Search Documents

Since the mid-1970s there has been increasing attention in the South Pacific area to the problems of disaster planning and management at various levels, mainly from regional through national to provincial levels. This concern has been expressed in a variety of ways. International aid donors have made their views known in commentaries or reports. Seminar discussions have been organised at the regional level (such as at Suva, 1976; Suva, 1979; Tonga, 1982 and Suva, 1983). In-country training workshops or meetings have been organised (such as the "Disaster Preparedness Workshops for Non-governmental Organisations" in Pacific countries, jointly run by the Australian Red Cross and the Australian Overseas Disaster Response Organisation and supported by AIDAB, in Vanuatu, 1985; Solomon Islands, 1985; Western Samoa, 1986; Fiji, 1987; Tonga, 1987; Lae and Port Moresby, Papua New Guinea, 1988) or held outside the area (ACDC at Macedon, 1981). Training and/or research institutions have been established such as the East-West Center, Honolulu, and the Asian Disaster Preparedness Center, Bangkok (more Asia oriented). As part of the East-West Center Pacific Islands Development Program's Disaster Preparedness Project, a detailed manual of disaster preparedness and response procedures and guidelines has been published (Carter, 1984).Table 1 and figure 1 show that the area with which this discussion deals is a highly fragmented island region, comprising many small, some minute, nations, both in land area and population. The social structure is predominantly rural, with the capital city often making up a small part of the total population and, in absolute terms, little more than a small town. Outside the administrative and governmental activities concentrated in the capitals, in most cases the indigenous inhabitants depend on subsistence agriculture or on usually a monocultural concentration on a cash crop, most frequently coconuts.

Jan 1, 1990

By Bourne R. W, Smith T

This paper presents initial findings of a project examining novel processes for the treatment of refractory sulphidic gold concentrates. Non-oxidative roasting of such concentrates for 12 hours at 750¦C resulted in the finely disseminated gold agglomerating to form discrete grains. The pyrite and arsenopyrite decomposed to form pyrrhotite, whilst the labile sulphur and arsenic driven off was collected on a condenser as a mixture of elemental sulphur, metallic arsenic and various arseneous sulphide compounds. As a result, the cyanide solubility of the gold contained in sulphidic refractory gold concentrate from the Emperor mine in Fiji improved from 54.5 per cent to 98.4 per cent; from the Fimiston mine in WA (65.2 per cent to 96.6 per cent), from the Windarra mine in WA (69.6 per cent to 91.3 per cent), from the Harbor Lights mine in WA (20.4 per cent to 60.7 per cent), and from the Wiluna mine in WA (12.6 per cent to 28.0 per cent). The non-oxidative roasting conditions have not been optimised for each of these minerals. Subjecting the non-oxidatively roasted minerals to mild oxidative acidic iron sulphate pressure leaching (with typical temperature of 100¦C and typical oxygen overpressure of 500 kPa) to remove iron and so further liberate finely disseminated gold, resulted in the cyanide solubility of the gold exceeding 96 per cent for each of these five concentrate types (including those from Harbor Lights and Wiluna). Thiourea leaching of the sulphur-rich residues under acidic conditions resulted in remarkably high gold extractions being achieved. These novel processing options need to be optimised, and their economic viability established.

Jan 1, 1991

By Fourney W. L, Dick R. D

A small-charge rapid excavation system employing a novel penetrating cone fracture initiation and propagation technique has been demonstrated to be capable of excavating the hardest of rocks at efficiencies (energy per unit volume of rock removed) four to ten times greater than attainable with conventional drill and blast. Significant enhancements to the concept developed during the research efforts include the use of propellant rather than explosive charges and a device for containing the charges and effectively sealing the shot-holes. The experimental results, including the excavation of several tons of hard rock in a research mine, have confirmed the novel breakage process and provided a data base for the design of a continuous hard rock mining machine based upon the concept. The small-charge excavation system would be attractive for civil construc-tion operations where sensitive structures, equipment and personnel would be in close proximity to the excavation face. The system would be attractive for selective mining operations where the ore rock could be fragment-ed and processed separately from the barren country rock. The barren rock could then be backfilled underground and eliminated from the traditional hauling and milling operations.

