Search Documents

By Alan Mayton, Bertrand Valero, Farid Amirouche

Handling of heavy vehicles such as tractors, trucks and buses require a large roll stiffness which causes large high accelerations at the seat level during impacts. To provide comfort and minimize the energy transfer from the chassis and the seat a pneumatic active seat suspension is proposed. An active seat suspension design and control algorithm under development at the University of Illinois at Chicago, UIC, is being developed and tested. Preliminary results are presented in this paper. The design of a passive suspension typically consists of optimizing the value of two parameters: the stiffness and the damping of the suspension. The general dynamic performance of the suspension is limited to the conditions under which these parameters were obtained. A change in the input conditions might lead to poor suspension and an amplification of the vibration transmitted to the body. The focus of this paper is a robust, semi-active suspension system with a variable controlled damping and using the body response an index measure to minimize the acceleration at the interface of the seat and operator. A summary of existing suspensions, such as MR and ER fluids, and spring loaded and dual valve shock absorbent will be discussed to highlight the need of a semi-active pneumatic suspension system design. Methods A model of the proposed suspension was developed in MATLB (Simulink) and different control strategies for the valve position in relation to the cylinder pressure tested. The effects of stiffening and softening resulting from pressure changes in the cylinder were examined. The vertical accelerations of the seat was computed for different control strategies and configurations of the suspension and compared to the response of a passive seat suspension. A lump -mass model was created to represent the human body including the head, the upper, middle and lower torso as well as the legs. The connective forces between body segments were modeled through modal analysis techniques from previous experiments at the Vehicle Technology Laboratory. ISO standards and absorbed power were used to evaluate the different configuration of the seat suspension system in relation to the dynamic response of the operator. Results Initial results of the semi-active suspension system show a significant reduction in the RMS value of the acceleration of the seat. A reduction of the total absorbed power by the operator is expected to provide an insight into the control strategies adapted in the active suspension.

Jan 6, 2006

By Fredrick L. Johnson

The Jerry Peak, Jerry Peak West, and Boulder Creep: Wilderness Study Areas contain no identified mineral resources. Two workings, a 20-ft-long adit and a pit, were found in Paleozoic, brecciated, limonitic jasperoid in the east part of the Jerry Peak Wilderness Study Area (WSA), but no significant metallic mineral values were noted. Lenses and pods of quartz containing copper minerals occur in Paleozoic sedimentary rocks 1/2 mi north of the Jerry Peak West WSA. Similar rocks crop out along Pine Creep: in that study area but no copper-bearing quartz lenses were found.

Jan 1, 1984

By Robert H. Mattes

The Lake Lynn Laboratory is a multipurpose mining research laboratory operated by the Bureau of Mines and located in Fairchance, Pa, It consists of both surface and underground facilities. The initial focus of the facility, scheduled for full operation in fall 1982, will be on the problems of fires and explosions in mines. The initial experimental explosion was fired on March 3, 1982. The intent of this document is to provide the reader with detailed information on the physical capabilities of the Lake Lynn Laboratory. Subsequent publications will focus on the capabilities of Lake Lynn as compared with those of other similar facilities worldwide, and a comparison of initial explosion test results realized at Lake Lynn and comparable results from the Bruceton Experimental Mines.

Jan 1, 1983

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1985. Shipments of processed tripoli increased slightly in quantity but decreased 6% in value, Production of garnet, an abundant iron-aluminum silicate, increased 24% in quantity and 20% in value. There was an 11% increase in the quantity and a 7% increase in the value of refined garnet shipped when compared with 1984 shipments, a new record high. Production of crude special silica stone decreased 10% in quantity and 14% in value, and shipments of finished special silica stone products decreased 85% in quantity and 68% in value. Both the quantity and value of special silica stone finished products sold or used were the lowest since 1981. Production of emery, an impure aluminum oxide, decreased 56% in quantity and 61 % in value of product mined and shipped. [ ]

