Search Documents

By X. J. Lyu, Q. Liu, M. J. Lian, X. Q. Cao, X. F. You, B. O. Erdenekhuyag, H. Y. Zang

The slag-tailings based artificial reef concrete (ARC) is made of CaO-CaSO4 activated granulated blast furnace slag (GBFS) as cementitious material and deslimed gold ore tailings as aggregate. In order to investigate the potential application of the material as ARC, the strength development, hydration characteristics and application performance were investigated under different preparation conditions. Results indicated that using seawater as the mixing water can effectively promote the hydration of slag and generate a large amount of hydration products such as ettringite, CSH gel, hydrotalcite and Friedel ’s salt in the early curing period and so render the material with good early compressive strength. Seawater curing can also accelerate the hydration reaction in the early stage of hydration. The hydration reaction of slag and the compressive strength of ARC can be effectively promoted by increasing the specific surface area of slag. The 28-day compressive strength of the slag-tailings based ARC prepared with 30-50% CaO-CaSO4 activated slag and 50-70% tailings can reach to 19.88-42.87 MPa. Also, the material has a low surface pH value, good resistance to chloride ion penetration, and sulfate corrosion. Keywords: Artificial reef concrete, granulated blast furnace slag, deslimed gold ore tailings, compressive strength, hydration characteristics

Jan 1, 2020

By M. Karsten

Platinum mines in the Bushveld Complex are located in areas with a high geothermal gradient. This means that, compared to, for example, gold mines of the Witwatersrand region, high rock temperatures are encountered at relatively shallower depths. Thus air cooling and refrigeration need to be considered at early stages in mine development. Another factor that influences air cooling and ventilation requirements is the use of trackless diesel equipment for loading and hauling broken rock. At shallower depths it will be more cost-effective to locate the cooling and ventilation equipment on surface, whereas for deeper mines the more cost-effective option is to locate cooling equipment underground. For intermediate depths, trade-off studies need to be undertaken to determine the optimum mix between more cooling and less air or more air and less cooling, as well as the optimum location for this cooling equipment. Factors that are taken into account include power requirements, positional efficiency, and additional infrastructure requirements. Traditionally the approach has been to ventilate ?all of the mine all of the time?. However, with increasing power costs and growing pressure to ensure sustainability, this strategy must be modified to apply ventilation and cooling on demand. In other words, both cooling and ventilation equipment should be operated only when needed and should be adjusted to the demand at the time. Obviously there will be areas that will need to be ventilated (and cooled) continuously (for example, for dilution of flammable gases), but this can be built in to the overall strategy. In addition, in devising ventilation on demand (VoD) strategies, occupational criteria relating to exposure to gases, noise, and heat need to be taken into account. This paper discusses options available for implementing energy-efficient ventilation and cooling systems and suggests ways of changing traditional thinking in the overall ventilation and cooling of mines. Efficient ventilation and cooling designs can play a major role in improving sustainability and reducing energy costs and carbon footprint.