Jan 1, 1990

By Slechta JJ

The performance of a hydrocyclone treating fine coal has been examined over a wide range of feed and operating conditions.The results were expressed in terms of partition curves from which the water split to the oversize flowstream,the corrected separation size and reduced partition curves were determined-.The following conclusions were obtained. (a) The water split to the oversize flowstream was found to be dependent upon the vortex finder and spigot diameters of the cyclone and the flowrate and solids content of the feed slurry. (b) The corrected separation size was dependent on the solids content of the feed,and the vortex finder and spigot diameters.The hydraulic pressure (or flowrate) of the feed slurry did not have a significant effect.This phenomenon could be explained in terms of crowding of the particles at the Spigot.

Jan 1, 1984

By C Gypton

This paper gives some insights into what to look for when reviewing feasibility studies. The review by a third party is an important element of the risk management process and may be the last remaining opportunity to uncover errors, or identify and reduce project risks on paper before they are converted to financial disappointments, steel and concrete monuments to process failures or cost overruns. The mining industry has had a spotty record in the area of estimating initial capital costs and operational performance, even though the standard of feasibility studies is generally acknowledged to have improved in the last decades. Third party reviews rarely have the luxury of enough time and unlimited funds, so where should the reviewers focus their efforts to be most effective? Assuming that the project already apparently meets investment criteria, the authors suggest where and how to look among fundamental project parameters for signs that serious flaws exist that have the potential to become project killers. We also give advice on how to review cost estimates without becoming lost in the details. The paper is supported with numerous actual examples.

Jan 1, 2003

By Oliver R

The Hamersley Iron ore resources are geologically complex with fluctuations in mineral chemistry. From this resource Hamersley Iron must produce consistently high quality direct shipping products and have the ability to evaluate the effects of changes in demand. In order to achieve these objectives an incremental long term planning technique has been developed. This method reduces the total geological resource statement into a simple, logical sequence of events. A logical sequence of mining increments is defined within individual areas based on a final pit and access system. Increment characteristics are derived manually and from a computer based orebody model. The end product of the technique, an optimum mining schedule, is readily developed from the incremental information. Among its many benefits, this simple technique rapidly provides management with information for policy formulation.

Jan 1, 1979

By Gibson I, Somerville J

Three main confined aquifers occur in interseam sediments beneath the planned excavation for the Loy Yang Brown Coal Open Cut. Sub-artesian groundwater pressures occur in all aquifers necessitating dewatering to prevent excessive seepage and depressurisation to prevent heaving of the open cut floor and batter instability. Reduction of water pressures in coal joints is also required to maintain coal face stability. This paper describes the depressurization and dewatering strategies, investigation for and installation of pump bores and groundwater observation bores. Approximately 5000m of drilling is carried out annually for dewatering at Loy Yang and both cable tool and rotary flush drilling methods are utilized. The cabletool method is used to obtain accurate samples for laboratory analysis, whereas rotary flush methods are used for speed and for installation of the larger diameter pumping bores. A method of re-establishing pump bores after partial excavation during mine development has been successfully developed with large cost savings. Trials are also being conducted with pre-collaring of deep bores with rotary methods then sampling the aquifer strata with a cable tool rig.

Jan 1, 1988

By Davey FJ

The Hikurangi Margin of eastern North Island New Zealand represents the feather edge of the over-riding Indo-Australian Plate at its convergent boundary with the subducting Pacific Plate. Towards the south, convergence becomes slower and increasingly oblique, and sediment supply from the Southern Alps becomes increasingly rapid. In this environment a 150 km wide, imbricate thrust, accretionary prism has grown since the Miocene, uplifting slope ridges and basins and a range of coastal hills. Offscraping of thick, axially transported, trench-fill turbidites begins in a zone of proto- thrusts, which extends up to 25 km beyond the principle, slope-toe, deformation front. On the slope, landward tilted, trench-slope basins are separated by ridges. The ridges ride up on thrusts that sole out at a major decollement. The decollement dips landwards at 3 degrees to a depth of 14 km at the coast, where it coincides with an onshore zone of high seismicity. Beneath the decollement, about 1 km of consolidated, oceanic sediment is going under the margin with the underlying oceanic basement. Some of these sediments may underplate the frontal ranges to the west and geochemical evidence of subducted sediment is found in the volcanic zone beyond. A rapid decrease in the width of the accretionary prism to the north is associated with a decrease in sediment supply and perhaps with a dislocation in the downgoing plate. To the south, the accretionary prism narrows, swings westward, and merges into the zone of very oblique collision that marks the transform between mirror image subduction to north and south of New Zealand.

