Search Documents

By D. Saramak

The proposal of the nip zone angle determination in HPGR crushing process is presented in the paper. Knowledge of the nip zone angle value, in turn, makes it possible to determine the real maximum pressing force in the high-pressure comminution. Two methods of determination of this maximum pressure were proposed and verified. The first method is based on the roll?s geometry, and the change of the HPGR chamber?s volume together with the roll rotation, while the second one considers the outlet gap width impact. Results of the nip zone angle calculations according to both methods are similar and show convergence with the real operating conditions. The verification was carried out in a piston-die press, and experimental results show that methodology of the nip zone angle determination presented in the paper has its practical confirmation. A proper determination of the nip zone border makes it possible to calculate the comminution probability of given type of material and is a basis for the HPGR crushing process modeling and optimization. Keywords: HPGR, comminution, nip zone, ore processing

Sep 1, 2012

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

By N. Dhawan

In the last decades, High Pressure Grinding Roll (HPGR) has gained significant importance in hard rock processing due to numerous metallurgical benefits such as energy savings, particle weakening, preferential damage of coarse particles, and preferential comminution-liberation. There are a limited numbers of lab-scale HPGR units throughout the world. The laboratory-scale HPGR machine at the University of Utah is first-ever lab-scale machine designed by late Dr Klaus Schönert, the inventor of HPGR. This HPGR is constructed with two counter-rotating hardened tool steel rolls, each 200 mm in diameter and 100 mm in width. The HPGR unit is equipped with eight sensors and a robust control system, which serves as an ideal system for fundamental studies and lab-scale testing. In HPGR operation, throughput, energy and product size distribution are intricately linked to specific grinding pressure, roll gap and rolls speed. The nip angle existing during the operation determines the volume of feed material above the rolls that is pulled into rolls without slip. In this paper, scale-up factors and some of the existing models have been reviewed. A number of experiments have been carried out with limestone and a slag material. The influence of operating variables and their complex relationship has been studied.

Sep 1, 2012

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Di Liu, Yongjun Peng

"It was identified that clay minerals adversely affect fine coal flotation through slime coatings. In the study, it was interesting to find that an anionic polymer dispersant, lignosulfonate, successfully mitigated the negative effect of clay minerals in coal flotation using fresh water, but in saline water, it exacerbated coal flotation.In order to understand the mechanisms underpinning the different behaviour of lignosulfonate in coal flotation using fresh and saline water, the adsorption isotherm, and dynamic light scattering (DLS) measurements were conducted in this study. While DLS monitored the molecular conformation change (swelling or shrinking) of the polymer in fresh and saline water, adsorption isotherms enabled polymer adsorbed amount on clay and coal mineral surfaces to be determined. It was found that lignosulfonate adsorbed on the coal and clay mineral surfaces providing effective electrostatic repulsions and resulting in a mitigation of clay minerals from coal surfaces in deionised water. In the presence of saline water, however, polymer molecular conformation changed. Polymer molecules were compressed and adsorbed in form of aggregates. The adsorption amount of lignosulfonate on clay minerals increased in saline water. A low dosage of lignosulfonate could not provide sufficient electrosteric repulsion to disperse clay minerals. Moreover, the high adsorption amount of the polymer on coal and clay surfaces led to a more hydrophilic coal surface, and coal flotation was therefore depressed in saline water. This study provides a new insight into understanding the role of anionic polymeric dispersants in mineral flotation using different quality water."

Jan 1, 2014

By C. Han

The analytical results of Dagushan grinding workshop primary grinding operation product show that the size fraction of -0.079mm is 32.88%, the size fraction of -0.01mm is 9.97%, the rate of -0.01mm size fraction and -0.079mm size fraction is 30.32%. It means that there is too much -0.01mm size fraction in primary grinding operation product and fall out that there will not be a better result in following operations. Several tests have been carried out to control the size distributing of the primary grinding operation product according to confirm the appropriate conditions of grinding operation. Integrate with theoretic count, grinding property tests show that the appropriate rev ratio of ball mill should be between 85% and 90% so as to get better size distributing. Based on the results of grinding property tests, the shocking property tests simulated the momentum of different diameter steel balls in the ball mill have been carried out. It showed that if want to get better size distributing the appropriate diameter of steel ball should be 110mm. The tests result shows that regulate diameter of steel ball and rev ratio of ball mill could control the size distributing. Contrast to the technical parameters of ball mill in grinding operation now, there are some significant advices are given for practice and industrial tests.

