Search Documents

By Miles T. Stephens, Felipe Calizaya, Jacob O. Kingston

Currently, the Bear Canyon Mine is facing the challenge of excessively high coal and rock temperatures in one of its headings. In Mine No.3, the air temperature at the 6th Right panel reached 36.4ºC and the coal 83.9 ºC. Due to these severe work conditions, the mining plan has been altered by changing the mine direction to avoid the high temperatures. To investigate the problem, drill holes were developed from the entries and the rock temperatures monitored using K-type thermocouples. The measurements confirmed the existence of localized “hot spots” in the mine. This paper presents a summary of ventilation surveys that were conducted in this mine. It includes the results of coal and rock temperature measurements from drill holes, interpretation of results using a heat flow simulator and the identification of hot spot areas. It also includes a summary of methods that were developed to reduce the hazard and control the problem.

Jan 1, 2005

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By I. T. Oramah

Despite the abundance of solid mineral deposits, Nigeria only earns about 0.5-1% of its current Gross Domestic Product (GDP) from the solid minerals sector. This is as a result of the dominance of the oil and gas industry, which has negatively affected the competitiveness of other sectors of Nigeria’s economy. The dominance of this industry has resulted in unemployment, poverty, hunger, domestic price inflation, corruption, unstable government, and higher exchange rates. These impacts are typical for economies suffering from the effects of "Dutch Disease" and the "Resource Curse". Community-based small-scale mining offers hope as an economic activity that can create wealth, employment, reduce hunger and poverty, and provide basic amenities for rural communities with solid minerals endowment. This study presents preliminary results of ongoing research into the prospects of using community-based small-scale mining in a developing country like Nigeria to move towards rural sustainable development.

Jan 1, 2011

By J. V. Ghelarducci, M. A. Sharpe, D. G. Chedgy

This article presents a novel design, called the Climax, High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 ~ 660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax, magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Feb 24, 1997

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal is still a part of energy generation worldwide and has a significant role in the sustainable development of countries. The amount of shallow coal deposits is getting scarce, making efficient underground mining operations crucial for both local and global economies. In underground mining operations, longwall mining is a commonly utilized method to extract deep coal deposits. One of the leading engineering goals in longwall mining is increasing the efficiency of the system by investigating the effects of operational factors on equipment. This paper investigates the shearer performance for a longwall top coal caving operation by discrete event simulation that includes modeling the double-drum shearer, belt conveyors, stage loader, and armored face conveyors (AFC) to evaluate system performance by considering the amount of daily coal production of the shearer. As a result, the most influential factor on mine production is determined and a data-based framework is developed. This study suggests a framework for data collection, data analysis, and the interpretation of the operational data to evaluate the primary production unit’s performance. The models developed for the face coal extraction operations in a longwall top coal caving (LTCC) mine have a bi-directional cutting system and can be implemented in other operations readily.

Jul 2, 2021

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By k. Osei-Boakye

This paper presents the calibration of a real-time aerosol monitor, the TSI DustTrak?, to the NIOSH 5040 method being used by the Mine Safety and Health Administration (MSHA) for compliance enforcement evaluation. The standard NIOSH 5040 instrument for compliance evaluation of diesel particulate matter (DPM) has an inherent time lag of up to two weeks for laboratory processing of sample results. Therefore, providing the underground mines with a means of quantifying DPM conditions in real-time, will enable them to efficiently and effectively manage DPM levels to ensure compliance with the regulated limit.

Jan 1, 2009

By Tim O’Neil

The earthmover tire shortage has been a case of bust and boom for the tire industry. Tire producers were unwilling to invest ahead of the mining boom. In their defense, though, the metals sector of the mining industry tends to be cyclic, tire manufacturers are not prescient. Until two years ago, low tire demand depressed prices. The incentive to invest in new, big-tire capacity was almost nonexistent, according to Prashant Prabhu, president of Michelin Earthmover Tire worldwide. “There has been very poor anticipation or a miscaluation of the amplitude of the (tire) demand on the part of just about everybody,” said Prabhu. What a turnaround. The earthmover tire market has grown by 30 percent over the past two years. Now there are not enough earth-mover tires and likely won’t be for the next two years. Goodyear said it was offering customers bias-ply tires when it could not supply enough radial-ply tires. Komatsu said it lost equipment sales because it could not provide the tires that customers requested. Volvo and Caterpillar said they are delivering some vehicles without tires, either promising tires later or leaving the customers – mine operators – to find their own rubber.

