Search Documents

By John C. Hartley

Large areas of the anthracite beds in the Wilkes-Barre, Pa., region have been first-mined in such a manner that over half of the original coal has been left underground as pillars to support the overburden. To recover the maximum amount of this remaining coal, improved devices to support the roof while pillars are being extracted are needed. Also needed are suitable backfilling systems that will stabilize the strata during the mining and effectively limit the inevitable subsidence after pillars are removed. Accordingly, the Federal Bureau of Mines furnished 400 yielding steel props that had been purchased abroad, where this type of prop had been used successfully. The cooperating company arranged for concurrent tests with a mechanical stower designed and built by an American manufacturer. In the area in which the experiments were conducted, pillar removal, using conventional timbering, was most difficult because the roof fractured badly, the installation of timbers consumed a substantial part of the work effort, and some coal nearly always was lost. With the application of the yielding props, the time needed for securing the roof was reduced 33.9 percent; production per man-shift was in¬creased over 33 percent; coal recovery was improved more than 9 percent; and the convergence between roof and floor, during mining and backfilling, amounted to as much as 8.03 inches without any break in the roof. However, in September 1953 some roof rock fell in pillar 10 owing to insufficient props in a small area where the ends of three top holes drilled in the coal face extended up into the roof rock.

Jan 1, 1956

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By BUREAU OF MINES

This report is submitted in accordance with provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U. S. C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1954 has been divided into two separate publications. Each is being published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5118, Part I - R. I. 5119, Part II - 011 From Coal. 011 From 011 Shale. The introduction, identical in both reports, summarizes research progress in 1954 under the entire Synthetic Liquid Fuels program. A free copy of either publication may be obtained by writing to the Bureau of Mines, Publications Distribution Sec- tion, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Mar 1, 1955

By R. F. Randolph, R. S. Fowkes, J. J. McClelland, G. H. Schnakenberg

Between 1986 and 1992, there were268 deaths and 54,642 severe injuries to workers in underground U. S. mining operations. Clearly, this level of health and safety risk is not acceptable. While most underground coal mining jobs are dangerous, some are much more dangerous than others. Many jobs in an underground coal mine are clustered around the working face—the place where machinery digs coal from the surrounding rock. The hazards in this area are numerous: When the coal is removed, the ground around it becomes unstable and can cave in on the workers. The mining machines used there are large, heavy, powerful, and move in many different directions in a very confined space, presenting danger to workers. Also, the machines churn up coal dust that causes black lung and other ailments. Figure1 shows a modern radio remote controlled continuous mining machine and its operator. In a typical mine, the jobs with the greatest exposure to hazards involve operation of machinery that cuts tunnel-like passages into the coal (the continuous mining machine) and machines that insert supportive steel bolts into the rock above the work area (roof bolting machines). The workers who endure these hazards are at almost twice the risk of death or disabling injury than co-workers in other safer areas of the mine. Of the statistics quoted above, 106 of the 268 deaths and 21,552 of the 54,642 severe injuries occurred in jobs involving equipment at the working face. The operators of roof bolting and continuous mining machines account for only 21% of the work force but suffered 40% of the deaths and 39% of the lost-time injuries during1986-1992. These death and injury rates are almost twice the rate for workers in other underground mining jobs (see figure 2). The estimated total cost of the 106 fatalities and21,552 lost-time injuries was $327 million from 1986-1992. On average, each fatality cost over $1 million and each lost-time injury costs in excess of $9,000.