Jan 1, 2014

By Andries Van Wyk, Steven Bradshaw, Guven Akdogan, Jacques Eksteen, Cornelius Snyders, Cleophace Mpinga

"In order to exploit lower grade and complex platinum group metal resources, cheaper and more efficient alternatives to the conventional mill-float-smelt-refine route are being sought, particularly for resources’ in areas that are water-scarce and where electrification is costly and problematic. Leaching with cyanide is a promising process option and although recoveries are lower than in the conventional process routes, progress into the understanding of cyanide leaching of PGM containing ore and concentrate has been made. Research regarding the feasibility of upgrading the pregnant PGM leach solution using activated carbon has, however, been lacking and hence forms the focus of this paper. Bottle roll adsorption tests for dilute PGM solutions (0.15ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) onto granular activated carbon showed high rates within the first 60 minutes (giving more than 90% recovery of precious metals). Comparison of the Pt isotherm to Au isotherms from literature indicated a similar loading capacity, while that of Pd was found to be significantly lower. The effects of solution pH, temperature, base metal concentration, free cyanide concentration, thiocyanate concentration, initial PGM concentration and activated carbon concentration were investigated and are discussed. Elution of the Pt and Pd, with the AARL elution process, was found to be effective with recoveries of 95% after 5 bed volumes of eluant at the optimum pre-treatment concentrations and a temperature of 80°C. Temperature, NaCN and NaOH pre-treatment concentration and the ionic strength of the eluant were found to be the most important factors affecting elution while base metals concentration, acid-pre-treatment, carbon loading and thiocyanate concentrations to a lesser extent. Simplified combined flow sheets are suggested and the corresponding mass balances are compared."

Jan 1, 2014

By Alex Heath, Andrew Barycki, Baladron. Javier

"Efficient flocculation is important to thickener performance, affecting the overflow clarity, solids settling flux, underflow density and operability. Many factors affect flocculation; from the material/flocculant type, dilution of the feed and flocculant solution, mixing, to the shear rate and shear history. The flocculant addition point (or points) can be used as a tuning method to alter the effective flocculation time in a feedwell, with addition further up the feed pipe increasing the residence time but making the aggregates more prone to breakup if they experience high shear later in the process. Conversely, adding the flocculant later, eg under the feedwell shelf decreases the mixing time but allows some free (unadsorbed) flocculant to be available at the feedwell exit. An extensive trial has been performed on an operating thickener comparing seven individual different flocculant dosing positions through a Vane feedwell, and some combinations of two dosing points simultaneously. Measurements of the velocity, solids concentration and aggregate size were made throughout the feedwell at the different positions, with the dosing points significantly changing the aggregate size and clarity, and also affecting the solids concentration at some positions. The results are accessed in terms of flocculation kinetics and used as CFD validation data."

Jan 1, 2014

By Paulo Castillo, Cesar Gomez, Jaime Alvarez

Operations using flotation to produce mineral concentrates require testing of frothers to characterize their ability to preserve bubble formation size and to build a stable froth. Many techniques have been proposed to measure parameters associated with these two roles. These techniques focus, in general, on only one of these roles and are based on special equipment operated at conditions quite different from those existing in industrial cells and columns. Both roles have been simultaneously characterized in a laboratory flotation column, but the requirements associated with the installation and operation of one of these units, are a serious limitation for its use on-site. A technique based on the use of a laboratory mechanical cell, a common piece of equipment in operations, will have wider application. Establishing the ability of a frother to control coalescence by preserving bubble formation size is done through bubble size measurements as a function of frother concentration. Froth build-up and stabilization is associated with the amount of water carried by bubbles into the froth layer, which has been demonstrated to correlate with the gas holdup in the collection zone. Procedures devised for determining the critical coalescence concentration (CCC) from measurements of bubble size as a function of frother concentration, and the gas holdup by collection of water displaced from the cell by the presence of bubbles at different frother concentrations, were tested. Three analytical-grade frothers were utilized: a straight-chain (1-heptanol) and a branched (MIBC) alcohol and a polyglycol (PPG425). The results obtained at a standard set of conditions, demonstrated consistent differences between these frothers, and the ranking from least to most effective for reducing bubble size or decreasing water drainage followed the same sequences found when more complex frother characterization techniques are used.

