Search Documents

By K. L. Paciorek

The aim of the present study is to determine on a gram per gram basis the toxic products of the thermal oxidative degradations of selected compositions. Four families of materials were investigated under the subject contract namely polyvinyl chloride and neoprene compositions, rigid urethane foams I and woods. Three methods were employed to conduct the thermal oxidative degradations: a sealed system (quiescent environment) I a stagnation burner arrangement (dynamic environment) I and a flow-through apparatus (dynamic I but less severe than stagnation burner conditions). The majority of tests were conducted using the first two systems; only limited experiments were carried out employing the third decomposition procedure. All decomposition was done at temperatures of 370 -4000C I the higher temperature being used in the stagnation burner. It has to be stressed that the nature of the products and the relative product concentration are temperature dependent. Thermogravimetric and differential thermal analyses were performed to supplement and extend the above delineated studies and to explore the feasibility of using these analyses as a method for material differentiation.

Jan 1, 1973

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972

By Sidney Katell

This cost bibliography, covering the period from January through December 1960, is a continuation of the series which began with the publication of Information Circular 7516 in October 1949. It is also the second report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, came from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal. Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil.

Jan 1, 1961

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

By J. R. Thoenen

This circular is part 5 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cable-way excavators, and hydraulic monitors; part 3, hydraulic, clamshell, ladder, and dipper dredges; and part 4, haulage systems in general, with particular reference to locomotive and car, hoist and car, and remote-control systems. This circular discusses the use of motor trucks, conveyor belts, pumps end pipe lines, barges and towboats, and aerial trams. MOTOR-TRUCK HAULAGE During recent years motor trucks have gained considerable ground as a successful competitor of locomotive haulage for quarries and gravel pits. Often where trucks have displaced locomotives and cars the operators readily admit an increase in both labor and total haulage operating costs but point to some other advantage as offsetting the extra expense. In other instances haulage costs have beep reduced by the use of trucks. In still others operators, having replaced locomotive haul with trucks, have again returned to the earlier method. Obviously gasoline-driven motor trucks cannot successfully compete with other types of haulage under all conditions. The apparent' growth in the number of advocates of truck haulage, however, indicates that it has passed the experimental stage and become a permanent competitor to other tyres.

Jan 1, 1936

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 116 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257, 7267, 7273 and 7285. 1. GRAVITATIONAL METHODS 7380. Dryden, H. L. A reexamination of the Potsdam Absolute Determination of Gravity. Jour. Research Nat. Bureau of Standards, vol. 29, No. 5, 1942, pp. 303-314.

Jan 1, 1944

By G. K. Derby

Five different types of drilling systems were developed under the flexible drill program that was initiated by the Federal Bureau of Mines to protect roof bolter operators. The systems were designed for underground coal mines with seams as low as 30 inches, and with roof bolts longer than the height of the seam opening. Four of the developed systems were true flexible drills; the fifth was a remote-controlled, automatic rod changer concept. Only two of the five firms successfully completed testing requirements under the original contracts: BendixCorp.,4 with a true-flex drill; and Ingersoll-Rand Research, Inc., with the rod changer concept. The Bendix drill was rated best, and the Ingersoll-Rand drill was rated second. Because of the closeness of the ratings and the vast differences in the two development concepts, both systems had sufficient potential to justify further development funding for design updating and testing. Also, both systems warranted consideration for inclusion into other ongoing development projects under both safety and energy directed programs.

Jan 1, 1978

By Thomas M. Sweeney

This open-file map is a quick reference containing location, ownership, and general lithology information on 124 active or significant Nevada gold mines. The map includes all counties, significant towns, and major highways in Nevada to aid in mine location. Several geologic trends with which the mines are associated are also depicted. General ore genesis for each deposit, including sedimentary, volcanic, plutonic, and placer-hosted deposits, are also identified. Gold mines are also listed alphabetically, by mine name, on the map. Each entry includes the appropriate county, percent of company ownership, operating company, and the property status as of May 1992. For additional information, contact Thomas M. Sweeney, U.S. Bureau of Mines, Western Field Operations Center, 360 East Third Avenue, Spokane, WA 99202; telephone (509) 353-2700.

