Search Documents

By M. Botz

Anatolia Minerals Development Limited (AMDL) is constructing the Çöpler Gold Project in eastern Turkey and commenced mining in the fourth quarter of 2009 with gold production scheduled to begin in the fourth quarter of 2010. The project is a 15,500 tonnes/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life approximately 40 million tones of ore will be placed on the leach pad, which will contain about 35,000 tonnes of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the mine life. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

The molecular structures of isobutyl xanthate (IBX), diisobutyl dithiophosphate (DIBDTP), O-isobutyl-N-ethyl thionocarbamate (IBETC), O-isobutyl-N-ethylcarbonyl thionocarbamate (IBECTC) and O-isobutyl-N-ethylcarbonyl thiourea (IBECTU) were fully optimized using density functional theory (DFT) at the B3LYP/6-31+G(d,p) level with the integral equation formalism for the polarizable continuum model (IEF-PCM) in the aqueous phases. The effects of the polar groups in these thiol molecules on their collecting performances were determined by the energies and compositions of frontier molecular orbitals and the atomic charge values. Our results indicate that the sulfur atom(s) in IBX, DIBDTP, IBETC, IBECTC, or IBECTU molecule is the centre of reactivity. And the collecting abilities of these reagents for copper sulfide minerals follow the order as: IBX > IBECTU ? DIBDTP ? IBECTC > IBETC, and the order of their selectivities against pyrite is suggested as: IBX < DIBDTP < IBETC < IBECTU < IBECTC. The theoretical analysis provides an insight into the collecting powers of these collectors, and offers an atomic scale approach to understand the experimental data available in the literature. Keywords:xanthate; dithiophosphinate; thionocarbamate; thiourea; density functional theory; structure-activity relationship; copper sulfide mineral

Feb 27, 2013

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, NV began large-scale production in 1977. During 2008 Round Mountain Gold Corp. (RMGC) relocated the primary crusher facility approximately 300 m (1,000 ft) to make room for the next phase of openpit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket. RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17-m- (56-ft-) high mechanically-stabilized embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, CO. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design and construction of the MSE wall.

Jan 1, 2010

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By C. Asgaard

Asset availability has been a longstanding objective in mining and mineral processing plants around the world. Enormous resources in both dollars and manpower are invested in improvement efforts to achieve higher asset availability. One dimension of asset availability is the time equipment is out of service for large scale planned maintenance activity: grinding mills, kilns, furnaces, mobile equipment, shovels and draglines are all regularly taken out of service for extended repairs and service. The speed, cost and quality of these planned outages provide an opportunity to increase asset availability. Equipment shutdowns are projects that are executed in a compressed time period. This paper will describe how the overall time and cost of equipment shutdowns were significantly reduced at Cliffs Natural Resources Michigan Operations (CNRMO) through the introduction of the Critical Chain Project Management techniques.

Jan 1, 2009

By S. Hamilton

Borates are essential to life, and to many products that are essential to an acceptable standard of living. They occur naturally in seawater at an average concentration of five milligrams of boron per liter. Fresh water lakes, rivers, streams and ground water generally have concentrations of about one milligram boron per liter. Borates are also present in soil at concentrations ranging from 0.1 to three milligrams of boron per kilogram. Because most of that boron is locked into insoluble minerals, clay or organic matter, boron deficiency is more widespread than boron enrichment. Borates evaporate into the atmosphere from seawater, rain, snow and hot springs. In rain and snow, natural boron concentrations range from 0.002 and 0.1 milligrams boron per liter. All told, boron moves through the atmosphere at a rate of 5 Mt to 7 Mt/a (5.5 million to 7.7 million stpy).

Jan 1, 2005

By S. K. Oraee

Most management decisions at all levels of the organization are as directly or indirectly depends on the circumstance of future. With regard to predict the future events in the process of decision-making plays a main role, therefore, forecasting is very important for every organizations and institutions. There is a variety of methods to predict time series. In general, these techniques can be divided as following: statistical, artificial intelligence and analytical techniques. Two of the most common methods for time series prediction is autoregressive integrated moving average (ARIMA) and artificial neural network (ANN) methods, these methods are the subset of statistical and artificial intelligence techniques respectively. In this paper, a hybrid model of ARIMA and ANN models are employed to predict the number of fatal injuries in the USA underground coal mines. This research showed the result of hybrid model is better than split model.