Jan 1, 1994

By Kenneth H. Johnston

The Weber pool in Washington County, Okla. (fig. 1), covers an area extending from 2 miles east and slightly north of Bartlesville, Okla., to a point approximately 2-1P tiles northeast of Dewey, Okla. The pool is a part of the area designated by the Standing Committee on Oil Field Nomenclature, Kansas-Oklahoma Division, Mid-Continent Oil & Gas Association, as the Bartlesville-Dewey field. In the following discussion of the geology, development, and exploitation of the Weber pool, the writers, by means of structure maps, cross sections through various parts of the reservoir, and tabulated development data and production statistics, have recorded salient information on a field that was developed before .1910 in an Area that has been repressured since 1926. The total oil production to January 1, 19.0., from the 2,639 developed acres considered in this report, was approximately 14 million barrels, or a recovery of about 5,3;2 barrels per acre, or 227 barrels per acre-foot. The production of the estimated 18 million barrels of recoverable oil remaining in the Bartlesville sand reservoir will require the initiation of additional secondary-recovery practices on some of the leases and the application of a more systematic repressuring program on others.

Jan 1, 1950

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By Diana K. Schimmelpfennig

Assessment of revegetation success on mined lands is a difficult, time consuming task and has been the subject of a number of controversies. Present regulations require that both plant cover and aboveground plant biomass be measured for use in making that assessment. Of these two variables, biomass is the most time consuming to measure and requires destructive sampling, a most undesirable requirement on fragile, recently revegetated areas. On the other hand, plant cover can be estimated using the point-frame method which is relatively nondestructive. In addition, vegetation can be sampled more uniformly with the point frame and in less time if species composition measures are to be made. A study was done to evaluate the predictability of aboveground biomass production on revegetated mined sites and adjacent native prairies using plant cover estimates made with the point frame method. The predictability of biomass production by cover estimates bears on the need for both measurements in assessing revegetation success. In general, a positive, statistically, significant correlation was demonstrated between plant cover (estimated by the point frame) and aboveground biomass (estimated by the harvest method) regardless of community type (mined or native), species composition, diversity or level of biomass production. However, the latter did have their effects on the relationship and must be accounted for in any predictive equations (that is to say, the predictive equations must be considered site-specific). Considering the relationship observed between the two parameters, cover estimation may be a sufficient indicator of revegetation success, especially where time and minimization of disturbance are critical.

Jan 1, 1982

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from the underlying unoxidized ore through prolonged Weathering. The degree of oxidation in different sections and at different depths within the bed is not uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By R. R. Sayers

Although the attention of those interested in diseases peculiar to mining as teen focused recently on one duct disease - silicosis - other respiratory diseases may cause more suffering and economic loss. The increased incidence of these diseases usually is attributed to exposure to abnormal air conditions underground, such as sudden changes from high to low temperatures, excessive dust, and noxious gases. The principal respiratory diseases to which the mine is subject axe bronchitis, influenza and pneumonia, pulmonary tuberculosis, anthracosilicosis, and. silicosis. Although the mortality statistics in some of the tables included in this paper are old they have been corroborated by later, lees complete data Bronchitis Bronchitis is en inflammation of the bronchial tubes due, among other causes, to the inhalation of irritants such as dusts (organic and inorganic). Occupations that entail exposure to atmospheres polluted, by irritating gases carry with them the risk of bronchitis. According to Collie (1), it cannot be distinguished clinically from bronchitis occurring among the general population, and its association with tae inhalation of dust or gases usually is unrecognized.

Jan 1, 1941

By D. L. Paulson

The Bureau of Mines used 50-and 800-kva electric-arc furnaces to confirm the feasibility of producing ferronickel in electric-arc furnaces from pre-reduced concentrate from the Yugoslavian FENI project. The relationships were established among metallic iron concentrations (degrees of prereduction), ferronickel grades, and nickel recoveries. Smelting the concentrate containing 1.27 wt-pct nickel and metallic iron levels between 2 and 3 wt-pct, produced 15 to 20 pct ferronickel. Higher or lower metallic iron concentrations were compensated by adding oxide pellets or carbon to the electric-arc furnace charge. Over 90 pct of the contained nickel was recovered when up to 20 pct ferronickel was being produced. Data obtained while smelting 16 tons of prereduced concentrate in the 800-kva electric-arc furnace indicated ferronickel can be recovered at an energy consumption of 530 kwhr/ton of prereduced material.

