Search Documents

"In this work a blasting seismograph was tested on a vibration shaker controlled by a single-point laser Doppler vibrometer (LDV). A total of 43 tests were made to measure the transfer properties(transmissibility and phase shift) of the basic elements of the full monitoring chain and investigate theperformance of the full system. The main elements of the seismograph are described by second ordertransfer functions with typical parameters calibrated through nonlinear fit of the measured responses. The resulting transfer function is used to compare the behavior of the tested seismograph with fourtheoretical seismographs representative of those used in blasting. Fifteen theoretical inputs are runthrough the transfer function of each seismograph to assess their steady-response. The error (expressed as gain) in the peak velocity has been assessed. It varies from -1.5 to 2.3 dB (equivalent to atransmissibility of 0.84 to 1.3, respectively) depending on the seismograph and frequencies of the input.The largest errors occurred for input signals with frequencies in the low (<32 Hz) or high ranges (>125Hz), where the mechanical, electronics and digital parts of the seismograph modify the signals. Seismographs with the nominal transfer function described by DIN 45669:1:2010 are ranked with the smallest errors. Monitoring devices with transmissibility around one in a narrow bandwidth, in line with ISEE suggested criteria for amplitude response, involve large phase shifts at low and high frequencies, resulting in a worst performance."

Jan 1, 2017

In this paper, the author points out the need to beware of simple time correlations as proof of cause and effect when comparing building cracks and blasting operations. There is a need to be aware of the many other causes besides blasting which affect buildings. Some of these have histories of cyclic behavior; others have a long-term increasing effect on aging and deterioration, often with poorly defined time histories. Many are so strongly site specific that generic relationships are difficult to quantify.

Jan 1, 1981

By Robert J. Nothnagle, Kristen Franz Begor, Rodney W. Sutch

Recovery of contaminated groundwater in a fractured bedrock system presents some unique problems. Typically, the most common problem occurs from the inability to adequately characterize the discrete fractures through which contaminants may be migrating. Without adequate characterization, difficulties arise in properly positioning recovery wells and verifying the performance of the system. To overcome these difficulties at a site in Upstate New York, an innovative approach was developed involving the creation of an artificial fracture zone through controlled blasting to intercept contaminated groundwater flow.

Jan 1, 1988

By Ron Ketterling

We will discuss electronic and paper record keeping, what works and what doesn’t. We’ll review record keeping in light of those five sub-committees: Audit, Awards, Constitution, Ethics and Planning. You’ll come away with concrete steps you can use to improve your record keeping processes

Feb 1, 2020

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020

By D. Lynn Gordon, Larry B. Weston, Michael W. Manhart, Patrick R. Bowden, Michael W. Redmond

Study of confinement effects on detonation characteristics and subsequent fitting form development as a function of confiner strength and thickness.

Feb 1, 2020

By Rakesh Raghavaraju, Bibhu Mohanty

The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

Feb 1, 2020

By Rakesh Raghavaraju, Bibhu Mohanty

Prediction of fracture and fragmentation characteristics of a rock mass subjected to dynamic loads, such as in blasting remains a major technical challenge. The present study is aimed at characterizing the shock transmission properties in controlled experiments in small scale in a well-characterized granitic rock, under varying borehole coupling conditions. Single blast-hole tests were conducted in a granitic rock sample of 145 mm (5.7 inches) diameter and height. The boreholes (in two diameters: 6.4 mm (1/4 inch) or 9.5 mm (3/8 inch)) were loaded with detonating cord of varying charge weight (5.3 g/m or 25 grains/ft to 31.8 g/m or 150 grains/ft of PETN). The effect of explosion gas penetration into the target rock was eliminated by inserting a thin-walled copper liner along the borehole wall. Embedded carbon composite resisters were employed at varying distances from the borehole to measure transmitted shock pressure for two coupling conditions (i.e. air and water) at distances of 1x to 9x the borehole diameter. The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

By Eduardo Lozano, Vilem Petr

The use of explosives brings countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition, and avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation.

Jan 1, 2017

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"An Event Tree Analysis (ETA) is an established approach for logically deconstructing and assessing scenarios for probabilistic risk assessment. This deconstruction into a series of understandable eventsfacilitates probability estimation for explicitly defined explosive terrorism scenarios with consideration of modes of possible failure during execution (a scenario is defined through selection of a target, selection of an explosive material, and interdiction prior to arriving at general target location, etc.). Further, each event is decomposed into a range of possible outcomes. The physical action or reality ofthe outcome is statistically represented by “branches” of the event tree (e.g., the terrorist may choose totarget a stadium, hotel, or subway; terrorists may be successful or unsuccessful in acquiring the material)."