Jan 1, 2012

By Z. Szczepanik, D. Milne, K. Kostakis

Abstract This paper presents the results of a series of creep tests performed on a total of nine samples of Lac du Bonnet granite from the Underground Research Laboratory near Pinawa, Canada. Each of the nine samples were subjected to stresses in excess of 80% of the average uniaxial compressive strength of the granite and were maintained at that level of constant loading for periods of time ranging between a few minutes and several months. Acoustic emission was recorded in order to monitor the development and accumulation of brittle microfracture damage in the samples throughout the long-term loading. According to previously published theoretical predictions and field results, as well as similar experimental results of creep tests in granite, samples should fail when loaded to 70% of their UCS for an extended period of time. Six of the samples did not fail when subjected to stresses in excess of 80% of their UCS over periods of several months and were subsequently subjected to uniaxial compression to failure. The average strength of the samples that had previously been subjected to long-term loading were comparable to the average published strength of this rock. Three of the nine samples had increased end confinement and these three samples failed under long term loading. Résumé Cet article présente les résultats d'une série d'essais de fluage de roche exécutés sur neuf échantillons de granite de Lac du Bonnet, du laboratoire souterrain de recherches près de Pinawa, Canada. Chacun des neuf échantillons a été alors soumis aux charges au-dessus de 80% de la résistance à la UCS moyenne du granit et a été maintenu à ce niveau du chargement constant pendant des périodes s'étendant entre quelques minutes et plusieurs mois. L'émission acoustique a été enregistrée pendant les essais afin d'obtenir des indications des dommages pendant le chargement à long terme. Selon des résultats théoriques précédemment édités et les résultats expérimentaux semblables des essais à long terme en granite, échantillons devrait échouer si chargé à 70% de leur UCS pendant une période prolongée. Six des échantillons n'ont pas cassé quant ils ont été soumis aux charges au-dessus de 80% de leur UCS et ont été plus tard soumis à la compression uniaxiale à la rupture. La force moyenne des échantillons qui avaient été précédemment soumis au chargement à long terme étaient comparable à la force éditée moyenne de cette roche. Trois des neuf échantillons avaient augmenté le confinement de fin et ces trois échantillons ont cassé sous le chargement à long terme. Zusammenfassung Dieser Artikel beschreibt die Resultate von Kriechversuchen, die an neun Proben aus dem Lac du Bonnet Granit des "Underground Research Laboratory" bei Pinawa in Kanada durchgeführt wurden. Jede der neun Proben wurde Drücken unterworfen, die mehr als 80% der einaxialen Druckfestigkeit des Granites entsprechen. Diese Drücke wurden für verschiedene Zeitspannen von wenigen Minuten bis zu einigen Monaten auf einem konstanten Niveau gehalten. Während der gesamten Langzeitbelastung wurden akustische Emissionen aufgezeichnet, um die Entwicklung und gesamthafte Beschädigung der Proben durch Sprödbruch aufzuzeichnen. Entsprechend bisher veröffentlichter theoretischer Vorhersagen, Feldversuchen und auch experimentellen Resultaten von Kriechversuchen an Granitproben wäre ein Versagen der Proben zu erwarten gewesen, wenn sie über längere Zeit einer Last von 70% ihrer einaxialen Druckfestigkeit unterworfen werden. Wider Erwarten trat bei sechs der Proben kein Versagen ein, als sie mit über 80% ihrer einaxialen Druckfestigkeit über mehrere Monate belastet wurden; daher wurden sie im Anschluss bei einaxialer Kompression zum Versagen gebracht. Die mittleren Festigkeiten der im Langzeittest verwendeten Proben sind vergleichbar mit den normalerweise für diesen Gesteinstyp angegebenen Festigkeiten. Drei der neun Proben versagten unter der Langzeitbelastung; diese drei Proben hatten eine erhöhte Endflächenreibung.

Jan 1, 2003

By H. Schunnesson, H. Fredriksson, D. Johansson, E. Söderström, S. Manzoor, A. Gustafson, M. Danielsson

Fragmentation analysis is an essential part of the optimization process in any mining operation. The costs of loading, hauling, and crushing the rock are strongly influenced by the size distribution of the blasted rock. Several direct and indirect methods are used to analyse or predict fragmentation, but none is entirely applicable to fragmentation assessment in sublevel caving mines, mainly because of the limitations imposed by the underground environment and the lack of all the required data to adequately describe the rock mass. Over the past few years, measurement while drilling (MWD) data has emerged as a potential tool to provide more information about the in-situ rock mass. This research investigated if MWD can be used to predict rock fragmentation in sublevel caving. The MWD data obtained from a sublevel caving mine in northern Sweden were used to find the relationship between rock fragmentation and the nature of the rock mass. The loading operation of the mine was filmed for more than 12 months to capture images of loaded load-haul-dump (LHD) buckets. The blasted material in those buckets was classified into four categories based on the median particle size (X50). The results showed a stronger correlation for fine and medium fragmented material with rock type (MWD data) than coarser material. The paper presents a model for prediction of fragmentation, which concludes that it is possible to use MWD data for fragmentation prediction.

