Search Documents

By Walid El Kamash, Sadik Oztoprak

"Soft soil presents a challenge against multistory buildings in some cities of Egypt such as Port Said due to the consolidation settlement. Deep mixed (DM) columns are used to improve the soft foundation soil in order to reduce the total and differential settlements. Latest research revealed that this improvement technique also increases the rate of mechanical consolidation due to column yielding caused by stress concentration from the soft soil. In this study, extended poly-styrene (EPS) Geofoam is used to replace the soft soil over DM columns in order to control the stress concentration and settlement. To understand the effect of EPS geofoam on the degree of consolidation, stress concentration and settlement, a parametric study was carried out through a mechanically and hydraulically-coupled numerical method. A unit cell model is used, in which the soil was considered linear elastic; DM column and EPS Geofoam are elasticplastic materials. Results reveal that EPS geofoam is helpful for reducing the settlements and accelerating the consolidation. Increasing the length of the column of the deep mixed foundation with EPS geofoam has a significant effect on accelerating the consolidation.INTRODUCTIONExpanded polystyrene (EPS) geofoam is a lightweight polymeric material which is made by expansion of raw plastic beads. The expansion of the EPS beads are spherical-shaped particles containing closed hollow cells. EPS which plays an important role as an innovative lightweight construction material is now well recognized due to its low density in addition to high compressive and rupture strength. Inglis (1996) reported the first use of EPS geofoam as a seismic buffer to reduce potential seismic loads against a nonyielding basement wall. Gaskin (2000) and Bathurst et al. (2007) carried out reduced-scale shaking table test on a rigid retaining wall protected by EPS geofoam. The test data showed that the peak lateral loads acting on compressible model walls were reduced below values measured for nominally identical structure but with no compressible inclusion. Abdelrahman and El Kamash (2014) investigated the behavior of EPS Geofoam beneath raft foundation on soft soil of Port Said. They showed the ability of EPS to control vertical displacements. The investigation of the behavior of EPS geofoam with DM column has not attracted more attention of previous researchers. In this paper, the behavior of replacing the soft soil by EPS geofoam was examined in the presence of DM column."

Jan 1, 2015

By Antonio Zechini, Giuseppe Iorio, Massimo Grisolia

"The new C Line of the Rome Metro runs northwest to southeast across the city center, with 30 new stations and a total length of more than 15.5 mi (25 km). Due to the presence of a dense urban environment, the selected solution for the construction of the stations consists of a cutand- cover excavation, which is retained by multipropped diaphragm walls to minimize settlement and prevent damage to the nearby structures. The bottom of the excavation of the underground stations are about 82 ft to 98 ft (25 m to 30 m) below ground surface, and about 66 ft to 82 ft (20 m to 25 m) below the groundwater table. To ensure dry conditions and to prevent hydraulic base heave instability, deep well systems were designed and used to lower groundwater level and piezometric head during excavation. The dewatering field tests showed how the local stratigraphy strongly affects the dewatering efficiency. Finite element modeling (FEM) of steady state filtration were used to compare the soil permeability with Lefranc in-situ test results and to verify the efficiency of the grouted plugs. The geological sequence along the new C Line consists of a very heterogeneously layered deposit. The base deposit of stiff overconsolidated clay (“APL,” Pliocene age) is overlain by fluvio-palustrine very dense sandy gravels (“SG,” Pleistocene age), which are then overlain by medium stiff clayey silts or dense sandy silts (“AR” or “ST,” Paleotevere units). These deposits are overlain by covered by pyroclastic volcanic soils, tuff, silty sand and sandy silt (Middle to Upper Pleistocene) deriving from the Colli Albani apparatus. A layer of made ground (“R”) of varying thickness covers the stratigraphic sequence and the natural soil profile everywhere.The local hydrogeological framework is very complex and characterized by a double groundwater system. The upper main aquifer is mainly represented by the “pozzolane sequences” (“PR/PN”), while the lower aquifer consists of a deposit of sandy gravel (“SG,” Pleistocene), which is underlain by marine claystone bedrock (“APL,” Pliocene). The pyroclastic deposits (e.g., pozzolane, lithoid and pseudolithoid tuff and clayely tuff) show large variations in permeability due to porosity, compaction processes, sealing and secondary fracturing. Permeability values for each soil type were determined using Lefranc tests at variable head and using pumping tests. The Lefranc tests indicated a wide range of permeability."