Jan 1, 2017

By Ron Ketterling

Donna Summer wrote and recorded a song in 1983 with Michael Omartian called, “She Works Hard for the Money.” The song was inspired by her encounter with an exhausted rest room attendant, Onetta Johnson, who is mentioned in the song by name, and featured on the album’s back cover. ISEE President James Daley, in the May/June 2019 in The Journal of Explosives Engineering discussed the Six Pillars related to the ISEE. We will use the Internal Processes pillar to frame this discussion. The Internal Process Pillar includes five separate sub-committees – we will see how this concept applies to both ATF Explosives record-keeping compliance and business process compliance in general. We will discuss electronic and paper record keeping, what works and what doesn’t. We’ll review record keeping in light of those five sub-committees: Audit, Awards, Constitution, Ethics and Planning. You’ll come away with concrete steps you can use to improve your record keeping processes. This paper will show you how to make the hard work of inventory management and ATF record keeping work hard for you.

By H Fukui, K Ichikawa, K Aikou, E Suzuki

An electronic delay detonator (EDD) consisting of a digital-base electronic delay module and a conventional instantaneous detonator module, designed for series connections with a special adjustable-output blasting machine, is described and shown to provide a delay time accuracy some four to twelve times higher than that of pyrotechnic millisecond and decisecond delay detonators, together with the other performance characteristics necessary for practical use. Also described is a blasting design system which allows effective reduction of ground and air vibration, through the use of EDDs with optimum delay times as determined by accurate computer simulation based on wave form and other data obtained from an on-site single-shot test blast.

Jan 1, 1989

By Jose A. Sanchidrián, Ricardo Castedo, Pablo Segarra, Juan Navarro

A study conducted at a mine site that used traditional field surveying and physical hole spot markings bench marked their combined drill and blast performance. The analysis of the operational expenditure (OPEX) improvement determined there were many measurable cost improvements. A primary factor that most operations have to deal with is over drilling of holes. This alone impacts the cost due to nonproductive labor allocations, excessive explosive costs, increased drill tool costs, increased drilling costs and has an impact on the downstream operation cost such as digging the shot material. Other related investigations also show a downstream impact of poor fragmentation on digging payload tonnes, cycle times, haulage payload tonnes, time to load a truck and the number of passes to load the tuck. The intent of this presentation is to draw attention to aspects of mining we understand but may be missing the big picture effects, such as the ability to reduce the operational expenditures consistently to impact the bottom line. The target audience is across the board from owner operators, drill and blast contractors to blasting contractors. Everyone can benefit from these improvements.

Jan 1, 2019

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By Paul Schmiesing, Matt Higgins

Central Oregon is a fast growing resort community centered in Bend, Oregon. Bend is bordered by the Cascade Mountains to the west and the high dessert to the east. Central Oregon is blanketed with lava rock with little topsoil. Ditch blasting is a staple in the area. Almost all utilities excavation (gas lines, sewer lines, water lines, and electrical lines) requires blasting. There is also a considerable amount of blasting required for site excavations and drywells. On average, there are over 500 blasts per year in Bend alone. All of this blasting is done using small holes, generally 2.5 inches in diameter. Typical ditches will have 200 holes, between 2-3 rows wide, with an average depth of 8 feet, and on 36 inch centers. Almost all shots are dry. Successful blasting requires careful control of drilling and loading. The vesicular basalt contains numerous lava tubes and caves making drilling and loading difficult. The rock conditions vary greatly from one side of town to the other requiring different powder factors and different scale of distances for vibration control. Caret%1 calculations of vibration predictions and use of site-specific seismic info is necessary. Marry shots will require deck loading and careful timing to ensure one-charge per delay. It is an every day occurrence to be blasting near residential and commercial structures or high pressure gas lines. Many times ditch blasting will incorporate excavation blasting. The different hole patterns used for the ditches and the excavation shots presents challenging timing sequences.

Jan 1, 2000

By Lon Santis

This paper describes several applications of quantitative risk assessment in the management of commercial explosives operations. The Institute of Makers of Explosives’ (IME) quantitative risk assessment software modeling program IMESAFR was used for this analysis. Modeled activities include the unloading of a ship at port, locating a safe haven, and dealing with encroachment on a manufacturing facility. The layout of actual explosives sites were used for the analysis. The risk of fatality is analyzed and shown it can be used to make informed operational decisions for each activity. A study of the risks to individuals from activities involving commercial explosives compared to individual risks from other daily activities or exposures is also presented.