Mar 2, 2022

By M. A. Mahboob, T. Celik, B. Genc, I. Atif, S. Ali

"Mapping of hydrothermally altered areas, which are usually associated with mineralization, is essential in mineral exploration. In this research, open source reflectance spectroscopy data from the multispectral moderate-resolution Landsat 8 satellite was used to map altered rocks in the Gauteng and Mpumalanga provinces of South Africa. The unique spectral reflectance and absorption characteristics of remotely sensed Landsat data in the visible, near-infrared (NIR), shortwave-infrared (SWIR) and thermal infrared (TIR) regions of the electromagnetic spectrum were used in different digital image processing techniques. The band ratios (red/blue, SWIR 2/NIR, SWIR 1/NIR), spectral band combinations (Kaufmann ratio, Sabins ratio) and principal component analysis (Crosta technique) were applied to efficiently and successfully map hydrothermal alteration minerals. The results showed that the combination of spectral bands and the principal component analysis method is effective in delineating mineral alteration through remotely sensed satellite data. The validation of results by using the published mineral maps of the Council for Geoscience South Africa showed a good relationship with the identified zones of mineralization. The methodology developed in this study is cost-effective and time-saving, and can be applied to inaccessible and/or new areas with limited ground-based knowledge to obtain reliable and up-to-date mineral information.IntroductionMany developing nations depend on exploration and exploitation of mineral resources to sustain their economic growth. Usually, the traditional mineral exploration techniques require enormous finances, prolonged time, and tremendous manpower, particularly in areas that are not easily reachable (Maduaka, 2014). Furthermore, mineral exploration required state-of-the-art techniques and expertise along with geological, geochemical, and geophysical datasets, which may not be easily available or may be lacking where access is problematic (Kaiser et al., 2002; Bemis et al., 2014). Modern remote sensing technology has proved to be one of the highly efficient and robust techniques used for mineral exploration. The use of remote sensing satellite images for geological mapping and mineral exploration usually involves studying the physicochemical properties of rocks and weathering soils, such as mineralogy, landforms, geochemical signatures, and the spatiall distribution of lineaments (Bhattacharya et al., 2012)."

Mar 1, 2019

By Dick Minnitt

Large-scale variability in process plants and process control can be identified and controlled through disaggregating the overall variability in a process stream. Conventional statistics and Statistical Process Control (SPC) fail to address the concept of stream heterogeneity, therefore fail to identify and distinguish between the various sources of variability in a process stream. A modified set of 445 data from a process plant is used as an example to explain the benefits of variography in process control. Large-scale variability, usually in the form of product composition cycles and chemical cyclic variations may be manifest throughout a sampling system or a process plant, but this type of variability is most easily discernable in one-dimensional process streams. The Moving Average is a powerful tool for identifying large and small scale variability and cyclical behaviour in process streams, while the variogram is a custom built tool that allows the components of variability to be identified and resolved. The positions in the variogram at which the different variance can be read and the nomenclature of these types of variability is described. The transfer of variances converted to standard deviations to the Control Charts, allows an operator to appreciate the appropriateness of Upper and Lower control and specification limits. The overall contribution of the various sources of variability is represented in a pie diagram.