Jan 1, 2017

By John P. Turner, Benjamin J. Turner

"This report describes a research project for evaluating the applicability of the widely accepted 80 percent criterion for elongation of ground anchors to anchors with unbonded lengths exceeding 100 feet. This issue is driven by several recent projects involving ground anchors for landslide stabilization in which a significant percentage of the anchors did not meet the criterion that requires measured elongation during proof load testing of at least 80 percent of the theoretical elastic elongation. The projects involved anchor unbonded lengths in the range of 85 to 220 feet, which is outside the range traditionally used in practice, although anchors of this length are being used more frequently for landslide stabilization. The principal objective of this research is to address whether the widely accepted criterion of 80 percent elongation is applicable for such applications, and whether other factors affect the ability of anchors to meet the criterion.Analytical methods for predicting transfer of load along the length of steel strand due to friction loss are used routinely in the prestressed concrete industry. These analytical expressions provide a rational framework for quantifying changes in load due to friction along the length of a ground anchor in terms of a ‘wobble coefficient’ (K) as defined in Aalami (2004). Values of the wobble coefficient for ground anchors can only be determined by back-calculating from load tests, i.e., fit the value of K to the appropriate analytical expression based on the known test load and measured percent elongation. The analytical basis is first developed and shown to provide a tool for evaluating results of anchor load tests to determine the magnitude of expected elongation as a function of unbonded length. Next, a database of anchor load tests is used to back-calculate values of K for anchors with unbonded lengths in the range typically used in geotechnical applications (< 100 feet). These values of K are then used to calculate expected friction loss for anchors with high unbonded lengths (100 to 250 feet) to evaluate whether the 80 percent criterion is reasonable."

Jan 1, 2017

By Rasin Duzceer

In this paper, the results of pile load test on 24 piles from twelve sites are presented. The pile load tests were performed on 14 driven and 10 bored piles of varying diameters and lengths installed in different ground conditions in Turkey, Saudi Arabia and Kazakhstan. The purpose of this study is to evaluate and compare the axial capacity of the piles obtained using pile load test interpretation methods. Davisson, Brinch Hansen %80, Chin-Kondner, Shen-Niu, De-Beer, Housel, Mazurkiewicz, Fuller-Hoy, Brinch- Hansen (90%), Corps of Engineers, Butler Hoy and Tangent Intersection methods were used to determine the axial capacity of the piles. Static analysis using FHWA method was performed to predict the axial capacity of the piles. A statistical analysis was performed to compare and quantify the load test interpretation methods. The ratio of interpreted (Qi) to predicted (Qp) pile capacity was compared for each method. For each pile load test and for each interpretation method, the mean and coefficient of variation of (Qi)/ (Qp) were calculated. Among twelve methods investigated, the highest Qi/Qp value was obtained as 1.37 for Chin-Kondner method whereas the lowest Qi/Qp ratio of 0.70 was obtained from De Beer method.

Jan 1, 2002

By Brian McGlynn

There are many factors that can result in a site characterization being limited. For example, a client may undervalue the importance of a good geotechnical report, or an owner may feel that it would take too much time to perform an appropriate investigation among other reasons. For this project, neither was the case. The challenge was that the construction sequence of work required wick drains to accelerate the settlement of soil that had yet to be placed, resulting in the need to create a wick drain bid package based on unknown settlement parameters. This wick drain project took place in Long Beach, California, at the Long Beach Middle Harbor Re- development. For much of the past decade, the Port of Long Beach undertook a $1.5 billion redevelopment of two outdated terminals to create the Long Beach Container Terminal (LBCT). To achieve this goal, the existing terminals were demolished and the slip that serviced one of the older terminals was designed to be infilled to create the new area that would allow for the LBCT to manage 3.3 million TEUS (a commonly used freight term meaning twenty-foot equivalent unit) of cargo each year. Ultimately, the construction of the LBCT would be performed under multiple contracts to allow the new terminal to begin operation in a phased approach. Menard performed the wick drain installation under two out of three contracts, and this case history focuses on the challenges anticipated and faced under the second of these awarded contracts.