Jan 1, 1987

By Gregory P. Cole, Peter G. Kovalchika, Rudy J. Matetic, Adam K. Smith

Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/nonmetal miners had a hearing impairment by age 501. Mine workers are exposed to additional noise levels underground due to the reflection of machine generated noise that would otherwise dissipate in an above ground setting. Determining the sound absorption coefficients is essential in modeling the sound field in an underground mining environment. Sound absorption is a measure of the amount of acoustic energy that strikes a surface and is absorbed, rather than reflected. The acoustic environment that mining machines operate in is a critical factor affecting the sound pressure level exposure for mining machine operators. Impedance tube testing is an inappropriate method for determining underground absorption coefficients due to the brittle composition of some of the materials such as coal and slate. Classic absorption coefficient estimation using T60 measurements will not work well in an underground environment because the theory assumes: a finite room, a diffuse field, and relatively uniform absorption. None of these assumptions are true in an open-ended mine entry. This paper will present a method using a ray-tracing technique to determine absorption coefficients for underground mines. Absorption coefficients are determined and presented for octave bands from 63 Hz to 8 kHz. The absorption coefficients will be essential for determining and predicting potential overexposure to machine operators in different mine environments.

By W. W. Weller

Thermodynamic values for scandium and its compounds are very sparse. This is evident upon examination of any of the commonly used compilations of thermodynamic data. For example, National Bureau of Standards Circular 5004 lists only four heat of formation values, two free energy of formation values, and four heat-capacity values for scandium compounds. The entropy of crystalline scandium is one of the most fundamental values that has been lacking. This Bureau of Mines paper reports heat-capacity data for scandium metal in the temperature range from 50° to 298° K., together with the entropy value at 298.15° K. derived from these data through application of the third law of thermodynamics.

Jan 1, 1962

By J. E. Chilton

A technique for use in underground coal mines measures the response times of machine-mounted methane monitors. This technique uses a calibration cup to deliver gas to the sensor head to measure response times. For comparison, in the current study, response times were measured by placing methane sensor heads in a specially designed test box where they were exposed to an atmosphere containing a constant concentration of methane. Response time readings measured in the test box were shorter than the readings obtained using the calibration cup. The response times measured in the test box were comparable for sensors from three different manufacturers. The effects of dust cap and flame arrestor design on response times were also evaluated using the test box.

By Thomas O. Glover

Cameroon's mineral industry continued to be dominated by crude petroleum. The country's economic development depended on the production and export of crude oil. Oil output was estimated to be 56 million barrels in 1984 compared with 47 million barrels in 1983 and 39 million barrels in 1982. The country's only refinery processed approximately 16,000 barrels per day of crude oil in 1984, operating at slightly over 50% capacity. This volume, however, supplied the domestic need for motor fuel and heating oils. Cameroon's economy continued to expand despite problems and setbacks stemming from the attempted coup of April 6, 1984. Gross domestic product (GDP) growth in 1984 was 6.5%, the same rate as in 1983. Offshore crude petroleum production was the chief factor in the sustained economic growth. The country also maintained a relatively strong balance-of-payments position through oil exports. Investment, ranging up to 25% of the GDP, greatly contributed to sustained growth. The oil sector contributed approximately 14% to Cameroon's GDP in both 1983 and 1984.