Jan 1, 2007

By W. Newcomen, D. Brox

The assessment of the stability performance of open pit highwalls has traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work has been reviewed and are endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on relatively consistent trends in highwall strain data. L’évaluation du niveau de stabilité des hauts murs de carrières a traditionnellement été basée sur les taux de mouvements de surfaces. Bien que cette approche soit généralement acceptée à travers l’industrie, elle présente des défis pour la définition de seuils appropriés concernant la sécurité des opérations minières et n’adresse pas la notion de déformations totales. Des données de mouvements de surface provenant d’un nombre limité d’opérations minières à ciel ouvert d’Amérique du Nord et du Sud ont été évaluées en terme de déformation des hauts murs, de qualité de la masse rocheuse et des mécanismes inférés d’instabilité. Des seuils de déformation pour différentes phases clefs de stabilité de hauts murs ont été revus et sont endossés, basé sur l'évaluation de donnés additionnelles. Un critère de déformation empirique pour l’évaluation de la stabilité des hauts murs est postulé, basé sur des tendances relativement consistantes de données de déformations de hauts murs. Die Beurteilung der Stabilität von hohen Felsböschungen basiert traditionellerweise von Oberflächenbewegungen. Obwohl dieses Verfahren im Allgemeinen akzeptiert wird, stellt es jedoch gewisse Probleme für die Festlegung von Grenzwerten für die Sicherheit dar. Die totalen Dehnungen werden bei dieser Betrachtungsweise vernachlässigt. Eine beschränkte Anzahl von Oberflächenbewegungs Daten von Bergbauwerke in Nord- und Südamerika sind in Bezug auf die Dehnungen von hohen Felsböschungen, Felsqualität und davon abgeleiteten Bruchmechanismen untersucht worden. Grenzwerte für die Belastung von hohen Felsböschungen während den massgebenden Bauetappen aus bisherigen Projekten sind begutachtet und durch zusätzliche Untersuchungen bestätigt worden. Gestützt auf relativ konsitenten Trends, ist hier ein empirisches Verfahren der Dehnungen in hohen Felsböschungen zur Beurteilung der Stabilität vorgestellt.

Jan 1, 2003

By S. W. Robertson, M. T. Golela, S. Mxinwa

South Africa has one of the largest Cr-related industries in the world and generates large amounts of Cr-containing smelter dusts. It is normal practice to scrub Cr from the furnace off-gas in water, and to recover the Cr by adsorption, followed by recycling of the loaded adsorbent into the furnace. A study was conducted to find a low-cost adsorbent that is capable of removing sufficient Cr from the solutions generated by scrubbing. The test work focused on the evaluation of different clay minerals (attapulgite, bentonite, and kaolinite) as adsorbents for Cr. Cr(VI) could only be adsorbed after prereduction with e.g. ascorbic acid (ASA). An 80% removal of Cr(VI) could be achieved from a solution containing 20 mg/L Cr using bentonite clay after reduction with ASA. Attapulgite and kaolinite adsorbed less than 55% Cr after reduction with ASA. Both ASA and ferrous salts were found to be suitable reducing agents. The use of acid mine drainage (AMD) was also investigated as a low-cost alternative reducing agent, as AMD usually contains iron. The Cr(VI) reduction potential of the AMD was determined by redox titration against a solution containing 50 mg/L Cr(VI). Studies show that AMD can potentially be used as a reducing agent in a Cr removal process if it is available on site.