May 1, 2023

By Gerry Houlahan

The east span of the 3.5 km long SF-Oakland Bay Bridge is supported by different types of foundations along its span. Starting from the west, its first 460 m section comprising twin concrete box-girders is supported by sands and rock on Yerba Buena Island. A 620 m long steel suspension span then bridges a 25 m deep channel that is formed in sediments overlying rock. Twin concrete box girder structures, each 2.4 km long, complete the stretch over the remainder of San Francisco Bay to the engineered earth fill landing at its east end. For most of its length, the Skyway bridges water 3 to 10 m deep over soft surficial Young Bay Mud. The foundation types include spread footings with hold-downs, steel and concrete piles that are set in drilled rock sockets up to 3 m in diameter and 2.5 m diameter steel tubular piles driven to penetrations of up to 100 m. The design and construction-related considerations are presented. The different foundation types, influences of the site geology and earthquake demands on the substructures are discussed. The seismic motions of the bridge superstructures and substructures, as well as the depth-varying soil motions, influenced the foundation design. Together with performance-based design criteria, including post-earthquake footing displacement limits, these seismic demands influenced various aspects of the foundation design, including the use of battered and vertical piles.

Jan 1, 2013

By Xuhui

Pile foundations are underground projects which are carried out under complicated site conditions, so it is difficult to summarize their characteristic patterns from the everchanging practical pile foundations. In combination with theories, the paper analyses the effects of sound reinforced concrete piles and various types of defective piles on the propagations of stress waves. Through testing on prototype pile models, by use of the transient dynamic method and comprehensive analysis in both time domain and frequency domain, their reflection characteristics and patterns are acquired. In addition, discussions are carried out in combination with some real projects. Our model tests include comparison of large scale pile models of 20X20cm in cross section, 5. 0m in length respectively in air, standard sand, and natural stratum; prototype model tests of digged piles of 0. 7-1. 2m in diameter, and 18m, 30m in length; prototype model tests of bored piles of 0. 6m, 0. 8m in diameter, 12-20m in length. Test results show that no matter in air or buried in medium, the intrinsic characteristics of sound piles and various types of defective piles are fixed. In their time domain waveforms and spectral diagrams, obvious regularity are shown, which proves that the relations between the pile natures and their dynamic responses are fixed, which provide basis for correct judgement of pile soundness and natures of defective piles.

Jan 1, 1991

By Wei Tu

A grade separation was required to allow uninterrupted traffic crossing for a busy rail spur and a county road. The grade separation was achieved by creating a 30-foot (9-meter) high embankment that incorporates two multiplate tunnels and allows the passage of a rail spur and an existing county road. The site is located in an abandoned meander channel in the floodplain of the Mississippi River, near Osceola, Arkansas, and is underlain by more than 40 feet (12 meters) of soft clay and interlayered clays, sands and silts. Without soil improvement, the post-construction settlement would exceed 3 feet, slowly crushing the proposed tunnel structure and cutting off the railroad. Preloading, combined with vertical drains, was used to accelerate the consolidation of the underlying soil layers and to reduce the post-construction settlement under working loads. Six settlement plates were installed to monitor the progress of consolidation under surcharge load. The Asaoka observational method and the hyperbolic fitting method were used to analyze the measured settlement data to predict the end of primary settlement. The in-situ consolidation coefficient, ch, was back calculated from the measured settlement data. The stress release caused by the removal of the preloading surcharge load and the tunnel installation was determined using a Plaxis 3-D finite element model. The measured and predicted settlement using Hansbo&apos;s analytical solution demonstrated reasonable agreement. Early removal of the surcharge and construction of the tunnel prior to reaching the end of primary settlement was accomplished by analyzing the post-excavation stress reduction achieved via tunnel construction.

