1, 2003

By K. V. Sreenivas Rao

Solidification experiments have been conducted to study the effect of interface heat flux and air gap formation on cooling rate of the casting during solidification of Al-4.5wt%Cu alloy. The thermal history of the casting and mold during solidification is recorded using thermocouples connected to computer interfaced data logger. The measured temperatures in the mold are used as input to the IHCP (inverse heat conduction problem) algorithm for simulating multiple heat flux components at the boundary. It is observed that the filling effects induce spatial variation in the thermal field in the mold and casting regions and greatly influence the cooling rate of the casting. The study demonstrates the use of IHCP and in-situ measured thermal profile in analyzing the cooling rate and microstructure.

Jan 1, 2008

By Masayuki Kudoh, Kiyotaka Matsuura

"Molten aluminum and nickel cast onto a steel block exothermically react and produce molten nickel monoaluminide, NiAI, which is simultaneously joined to the steel. The heat of the exothermic reaction is transferred to the steel block, and steel near the surface of the block is melted. The depth of the melted steel increases with both the initial temperature of the steel block and the thickness of the produced NiAI. Iron from the melted steel dissolves in the molten NiAI, and an intermetallic compound of NiAI-Fe pseudo-binary system is produced. During solidification of the intermetallic compound, it is strongly joined to the steel. The Ni.Al-Fe intermetallic compound has an excellent resistance to oxidation and corrosion.IntroductionAn intermetallic compound of nickel monoaluminide, NiAl, offers many advantages over conventional superalloys, such as higher melting temperature, lower density, greater specific modulus and higher thermal conductivity [1]. NiAl also exhibits excellent high-temperature oxidation resistance when doped with zirconium or hafnium, and excellent high-temperature corrosion resistance when doped with chromium or yttrium, that are superior to existing high temperature alloys or coating materials [1-4]. On the other hand, NiAI is significantly brittle at temperatures below 600 K [5-7], which is the most sigriificant disadvantage of NiAI. A possible way to overcome the disadvantage and to utilize NiAl as an environmental-resisting high-temperature structural material may be joining of NiAl to a ductile material."

Jan 1, 2000

By Mark Jolly

"Over the last ten years or so many man hours have been dedicated to developing methods for simulating shape casting processes. The majority of the methods developed have been devised by a combination of computer, mathematics and materials specialists often with limited knowledge of foundries and foundrymen. As a result of this it would appear that although there are many software packages for the foundryman to use there still exist fundamental misunderstandings as to their usefulness and suitability within the foundry.The paper aims to identify how well current software packages perform. The relationships between physical phenomena, practical defects and software capabilities are presented. Some discussion of the use of criteria functions is also presented. Finally issues arising from the postprocessing of results are discussed as the presentation of the results to the lay-person in simulation techniques is possibly one of the most important aspects in influencing the adoption of this type of software in the foundry community."

Jan 1, 1999

The Kaldo furnace smelting technique was developed for oxygen steel production by the late Prof. Bo Kalling, Domnarvet, Sweden. Development started in 1948, and production in 1956. Five million tons of steel were produced in TBRC's in 1973. Mainly due to high TBRC maintenance costs, the steel industry now prefers non-rotating converters. In non-ferrous metallurgy, however, qualified new applications of the TBRC technique have been realized or are being considered. Inco, Canada, succeeded to convert nickel matte to metal in the Domnarvet pilot plant in 1959, and have now installed a commercial plant in Copper Cliff. La Metallo-Chimique, Belgium, has pioneered secondary copper smelting and refining in the TBRC, operating plants in Beerse, since 1968, and Alton, U.S.A. Peko-Wallsend Ltd., Tennant Creek, Australia, was faced with the problem of producing saleable blister from concentrates containing 1.5-2.0% Bi. The flash smelting matte, containing 0.2% Bi, could not be refined to an acceptable limit of 0.03% Bi in the blister copper in a Peirce-Smith converter. Tests at Domnarvet indicated that a TBRC would achieve satisfactory bismuth elimina- tion. Two TBRC's were installed in Tennant Creek and operated for 14 months during 1974-75. The problems encountered and how they were over- come are described. Further TBRC applications have been studied in Sweden.

Jan 1, 1976

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983

By Adam C. Powell

A new Cahn-Hilliard phase field model of transport-limited electrochemistry describes phase boundary motion due to oxidation and reduction reactions at metal-electrolyte interfaces. Benchmarks demonstrating the accuracy of the method include open circuit voltage and closed circuit current in metallothermic reduction, and linear stability theory in metal electrolysis, including a new stability criterion for reduction of liquid metal from liquid electrolyte. The model is applied here to understanding cathode interface stability in titanium electrolysis e.g. in the SOM process developed with Uday Pal, and to structure evolution in subhalide reduction of titanium dichloride by magnesium developed by Toru Okabe. Potential for application to new fuel cell and battery systems is also discussed.