Feb 12, 2024

By C. Erichsen

ABSTRACT: The Berg Bock Freeway Tunnel represents the southernmost link of the "Thuringian tunnel chain" of the new freeway A71 located in the eastern part of Germany. It comprises two tubes each 2700 m in length. From north to south, it passes through the Suhl granite, the base sediments and the porphyrite of the New Red as well as the layers of the Middle Bunter. The two tunnel tubes were driven by the shotcrete method within appr. 10 months. With four tunnel faces, maximum performances totalling appr. 30 m/d were attained. Additional, supplementary demands on the safety conception, resulting from the findings from and the analysis of fire accidents in tunnels in recent years, had to be fulfilled in the execution planning at short notice. The inner lining is largely constructed using non-reinforced concrete. Reinforcement is only installed in the portal zones, in tunnel sections in less stable rock and in areas with a special cross-section as for instance cross connections and niches. ZUSAMMENFASSUNG: Der Autobahntunnel Berg Bock stellt das südlichste Glied der "Thüringer Tunnelkette" auf der Autobahn A71 dar, die im Osten von Deutschland liegt. Er besteht aus zwei Röhren von je 2700 m Länge. Vom Norden nach Süden durchörtert er den Suhler Granit, die Basissedimente und den Porphyrit des Rotliegenden, sowie die Schichten des Mittleren Buntsandsteins. Die beiden Tunnelröhren wurden in Spritzbetonbauweise in einer Bauzeit von etwa zehn Monaten aufgefahren. An vier Vortriebsorten wurden Spitzenleistungen von insgesamt etwa 30 m/d erzielt. Ergänzende Anforderungen an das Sicherheitskonzept, die sich auf der Grundlage der Auswertung der in den letzten Jahren aufgetretenen Brandunfälle in Tunneln ergeben haben, wurden im Rahmen der Ausführungsplanung kurzfristig berücksichtigt. Die Tunnelinnenschale wurde weitgehend aus nicht bewehrtem Beton hergestellt. Nur in den Portalzonen, in Tunnelabschnitten mit weniger standsicherem Fels und in Bereichen mit speziellen Querschnitten, wie beispielsweise im Bereich von Querstollen und Nischen, wurde bewehrter Beton ausgeführt. RÉSUMÉ: Le tunnel d'autoroute de Berg Bock représente le plus méridional maillon de la "chaîne thuringienne de tunnels" sur l'autoroute A71 dans l'est de l'Allemagne. Il se compose de deux tubes d'une longueur de 2700 m chacun. Du nord vers le sud, il traverse le granit de Suhl, les sédiments de base et le porphyrite du Rotliegendes, aussi que les strates du grès bigarré intermédiaire. Les deux tubes étaient creusés en méthode de construction de béton projeté dans une période de construction d'environ dix mois. À quatre fronts de taille rendements maximaux collectifs d'environ 30 m par jour étaient obtenus. On a eu égard à court terme dans la conception d'exécution à des demandes supplémentaires vers la conception de sécurité, qui ont résulté sur la base de l'interprétation des accidents d'incendie dans des tunnels dans les années dernières. La paroi intérieure était construite largement de béton non armé.

Jan 1, 2003

By T. H. Yang, Q. K. Wang, T. Song, J. W. Zhou

The grinding circuit can be one of the most important mineral processing circuits in plants. Along with the application of large-scale milling machines, the design and optimisation of the operation strategy for grinding circuits is more complicated. An in-house grinding process simulation tool was developed to mass balance, model fit and simulate crushing, grinding and classification circuits. An industrial grinding and classification circuit in a copper mine was modelled, and the modelling parameters were verified by a particular group of plant survey data. To justify the prediction ability of the fitted models, the model predictions under different operation conditions were compared with another group of plant survey data. Then the model predicted the effects on the circuit of changing operating conditions. Circuit analysis of the comminution process for water feed to a SAG mill, water feed to sump, the rolling speed of a SAG mill and the percentage of ball filling in a SAG mill was put into practise, based on the simulation results. The simulation results can be used to help plant operators understand the features of the comminution process and may help to build a knowledge library for process control. Keywords: Process modelling, grinding, comminution, circuit analysis

Jan 1, 2020

By L. J. Gerber, O. D. Eniowo, L. D. Meyer, S. R. Kilambo

Artisanal and small-scale mining (ASM) operations continue to grow across sub-Saharan Africa and serve as a source of livelihood to many rural communities. Owing to safety, health, environmental, and social concerns, the occupation has been regarded as a menace in several sub-Sahara African countries. Recent studies in the field of ASM prescribe formalization as a way to tame its excesses while enhancing its potential. This paper explores the concept of formalization as it relates to ASM and how it is being affected by the funding situation. The paper seeks to address the question as to whether formalization of artisanal mining operations can achieve the desired results in view of the lingering credit constraints in this mining subsector. It is recommended that, as a way of extending the scope of formalization, focus should be placed not only on access to credit in ASM but also towards optimizing the creditworthiness of ASM firms, with the goal of improving the viability of the operations.

Mar 2, 2022

By P. Henning

Rock fall accidents continue to be the main cause of fatal and serious injuries in the mining industry. Although there has been an improvement in the FOG (falls of ground) related fatal and serious injuries over the past few years, the rate is still too high. New technology has made it possible to reduce this rate significantly. FOG accidents imply failure of the support system or the design of the support system in use. In this paper we deal with the latest technology available to assist the mines to reduce the rates of FOG related injuries and fatalities.