Jan 1, 2009

By Salim Mezazigh

Usually different methods for designing a single pile submitted to a lateral loading are available. They are based on theory of elasticity with the parameters E,v or subgrade reaction method using the p-y curves. The subgrade reaction methods are commonly used. They allow determining the efforts exerted along the piles and their corresponding displacements. Before any design the reaction curves P-y must be well defined for each foundation soil layer. These curves link the pile horizontal displacement y to the subgrade reaction of soil P. Different in situ tests such as the static penetrometer or the pressuremeter give a possibility to get the P-y curves in the case of a single pile installed in sand with an horizontal surface and statically laterally loaded. These ideal conditions are not always respected on the site around the pile if appear slopes, embankments, or buildings... The behaviour of such configurations of piles is more sophisticated due to the proximity ( slope, embankment, earthworks, buildings,..). A research program has been conducted to determine the influence of a slope on the P-y curves by centrifuge modelling. The centrifuge tests constitutes an experimental approach allowing parametric studies in respect with similitude laws in geotechnique. Before all, repeatable tests have demonstrated that the test conditions, the instrumentation equipment and the installation method for piles are well controlled. By this way, the obtained results from centrifuge tests can be transferred to the prototype i.e. the in situ piles. Many tests have been performed on piles in sand to determine the influence of a pile on the p-y curves. The main objective is to give for practice some coefficients to apply to p-y single pile curve to take into account the proximity slope effect. Here the experimental set up is described and in particular the proximity slope effect is discussed. Deduced subgrade reaction reduction factors are proposed for piles in sand under lateral loading.

Jan 1, 2002

By Jorj O. Osterberg

The practice of using side shear resistance in the design of drilled shafts socketed in rock is discussed. In the absence of field test data for the particular rock involved, the designer often neglects the side shear altogether or uses an extremely conservative value. The uncertainty of using strength data from compression tests on rock cores is discussed. Examples of full scale load tests are given which illustrate that even in the weakest of rocks, considerable side shear resistances are obtained, enabeling reductions in the depths of the sockets and consequent savings. Existing Practice. The existing design practice in using side friction/bond between a drilled shaft in rock or hard soil varies very considerably in different areas of the U.S., in different areas of the world, among different Geotechnical Engineers, and in the requirements of different building codes. In fact, the variation is so great that it is inconsistent and contradictory. For example, in Florida where fairly weak coral limestone and sandstone is prevalent, the general practice is to use side friction only and to allow no end bearing. In Chicago, Detroit, Boston and other areas where soft clay overlies stiffer clays, hardpan and limestone or other hard rock, the common practice is to allow for no friction and to use end bearing only, even though the lower portion of a shaft frequently penetrates stiff to hard clays and hardpan (glacial till) before bearing on hardpan or rock. In Hong Kong, if the hole is stabilized with drilling mud, no end bearing is allowed. In Boston (Thompson, Erikson, and Smith, 1989), two tests at two sites on 18 inch pipe piles penetrating 100 feet of soft clay and driven only inches into an argillite, tested 140 and 210 tons in ultimate side shear resistance. Certainly, with long drilled shafts, no matter how soft or weak the soil or rock is, some if not considerable side friction occurs, and where drilling mud is used, there must be considerable end bearing.

Jan 1, 1991

By Andrew Baxter

The Crystal Bridges Museum of American Art in Bentonville, Arkansas is a beautiful glass and concrete structure cut into a valley that mingles with water ponds spanned by multiple bridges with suspended roofs. Or, at least it will be when completed in 2009. At Crystal Bridges, most of the proposed buildings involve cuts up to 50 ft high to be retained by the building structures. This requires the construction of retaining walls adequately founded to support lateral loads of up to 70 kip/ft. To add to this difficulty, the site is within a karst region with all the variability and irregularities associated with solutioning and erosion of the parent rock in this environment. The irregular rock profile made it virtually impossible to conceive a predictable arrangement of shallow footings and shear keys for the retaining walls. The existence of layers of soft soils within a hard rock formation made a caisson foundation impractical. The authors developed an innovative solution based on micropiles, which proved to be invaluable from a cost and schedule point of view. In areas where rock was shallow, micropiles were used as ?shear pins? to transfer the horizontal loads to the rock. In areas with significant overburden, a system of vertical and battered micropiles was devised to carry vertical and horizontal loads from the retaining walls. This paper presents a detailed description of the design and installation of the micropiles used as shear pins, and includes the results of lateral load tests performed on full-scale models of the grade beams on shear pins. The work performed shows that micropiles in rock can be effectively utilized for support of significant lateral loads provided that an adequate arrangement of suitably sized micropiles is provided, and that micropiles used as shear pins may develop significant tensile stresses when loaded laterally.