Jan 1, 1993

By F. Fraas, J. E. Conley

"The problem of recovering potash from the mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O), occurring in large quantities in the salt beds of Texas and New Mexico, has been under investigation at the Nonmetallic Minerals Experiment Station of the U. S. Bureau of Mines continuously since 1928. Most of the results previously obtained have been published in technical journals and in a series of Bureau of Mines Reports of Investigations.The experiments described in the present report were performed to ascertain whether a continuous countercurrent extraction of calcined polyhalite by hot water would yield satisfactory recoveries and concentrations of sium sulphate in the top liquor. Previous investigation by Storch 4 had shown that the rate of solution of uncalcined polyhalite was too slow to be of value in an industrial process, and Storch and Clarke 5 had demonstrated that calcination of the polyhalite greatly, accelerated the rate of solution in hot water, allowing most of the potassium sulphate to be readily extracted."

Sep 1, 1933

By Gary E. Sherman

This report presents a Bureau of Mines study on the cost of mine permitting and compliance with environmental regulations in Alaska. It discusses permitting requirements and procedures for placer and lode mines. Placer miners must comply with recently established (1988) water quality regulations and effluent treatment requirements. To estimate the impact differing treatment options (no recycle, 100% recycling, and flocculation) have on a placer mine's rate of return, three models (1,500, 1,000, and 500 yd3/d) were simulated. Rates of return for these models show a marked decrease as effluent treatment is increased. The incremental increase in operating cost from one treatment option to the next is relatively small; however the opportunity cost of lost production if' significant and accounts for the decreasing rate of return with increased effluent treatment. Lode mines face greater costs for permitting and compliance than similarly sized placer mines as a result of the impact of the operation. Direct permitting costs for lode mines range from 2 to 6% of total project cost, with 4% the most common figure cited by industry. Total costs for permitting and compliance are approximately double those for permitting. Indirect costs associated with compliance include mitigation, monitoring, and reclamation.

Jan 1, 1991

By John M. Gomes

The preparation of tungsten carbide by molten-salt electrolysis was investigated. Sodium tungstate in the electrolyte and carbon from the graphite anode were the source materials, Optimum results were obtained with an electrolyte consisting of 83 mole-percent sodium chloride and 5.7 mole-percent each of sodium tungstate, sodium metaborate, and sodium hydroxide; a temperature of 1,000° to 1,025° C; an anode current density of 37 amp/dm2 or less; and an initial cathode current density of 150 amp/dm2. The yield was approximately 0.45 g/amp hr. The electrolytic tungsten carbide product contained approximately 5.4 weight-percent combined carbon as compared to 6.1 weight-percent for pure tungsten carbide. Microhardness of the electrolytic tungsten carbide, determined with a 50-gram load, varied from 3,480 to 3,970 dph. The material was friable and could be ground in a laboratory ball mill to less than 400-mesh particle size.

Jan 1, 1969

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

Two coal seams were selected and the conceptual designs were based on the geological and physical conditions typical of these seams. As a result of the screening process presented below, the two coal seams selected were the Lower Kittanning Seam in central Cambria County, Pennsylvania and the Pittsburgh Seam in northwestern West Virginia and southwestern Pennsylvania. SELECTION PROCESS FIRST SCREENING OF LONGWALL OPERATIONS The list of longwall operations prepared in Phase I and included in the Phase I report, was used as the basis for a first screening. From this list it was determined which longwall operations were not in the Appalachian coal fields and not in a coal seam of the thickness range of 42 to 72 inches. The first screening eliminated 30 of the listed operations, leaving 48.