Jan 1, 1986

By L. C. IlsLey

"There is an old saying that ""It is too late to lock the stable after the horse is stolen"". Is not this just what is being done by many mine operators today when it comes to buying safe electrical equipment for gaseous and dusty coal mines?The ""open type"" of electrical equipment or even the ""half safe"" type represents the unlocked stable. After the mine disaster, and after men have lost their lives, the lock is put on - that is, safer equipment is installed.For example, an open type of electric coal drill was used in a gaseous mine in West Virginia, This was the probable cause of the death of 27 men. A half safe type of electric coal-cutting machine was used in a gaseous mine in Pennsylvania. This was likely the cause of the death of 36 men. An unapproved, unsafe type of flame safety lamp was used in a gaseous and dusty mine in Utah. This was the all¬eged cause of the death of 171 men. All three disasters happened within the last six months, and seem to have been avoidable if proper equipment had been used.It is understood that more rigid requirements will be enforced in West Virginia. The committee of State mine inspectors made definite recommendation for im¬proving the conditions in the given mine in Pennsylvania. The Industrial Commission of Utah have already issued new orders which will remedy the use of unsafe lamps in that State.These acts and recommendation are all good and will help prevent accidents in those States in the future. Is it not a pity that such recommendations and order were not made a little earlier before the tell of life had been exacted? Is it not a pity that other States will not take these lessons to heart and safeguard their mines before and not after disasters take place?Electric current can cause accidents in five general ways as follows: (1) By shock to persons; (2) by igniting powder; (3) by igniting gas; (4) by igniting coal dust; and (5) by setting fire to inflammable material such as timber and coal. A great many accidents from these causes are preventable if proper care is taken. Most of the accidents caused by sparks and flashes from electrical apparatus would not take place if approved electrical equipment was used. By approved equipment, the writer means equipment that has been tested and formally approved by the Bureau of Mines. So far as known, up to the present time, no disasters have been caused by sparks or flashes from equipment having the Bureau's approval."

Jul 1, 1924

By John J. Sammarco

Abstract- Emergency shutdown systems (ESDs) for mining machinery provide critical functions to safeguard miners. Traditionally, ESDs were realized with simple hardwired circuits; today, there is a growing trend to use programmable electronic technology such as programmable logic controllers (PLCs). This paper describes an analytical study to quantify the safety integrity of a PLC-based ESD and a hardwired ESD. The safety integrity level of each design approach was determined by quantifying the average probability of failure on demand (PFDavg) as described by the recommendations for programmable electronic mining systems published by NIOSH and the IEC 61508 international standard. The safety analyses addressed system architecture, hardware failure probability, proof test interval, diagnostic coverage, and human error probability. The results indicated that a same level of safety, safety integrity level 3 (SIL 3), could be attained when evaluating random hardware failures. Neither approach could attain SIL 3 if manual activation was used. Human error was the limiting factor where, using human reliability analysis, PFDavg < 1 x 10-1; thus, the ESD does not meet SIL 1. It is apparent that automatic verses human¬activation of the ESD is a very important safety consideration. Manually actuated ESDs can only achieve SIL 1 regardless of the technology; therefore, additional independent safety layers of protection are needed to exceed SIL 1. Secondly, it is apparent that the technology choice is very important. The PLC-based ESD was much simpler to design and to validate safety1.

Jan 1, 2007

By C. Ozgen Karacan, William P. Diamond

In This Chapter [Measuring the gas content of coal Predicting gas emissions based on geologic and coal reservoir property data Determining the gas storage capacity of coalbeds and other gas-bearing strata Methane drainage borehole monitoring to forecast the remaining gas-in-place and the influence on mine emissions Forecasting gas emissions during mining as a function of mining parameters and Gas emission prediction based on numerical simulation] This chapter provides guidelines for determining the gas content of coalbeds, estimating the gas-in-place, and predicting gas flow and emissions before and during coal mining operations. The techniques are discussed briefly in the following sections. However, detailed information on the techniques is provided in the cited references. INTRODUCTION Coalbed methane, if not properly controlled in the underground mine environment, is a safety concern due to the potential risk for an explosion. This is a particular problem during longwall mining, where the high rate and volume of coal extraction can result in the release of large amounts of methane from the mined coalbed and other adjacent gas-bearing strata. The variability and potential hazards of these sometimes unexpectedly high gas flows provide the impetus to develop methods to predict methane emissions into the underground workplace. A forecast of the volume of gas that might be released during coal mining is helpful for designing ventilation systems and for implementing optimum methane drainage strategies to help mitigate expected gas emission problems. A complete assessment of the need for methane drainage prior to mine development generally requires both an empirical and a theoretical approach. If there are active mines in the general area with similar geologic conditions and coal characteristics, a review of gas problems in those mines provides an initial insight into the level of gas emissions to be expected at a new location. In addition, relatively simple methods exist to determine the in situ gas content (volume of gas per unit weight of coal) of the coalbeds in a particular mining area, as well as the gas-in-place (volume of gas in the coalbed(s) within a defined geographic area).

