Search Documents

By Gabriel Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

Jan 1, 2007

By D. Su

This paper presents the details and results of a preliminary investigation into the response of borehole pressure cells (BPCs) in soft coal. Two parallel approaches, laboratory calibration and nonlinear finite element simulation, were adopted for deter- mining the BPC K-factor, which was defined as the ratio of cell pressure change to the corresponding change in external pressure. Results from both the laboratory calibration and the nonlinear finite element simulation revealed a nonlinear response of cell internal fluid pressure to external loading. The K-fact& also is shown to increase with increasing setting pressure and decreasing medium modulus. -Depending on the setting pressure, the K-factor for coal having a Young's modulus of 1.6 x lo5 psi ranges from nearly 1.2 at 2,000 psi of external pressure to 1.485 at 8,400 psi of external pressure. The improved under- standing of BPC behavior leads to the more accurate calculation of BPC K-factor in coal which significantly improves the correlation between pillar pressures measured in underground coal mines and those predicted by nonlinear finite element simulations of these pillars.

Jan 1, 1990

By Navid Hosseini

Several empirical equations to estimate coal pillar strength have been presented in academic studies. The development processes of these equations are similar and are usually obtained by fitting the mathematical function (curve) to field data. One of the best criteria to evaluate the quality of fitting for such equations is the correlation coefficient R2, which has limited applicability. It is necessary to calculate the correlation coefficient access to the initial data for which the equation is presented; this is impossible for many coal pillar strength formulas. This paper presents a new approach based on the analysis of uncertainty amplitude to compare the coal pillar strength. This approach utilizes a combination of parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), function type and degrees of freedom. The confidence level of constants is subsequently formed and the correlation coefficient becomes more comprehensive. Therefore, for an effective comparison, the efficiency and accuracy of coal pillar strength formula can be used. Keywords: Coal Pillar Strength, Correlation Coefficient, MATLAB, Uncertainty Criterion

Jan 1, 2012

By Bill Kyslinger

In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Boart Longyear Poland and KGHM, J. H. Fletcher & Company was tasked to design and manufacture a single-boom, single operator drill module for installation of 1.2 meter expansion bolt in a 1.6 meter height mine. The objective was to produce a machine to provide ergonomic improvements for the operator while working in the mine environment. This dictated the requirement for a small easily controlled, maintenance friendly design with a remote operator?s control station. The selected design method was to use starter and finisher drill steels. This combination, requiring a number of mechanized machine motions, provides the ability to drill the required depth in the specified mine height. To accomplish the task from a remote location, a conscious decision was made to employ current technology in the form of small pressure compensated hydraulics and electronic controls. The result of the design method is a modular assembly with each sub-component designed to be replaceable and adjustable independently from other machine components. The low profile remote roof bolting module is made up of six major sub-components. Each major component is painted a different color to help the operator make the visual connection from the drill module to the operator?s control/display monitor. The Stabilizer (White) secures the module between the mine top and floor. The Drillhead (Orange) produces the drilling rotation and torque but also must slide out of position to allow the machine to manipulate the drill consumables. The Drill Steel Carousel (Blue) holds and indexes the starter and finisher steel from position to position. The Manipulator Arm (Green) moves and guides the drill steels and drill consumables from position to position during installation. The Roof Reference Guide (Yellow) locates the mine roof and guides the drill steels and drill consumables into position. The Linear Bolt Carousel (Purple) holds the drill consumables. The low profile remote roof bolting module allows the operator to drill and install a roof bolt manually or automatically with the push of a button. This design substantially reduces the operator?s exposure in the mine environment, as well as inherent pinch points and rotary hazards. Positioning the operator safely in the confines of the air conditioned cab.

Jan 1, 2006

By Krzysztof Kotwica

The steady demand for rock materials leads not only to on increase in mining but to the need for decreasing the loss of material in the process of exploitation as well. It brings about an increase in using of explosives in open pits and as a result an increase of after blasting gases volume, vibrations, the scattering (dispersion) of stone ect. All these factors affecting the environment lead to the research work for applying the electrohydrodynamic methods both in open casts and underground mines. In the article the authors describe the concept of this method and construction of equipment which recently have been successfully introduced in mining, the results obtained determine the possibilities of using this method and the future directions. The results of combined method with high-pressure water jets cutting and prototype equipment for separating rock blocks from the rock mass using special head with high-pressure water jets are also described.

Jan 1, 2006

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008

By B Whittaker

The paper examines the role of chain pillars in longwall mining layouts as used in several countries. The application of chain pillars in relation to their expected design role is discussed. An important feature is the specification of the pillar design to meet strata loading conditions as imposed by the mining and geological setting. The paper relates longwall width and chain pillar configurations to pillar size to satisfy anticipated loading and strength expectations. Laboratory work is referred to which examines criteria for pillar stability. Comments are made regarding the application of the findings presented in the paper, to different situations involving the use of chain pillars in longwall and shortwall mining systems.

Jan 1, 1987

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories and other ground control subjects and broad experience are required.