Jan 1, 2008

"Every year during the Transportation Research Board (TRB) Annual Meeting in Washington D.C., the Federal Highway Administration (FHWA) National Geotechnical Team (NGT) takes time to talk about what we are doing in research, training development and policy support. At times, I have jokingly referred to it as the State of the Program Address, but we do see it as an important opportunity to update our transportation partners on priorities and needs for the program.This update is really a snapshot of the program during the previous year, with a look at projects that are currently active. Activities undertaken by the NGT are funded from multiyear roadmaps maintained by the FHWA program and research offices, and reflect trends and opportunities affecting and influencing transportation geotechnics now and in the future. The roadmaps identify activities in research, development, guidance, technology transfer and training that will be accomplished by the NGT through and beyond FY 2020 in eight broadly-defined focus areas: • Extreme events, geohazards and sustainable geotechnics• Performance management• Reliability-based design and construction• Advanced geotechnical modeling• Alternative delivery methods• Design and construction optimization• Site characterization• Quality assuranceThe process to identify focus areas and to develop activities that will be addressed by the NGT is guided and informed through input from the FHWA NGT members, and considers feedback and input from State Departments of Transportation (DOTs), FHWA Division offices, industry and academia. This process is revisited annually to review not only the activities that are currently funded, or will be funded, but also to review the relevance of the focus areas with respect to the future needs of the FHWA, State DOTs and the transportation community.In 2016, the NGT was successful in delivering several products that will advance the state of the practice and that better support policy. Products developed included research reports, design and construction guidance, and training courses. In 2017, the research and program offices will continue to work on projects that fit within our prioritized plan and that positively impact the geotechnical community as a whole. A listing of recently completed and currently active projects is provided below."

Jan 1, 2017

By John E. Lens

Driving bridge foundation piles into glacio-fluvial sands and gravels and glacial tills brought surprisingly longer than predicted driving lengths on several recent projects in Vermont. In some instances, piles drove more than 40 feet past refusal depths predicted from Standard Penetration Resistances from borings terminating in glacial till. Overall, piles developed substantially less skin friction than predicted using common capacity formulas and drove as much as 80 feet longer than predicted in the moderate to dense gravelly and cobbly soils. These piles were driven for one to five span highway bridges within narrow valleys with bedrock ranging from 80 to over 200 feet deep. Piles were for both conventional and integral abutment bridges. H-piles were used for a variety of reasons including lower unit cost, better availability, and better ability to drive through cobbly soils in upper strata. Dynamic testing was used to evaluate capacity, including skin friction and end bearing capacity. In order to develop better pile length and capacity predictions for future projects, VTrans and one of their geotechnical consultants are collaborating to develop criteria for improved pile capacity predictions in these river valleys. We are doing this by evaluating driving and dynamic testing data from four projects in comparison with the Federal Highway Administration (FHWA) DRIVEN pile design software, and methods from Myerhof (1976) and Tomlinson (1981). Our overall objective is to provide a basis for choosing appropriate pile types and reliably estimating pile lengths for projects in this terrain. Bridge foundation design projects in other mountainous terrain share similar design and construction challenges to those encountered in these Vermont projects. These include: difficult exploration drill rig access requiring smaller rigs with limited capability to drill through cobbles and boulders deep enough to reach bedrock; limited experience with displacement piles as alternatives to H-piles in this geology; and relatively greater variability in soil stratigraphy between foundations at these sites as a consequence of the relatively high energy depositional environment in mountainous terrain. This paper presents the case history summaries of the pile driving, results of the ?back analysis? capacity evaluations, examples of solutions employed on these projects to address the lower capacities achieved, and resulting pile capacity design guidelines and prediction criteria for these geologic conditions based on data from these projects.