Jan 1, 1987

By Reid A. F

Since early 1971 Western Titanium N.L. has been operating an ilmenite upgrading plant on a commercial basis at Capel, Western Australia. In their process ilmenite is pre- oxidized, then reduced in a rotary kiln to a mixture of metallic iron and titanium oxides. The iron is leached out by accelerated rusting in aerated water, leaving a product with titanium content, expressed as Ti02, of about 92%. Samples from different stages of the up- grading process, representing operations over the last two years, have been studied in detail by X-ray diffraction methods, and the sequences of phases and reactions occurring have been determined. Quantitative X-ray studies showed the ilmenite feed materials to consist of a mixture of ilmenite and pseudo- rutile. Pre-oxidation of the ilmenite at =1000¦C leads to the formation of rutile plus a Fe2TiO5-FeTi205-Mn2TiO5 solid solution. The final reduction product consisted of a mixture of metallic iron, reduced rutile and a FeTi05-MnTi205-Ti305 solid solution. The relative amounts of these reduction products were very sensitive to the initial concentra- tions of the minor constituents manganese and magnesium. The effects of variation of ilmenite feed rate, reducing atmosphere,- reduction temperature and controlled addition of magnesium were also studied.

Jan 1, 1973

By Gallet M, Watsford R. M S

The 1989 feasibility study of the chessy, france, copper, zinc, pyrite and barite orebody was based upon a classical flowsheet. The flowsheet included, three stages of crushing, conventional rod and ball mill grinding in series, and sequential flotation of four products utilising conventional mechanical flotation cells. To improve the profitability of the project the partners commenced a search for ways to reduce the projected capital and operating costs of the proposed development. This paper presents the improvements in the projected capital and operating costs as a result of design and concept changes. The major changes included: ò the simplification of the crushing section with the adoption of semi autogenous grinding (SAG) milling of primary crushed ore. ò the deferral of pyrite and barite flotation circuits until market conditions were positive. ò the simplification of the flotation circuit by the use of column flotation cells for combined rougher/cleaner duty. ò the purchase of second hand equipment. The result of these changes was to reduce the capital cost estimate of the plant from US$ 21 million to US$ 11 million and operating cost estimates from US$ 18.90 to US$ 13.60 per tonne of ore for a decrease of approximately ten per cent in potential revenues.

Jan 1, 1991

By Watsford RMS, Wickham P

In October 1980 the two existing flotation circuits were combined into a single new circuit. This circuit used modern 11.3 m3 flotation cells which replaced 1.4 m3 units. Sometime after this change, a significant deterioration in metallurgical performance occurred. This paper describes the work done to discover the causes of deterioration in performance and actions taken. The program implemented to prevent a future occurrence is also presented. The work included analysis of routine plant data, analysis of surveys to obtain element and mineral flows on both a sized and unsized basis, some quantitative mineralogy, and analysis of some external factors.