Jan 1, 2009

By James Pile

Long, high capacity, highly tensioned, cable bolts (strand bolts), stiff enough to be installed with resin like a solid bolt, yet flexible enough to be used in any lengths, have been widely used in Australian coal mines since the early 1990?s. A brief history and update on recent developments of this technology is provided. The first major US trial of this Australian technology, has recently taken place at BHP Billiton?s San Juan longwall coal mine in New Mexico. Thirty-five foot long, high capacity, highly tensioned, post-grouted cable bolts are being used to provide active secondary support of intersections in areas where operator safety and life of mine considerations are paramount, and standing support cannot be installed for reasons of equipment access. The cable bolts are resin anchored into overlying sandstone channels, tensioned, and post-grouted. The installation procedure and support results for these highly tensioned cable bolts are given.

Jan 1, 2007

By Craig Compton

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers? compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

Jan 1, 2007

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Sandin E. Phillipson

The Mine Safety and Health Administration?s Roof Control Division responded to a massive ground failure at an underground marble mine in northern Georgia. The ground failure occurred in a benched area that had been abandoned in the early 1990s. It involved the failure of an estimated 19 pillars, in conjunction with a massive roof fall of an undetermined extent that was at least 60 ft high. Pillars in the benched area had been mined nominally 40 x 40 feet to a height of 50 feet ft, with 40-ft mining widths, although it seems likely from measurements and accounts from mining personnel that pillars were even smaller than intended. Average overburden depth was 500 ft, and the rock mass was characterized by three sets of intersecting geological discontinuities that not only defined very blocky conditions that were conducive to pillar spalling and volume loss, but they were also adversely oriented in such a way as to cut diagonally through pillars at a high angle. The recently released S-Pillar software from NIOSH was used to determine pillar safety factors in the failure area and indicated that pillars were undersized for the conditions. S-Pillar was used to assess pillar stability in active areas to evaluate the likelihood of experiencing similar collapses in the future. S-Pillar correctly identified the pillars in the bench area as having been at risk for instability, in light of their ultimate failure. A two-dimensional finite element model was used to evaluate the possible stages of failure and to assess the likelihood of continued failure in the benched area that might affect more distal mine openings. Although stone mines are generally characterized as having more forgiving conditions than those found in softer sedimentary rocks, the failure shares some characteristics with domino-style massive pillar collapses experienced in coal and trona mines. First, the minimum dimension of the benched area approached 350 ft; second, the pillars defined by benching had small width-to-height ratios (0.8), and; third, the pillar failure area was slightly greater than 4 acres. The massive pillar collapse and associated roof fall illustrate the importance of incorporating pillars that have been properly sized for depth and for the final bench height. Furthermore, the designed dimensions must be adhered to during the actual mining process. Finally, the importance of understanding the geological conditions and their effect on the rock mass is critical.

Jan 1, 2012

By Alan A. Campoli

The mining industry has long been searching for an effective structural application that prevents weathering and falls of loose rock, debris, and sediment. J-Crete is a fiber-reinforced, engineered, cementitious composite rock application that is designed, tested, and successfully utilized as such a material. Laboratory evaluation of J-Crete material properties has shown the final compressive strength to be in excess of 7,300 psi (50.34 MPa), with 24 hour strength in excess of 1,500 psi (10.34 MPa). The flexural tensile strength is in excess of 600 psi (4.1 MPa) and is provided through a unique combination of polyvinyl alcohol (PVA) fibers activated by a proprietary liquid additive that prevents them from clumping and enables even distribution throughout the grout. Tensile bond strength in excess of 350 psi (2.4 MPa) at 28 day cure tightens the strata and holds loose material in place. Practically impervious to gas and liquids, J-Crete protects strata against long-term weathering, does not require screening to be effective, and has proven to be a successful waterproofing material. J-Crete has demonstrated the potential to alleviate coal mine roof cutters in soft, wet clay formations. J-Crete reinforces coal mine ribs by bonding directly to the rib, conforms to the strata, strengthens the rib, and eliminates sloughing due to long-term weathering; stabilizes coal mine entries by bonding directly to the brow and roof, and creates a monolithic shell with double reinforced corners.