Jan 1, 2011

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world&apos;s phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By R. Gensemer

A number of state and federal agencies are calling for development of aquatic life criteria for conductivity. These aquatic life criteria or ?benchmarks? are based on observed correlations between conductivity and benthic macroinvertebrate community composition, generally measured by composite metrics or indices. However, development of an aquatic life criterion for a composite variable like conductivity is made difficult by a number of factors. Based on a database from West Virginia, observed patterns of invertebrate community composition versus conductivity may instead be related to a combination of abiotic (e.g., ionic composition, habitat) and biotic (e.g., life history, colonization potential) factors. Many benthic invertebrate taxa also do not respond to increasing conductivity in a consistent relationship. Many states have determined that a composite variable, like conductivity or TDS, is not appropriate for criteria development, as many studies have shown that toxicity varies as a function of ion composition and can be mitigated by elevated hardness. We conclude that the relationships between conductivity and changes in benthic macroinvertebrate community composition are neither strong nor reliable enough to warrant derivation of a criterion based solely on conductivity.

Jan 1, 2011

By W. H. Pomroy

In its 2001 diesel particulate matter (DPM) rule for metal and nonmetal underground mines, MSHA established an interim concentration limit of 400 micrograms of total carbon (TC) per cubic meter of air (400TCµg/m3), and a final concentration limit of 160TCµg/m3, to be phased in over five years. Following a court challenge to the 2001 rule, MSHA, industry and organized labor reached a partial settlement of the litigation under which the agency agreed to issue a proposal to amend the 2001 rule by, among other things, changing the surrogate from TC to elemental carbon (EC), applying MSHA&apos;s traditional hierarchy of controls, and revising requirements for one-year special extensions for complying with the final DPM exposure limit. MSHA issued a final rule in 2005 converting the interim concentration limit from 400TCµg/m3 to 308 micrograms of EC per cubic meter of air (308ECµg/m3) based on a miner?s personal exposure. Pending further rulemaking, MSHA retained the final concentration limit of 160TCµg/m3. In May 2006, MSHA issued a final rule that clarified that the final limit of 160TCµg/m3 would be based on a miner?s personal exposure rather than as a concentration limit. The 2006 rule also phased in the final DPM limit in three steps over two years, beginning in May 2006 at 308ECµg/m3, followed eight months later in January 2007 with a limit of 350TCµg/m3, and finally reaching 160TCµg/m3 in May 2008. Also in the 2006 rule, MSHA committed to converting the 160TCµg/m3 limit to an EC limit in future rulemaking. This paper reviews the DPM exposure limits in the context of the MSHA rulemakings and discusses the DPM engineering controls that were utilized by mine operators to attain compliance with each progressively lower limit.

Jan 1, 2009

By Brian E. Gombos

During early stages of the detailed design for Detroit?s Upper Rouge CSO Tunnel Project, a Value Engineering Recommendation suggested the design team investigate alternative concepts to the usual cast-in-place or precast concrete lining system for the Project?s many smaller diameter Deaeration Vent Shafts. The resulting design investigation produced not only an alternative lining system, but lead to a proposed non-conventional approach to shaft installation means and methods through soil and rock necessary to construct the permanent shaft lining system. This paper will outline and summarize the technical issues, contractual restrictions, and cost considerations that eventually lead to the final shaft design

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

By E. P. Deliac

The aim of this joint work between the French Coal Board and the Paris School of Mines is to be able to practically model the behaviour of a transverse drum cutting rock with picks. First a theoretical approach leads to the concept of cutting curves, giving forces and torque against penetration per drum revolution. Then experimental evidence, from full scale and reduced scale testing, validated and confirmed the theoretical shape of the curves. Finally practical applications are given, to improve the design or use of a shearer (or continuous miner). A micro-computer program is being developed to predict the cutting performances of a machine in certain conditions.

Jan 1, 1985

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009