Jan 1, 2010

By K McLeod

{Figure 1} The Placer Dome-Western Areas Joint Venture?s South Deep Twin Shaft Complex, has been planned and dreamt of for nearly 20 years. [ ] The gold reserve at the bottom of these shafts is one of the largest single intact gold deposits remaining in the world today, containing an estimated 57 million ounces. This is about the size of the fictitious reserve created by inventive prospectors for the infamous BREEX scam in Kalimantan about ten years ago and about the size of the reserve Harmony claims as its own in it?s current hostile takeover bid for Gold Fields. So it is certainly of the magnitude that dreams are made of. [ ] {Figure 2} The unique orebody lies in a continuous, highly concentrated, thick deposit, an estimated twelve kilometres along dip and a two kilometre wide strike. Due to the thickness of some sections of the reef, up to 60 metres in places, bulk mining methods will be required for it?s extraction. [ ] {Figure 3} The twin shaft system comprises a main shaft which had an initial design depth of 2765m and a ventilation shaft of 2760m, making them the world?s deepest to be sunk in a single lift. The shafts were

Jan 1, 2005

"Chairman: Professor J. Elbrond Rapporteur: Miss V. E. MartingPapers.Aids to planning production in coal mines by F. H. Deist and M. P. RobertsCapacity calculations, investment allocation and long-range production scheduling in German coal mines by F. L. WilkeOre reserve evaluation and open pit planning by J. M. Marino and J. P. SlamaThis session was devoted to the economic aspects of planning and scheduling. After Dr F. H. Deist had introduced the paper Aids to planning production in coal mines, Dr T. V. Falkie summarized the following formal contribution prepared jointly with Dr R. V. Ramani, describing the work that has been done at the Pennsylvania State University in the development of simulation programs for mine planning over the past 15 years:During the late 50's and early 60's, Monte Carlo simulators were developed to model continuous miner-shuttle car transport systems, track haulage systems, belt conveyor networks, etc. In the mid-60's attention was directed towards deterministic simulation of equipment performance, given the equipment characteristics and the system profile. In the late (10's all these systems (miners, shuttle cars, belts and trains) were integrated together to form a complete coal mine simulator and the program could predict the output potential of the system, given the mining dimensions, method and equipment employed. The actual sequence of coal-cutting operations is entered into the computer through the use of a special programming language which permits any type of mining configuration to be simulated. The simulator is hybrid in nature in that the shuttle cars, trains and belts are simulated deterministically, whereas rate functions with delay frequencies are entered for the continuous mining operations of sumping, shearing, fleeting, cleaning, etc. With suitable manipulation of the data, the program may be applied to all belt or conventional mining sections. Most of these simulators were developed through the assistance of grants from the Department of Mines and Mineral Industries of the Commonwealth of Pennsylvania and are available from the Coal Research Board of the Commonwealth,"

Jan 1, 2014

By P. Marinos, G. Tsiambaos, H. Saroglou

The anisotropic behaviour of “Athens Schist” has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the “Athens Schist” were statistically analysed and evaluated. Le comportement anisotropique des roches du système “Schistes d’ Athènes” a été déterminé sur des épreuves avec une orientation différente de la schistosité par rapport à l’axe de chargement sous des conditions axiales, triaxiales et dynamiques. Un grand nombre des résultats a été statistiquement analysé et discuté. Zur Bestimmung der anisotropen Eigenschaften der Athen Schiefer wurden einaxialen, dreiaxialen und dynamischen Kompressionsversuchen an Gesteinskernen durchgeführt, bei denen die Belastungsachse verschiedenen Neigungen gegen die Schieferung hat. Die Messreihen an anisotropen unzerreissbaren Fels Samplen von Athen Schiefer wurden statistisch analysiert.