Jan 6, 2006

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By Danny Riley, Brian Curry, Sandya Govindaraju, James Bain

Hand arm vibration syndrome (HAVS) affects industrial workers exposed to long term hand-transmitted vibration from powered-tools. Peripheral neuropathy is a major component of the symptom complex of HAVS. Long term exposure to vibration causes myelin damage in peripheral nerves and reduces nerve conduction velocities in rats1. This study addresses the effects of acute vibration at constant acceleration of 49 m/s2 on myelinated fibers in peripheral nerves in Sprague-Dawley male rats using the ‘rat-tail vibration model,’ which simulates hand-transmitted vibration2. Methods Male Sprague-Dawley rats (~300 g) were assigned to vibration groups: 1 hr continuous vibration at 60 Hz; 4 hr continuous exposure at frequencies of 30, 60, 120 or 800 Hz; immediate and 24 hr following a 4-hr cumulative exposure of continuous and intermittent vibration at 60 Hz. Unanesthetized rats were restrained in cages on a nonvibrating platform with their tails placed on a vibrating stage accelerated by a B&K motor type 4809 and vibrated. Intermittent vibration was delivered in bouts of 10 min vibration alternating with 5 min rest periods repeated over 6 hr. Sham controls were restrained without vibration. After vibration exposure, the rats were anaesthetized, and the ventral nerve trunks from the proximal tail segment 7 were fixed in glutaraldehyde, embedded in epon-araldite and sectioned at 0.5 µm thickness and stained with toludine-blue for morphological quantitative analysis. The total number of myelinated axons in each cross-section of the nerve was counted using the Image J software. Myelin damage was identified by focal increase in area and intensity of toludine-blue staining and unraveling of the myelin sheath. Statistical analysis for comparing sham and the different vibration groups was done using Dunnett’s test. Animal treatment and all surgical procedures were approved by the institutional review board and compiled with the Laboratory Animal Welfare Act. Results The rats tolerated continuous vibration very well and exhibited no behavioral signs of stress. When exposed to intermittent vibration, there was increased vocalization, a startle reflex at the beginning of each bout of vibration, deposition of porphyrin around the eyes and transient hypersensitivity to touch.

Jan 6, 2006

By D. F. Smith

The thermodynamic data presented in the literature for zirconium compounds are incomplete. Among the compounds for which adequate data are Zacking are zirconium fluoride and sulfate. This paper reports experimental heat-content values determined by the Bureau of Mines for these two zirconium salts throughout the temperature range of 273° to 1,200° K. No crystalline transformations were found in the two compounds investigated, and neither of the compounds melted over the temperature range studied. MATERIALS TESTED The Oak Ridge National Laboratories, Oak Ridge, Tenn., supplied the two zirconium salts used in this investigation. The zirconium fluoride was high- purity reactor grade material. The zirconium sulfate contained between 0.01 and 0.10 percent hafnium and calcium, and other elements in concentrations below 0.01 percent, A spectrographic analysis of the two compounds is given in table 1. Before use the compounds were dried at 400° C. for several hours to removed adsorbed moisture.

