Search Documents

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) The system design of hydrostatic drives for mine hoists, usually of special nature, is considered along with oil hydraulic component selection suitable for the application; (b) The criteria for head frames of steel and/or concrete are developed with full consideration of all operating and environmental conditions.

Jan 1, 1988

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and operating costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per cfm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured under-ground. This volume constitutes Volume II of the report and contains the outputs of the computer simulation runs.

Jan 1, 1983

By Andrew Cecala

The Bureau of Mines performed tests to compare the effectiveness of steam and of water sprays to reduce respirable dust levels at mineral processing plants. By applying 0.22 wt pct water vapor as steam to product material, a 64-pct respirable dust reduction was recorded. By applying the same amount of moisture with water sprays, only a 25-pct dust reduction was recorded. By increasing the moisture content up to0.5 pct using water sprays, the dust reduction was increased to 55 pet, which was still less than the dust reduction achieved by adding less than half that amount of water in the form of steam.

Jan 1, 1985

By Andrew B. Cecala

The Bureau of Mines conducted a brief laboratory study on the 10-mm diam Dorr-Oliver nylon cyclone to investigate (1) whether high wind speed (>300 ft/min), or sampler inlet orientation with respect to wind direction, can introduce errors when sampling respirable dust, and (2) whether any such errors can be reduced by using an inlet shield. Being preliminary in nature, the study was not structured to produce definitive results, but rather to discern likely trends and to indicate whether or not a more in-depth study of the problem is warranted. Photometric mass sensing measurements suggested that as the wind velocity increased, the cyclone sampling directly into the high-velocity airstream tended to oversample, relative to the cyclone sampling in a low-velocity airstream. Orientation of the sampler introduced measurable differences in sampling efficiency at higher wind velocities. A shield placed around the cyclone diminished the effects of wind velocity and sampler orientation on sampler performance. Results of this work offer sufficient evidence to substantiate the need for a more in-depth study.

Jan 1, 1983

By J. B. Zadra

Tungsten, a comparatively new metal, is one of the important strategic war materials. In peacetime, tungsten is widely used as a filament in elec¬tric lamps and electronic tubes and is a vital constituent of some of the most important industrial alloys. High-speed tool steel containing tungsten and stellite alloys containing cobalt, chromium, and tungsten are extremely hard and resistant to corrosion. These alloys and the tungsten carbides are unequaled as cutting tools and in other wear-resistant applications. They play a prominent role in the present era of mass production. Alloys containing tungsten resist oxidation at high temperatures and have been key alloys in the development of modern aircraft. The adaptability of tungsten to new uses is expanding, particularly in the high-temperature range. Domestic production of tungsten has come from a large number of deposits in 17 of the 49 States; but, of the total domestic output from 1900 to 1956, more than 80 percent was produced from mines in North Carolina, California, Colorado, and Nevada. The average tenor of the mined ore was less than 1 percent tungsten trioxide (W03).

Jan 1, 1959

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

By Hillary W. St. Clair

This is an initial progress report on a theoretical study of the iron blast furnace. The purpose is to develop a thermochemical model that will simulate mathematically a real furnace. An analysis is made of the behavior of a hypothetical furnace, operating adiabatically on pure ferric oxide, graphitic carbon, and dry air. Relationships are derived for carbon consumption, gas composition, and reaction temperature for a furnace operating at steady state, and in which the smelting rate is slow enough for the gas and solids to approach thermal and chemical equilibrium. Analyses are made for two contrasting types of gas flow: (1) Nonturbulent flow, having no vertical mixing; and (2) turbulent flow, having perfect mixing during each step of the process. It is shown that some vertical mixing is essential for complete reduction of ferrous oxide and that the extent of vertical mixing is one of the critical factors in the behavior of the furnace, This analysis indicates that the thermochemical relationships in a blast furnace can probably be best simulated by a finite series of gas-solid reactors through which gas and solids flow countercurrently and in which the temperature and composition of gases and solids are assumed to be uniform. Any degree of vertical mixing can be approximated by the proper choice of the number of reactors.

Jan 1, 1963

By E. D. Gardner

This is one of a series of papers describing mining and related subjects affecting mining in western mining districts and mineralized areas. The parts of this paper pertaining to current production, mining and milling methods and practices, and general conditions affecting mining were collected principally during a field survey made in May 1935. Some original data obtained on previous visits to the area are also included. The history, geological background, and past production of the mines and district are largely abstracted from previous publications, for which due credit is given later in the test. The principal districts in the Black Mountains are the Oatman or San Francisco and the Union Pass or Katherine. This range contains the principal producing mines of the State, in which gold is the only important metal. Although the total production of gold is relatively small as compared to other districts where the precious metals are obtained as a by-product in copper min¬ing, the area is one of considerable economic importance to the State.

Jan 1, 1936

By Ivor Hawkes

This report describes the results of a study to evaluate new design concepts for percussive rock drills that will result in quieter machines. It is shown that by incorporating such features as an efficient muffler, a plenum chamber integral with the machine body, and shroud tubes around the drill rods, etc., noise levels are reduced from about 114 dBA to about 95 dBA with very little change in drilling performance.