Jan 1, 1976

By Anthony Iannacchione, Christopher Mark

Residents of Maxwell Hill, a suburb of Beckley, West Virginia, reported from January until March of 1988 a series of earth tremors. The tremors rattled dishes, and the noises associated with tremors were sometimes loud enough to wake people at night. These events were puzzling because Beckley is in an area of low seismic activity. Maxwell Hill is located above abandoned coal mines, though no direct subsidence damage to surface structures has been documented. A research program was initiated to determine whether subsurface ground movements associated with the abandoned mines could be responsible for the seismic activity experienced at the surface. A hypothesis is proposed which states that seismic disturbances can be caused by abandoned mine failure when two conditions are met. First, some instability must exist at the mine level. The most likely cause of instability is the failure of pillars of coal that were left for support at the time of mining. Second, subsurface movements can result in significant seismic activity only when the rock above the mine contains at least one very strong and brittle layer that is prone to fail violently through rupture or fault slip movement. Analysis of the data indicates that both hypothesized conditions for mine-related seismicity appear to have been satisfied in the case of Maxwell Hill. It has therefore been concluded that the earth tremors experienced by Maxwell Hill residents probably are related to the abandoned mines. Analysis of the potential magnitude of these events indicates that they are unlikely to cause significant surface danlage. The probability that future events will disturb the residence of Maxwell Hill should be quite low based on the identified mechanism.

By Harry R. Nicholls

The objectives of this investigation were to determine the strain propagation laws for a strain pulse in salt and to compare the seismic effects from the detonation of different explosives in salt. The investigation showed that a strain propagation law of the type, e = K(R/W 1/3 ) n, and a strain energy propagation law of the type, Ea/W 1/3 = K(R/WI/3)b , are valid in salt. A change in the regression law coefficient, n , was noted with strain level. A similar change in b was inferred because strain energy is proportional to the square of strain amplitude. Particle velocity data may be used interchangeably with strain data under the test conditions.

Jan 1, 1962

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By John W. Sweeney

The southeastern phosphate industry is investigated to determine its role in supplying the United States and world phosphate demand. The report shows that the southeastern (Florida, Tennessee, and North Carolina) phosphate industry is the leading domestic and world producer of phosphate rock, The report emphasizes size and organization, production capacity, transportation, and marketing of the southeastern phosphate product, Factors affecting the supply- demand relationship of the southeastern phosphate industry and world phosphate production-consumption relationships are analyzed and related to the southeastern phosphate industry. Past trends are projected and the future role of the southeastern phosphate industry is analyzed to determine its ability to supply the United States and rest-of-the-world phosphate requirements in 1985 and 2000. The projections show that southeastern resources are ample to supply domestic and export requirements at the projected rates of consumption well beyond the year 2000.

Jan 1, 1970

By Thomas M. Barczak

The era of the shield-supported longwall face began in the United States a little over 25 years ago. The most fundamental development of the shield in the past 25 years has been an increase in size and capacity and a progression toward two-legged designs in favor over four-legged shields. Is the “bigger-the-better” design philosophy justified? The advantage of the two-legged design is largely attributed to its active horizontal force caused by the forward orientation of the leg cylinders. How do we know this? You might be surprised to learn that shield loading data may suggest otherwise. In addition, what about setting pressures? Should they be set as high as possible? Some people have advocated that setting pressures should equal the yield pressure. Does this make any sense? Is yielding a good or bad thing? These are some questions still worthy of investigation that are addressed in this paper. The first major change in gateroad support was the use of cable bolts to replace conventional wood cribbing particularly in Western mines. Standing support changed very little until the mid-1990s, when Strata Products1 introduced the Hercules and Propsetter supports in Eastern mines and Burrell Mining Products introduced the Can support in Western mines. Since then, there has been a dramatic increase in new roof support technologies for longwall gateroad support. Historically, standing support, including shield supports, have been designed based on a simplistic model requiring the support to have sufficient capacity to support the gravity loading of a perceived detached rock mass. This approach ignores the stiffness of the support and the resulting ground deformation that is known to be critical to roof stability. Recently, a new approach based on the ground reaction concept has been promoted by the National Institute for Occupational Safety and Health (NIOSH) to account for the interaction of the support with the rock mass behavior in achieving ground stability. In addition to gateroad support design, this concept has ramifications for shield capacities, setting pressures, and recovery room support design that challenge current practices in these areas. Although longwall mining has matured into the safest and most productive underground mining method used today, traditional concepts of roof support design and practice should still be evaluated and challenged. Ultimately, advancements in the science of ground control are made by recognizing deficiencies in current theories and thinking outside the box.

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962