Jan 1, 1978

The Mammoth Copper Deposit consists of three distinct orebodies adjacent to the Mammoth Fault. This fault is arcuate, changing from a normal tension fault to a shear strike fault just to the north of the mine. Movement on the fault was probably contemporaneous with deposit- ion of the adjacent sediments. In the upper levels the No. 1 orebody occurs within a brecciated zone in the footwall of the fault, but at depth the No. 2 and 3 orebodies are stratabound by two brecciated lithologic horiz- ons. The host rocks are impure sandstones, arkoces and quartzites, which in the mine area are near the top of the Lower Proterozoic Myally Beds. Overlying these beds is a conglom- erate siltstone sequence which has been assumed to be the base of the Gunpowder Creek Formation. North and south of the mine the conglomerate rests on an erosional unconformity representing a major time break, but in the mine the uncon- formity and conditions of deposition of the conglomerate are obscure. Some mineralization is contained within the conglomerates. The sulphides present are chalcocite, bornite, chalcopyrite and pyrite. Chalcocite is dominant in the upper levels but could be en- riched by supergene processes. At depth, bornite becomes the dominant copper sulphide with lesser amounts of chalcopyrite, pyrite and primary chalcocite. Throughout the orebody minor digenite and covellite occur and arsenic is a minor constituent bound up with the pyrite. The bulk of the sulphides occur in stringers, fractures and breccia interstices but finer grained primary bedded sulphides can be observed. The genesis is probably a complex process in- volving active tectonic movements extending from deposition to post lithification giving numerous phases of brecciation and redistribut- Ion.

Jan 1, 1974

By Biswas AK, Hayes P

During the reduction of iron oxide pellets in the blast furnace it has been found that catastrophic swelling (up to 300% volume increase) can occur. Although the burden preparation conditions can be designed to avoid this phenomenon the exact reason and mechanism of the swelling has yet to be clearly identified. Swelling of the burden is undesirable since it reduces the interparticulate voidage in the blast furnace thus reducing gas flow through the stack resulting in low production rates of iron. The present study differs significantly from previous experiments in that reduction is carried out on single crystals of wustite thus the problems of control of gas composition and specimen preparation are minimised. The microstructures formed on reduction have been examined by optical and scanning microscopy. Pure wustite and wustite doped with various levels of CaO have been examined after reduction in controlled CO-CO 2 gas mixtures at 968¦C. The catastrophic swelling on reduction coincides with the formation of an unusually open iron structure in which the iron appears as whiskers or needles as previously reported. The spacing and thickness of the needles are shown to vary with impurity content and gas composition. Metallographic examination has shown in addition, however, that the whiskers do not necessarily constitute the only product form of the iron produced and in CaO containing wustites with less than - 2% CaO there is a transition from needle growth to porous growth of iron. Thus the % swelling of the oxide particles is dependent on the initial size of the oxide grains. Samples of FeO - 10% CaO exhibited a previously unreported product inorphology associated with the nucleation of 2CaO.Fe203.

Jan 1, 1980

By Dunlop JSF

A description of general mining proced- ures and tyre maintenance practice is given with particular reference to tyre mainten- ance facilities and record keeping at Groote Eylandt. Experience with tyre wear on Wabco 85C rear dump trucks is then outlined, concen- trating on wheel camber, wheel alignment, truck speed, tyre pressure, loading and haul road design. T T.1TUnilhTPTTnAT The Groote Eylandt Mining Company Pty. Limited mines and beneficiates sedimentary manganese ores from a series of orebodies occurring in the western part of the island. The island is one of a group on the western side of the Gulf of Carpentaria, about 50 kilometres from the Arnhem Land coast and about 650 kilometres from Darwin. Whilst capacity of the mine is presently 2.3 mil- lion tonnes of product per annum, current production has been reduced to just more than half this figure, due to a general mar- ket recession.

Jan 1, 1982

By Dickson T. J

Slag cleaning is an important part of the pyrometallurgical operations at the Kalgoorlie Nickel Smelter. It is a complex system with many streams of different phases and composition. Some of these streams are very difficult to control and/or monitor. Through the use of a statistical computer package, called Minitab, key relationships affecting the economical operation of the slag cleaning process have been found. Data for the statistical analysis was collected from all possible variables around the appendage.

Jan 1, 1991

By M Chen, W S. Ng, Y Liu

In the processing of refractory gold-bearing sulfides, pressure oxidation (POX) is commonly known for its role in liberating the gold in solid-solution via oxidation of the sulfide occlusions. For deposits that contain arsenic-bearing species including arsenian pyrite and arsenopyrite, POX serves an important secondary function in the fixation of arsenic, via the hydrothermal precipitation of stable arsenates such as scorodite and basic ferric arsenate sulfate (BFAS). There have been various investigations on the impact of different POX conditions on arsenic precipitation and the stability of the formed phases, but less is known about the changes to the arsenic carrier that occur in the curing stage, which follows directly from POX. The primary function of curing is to coax the dissolution of sulfates to reduce lime consumptions during cyanide leaching, and the slurry is kept at elevated temperatures near 100°C to achieve this. While the arsenic-bearing phases are expected to undergo transformation during this stage, there has thus far been limited experimental evidence. In this study, the effect of curing time and curing temperature on the arsenic-bearing species and arsenic deportment in the POX product has been investigated. Leaching of the curing products was also conducted to examine the stability of the arsenic species in the solid precipitates.