Jan 1, 2014

By Shi Shuaixing Zhang Yuejun, Fan Xuesai Zhangming

"For the traditional principle of flotation cell design, or in the perspective of some researchers, the mixing effect of impeller for flotation cell is not only to suspend the particles off the bottom, but also to mix slurry well to achieve a uniform system. But for some special processing conditions, the depth profile of slurry concentration and particle size demonstrates an obvious difference. In the part around of the impeller in the cell, the slurry concentration is much higher than the part below the lip.For the vanadium titano-magnetite flotation process, distinguished with high concentration and large coarse particle size fraction, even though the concentration is very high, it can reach good gas dispersion, which is a fundamental principle for flotation cell design and application. The gas dispersion is not a challenge in the high slurry concentration environment, not only in the vertical direction, but in the cross section. Different levels (the distance from the lip is 400mm, 700mm, 1200mm, 1700mm, 2200mm, 2700mm) slurry in the flotation cell is sampled and analyzed. The slurry concentration of the 3 levels(1700mm, 2200mm, 2700mm) is about 55%, but the slurry concentration decreases from 55% to 25% sharply towards the lip.Therefore, a new understanding and viewpoint is presented, that the uniform system of slurry is not always reasonable for all of the flotation process. For some special process, if the coarse particles are needed to agitated well and transported to the upper cell, the quiescent zone in the upper cell will be destroyed and enhance the detachment probability for the coarse particles. The difference of slurry concentration and particle size fraction benefits the air dispersion and coarse mineral particles recovery.1.INTRODUCTIONNowadays, flotation is the most widely used separation process in the mineral processing industry. The importance of flotation technology in the global economy is significant. A rough estimate of the quantity of crushed ore treated by flotation is about nine billion tons per year, and the portion of base metals processed using this method is approximately 95% (Brewis, 1996)."

Jan 1, 2018

"The thiosulfate leaching process developed by Barrick to treat sulfidic high preg-robbing gold ores uses calcium thiosulfate as the leaching reagent for ores pre-treated by pressure oxidation, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a means of reagent recovery. A large portion of the research that led to the development of the technology was based on previous studies completed by different groups over the years, mainly focused on the ammonium thiosulfate system. Operational limitations in the use of the ammonia-containing recycled water in the pressure oxidation circuit were some of the main drivers for the change from ammonium to calcium thiosulfate for the development of the industrial scale process. One of the main aspects for successful gold extraction and recovery in the thiosulfate system is the pseudo-equilibrium reactions that drive distribution of the different gold species (in solids, solution and on resin) in the system. Previous studies have been focused on the thiosulfate reactions and equilibrium constants for the oxysulfur ions (thiosulfate, trithionate, tetrathionate). However, the literature around the effects of the different metal-oxysulfur complexes (Cu and Hg complexes) that form when the ore is in contact with the leaching reagents, and the related effects on stability of the gold complex is limited. The main changes in the gold complex chemistry and stability in the calcium thiosulfate system as compared to the ammonium and sodium equivalents, as well as related effects on gold recoveries, were investigated in the presence of different types of double refractory ores. INTRODUCTION Barrick has developed a thiosulfate leaching process to treat double refractory gold ores, by combining the use of acidic and alkaline autoclave pre-treatment with thiosulfate resin-in-leach (RIL). The process currently in operation at the Goldstrike mine (the TCM process), uses calcium thiosulfate as the leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recycle. The main feed to the process plant is highly preg-robbing sulfidic ore from Goldstrike’s open pit. Prior to feeding the pressure oxidation circuit, the ore is processed through the crushing and grinding circuits and treated in preparation for acid or alkaline autoclave processing (POX)."

Jan 1, 2018

By M. Bergerman

Sossego was the first Vale SAG mill operation to process copper-gold ore. It is located in Para state, south east of Amazon region in Brazil. The comminution circuit was designed to treat 41 000 metric tons per day comprising primary crushing, one 11.6 m SAG mill operating in closed configuration with cone crushers, followed by two 6.7 ball mills. In the first three years of continuous operation Vale investigated alternatives for obtained improved performance of the circuit by investigating operating conditions, mainly focusing on SAG mill. A number of actions were then implemented, which resulted in significant increase in overall production. Vale then decided to further assess the performance of the comminution circuit as a function of ore characteristics. A comprehensive ore characterization program was then conducted, together with the calibration of mathematical models on the basis of surveys carried out at the industrial circuit. The simulator was then used to predict the production level associated to each ore type, as well as to establish the optimized circuit configuration and tailored operating conditions. The ongoing validation program is planned to consolidate the selected strategy, as well as showing the benefits in adopting such indices in mine planning, as opposed to rather simplistic approaches. This paper describes in detail the main aspects of optimizing the industrial circuit performance, as well as the successful method for predicting the production as a function of ore characteristics.