Jan 1, 1977

By Daniel I. Carey

Current and potential dragline reclamation usage was evaluated for the U.S. coalfields based on data gathered and analyzed during field surveys, literature reviews and contacts with manufacturers. It was concluded that current mining plans have been adapted to federal and state strip mine and reclamation laws in ways which limit the potential for dragline reclamation systems at active mine sites. At abandoned conventional contour mine sites in steep-sloping areas such as central Appalachia, however, it was found that dragline reclamation systems have great potential application and may be the only practical solution to many reclamation problems. Alternative dragline systems were examined for restoring abandoned sites, and it was concluded that a tower excavator system offered superior characteristics and should be evaluated and developed under field conditions. A testing program was developed to provide a framework for the monitoring and analysis of cost, production and environmental data during a field demonstration of a tower excavator system.

Jan 1, 1981

By D. D. Hamilton

The ISMS program provided for the development and demonstration of equipment modifications for improved safety in both conventional and continuous coal mining systems. This report documents the success of the program in identifying accident hazards in underground coal mines with 4-to 8-foot seam heights, in designing modifications to reduce the hazards, and in demonstrating improved safety through extended underground use of the ISMS equipment.

Jan 1, 1977

By R. F. Droullard

The Bureau of Mines has used gross alpha and gross beta detectors to continuously measure radiation working levels for a number of years. During this time, improvements have been made in the design and performance of continuous working-level (CWL) detectors. This report discusses the improved designs and some of the operating principles and applications of CWL detectors in the measurement of radon daughter products in mines and dwellings.

Jan 1, 1985

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining I research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and, the results are described in this report.

Jan 1, 1983

By G. R. Strimbeck

This is a report on experimental work on development of a gasification process operating at near atmospheric pressures and using finely pulverized coal entrained in oxygen and steam. The gasifier was designed by The Babcock and Wilcox Co. in cooperation with engineers of the Bureau of Mines Morgantown station. The test work discussed in this report covers the first 34 tests made in the pilot plant in which a strongly coking Sewickley-bed coal, ground to either 70 or 90 percent through a 200-mesh screen, was used.

Jan 1, 1954

The XVIth International Conference on Coal Mine Safety Research was divided into eight half-day technical sessions. In accord with the established practice of these conferences, at each session, presentation of the papers was followed by a discussion period. Questions and comments submitted in writing to the session chairman were answered or discussed by the authors of the relevant papers or by their representatives. These discussions were tape-recorded in the original language of the speaker and subsequently translated into English when necessary. Questions to which no answer was available at the time and a few comments that exceeded the scope of the session have been omitted.

Jan 1, 1975

"INTRODUCTION While investigating prevention of sabotage and maintenance of production of essential war minerals, engineers of the Bureau of Mines visited more than 1,400 metal and nonmetallic mines, quarries, and open pits in all parts of the United States.The need for, uniform safety practices is indicated by the fact that during 1938-1940, inclusive, the Western Safety Conference, under the sponsorship of the California Department of Industrial Relations, undertook the prepara¬tion of a set of standard safety regulations for the 15 participating political subdivisions. The membership of these political subdivisions is comprised of representation from Alaska, Arizona, British Columbia, California, Colorado, Hawaii, Idaho, Lower California, Montana, Nevada, New Mexico, Oregon, Utah, Washington, and Wyoming, For the guidance of its own engineers; the Bureau of Nines found it necessary to prepare a set of safety practices that could be used uniformly throughout the United States. These safety practices were compiled from State mining regulations, mining company safety rules, and the experience of Bureau of Mines engineers for more than 3 decades, and represent the best safety practices of the Nation's' mineral industry.The purpose of this publication is to make safety practices available for the non-coal branches of the mineral industry, with the hope that they may assist in reducing accident occurrence. The Bureau will welcome questions and suggestions regarding these practices in order that changes may be made as necessary.Where the adoption of any practice would not materially increase the safety of employees or would work undue hardship on the operator, the Bureau does not recommend such adoption."

Sep 1, 1946

By W. M. Merritts

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining, This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes, In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased.

Jan 1, 1962