Jan 1, 2006

By D. Doungdeethaveeratana

The extraction kinetics in a novel solvent extraction process have been investigated. In this process, the liquid-liquid emulsion is generated by bottom gas injection into countercurrently flowing aqueous and organic phases. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration, without any mechanical moving parts, and the ease of cleaning and process control, while providing a sufficiently large interfacial area for rapid mass transfer. The overall rate increased with increasing gas injection rate and height of the aqueous phase but decreased with increasing injector diameter at the same gas injection rate. The variation of the overall rate constant was correlated against a set of dimensionless numbers, representing the operating conditions. Extraction rates and efficiencies comparable to those in a mechanically generated emulsion were attained in this new process.

Jan 1, 1998

By Timothy W. Ellis

"This paper presents the basic theory of operation, physical chemistry and phase equilibria which allow the development of liquid-liquid extraction circuits based on metallic solvents. The incorporation of reduction and reduction/diffusion processes into the process scheme is discussed and a detailed description of several liquid-liquid extraction schemes are developed. A synopsis of experimental results obtained using this method to separate rare earth and other metal based materials will be given.IntroductionConcerns over the effects of waste materials in the environment has been one of the significant social hallmarks of the late 20th century. Essentially every industrialized country has had to incorporate the cost of waste material into the equation of production. Legislative initiatives have led to the passing of very tough laws, by historical standards, which govern the environmental impact of materials processing.Liquid-Liquid extraction is a very common unit operation normally using aqueous and/or organic based solvents. Early work at the Ames Laboratory focused on the use of this technique for the reprocessing of spent fuel from liquid metal breeder reactors by the use of metallic solvents. Recently, we have revisited this area as a means to recycle/reprocess several emerging rare earth based materials, although this method has a much wider range of application. The reinvestigation of this technology is particularly timely as hydrometallurgical based processes are coming under increasing scrutiny in the U.S.A. by the Environmental Protection Agency (EPA). Although technology currently exists to remove contaminants from aqueous based waste streams, often the application of such methods is expensive. With proper design and judicious selection of reagents liquid metal extraction can achieve a high recovery along with a benign waste stream.This process has several possible advantages over other technologies. First is the elimination of aqueous solvents. Therefore, problems associated with disposal or reprocessing of the aqueous carrier are eliminated. Second, with proper system design, very high separation coefficients can be obtained thus limiting the number of stages required. Third, metals are extracted from metals with a metallic product, thereby eliminating the need to re-reduce metal for oxides or other compounds which are the common output for aqueous based extraction procedures."

Jan 1, 1996

By Dian Adisty, Leiv Kolbeinsen, Eli Ringdalen

In Si and FeSi production, the main Si source is SiO2, in the form of quartz. Reactions with SiO2 generate SiO-gas that further reacts with SiC to Si. During heating, quartz will transform to other SiO2 modifications with cristobalite as the stable high temperature phase. Transformation to cristobalite has been investigated and shown to be a slow process where the rate varies between the investigated quartz types. The effect of quartz versus cristobalite as SiO2 source has been studied for reaction (1) 2SiO2 + SiC = 3SiO + CO, by heating of pellets with SiO2 + SiC in Ar-gas. The reaction was faster with cristobalite than with quartz. Initial experiments indicates that this is the case only in Ar and not in CO-atmosphere The higher specific surface area of cristobalite is believed to contribute to the higher rate. The industrial consequences of the observed difference between quartz types are discussed.

Jan 1, 2014

By Nobuhiro Oguma, Yuji Mizuta, Hideya Sato, Shigehiko Iwahori

"Recyclable materials containing copper and precious metals have been treated at the Mitsubishi Process in Naoshima. In 2003, a new incinerating and melting plant (pre-treatment plant) for waste materials, such as shredder residue of automobile and scrapped appliance, was constructed. All of produced slag/metal mixture is treated at the Mitsubishi Process, and which results in the significant increase of recyclable materials treatment. The combination of two processes has realized a highly efficient and environmentally friendly system for recycling valuable metals in the waste which used to be sent to a landfill. Naoshima continues to make efforts to achieve the highly efficient operations of the two processes, and plans to increase the treatment of recyclable materials further. This paper summarizes the recent operations and the various improvements implemented in the pre-treatment plant.IntroductionRecyclable materials containing valuable metals such as copper and precious metals have been treated at the Mitsubishi Continuous Copper Smelting and Converting Process (Mitsubishi Process) since the start-up in 1991. In the early stages, recyclable materials consisting mainly of metal scrap were charged into the process and the treatment had been increased steadily. In order to promote the recycling business, treatment of various kinds of materials including printed circuit boards was started. However, the treatment hit the ceiling due to a limitation of furnace boiler capacity, since they contained large amounts of combustible materials. In addition, severe corrosion of boiler tubes was caused by halogen contained in recyclable materials."

Jan 1, 2012