Search Documents

By Donald R. Corson

The effects of adding varying amounts of type I portland cement to hydraulic backfill are described. Six different fill materials, each with three cement contents, were tested to determine which fill properties have the most significant effect on cemented strength. Two strength prediction equations, based on the physical and mineralogical properties of the fills, were formulated, and these accounted for 96 and 99 percent of the variability of the data. Results of both unconfined compression and triaxial tests of cemented fills are given, and the effects of moist curing and fill densification on the 7-day strength are discussed. Permeability test data are given, and the decreased permeability due to cement content and curing time is shown graphically. A discussion of the limited evaluation of other potential stabilization additives (expansive cement, fly ash, sodium silicate, gypsum, and asphalt) is included in an appendix.

Jan 1, 1970

By G. F. Kuncir

The analysis summarized herein evaluates the Bureau of Mines Program for Advancing Mining Technology Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings, environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

"To prevent the propagation of mine explosions, the Bureau of Mines recommends:1. That all coal and lignite mines, except anthracite mines shall be rock dusted.2. That rock dust shall be distributed upon top, bottom, and sides of all underground openings of every description, to within. at least 4o feet of all working faces and the areas not rock dusted shall be kept wet.3. That the rock dust shall be maintained in, such quantity that the incombustible material in representative samples of dust collected shall not be less than 65 percent. Where methane gas is present in the ventilating current, the minimum percentage of incombustible matter in the mine dust shall be increased 1 percent for each 0.1 percent of methane.4. That when the rock dust in any area becomes caked so thatit cannot be dispersed readily as a cloud in the air, that part of the mine shall be redusted immediately.5. That the dust to be used shall not contain more than 5 percent of combustible matter nor. more than 25 percent of quartz or free silica; all of the dust shall pass through a sieve having 20 meshes per linear inch and 60 percent or more shall pass through a sieve having 200 meshes per linear inch; the dust shall not absorb moisture from the air to such an extent as to cake and destroy its effectiveness as a dry dust.6. That rock-dust barriers shall not be regarded as a substitute for generalized rock dusting.Research and experience have shown that maintenance of an adequate percentage of rock dust in all underground openings, whether gassy or not, of bituminous and subbituminous coal and lignite mines (anthracite dust does not propagate explosions) is the best means of preventing coal dust explosions. In rare instances where all fine coal particles on the floor, ribs, roof, and timbers are in a muddy condition continuously rock dusting is unnecessary.The term ""underground openings"" refers to all unsealed openings whether they contain track or not, and includes rooms, entries, crosscuts, breakthroughs, rock tunnels, slopes, haulageways, airways, and travelingways. The sealing of unused or abandoned parts of a mine in accordance with Mine Safety Board Decision avoids the necessity of rock-dusting the sealed-off openings.The kind of rock dust to be used should have the approval of the State Mine Inspection Service. Pure limestone or pare dolomite produces the best rock dust, as these dusts have low silica content, little tendency to cake, and a light color that aids illumination. To reduce tendency to cake it is preferable that not more than 75 percent of the dust pass the 200-mesh sieve. All sieve sizes are those of the Tyler screen scale. If the mine personnel is repeatedly exposed to breathing high concentrations of the dust, the percentage of free and combined silica should be as low as possible, preferably less than 5 percent. Persons engaged in the application of rock dust should wear approved dust respirators as listed in Bureau of Mines Information Circular 7030 or revisions thereof."

Mar 1, 1940

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By R. H. Thompson

Preliminary safe distances for blasting wiring from typical electromagnetic sources are presented. The distances are for underground coal mines and electromagnetic sources in the frequency range below 10 MHz. The distances are based on measurements performed at 3 locations in each of 3 coal mines. The measurement apparatus, measurement procedure, measurement results and the rationale used in the calculation of the safe distances are all described. The safe distances presented are dependent on the measurement results and their interpretation. More measurements are clearly necessary to establish the validity of the suggested distances.

Jan 1, 1985

By J. R. McVey

A 10-channel automatic data acquisition system has been designed and environmentally packaged for use with underground strain-gage applications and associated instruments. The system uses commercially available components and is assembled in two plastic enclosures. Environmental control is provided through a specially designed (compressed-air) air-conditioning system and water-resistant cabling. Accuracies of 0.01 pct and resolution of 1 µV have been obtained in underground tests.