Jan 1, 1962

By S. M. Runke

"During the past three years the Bureau of Mines has carried on an extensive research program at the Rolla Laboratory for the beneficiation of low-grade Arkansas baixites by ore dressing methods. As a result of this study a 50-ton pilot mill was designed and constructed at Bauxite, Arkansas, by the Bureau to continue the investigation on a semi-commercial scale. The built both to reduce the experimental work to practice and to obtain operating data that cannot be determined by laboratory or small scaleTen samples of bauxitic material were mined and stockpiled at the plant site to ensure an ample supply of material for milling in the pilot plant. These samples were obtained from various bauxite deposits in Saline and Pulaski Counties, Arkansas. The deposits were selected as typical of a wide range of bauxitic material which would necessitate treatment under different conditions and by various concentration methods. All of the samples contained a higher silica content than permissible in Bayer-grade bauxite and several contained so much iron oxide that the available alumina content of the ore was mate¬rially lowered. From data obtained by milling operations on these ten samples, milling characterietics of most of the ores in the district should be predictable. This paper summarizes the results obtained in the laboratory testing of representative samples of each stock pile, and the results of small scale continuous testing of the composite sample of the ten stock piles in the gravity-flotation pilot plant at the Rolla Laboratory."

Aug 1, 1946

By Gary J. Cwick

Mineral resources of the Rice Valley Wilderness Study Area (WSA), in the Mojave Desert of southeastern California, were investigated by the U.S. Bureau of Mines and U.S. Geological Survey during 1980. The study consisted of an examination of mines, prospects, and mineralized areas by the Bureau: of Mines and geological, geochemical, and geophysical investigations by the Geological Survey. Little indicated potential for the presence of mineral resources exists in the valley floor segment of the study area. The Big Maria Mountains section of the study area has some potential for mineral resource development. Decorative building stone from both bedded quartzite deposits and weathered limestone surface rubble (driftwood stone) has been produced from the Big Maria Mountains segment of the study area. Total production is unrecorded but probably small. A 700,000 ton (640,000 t) quartzite resource was inferred and 4,500 tons (4,100 t) of driftwood stone within the study area was estimated. A relatively pure limestone deposit inside the study area contains an inferred resource of 14 million tons (13 million t). One prospect suggests a potential for the presence of manganese resources although none were estimated. The likelihood of discovering oil, gas, coal, uranium or geothermal energy is low; potential sources are not known to exist.

Jan 1, 1982

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By R. F. Zaffarano

Reservoir oil in the Greater Aneth area, Utah, part of the Paradox basin, was studied to detect variation in oil characteristics within the reservoir and to determine its relation to age of accumulation and fluid equilibrium. At least three subsurface oil samples were obtained from each of the four largest of five field divisions comprising a producing area of 45,000 acres. Height of the oil column in the Pennsylvanian Desert Creek zone is about 230 ft. In general, the oil characteristics were found to be uniform across the area, and averages were developed for use in engineering applications. Average saturation pressure was 1,780 psia; the oil was undersaturated at the initial reservoir pressure, 2,200 psia. Variation in saturation pressure shows a lack of complete fluid equilibrium and continuing diffusion of solution gas from the main body of the reservoir to two extensions linked by narrow arms. By assuming early accumulation, the time involved in this diffusion process was calculated to be about the same as the age of the reservoir formation. Cause of the concentration of gas in the main body is attributed to differential entrapment during accumulation of oil and gas from an exterior source.

Jan 1, 1963

By J. E. Urosek, K. L. Cashdollar, D. A. Beiter, G. J. Shemon

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on mine ventilation stoppings at the NIOSH Lake Lynn Experimental Mine (LLEM). After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to mitigate or eliminate future occurrences. As part of these post-explosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, are documented as evidence of the strength and the direction of the explosion forces. The LLEM data showed that a total pressure of 52 kPa (7.6 psi) destroyed the solid concrete block stopping, ~36 kPa (~5.2 psi) destroyed the hollow-core concrete block stopping, and 9 kPa (1.3 psi) destroyed the steel panel stopping. These results will assist investigators in determining the explosion forces that destroy or damage stoppings during actual coal mine explosions.

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world&apos;s largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999