Jan 1, 2006

By F. Habashi

Asbestos, an extremely useful natural resource, has been studied extensively mineralogically and for industrial application. Its extraction from ores has been greatly improved with respect to safety in the work place. In spite of that, there is a decisive effort in many countries to ban its use on the grounds that it is a toxic substance. This action resulting in drastic decrease in production and the possibility of destroying the industry. The chelation of asbestos with organic dyes seems to be a promising way to abate its toxicity. Dyeing can be done when the fibers are slurred in water at ambient conditions in the same way as textile fibers.

Jan 1, 2009

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner's exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines' remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau's Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987

By Hiroshi Yamazaki

The paper describes prediction, control and validation of face pressures, and special TBM features for the bored tunnels of the New Metro Rail City Project, Perth, Australia. The selected EPB-TBM passed below a heritage bridge and the operational Perth Railway station in ground conditions consisting of fully saturated uniform sand combined with shallow overburden and a horizontal alignment radius of only 135m. Therefore, strict control of volume loss, TBM operations and ground movements was vital requiring continuous evaluation and adjustments to TBM operation parameters. The paper discusses the effectiveness of applied TBM face pressures and the used foam/polymer soil conditioning which was measured against achieved volume loss and the predicted range of ground settlements.

By L. M. Anisdahl

Ventiflex is a flexible ventilation duct system with a global market within mine and tunnel ventilation. The system is distributed in a wide range of qualities and dimensions. It is very important that ventilation systems are designed correctly in mines and tunnels. An incorrectly dimensioned system might result in bad air quality and too high costs. The objective of this study has been to assess some important design parameters for ventiflex comprising the friction loss factor for the duct wall itself, as well as the shock loss factors and the leakage factors for the different couplings systems. This has been obtained by carrying out a large scale experimental program on ducts with all the three different couplings: Velcro, zip and steel-ring. Pressure profiles and air flow rates have been measured, and based on these data the different factors have been calculated. The following results have been obtained: A friction factor l = 0,012 (K = 10) for the duct wall, a shock loss factor z = 0,0125 for velcro- and zip couplings, a shock loss factor z = 0,005 for steel-ring couplings, and a leakage factor f* = 0 mm2/m2 for all three coupling types. The latter result proves that no leakage is possible for a correctly installed duct with proper alignment. The results also confirm that ventiflex complies with class S, or better, according to the SIA-norm. However, whether ventiflex should be designed as class S, A or B according to the SIA-norm, depends on the particular application.

Jan 1, 2009

By Steve Kral

Competition from foreign coal producers could displace as much as 9 Mt/a (10 million stpy) of US coal bound for power plants located near waterways. But, according to a Maryland-based coal consultant, it could be worse. Theoretically, about 52 Mt (57 million st) of domestic coal could be vulnerable to imports by 1990, said Forrest Hill, of Hill & Associates of Annapolis. Hill was speaking to about 150 coal industry executives and experts at the third annual Coal Marketing Strategies Conference in November. Most were at the Denver, CO conference to pick up tips on how to sell coal in an oversupplied market. Imports threaten domestic markets Of the 200 utilities studied by Hill and his staff, 119 are situated near major waterways, he said. However, most of those waterways are not equipped to handle coal from the shipping lanes. Good news for US coal producers. But don't breathe too easily. Foreign coal still poses a major threat to domestic markets, Hill continued. The strength of the US dollar is an obvious factor. But easy access to US utilities located on waterways combined with low rates for ocean vessels give foreign producers another edge. And foreign mines are typically low cost producers. For example, Hill said Colombia's huge Cerrejon mine can deliver coal to an Illinois power plant for $47.87/t ($43.39 per st). That compares to $52.85/t ($47.95 per st) from a Kentucky coal mine. Also, Colombian coal producers can generate a cash flow even if the coal sells for $27.50/t ($25 per st). The main competition US producers face from abroad, as Hill sees it, comes from Australia, Canada, Colombia, Poland, South Africa, and, perhaps, from Venezuela. Domestic producers, however, do have some things going for them. Most US coal buyers, Hill said, "are not wild about the idea of buying foreign coal." A 10% price advantage or pressure from public utility commissions would be needed to force some of them to buy foreign coal, he said. Some of the utilities contacted said they would not commit to more than one-third of their stockpiles to a foreign source. Another advantage for US producers is that they have room in their long-term contracts to cut prices and still maintain a profit, Hill said. Railroads, too, have high profit margins written into their rate structures. They are also aware of the import threat. Therefore, they may reduce their rates accordingly to keep their markets. Marketing's role The energy price shocks of 1972 and 1976 caused major adjustments in world economics. Coal was no exception. High oil prices caused many utilities to look at less expensive coal. As the market improved, coal prices began to respond, said R. Gale Daniel, of Anaconda Minerals Co. But clean air legislation and the strengthening dollar caused havoc in the coal markets, he said. The price of oil crashed, taking with it predictions of record coal use. The result is an oversupply of coal that has led to price cutting. Now, coal marketing must be recognized in its "true leadership role," Daniel said. Marketing people must know when to use spot sales to balance production objectives and maintain cost-effective-