Jan 1, 2014

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

By Ari Kokko

Metso has a long history supplying boilers for high ash coal firing. These boilers are based on circulating fluidized bed (CFB) technology. CFB?s biggest benefit is fuel flexibility ? it can burn fuels from high moisture content to high ash content. Metso has delivered tens of CFB boilers burning waste or high ash coal starting on 80?s. Some of the boilers have been in operation twenty years meaning that there is a long term experience from these plants available. This feedback includes boiler performance and maintenance issues of the boiler. Metso is also delivering coal washing plants to improve coal quality, i.e. reducing ash content of the coal. The idea to combine coal washing plant and CFB boiler was made up two years ago in Metso. Up-coming legislation of coal washing and restrictions for washery reject land-filling in India are good drivers for this kind of concept. Pre-study of this kind of concept led to the conclusion that coal washing process can be fine-tuned so that reject?s calorific value is only 1100 kcal/kg and that was set as a target for boiler design. Metso shipped 200 tons of washery reject to its own research center located in Tampere Finland. First a wide range of fuel characterization tests were done in lab-scale and after that one week test run in 4 MW CFB pilot boiler was done. Test run proved that 1100 kcal/kg can be fired without any support fuel with special boiler design. Test run results gave a good set of data regarding combustion efficiency, emission performance and boiler dynamic behaviour when burning this kind of fuel. These results are introduced in this paper. This paper introduces also the CFB boiler concept for washery reject firing including boiler plant, fuel and ash handling systems and flue gas cleaning system. Power plant can be integrated with coal washing plant so that boiler size matches with washing plants c

Sep 1, 2012

By Z. Q. Zhang

The iron ore from Yichang in China assaying 41.64% Fe and 1.02% P is a low grade and high phosphorus oolitic hematite ore. The separation of iron minerals from gangue minerals in the ore by conventional processing techniques is ineffective owing to their close similar properties. The modification of iron minerals by microwave-assisted reduction was investigated in order to improve separability of the ore. The effects of microwave-assisted reduction on the subsequent low intensity magnetic separation and floatation were examined. The results show that the main factors affecting the reduction and separation process are grinding size, reduction temperature and reductant. Fine grinding of the microwave-treated ore to smaller than 0.074mm was found to be imperative due to the tiny dissemination characteristics of iron oxide minerals. After magnetizing reduction by microwave heating at 500?, the magnetic concentrate containing 58.36% Fe and 0.67% P can be obtained with the Fe recovery of 91.28%. Magnetizing reduction drops the floatability of iron oxide minerals, thus reverse flotation is fit for upgrading the magnetic concentrate to contain 62.13% Fe and 0.21% P with Fe recovery of 81.59%. Compared with present microwave-assisted reduction technique of carbon reductant, using a waste iron powder as reductant is a novel and effective technique without the green house effect caused by the release of CO and CO2. Waste iron powder with a faster response to microwave heating then coke and charcoal can be recovered by magnetic separation in a low cost and plays the role of reductant and microwave heating accelerator.

Jan 1, 2014

By Xiaodong Jia, Williams. Richard A.

This paper describes the recent developments, arising from research at Leeds, in the computer modelling of packing of complex shaped particles and prediction of physical properties of the structures represented by the packing. The computer model DigiPac, is capable of packing particles of any shapes and sizes in a container of arbitrary geometry. The ability to predict packing structure of real particle shapes and to compute directly some structure-dependent physical properties (such as liquid permeability, mechanical strength/ stability, compaction and sintering, dissolution and leaching, etc.) is obviously highly desirable and has significant potential in industrial applications. Examples are presented relating to the packing of granular materials.

Jan 1, 2003

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

This paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.

Jan 1, 2003

By Baidyanath Mandal

Technology in the solid-liquid separation industry has evolved rapidly during the last fifty years and from the beginning, DIEMME Filtration has played a very important role in this evolutionary process by developing innovative solutions, which are used for a diverse range of industrial applications. Since the last decade, we find more and more examples of filter presses employed in the mining & mineral processing field, where high performances in terms of productivity, dewatering capacity and mechanical strength even in extreme working conditions are required. Mainly the requirement of such high quality equipment comes from the Process, however in few cases the reason could be linked with the environment. For stringent process applications like Mineral Concentrates dewatering & leached Slurry Filtration, it requires a high quality & extremely reliable equipment. In these applications, since many years industries are achieving the desired result by using Diemme Filter Presses. Also, recently, due to stringent environment practices are been applied globally, industries needs equipments which could dewater a high amount of residues / tailings with minimal moisture content in the filtered cake. In comparison to all the conventional dewatering equipments, Diemme Filter Presses are most efficient for these kind of product & applications. Diemme Filtration is a highly professional & technological company with several decades of experience in designing equipment for mineral processing. We take up each project as separate & design and manufacture equipment based on individual process or project requirement. This presentation will be focused on the Solid-Liquid separation technologies & equipment Diemme Filtration offers to the mineral processing Industries. It consists of Diemme?s History, Global Network, Technologies & Expertise, R & D Capabilities, Manufacturing Range, Some Applications & results on different mineral processing. Keywords: solid-liquid separation, filtration, dewatering, filter press

Sep 1, 2012