Jan 1, 2008

By Krishna Nand

For assessing the safety of structures during underground explosions, ground particle velocity gives the best damage criteria, and 100 mm/see of ground particle velocity has been internationally accepted as the threshold value of safety (no damage). Results of extensive controlled underground explosion experiments conducted by the author to study the effects of ground vibrations on specially prepared concrete blocks, and also on low rise buildings and dams showed that no damage normally occurred when ground particle velocities were less than 100 mm/sec. Analysis of a large number of accelerograms from a dam site in India also indicated that no damage occurred to normal structures when integrated ground particle velocities were less than 100 mm/sec. Major damage in well built structures like a dam was noticed for ground particle velocity as high as about 350 mm/sec. These results are also generally substantiated from damage data obtained for various structures during other earthquakes, including Elcentro (1940), Taft (1952), Parkfield (1965), and San Fernando (1971). These studies, therefore, suggest that the damage criteria during underground explosions and earthquakes are similar; and 100 mm/see of ground particle velocity seems to be the general threshold value of safety (no damage) against ground vibrations.

Jan 1, 1988

By Joseph A. Meyers

NYC has always been a high-profile target for both foreign and domestic terrorists. Explosives have always been the go-to tool for terrorists to bring about serious physical injury, death, and property damage in our society. Today with the anti-police movement gaining traction in the United States and anarchists groups using homemade explosives against law enforcement and municipalities, it is the responsibility of the explosives industry to ensure that every explosive product on a blasting site is secure. We must prevent the theft of these energetic materials used on projects and sold by vendors so they are not used by these terrorists. We have learned many lessons here in NYC which began with the theft of explosives used for blasting projects in NYC to supply the IRA (Irish Republican Army) 50 years ago. The liability is too significant to take short cuts in securing energetic materials. Over the years through cooperation with all agencies and the industry we in NYC have developed certain proven protocol and procedures we would like to share with the industry. An efficient and effective security plan for the logistic movement of explosives, as well as for the blast site is imperative to keeping the good name of the industry from negative repercussions and possible additional bureaucratic oversight of an industry that is highly regulated and still recovering from the pandemic. Communication, security assessments and transparency with all stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the overall security for the blasting project. This SOP (standard operating procedure) will allow the AHJ to become a proactive partner in the security of the blasting project. If the AHJ is not a law enforcement agency, the law enforcement agency specialty unit must be notified and included in all phases of the project. The security for a blasting project with AHJ and law enforcement input starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. This includes threat assessments on new and existing structures. SME’s (Subject Matter Experts) must be present at all stages. The blasting industry and regulators must work collaboratively to improve safety, security, and create a dialogue with law enforcement and the AHJ. Relationships are built through trust, teamwork, transparency, and communication and greatly improve the safety of our great country.

Jan 21, 2025

By Hideaki Kitajima, Ryo Sakamoto, Katsuya Sasaki, Maehata Hidehiko

The Electric Discharge Impulse Crushing System (EDICS) is a technology for carrying out crushing by using electrical power and nitromethane. It is designed for construction tasks such as splitting of concrete and rocks.The EDICS consists of an electric discharge generator that supplies a high-voltage high-current pulse, a cartridge that generates power by using electric discharge energy, and cables that connect the electric discharge generator and the cartridge. The cartridge contains a thin metal wire that evaporates because of the electric discharge energy and a nitromethane that reacts with this evaporated metal wire. The cartridge can be used to generate a high pressure on the order of gigapascals within a time interval of several hundred microseconds, and crushing power equivalent to that generated by explosives is generated during this period. In recent years, the EDICS has been widely used in Japan because of its good performance and favorable characteristics.

Jan 1, 2011

By Jeffrey Loeb

Recent trends in blasting engineering and its related fields, at the level of professional academia, have tended to exclude detailed discussion and examination of the formative experiences of the engineering student. In particular, the extra-curricular aspects of the undergraduate program in engineering—focused, in this case, on the summer job—will be shown to contain a wealth of heretofore underappreciated knowledge in the field. In Surveying the Damage: Post Traumatic Stress and Pre-Blast Surveys, I intend to outline and examine some of the more unusual experiences afforded me by my work as a preblast surveyor in the summer of 2007. In this capacity, I was required to make a visual note of existing conditions of surrounding residential and commercial structures within 100 m (328 ft) of two separate blasting sites in central-east Ontario. In the interest of both convenience and specificity, I have attempted to organize the paper as a crossdiscipline survey of the field according to the conference’s list of suggested topics. In the paper’s first section, I will discuss the topic of Environmental Improvement and Remediation by using a case study in which not one, but two dead cats were found during the course of a routine pre-blast survey. The second section will undertake a discussion of on-site blaster gossip as an entry point into a wider discussion of Workplace Communications Management. In the paper’s final section, I will detail an early morning encounter with a 300 lb, stark-naked trailer park inhabitant as a cross-sectional analysis of the topics of Drilling in Hostile Environments, Vibration and Seismology (Sizemology?), Ethics in Blasting, Crisis Management, Risk Assessment and Public Relations. It is my hope that this paper will begin to open up a critical space for discussion of the formative experiences of engineering students during the undergraduate university program in terms of their far-reaching effects on later performance within the industry.

Jan 1, 2009