Aug 24, 2022

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

Interpreted geologic domains provide the geologic architecture of many current models used to estimate the potential economic resources in mineral deposits. The spatial extent of each domain is usually defined by a three-dimensional wireframe or triangulated surface.The set of geologic wireframes forming part of a resource model might generally be called a spatial interpretation of some set of geologic features coincident with the mineralisation, based primarily on logged and mapped properties of the samples and other exposures of the mineralisation. The interpreted spatial distribution of rock type, alteration and grade of drill hole samples above a particular grade threshold are commonly used criteria in constructing the geologic domain wireframes. Frequently, the grade threshold is closely related to the anticipated economic cut-off grade. The boundaries or spatial limits of different domains are most commonly defined as æhardÆ or æsoftÆ. A æhardÆ boundary usually means no dependent relationship of any kind is defined between the properties of samples inside a particular domain wireframe and those samples outside the wireframe. A æsoftÆ boundary commonly implies that some kind of dependent relationship does prevail between the properties of samples inside and outside the particular wireframe. Many ways are used to describe those relationships, few of which are based on spatial analysis of the continuity of sample attributes across the domain boundaries. In local estimation procedures such as ordinary block kriging, æhardÆ boundaries act as a total barrier to the influence of samples on either side of the boundary depending on the location of the block being estimated. In some instances, æsemi-permeableÆ boundaries are used in which the samples inside a domain wireframe are allowed to influence the estimates outside but not the reverse. This can lead to many undesirable effects in estimates of block grades.This paper discusses the value of this approach to geologic domaining from a viewpoint of model complexity, as well as in relation to the implications for both linear and non-linear estimation methods and contrasts it with alternatives. It also explores some important consequences of using æhardÆ and æsoftÆ geological boundaries with the commonly used modelling methods: excessive smoothing of estimates near domain boundaries and conditionally biased estimates of grade at the global and local scale.

Sep 26, 2011

By Susanto A

As part of the current NERDDC funded project studying Dragline/Hopper/ Crusher/Conveyor systems for overburden removal, an investigation was carried out to assess the feasibility of automating the swing-to-dump phase of the dragline digging cycle in order to main- tain consistent performance of spotting the bucket above the hopper prior to dumping. The study involved design of automatic position controls for the hoist, drag and swing drives and simulation of detailed mathe- matical models of the three electromechanical systems and their associated electrical control schemes. The design of the hoist and drag systems to position the bucket in the boom plane is relatively straightforward. Simulation results show fast and accurate performance, with no evidence of interaction between the two drive systems through the ropes. The design of the swing position control system involves special strate- gies to cater for variable inertia and to damp the pendulum oscillations of the bucket. The use of a bucket pendulum model and variable dynamic compensation embedded within the feedback control loop, along with optimal speed/angle slowdown trajectories, has yielded fast and damped positioning responses under simulation.

Jan 1, 1989

By Schoning W. L

Ore deposit models form the basis for numerous other economic decisions in the mining process. The success of these economic decisions therefore depend directly on the accuracy of the ore evaluation process. The Geology Department at the Sishen Iron Ore Mine is responsible for the generation of a reliable geological computer model of the rock material with predicted grades. This information is then utilised for further ore reserve calculations, mine planning, production scheduling and grade control. Owing to a very complex geological orebody, grades and beneficiation characteristics differ significantly from sample to sample. This means that ore evaluation is a difficult process and great reliance is placed on computer techniques. In 1993, preparation for the ISO 9002 quality certification of the mine motivated the Geology Department to hold formal `problem solving' sessions in order to identify and revise problem areas in operating

Jan 1, 1995