Jan 1, 2003

By C. Chingwaru, W. Chingwaru, J. Vidmar

"Zimbabwe is endowed with rich deposits of minerals such as diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching has been implemented as an efficient and low-cost method to extract metals such as copper, cobalt, and gold from sulphide and/or ironcontaining ores and mineral concentrates in a number of countries around the globe. Zimbabwe, despite being a world leader in mineral wealth, has gone through years of economic stagnation which have brought with them energy shortages. Bioleaching is an innovative way to recover minerals from ores using relatively low-capital-cost and non-polluting technology. Principally, iron- and sulphur-oxidizing bacteria can be used to oxidize iron and sulphide to ferric iron and sulphuric acid, respectively, and the ferric iron oxidizes the insoluble metal sulphides to soluble metal sulphates that can be readily recovered from solution. Although some minerals such as gold are inert to biological reactions, they can be liberated using bacteria that act on certain types of ores and other minerals that co-occur with these minerals. The geology of the mineralized areas in Zimbabwe, rich in chalcopyrite / pyrite, allows a number of microorganisms to be used for the extraction of minerals by bio-oxidation. This paper reviews the potential of bioleaching in the country. IntroductionZimbabwe has rich deposits of minerals including diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching is defined as the use of microorganisms to facilitate the extraction of metals from sulphide or iron-containing ores or concentrates (Rawlings, 2004, 1997). Bioleaching has been shown to be an efficient (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004) and low-cost (Schippers et al., 2010) method to extract minerals in many countries around the globe. For example, aerobic Fe(II)- and sulphur-oxidizing bacteria have been shown to be up to two orders of magnitude more efficient in the oxidation of pyrite than the chemical processes (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004). Additionally, bioleaching can be used to extract minerals from low-grade ores, sulphidic waste rock dumps, and tailings efficiently (Schippers et al., 2010)."

Jan 1, 2017

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006

The response was good-one of the best the SAIMM has had to its various questionnaires. 231 replies were received from 2768 members representing a response of 8,35%. For fellows and Members together, the response was 13,7%. The spread of responses based on respondents' work situation appeared to be well balanced with some bias from those in consulting organizations. Members' perceptions of their employers' positions withrespect to environmental management looked somewhat optimistic, but it is encouraging to note that they reported that more than half were developing environmental management systems. Training of varying degree was taking place at al levels in their organizations. Members saw their Institute as an important agent inlifting environmental awareness, literacy and responsibility not only through the journal and symposia, but also by liaison with government departments and educational institutions. Most respondents saw environmental legislation both from local and overseas sources as affecting their organizations, their products and services with the emphasis on corporate image, core business and sales.

Jan 1, 1995

By M. M. Oosterveld

"In South West Africa diamonds are mined from ancient beach deposits by the Consolidated Diamond Mines of South West Africa, Limited.To improve the control of mining production, a computer is used for the calculation of statistically more accurate and homogeneous ore blocks. Geological and sampling information has been digitized and stored on magnetic files.The figures derived for each block entail the calculation of the diamond size frequency distribution, the diamond density distribution and the ore reserve by using the density distribution.The diamond size frequency distribution is used for estimating the revenue in an ore block.A description is given of how a linear programming system can be used for production planning."

Jan 1, 2014

By M. Pötsch, M. Blümel, E. A. Button

ABSTRACT: Stiffness controlled test procedures performed with servo-controlled shear systems are the most versatile for simulating the wide range of boundary conditions expected in nature. Examples of a function controlled procedure in addition to dilatation controlled procedures are discussed for different characteristic behaviours. ZUSAMMENFASSUNG: Steifigkeitskontrollierte Scherversuche mit servohydraulischer Steuerung eignen sich gut unterschiedliche Bettungen, wie auch in der Natur vorkommen, zu simulieren. Beispiele für spezielle Steuerungsfunktionen und dilatationsgesteuerte Prozeduren mit verschiedenen charakteristischen Eigenschaften werden diskutiert. RESUMÉ: La rigidité a commandé des méthodes d'essai exécutées avec les systèmes asservis de cisaillement sont la plus souple pour simuler l'éventail d'états de frontière prévus en nature. Des exemples d'un procédé commandé par fonction en plus des procédures commandées par dilatation sont discutés pour différents comportements caractéristiques.

Jan 1, 2003