Jan 1, 2007

By Aly M. Mohammad

The design of large diameter drilled shafts in weathered rock has always presented a challenge to the foundation engineers. Degree of weathering and load transfer mechanism through the rock are essential elements required for the design. From the Contractor&apos;s perspective specifying the right equipment and estimating the rate of drilling in the weathered rock are key elements for successful construction. The Delaware River Tramway Project has provided an opportunity to address the design and construction of drilled shafts in weathered rock. The Tramway, supported by twin 300-foot towers, will shuttle eight-person gondolas across the Delaware River in about four minutes. Each tower, founded on four high capacity drilled shafts, is designed to resist large axial and lateral loads. At the New Jersey tower, each 7-foot diameter shaft extends 145 feet deep and terminates in weathered Mica Schist. The shafts are situated in the Delaware River where the mud line is approximately 20 feet below Mean Low Water. Below the mud line, there exists a very soft, 20-foot thick layer of organic silt, followed by a 40-foot thick dense sand stratum. Below these sand and silt strata, a 70-foot thick layer of weathered Mica Schist underlies the entire site. Both skin friction and end bearing in the weathered rock stratum were utilized in the analysis to compute the axial capacity. AASHTO and the PennDOT design methodologies were utilized independently during design of the drilled shafts to verify the design. The drilling of large diameter drilled shafts embedded into weathered rock and situated in a marine environment provided a unique challenge in the construction. A permanent steel casing was installed for a specified depth and proper equipment was used to drill and keep the shaft open through the weathered rock. In addition, a 5000 kip Osterberg load test was performed on one shaft to verify design assumptions and confirm the shaft capacity. The results of the test were utilized to establish load transfer characteristics within the weathered rock and to develop foundation design parameters to be used for the remaining shafts.

Jan 1, 2003

By Ross Cutts

As a public servant geotechnical engineer, I observed how costly and valuable geotechnical field explorations are to the success of every project. Often however, the field exploration is a long and complex process that is made less efficient by the difficulty of retrieving and utilizing nearby internal or external historic geotechnical datasets. As an employee of a public agency, we would often start our investigations for every project from scratch, given the difficulty of locating and utilizing historic geotechnical data. This is an ethical and technical failing of our profession. When we start subsurface explorations from scratch, not only do we often duplicate investigations, we are also likely defaulting to reapplying tradi- tional test methods that yield con- servative geotechnical parameters, resulting in overly conservative and potentially costly construction. To address this issue while working as a public servant, I started a research program with Yunfeng Zhang, Ph.D., of the University of Maryland, to build a tool that could compile internal historic geotechnical data and extract additional value from it, using machine learning. This tool was able to provide, upon request, nearby historic geotechnical data, estimated soil parameters and recommendations for geotechnical test methods best suited for a given project site. This prevented common field ex- ploration problems such as, requesting duplicate data, requesting test methods that were not applicable for the project geology, not realizing presence of karsts, missing permits for wetlands, private property and others. This tool allowed for more efficient field investigations with regards to time and money saved. There was one problem with this tool: it could only be used by internal employees of a single state's depart- ment of transportation (DOT) for which this data was compiled. I realized at that point that it would be of tremendous value to make this concept universally accessible to the geotechnical engi- neering profession. I left public service to devote time to building a platform that would host historic geotechnical data from publicly funded sources throughout the country. The tool I helped build as a public servant was the foundation of Geosetta, a nonprofit company dedicated to serving the geotechnical profession. The nonprofit structure was adopted to prevent acquisition by a for-profit company and to ensure that Geosetta remains an independent steward of our profession's valuable data. Geosetta provides a GIS (geographic information system) platform that enables users to view historic geo- technical data and extract value from it with machine learning-based predictions and visualization tools. This data is provided in an open and interchangeable format called DIGGS, which stands for Data Interchange for Geotechnical and Geoenvironmental Specialists, making it easy for users to integrate it into their workflows. Geosetta is collaborating with the American Society of Civil Engineers' Geo-Institute and other sponsors to extract public data at no cost to the agency and provide the profession with free access to the existing data and access to advanced tools through a subscription to support the nonprofit mission.