Jan 1, 1973

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

By R. S. Dean

"INTRODUCTION The idea of direct steel is by no means new. Although the work of Bessemer and Siemens provided simple and effective moans for converting pig iron into steel and established the ""blast-furnace route"" as the almost universal method of producing steel, metallurgists have not ceased to dream of direct steel. By direct steel is meant any process by which iron oxide in ore is reduced to Iron of the same or greater purity than the final steel or wrought iron. That is, carbon or alloying elements would be added as needed, not reduced in unwanted quantities into the iron and then removed more or completely by refining (Bessemer or open hearth) only to be readded in desired quantities.In general, direct-steel processes are ""sponge-iron"" processes, because reducing iron oxide without simultaneously alloying the iron with carbon, phcophorus, sulfur, and silicon present in ore and fuel succeeds only if the temperature is below the melting point of the iron. Such solid iron formed by reduction of iron oxide at relatively low temperature is sponge iron, which is butlery and porous. When the reduction proceeds at the higher temperature at which the particles of metal can weld together or finally even melt to yield pellets or balls that do not have the porosity and low-density characteristic of sponge iron, the product might preferably be called simply ""direct iron."""

Jan 1, 1945

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By J. I. Paige

As part of a continuing effort to develop technology that maximizes mineral and metal recovery from domestic resources, the Bureau of Mines investigated a method to totally utilize copper converter slags without recycling them back through the matte smelting furnace. The research was directed toward (1) recovering the contained copper in converting slags by producing a recyclable copper-iron matte, (2) carbothermically reducing the slags to recover the iron, and (3) producing slag wool from the depleted slags. This report deals with the reduction of three industrial converting slags, containing 2.0 to 7.3 wt-pct Cu, in an 800-kVA electric arc furnace to produce a recyclable copper-iron matte. The addition of sufficient iron pyrite to provide 29 to 113 pct of the stoichiometric sulfur (based on producing 40-pct-Cu matte) produced a recyclable matte (36 to 61 pct Cu) at an energy consumption of 520 to 700 kWh per ton of solid material charged. The expected energy saving for treating molten slag in an electric furnace (5-to 9-MVA range) is about 400 kWh per ton of molten slag treated.

Jan 1, 1982

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By Nutter R. S.

A methodology has been developed for qualitative safety hazard evaluation and quantitative reliability analysis of mine monitoring and control systems. Detailed application of these techniques were made to two commercial monitor/control systems and to a West Virginia University distributed microprocessor-based system. A controlled environmental test was conducted on a set of one of the commercial system's outstations. A software reliability evaluation methodology was also developed and applied.

Jan 1, 1982

A compilation of papers presented at the Third WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 4-6, 1976. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1976

By B. W. Gandrud

[This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests mode by the Bureau of Fines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers. The Klandyke mine, operated by the Blocton Mining Co., is about 1 mile eat of Vest Blocton, Bibb County, Ala., floor the southwestern, extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the, washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/ one on the tabling of fine coal from the Thompson and Woodstock beds5/, and the third a washability study of the Henry Ellen bed at Acmar6/.]

Jan 1, 1939

By E. G. King

The literature contains little thermodynamic information regarding inter-oxidic compounds of the ferroalloy elements and, as a result, thermodynamic considerations of extractive and utilization processes involving these elements have been hampered. As part of a Bureau of Mines program to improve this situation, this paper reports the heats of formation of three calcium vanadates and two magnesium vanadates. There were no previous similar data for any of these compounds. The experimental method was hydrochloric acid solution calorimetry, using calorimetric reaction schemes involving the vanadates and their component oxides. The results were expressed as heats of formation from the component oxides and from the elements. Corresponding free energy of formation values were calculated. The data show that the calcium and magnesium vanadates are stable with respect to all possible decompositions in which vanadium remains pentavalent. This conclusion is similar to the one drawn by Koehler6 for three sodium vanadates.

Jan 1, 1962

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgical and chemical methods for extracting copper from sulfide ores under conditions that provide for control of gaseous and solid emissions. Under this program, a new electrothermic reduction process was developed to produce blister copper after collecting essentially all of the sulfur by a single-unit operation. The process feasibility was indicated by a laboratory-scale investigation that demonstrated chalcopyrite concentrate can be roasted to less than 1 percent sulfur and that the resulting calcine can be reduced with carbon to blister copper by a cyclic process in a single arc-smelting furnace. Pilot-scale tests in an 800-kV-A electric-arc furnace demonstrated that 98.4 pct of the contained copper can be continuously recovered as metal by operating at bath temperatures between 1,350° and 1,375° C. Smelting rates of approximately 225 lb of blend ft2 of bath surface/hr resulted in power consumptions of approximately 520 kW-hr/ton of blend. The blister copper that was produced contained less than 0.1 pct iron while the precious metals reporting to the copper product and gangue material elimination were similar to those in a conventional smelting operation.

Jan 1, 1976