Jan 1, 1986

By Tom Martin

Mega projects present unique challenges with regard to estimating costs. With such projects, which may span decades, these challenges often begin as soon as a project is conceived. The importance of having a sound, resource based estimate avail-able early in the process cannot be overstated because it provides the basis for ongoing project decisions. For the final phase of providing an updated cost estimate, often while bidding by contractors is underway, the Engineer?s Estimate (EE) must incorporate present market conditions; account for possible volatile material price swings; be based on actual labor and fringe costs; rely on meaningful productivity rates; and accommodate any recent technology advances while identifying and allowing for risk factors. This paper explains the benefits associated with consultants adopting a contractor?s estimating approach when preparing the Engineer?s Estimate on mega projects like the various tunneling projects in New York City.

By S. E. Phillipson

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. Geology is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks, and an extensive crystal-lithic tuff debris apron. The ore body is hosted by intra-cauldron sedimentary rocks and breccias. Fluid inclusions suggest that silver, lead, and zinc were transported as chloride complexes and precipitated by cooling in veins from <5 wt. % NaCl eq. fluids at 170°-215° C. Silver associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2001

By Dan Armour

Bolting solutions traditionally offered only wet drilling or dry drilling options; each with advantages and disadvantages. Joy Mining Machinery has developed a Mist Drilling System that incorporates the best of both types of drilling. Compared to wet drilling, mist drilling offers as much as a 90% reduction in water use. As a result, floor and roof conditions are tremendously improved. This offers a safer and more comfortable work environment for operators. Mist drilling can offer a significant reduction in noise levels compared to dry drilling and in recent trials, bit life has been greatly improved. Holes are cleaner and operators experience less exposure to respirable dust.

Jan 1, 2005

By F. Freme

Coal production in the United States in 2007 totaled 1.03 Gt (1,145.6 million st), according to preliminary data from the Energy Information Administration (EIA) (Ta-ble 1). This is a decrease of 1.5 percent, or 15.6 Mt (17.2 million st) from the 2006 record level of 1.05 Gt (1,162.7 million st). Although coal production declined in 2007, U.S. total coal consumption increased for the year. Coal consumption in 2007 in the electric power sector was higher by 1.9 percent, while coking coal consumption decreased by 1.1 percent and the other industrial sector declined by 5 percent. (Note: all percentage change calculations are done at the short-tons level.) U.S. coal exports were significantly higher in 2007, while coal imports remained at about the same level. Total coal stocks increased slightly during the year, as some consumers continued to rebuild their stockpiles that had been seriously depleted in 2005 due to transportation issues. The growth in coal consumption during the year was primarily a result of the weather-related increases in the demand for electricity in 2007. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers) in the United States grew in 2007. Coal-based generation also increased, resulting in a 17.9-Mt (19.8-million-st) increase in coal consumed in the electric power sector. Coal use in the nonelectricity sector decreased by 3.8 percent to 74.7 Mt (82.4 million st). In the international markets in 2007, U.S. coal exports increased to levels not seen in recent years while coal imports were mostly static. U.S. coal exports totaled 53.7 Mt (59.2 million st), an increase of 8.6 Mt (9.5 million st) above 2006. Coal imports in 2007 ended the year at 32.9 Mt (36.3 million st), 91 kt (100,000 st) higher than in 2006. Coal prices in 2007 were split, with most domestic prices higher for the year while the international prices were overall lower. Although the average delivered price of coal increased for most users in the United States in 2007, the increases were smaller than what had been expe-

Jan 1, 2008