Nov 1, 2023

By Alan Christopherson

Nearshore construction projects often require installation of steel piles and specific methodologies of installing piles may adversely affect nearby species of concern. Water is an uncompressible medium which allows for easy transmission of energy through the water column. Energy transmission through water depends on the following factors for pile driving: 1) direct contact of the pile and the water; 2) the depth of the water column; 3) the size of the pile; 4) type of hammer; and 5) the energy of the hammer. Seasonal restrictions are usually the best practicable alternative for reducing habitat impacts when pile driving activities may adversely affect the species of concern. When seasonal restrictions are not practical other options need to be evaluated, including mitigation and noise attenuation devices. The broad array of mitigation options will not be discussed as part of this presentation but instead will focus on noise attenuation technologies. Dewatered cofferdams can be effective noise attenuators as they eliminate direct contact of the pile with water while driving. Also, introduction of a compressible medium, like air, near the energy source can provide sound energy attenuation. An unconfined bubble curtain is relatively inexpensive but is not effective in tidal marine projects or rivers and may have unacceptable secondary effects. Secondary effects must be evaluated as these can increase exponentially for larger projects. Secondary effects to the environment include air quality degradation from air compressor use, transportation costs for fuel and equipment, and the potential for injecting oily compressed air into the water column. The confined bubble curtain works well in nearly all environments. It usually is more expensive initially, relative to an unconfined air curtain, but there is less potential for harmful secondary effects. Generally, seasonal restrictions will be adequate to protect species of concern. However, there are conditions in which mitigation or one of the sound attenuation options should be utilized. Site specific factors, including the amount of energy being imparted into the environment, sensitivity of the species of concern, current, accessibility, length of time needed to complete the project, and the cost of the sound attenuation, should be factored into the permit evaluation.

Jan 1, 2013

By Kyle M. Rollins

To improve our understanding of lateral resistance of pile groups, a series of lateral load tests were performed on a full-scale pile group using both static and dynamic loads. The pile group consisted of nine 0.6 m-diameter steel pipe piles driven into clay. During the static tests, the load was cycled fifteen times to evaluate the drop in lateral resistance that would occur due to repeated loading and the formation of a gap. The peak load typically decreased by about 15% from the initial cycle to the last cycle. The load carried by each pile was also measured and there was a significant drop in resistance for the piles in the trailing row relative to the leading row. The dynamic force was applied using the Statnamic loading system which produced a lateral force of 3500 kN (787 kips) in about 0.1 seconds. In two cases, dynamic loads were applied following application of 15 static load cycles. In these cases, the dynamic lateral resistance was about the same as the static resistance, likely due to gaps around the pile. In three other cases, the dynamic force was applied prior to the cyclic loading. In these cases, the dynamic resistance was 30 to 60% higher than the static resistance. Simplified analyses suggest that the difference in resistance could be attributed to damping produced by the soil surrounding the piles during the virgin loading.

Jan 1, 2002

By Walter G. Brusey

This paper describes a comprehensive pile test program conducted at John F. Kennedy International Airport (JFKIA) to evaluate pile types and design capacities ranging from 890 to 4450 KN (100 to 500 tons). Driven cased piles and drilled shafts, both standard construction and post-grouted after installation, were tested with platform loads extending to 8900 KN (1,000 tons). Alternate load test procedures were developed, extensive structural integrity testing and dynamic load tests were performed on selected shafts. A brief update is provided covering the application of results of the test program to pile selection for support of major structures incorporated in the on going redevelopment of JFKIA.

Jan 1, 2000

By James Warner

Although use of low mobility grout is just now beginning in some parts of the world, its advantage for many applications has been well established through more than 50 years of positive experience. The single largest area of application continues to be densification of soil by way of compaction grouting. Because it is often the safest and least costly method for soil improvement in general, and virtually always that in connection with soil improvement under, or adjacent to structures or in developed areas, use will undoubtedly increase both geographically and in diversity of application.

Feb 10, 2003

By Peter Iovino

Unfortunately, I don&apos;t know the unit cost per cubic yard of treatment. I reflected on that yesterday and I don&apos;t think that we considered the use of micropiles. They could have been an option. The challenge may have been picking up some of the lateral load but I think the micropiles could have been installed on a batter and perhaps extended to rock. We could have considered them, but I do not believe we explored micropiles as an option for this project.

Feb 10, 2003