Jan 1, 2012

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By Alexander Garcia

Roof and rib falls are the basic ground control hazards associated with underground roadways during development, stand up and, if applicable, retreat. Falls of ground can happen following the deterioration of supports or rock conditions over time, and particularly as a consequence of continuing rock deformation and/ or failure to install adequate support. Once developed, the risk of a failure is increased due to the effects of time as well as to front abutment stresses through retreat mining. The measurement of strata displacement using monitoring equipment is a form of ground control risk assessment. These monitoring systems are active, or ?live?, in a sense that risk is assessed real-time. However, there are circumstances in which falls of ground can occur without the prior recording of excessive movement. In addition, monitoring equipment is typically placed at set intervals, and strata conditions could vary between these points. Consequently, a visual assessment of other factors contributing to the risk of a fall should be made in order to complete a ground control risk assessment. Such surveys are usually one-off, thus capturing roadway conditions at one particular point in time. Ongoing deterioration is not documented through such one-time surveys, and there is a requirement for real-time or live assessment where a system is in place so that observation data can be updated on an ongoing basis, and a useful summary of prevailing roadway states produced on demand. To address the shortfalls of one-time assessments, a ?live? computerbased quantitative ground control risk assessment process has been developed. It combines visual observations processed in a quantitative manner with existing monitoring data into an interpretable output which indicates zones of roadway where there is an increased risk of a fall of ground from the roof or sides, so that remedial action can be carried out to mitigate that risk. Through improved procedures, it is now possible to generate a ground control risk assessment for each roadway, and one which can be updated frequently. This paper aims to outline and describe the assessment process.

Jan 1, 2012

By Kazem Oraee

Falls of ground have historically been the main cause for fatalities in underground mines. Although recent advances in technology have reduced the number of such accidents, when failures occur they usually result in severe consequences. Risks of rock falls, use of heavy machinery and electrical apparatus, entry to confined spaces, working in noisy and dusty environments, and working on unstable platforms are some of the hazards in ground control operations. Managing these risks requires a management regime involving strict adherence to operational codes of practice and an enshrined culture of safety. These should be subsequently reinforced through active participation of management, systematic training, and stringent internal and third party auditing. Accident reports show that the major contributing factor in most rock fall accidents is the failure to adequately manage known risks due to the lack of a systematic process. OHSAS 18001 (Occupational Health and Safety Assessment Series) is an international occupational health and safety management standard specification to develop occupational health and safety at the workplace. This standard is intended to help mine operators control occupational health and safety risks. Addressing the requirements of OHSAS 18001 can be a complex and demanding task. A comprehensive guide for efficient and accurate implementation of this standard is provided in this paper. The discipline can be used to establish an accountable management system foreground control activities in underground coal mines. The paper also provides guidelines for preparing necessary documents, devising safety policies, procedures, performing risk assessment, and handling instructions. Finally, the paper concludes by providing a sound analytical basis in terms of the creation of a robust safety management system foreground control operations in underground mines. Full benefits of implementing an effective and systematic operational health and safety management system are illustrated. The procedure adopted and prescribed in this paper can be used in all underground coal mines where lack of appropriate ground control practices can create deficiencies in both safety and productivity.

Jan 1, 2012

By Tara Bajpayee

Modern, highly productive underground mining operations need to assure the safety of their workforce by understanding where major strata fractures and roof failures could occur. Mines depend on a host of tools to assess ground instability. In-mine microseismic monitoring systems with sufficient number of sensors have also been used to provide this information. These in-mine systems must be robust in design and moved regularly to keep up with the mining advancement. System performance issues depend on maintaining ever increasing cable runs, preventing component damage from mining activities (scaling, blasting, etc.) and avoiding signal degradation due to interference from mining equipment (fans, trucks, electrical equipment, etc.). A potential solution is to use a surface based monitoring system having sensors placed in boreholes above and adjacent to the underground mine workings. These sensors must be capable of detecting and locating strata fracturing associated with rock failure events. A great advantage of a surface based monitoring system is its independence from the underground mine infrastructure. There is less concern with cable maintenance problems, signal degradation by interference from mining activity, or loss of power from the mine?s power grid. The disadvantages include the cost of drilling boreholes and challenges associated with placing sensors in the boreholes, maintaining radio communication and solar power, and public interference (vandalism, etc.). This paper describes a case study where a surface based microseismic system, using triaxial geophones in boreholes drilled from the surface, was deployed at a large limestone mine. The system was operational during a roof fall that occurred in October 2007. It detected the first rock fracture event 17 minutes before the rock fall event. The geophone array was sensitive enough to identify all large rock fracture, impact, and blast events as well as medium size rock fracture events occurring close to the geophone array.

Jan 1, 2008

By Andre Zingano

The objective of this paper is to compare the behaviors of different types of roof bolts: (1) One-Step Bolt (OSB), (2) Fully grouted Bolt (RB), (3) Combination Bolt (CB), and (4) Torque tension Bolt (TB). Two dimensional numerical models were built for both bolted and unbolted roofs. The geological sequence and rock properties used in the numerical models represent the typical roof condition for Pittsburgh coal seam. Using the unbolted roof as a base case, a comparison is conducted by monitoring the roof vertical displacement at the center of the entry and at the bolt positions, the axial force in the roof bolts, and stress distribution in the bolted area. The grout/rock interface is assumed to be perfect. The estimated roof displacements showed that the differences among the four types of roof bolts are small. The major differences are in the shear stress at the grout/rock contact and in the shear stress along the immediate roof bedding interface as well as in the bolt axial stress. There is less axial stress for the OSB compared to RB and CB as the diameter of the OSB is much bigger and the contact area between grout and rock is twice as large as for RB and CB. The higher strength of the OSB contributes to keep the bedding planes in the roof closed.

Jan 1, 2007