Jan 1, 1977

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization; and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed 'and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number S0241073 by Fenix & Scisson, Inc. to the Denver Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974

By C. H. Manney

This report deals with the feasibility of the use of vocoders as an integral part of a mine electromagnetic voice communication system. Limitations imposed by the nature of the transmission path, background noise and equipment are examined. Some properties of vocoders and apparent advantages of the use of vocoders in a mine communication are discussed. The conclusion is reached that the man-made noise level will ultimately determine the workability of such a system.

Jan 1, 1972

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

By John G. Palmer

Continued development of an especially impregnated silica gel capable of reversible chemical detection of carbon monoxide (CO) was reported. The affects of changes in mine-related ambient conditions on the detection catalyst's response were explored. Temperature, humidity, and several interfering gases were found to affect the detection catalyst. The interferents include hydrogen sulfide, nitrogen dioxide, acetylene (and methylacetylene), and ammonia. High humidity decreased the detection catalyst's sensitivity to carbon monoxide for some formulations. Increasing temperature generally decreased the reaction time of the detection catalyst with carbon monoxide. Badges and carriers for the visual presentation of the detection catalyst were constructed. Several variations of these devices included provisions for absorbants and filtering agents which help protect the detection catalyst from gaseous interferents. A variety of catalyst support agents were tested in an effort to find the most suitable. Included were alumina, magnesium oxide, magnesium silicate, and several forms of silica gel. In addi tion to free-flowing forms of these sorbents, thin layer chromatography plates coated with cellulose, alumina, and silica gel and newly developed PTFE entrained silica gels were examined. A limited physical, chemical, and mechanistic characterization of the detection catalyst and the materials used to prepare it has been carried out. Metal component ratio studies, spectral, analytical, pH, and rate measurements were done.

Jan 1, 1982

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

By Lawrence K. Barker

Crude shale oil produced by underground retorting of Green River Formation oil shale was hydrogasified over a cobalt-molybdate-on-alumina catalyst at operating temperatures ranging from 800° to 1,300° F, pressures of 500, 1,000, and 1,500 psig, and a liquid hourly space velocity of 1.02 volumes of oil per volume of catalyst per hour (Vo/Vc/hr). At a temperature of 1,300° F and pressure of 1,500 psig, 94 weight-percent of the liquid feed was converted to gas containing 72 volume-percent methane. With two reactors in series at a temperature of 1,170° F in reactor 1 and 1,260° F in reactor 2 and a pressure of 1,500 psig, 97 weight-percent of the liquid feed was converted to gas with a methane content of 75 volume-percent. Liquefied petroleum gas (LPG) was hydrogasified at operating temperatures ranging from 500° to 1,400° F at a pressure of 500 psig over a cobalt-molybdate-on-alumina catalyst. Similar experiments were made with an empty tubular reactor. The data indicate that gasification reactions in the presence of a cobalt-molybdate catalyst change from predominantly a catalytic (carbonium ion) reaction to predominantly a thermal (free radical) reaction at temperatures greater than 1,100° F. The data also indicate that a reaction temperature of 1,350° F is necessary at the space velocities used in this investigation to make a synthetic natural gas (methane content of 90 volume-percent) from in situ crude shale oil.

Jan 1, 1975

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982

By F. A. Penning

This report describes the development of skip and guide desings for vertical shafts in deep vein mines. Skip and guide systems for bottom dump skips are identified as being used in current practice. Mine visits were made to obtain current information on the needs and problems of operating mines. Methods of structural and mechanical analysis of skip bodies and bails are outlined. A dynamic computer model was written to find the dynamic interaction between skips and guides for guides with geometric misalinements. A materials evaluation section identifies currentavailable and applicable materials that can be used effectively for new skip construction. Guide materials are also presented. Analysis includes the economies resulting from streamlined buntons and from low skip payload ratios. Selection of materials is based on strength, abra¬sion and corrosion resistance. Design requirements related to the shaft environment are presented. Consideration for the selection of guides and buntons is also given. Conceptual design includes the concept of cylindrical skips, center-seeking guide rollers, and asymmetric bail design to decrease dynamic interaction. An outline for field tests is presented. Future research areas are: testing, guide geometry measure¬ment, advanced suspension, dynamics, and structural configurations.

Jan 1, 1977

By L. M. Irwin

This Bureau of Mines investigation relates the physical properties of copper reverberatory furnace slags to changes in composition, The smelting of upper Michigan copper ore presents some problems that probably differ from those of other copper smelting areas. The study of these problems has, however, provided important data regarding slags in general and therefore will be of value to other operations as well. Conclusions reached from this study were: (1) Slag fluidity and refractive indices varied directly with the iron content and inversely with silica, lime, and alumina, and (2) there was no apparent correlation between slag fluidity and its copper content.

Jan 1, 1962