Search Documents

An Environmental Impact Statement (EIS) for a major mining development typically has to address various aspects of surface water management, including some which generally tend to be the more contentious: the diversion of rivers and creeks from areas disturbed by mining, and their rehabilitation; the effective management of disturbed area run-off via the collection, containment and treatment of contaminated water on site in sedimentation dams; the collection, containment and treatment of mine pit water; the decommissioning of surface water storages; final void water quality; and water discharge criteria. Environmental Impact Assessment processes for proposed mining developments in Australia at the state and commonwealth level usually involve a form of Initial Advice Statement (or Notice of Intent), Terms of Reference, an EIS, and a Supplementary Report (or similar) which responds to agency and public comment on the EIS. The EIS is used by approval agencies to decide the acceptability of the Project, and to set the conditions of approval. The conditions are often in the form of a state-issued æOperational LicenceÆ or similar. With mining, the initial approval at the EIS stage is often just a pre-cursor to various other planning related approvals, including obtaining a mining lease. Afterwards, mine plans and plans of operations must be submitted to government at various stages of the mineÆs life, ostensibly to provide the detailed mine planning over periods of one û five years. Despite all this additional planning and documentation beyond the submission of the EIS, government approval agencies are increasingly not satisfied with conceptual water management designs and commitments to an outcome (such as meeting a specified water quality standard) in the EIS. Agencies are also requiring sufficient water management design information to be convinced that the outcomes are achievable. To assist proponents of major mining developments, the Queensland Government has published Technical Guidelines for water management, and Environment Australia has published a æBest Practice Environmental Management in MiningÆ booklet on water management. In addition, the Australian and New Zealand Environment and Conservation Council (ANZECC. 2000) has published Water Quality Guidelines which provide an approach to water management, and provide receiving water investigation trigger criteria. So, what are the water management issues that are likely to be the subject of comment, debate and negotiation prior to the EIS being approved? and what commitments may a mining proponent have to make in order to convince the approval agencies that sufficient investigation and design has been provided? This paper provides some answers to this question, by reference to recent major mining proposals which the author has managed through state and commonwealth Environmental Impact Assessment processes.

Jan 1, 2003

By J Cook, S Pike, D Pridmore

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The application of high-resolution seismic reflection to map structure and/or mineralisation in hard rock environments has progressed significantly in the last decade. Improvements in equipment, field practice, processing and understanding has seen the seismic reflection technique emerge as a cost-effective tool for high-resolution three-dimensional structural and lithology mapping to depths far greater and with superior accuracy than other more conventional geophysical techniques.This paper outlines results and preliminary interpretation of 2D and 3D seismic reflection surveys aimed at defining fault zones and locations for quartz load development in favourable host lithologies at the Cracow low-sulfidation epithermal gold system in Queensland, Australia.As this is possibly the first time that high-resolution seismic reflection data has been used to define the structurally-controlled location of low-sulfidation epithermal gold mineralisation, an important aspect of this work was the derisking or due diligence steps taken prior to commissioning the full 3D surveys at each site. This included full wave sonic logging, vertical seismic profiling and trial 2D lines. Interpretation of the 2D profiles and the drilling of interpreted structure provided the confidence to proceed with the full 3D survey.The advantage of collecting 3D data extends beyond ensuring that the received reflections are located correctly in 3D space. The final 3D data cube can potentially map the entire fault network, thus highlighting flexures and changes in orientation of the structures both vertically and along strike, which is an important aspect in the deposition of gold and for direct targeting.CITATION:Smith, R, Cook, J, Pike, S and Pridmore, D, 2015. Application of high-resolution seismic reflection surveys to exploration for blind vein systems at the Cracow low-sulfidation epithermal field, in Proceedings PACRIM 2015 Congress, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The use of scrapers in mining and earthmoving operations is not new; in fact they are one of the earliest methods of bulk earthmoving. A single machine, which can load, haul, and dump material with a minimum of ancillary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. Maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancillary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

By N Weatherstone

A consistent and reliable international approach to public reporting of a mining companyÆs main assets, its Mineral Resources and Mineral Reserves, has become of increasing importance in recent years with the rapid globalisation of the mining industry. Through the efforts of the Committee for Mineral Reserves International Reporting Standards (CRIRSCO), a committee representing national resource/reserve reporting committees in Australia, South Africa, UK/Ireland/Western Europe, Canada, USA and Chile, the reporting standards in most æwesternÆ countries use almost identical resource and reserve definitions and are generally around 90 - 95 per cent compatible. New codes based on the CRIRSCO model are being developed or considered in other countries, including Peru and the Philippines. This unified approach has provided the mining industry, regulators and investors with a common framework to report and interpret mineral resource and reserve estimates, thereby facilitating funding to the mining industry through improved investor understanding and confidence. The common reporting standards are reflected in the CRIRSCO International Template, available on CRIRSCOÆs web site, a document that is kept æliveÆ by reflecting the best of the most recently published CRIRSCO-type national standards. In a significant exception to this unified industry approach, the USA Securities and Exchange Commission (SEC) requires adherence to its own standard, only partly compatible with CRIRSCO-type standards, with adverse and costly implications for companies listed in the USA. A major industry submission was presented to SEC in April 2005 which, if accepted, would bring about considerable compatibility of CRIRSCO and SEC standards. The UN Economic Commission for Europe (UN-ECE) has, since 1992, been developing its Framework Classification (UNFC) as a single global system for harmonising all existing national and international resource/reserve reporting systems, covering both government and industry requirements and both the hydrocarbon and solid minerals sectors. While few mining companies report their resources and reserves using the UNFC, the system is accepted or is being examined as a basis for reporting by some governments, including those of Russia, China and India. The UN-ECE agreed in 1999 to incorporate CRIRSCO definitions into the UNFC for those categories of resources and reserves used for market-related reporting, but a more recent edition of the UNFC removed or changed the definitions, requiring re-engagement by CRIRSCO to ensure compatibility. Since 2005, CRIRSCO and the Society of Petroleum Engineers (SPE) have been involved in discussions with the International Accounting Standards Board (IASB), which plans to develop a new Accounting Standard for the Extractive Industries as part of its International Financial Reporting Standards. At the request of the IASB, CRIRSCO and SPE have been examining any potential for convergence of resource/reserve definitions between the mining and hydrocarbon industries. Each of these systems is described in this paper and high level comparisons made.

Jan 1, 2006

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

By J Williams

The recent drought has highlighted the finite nature of AustraliaÆs divertible water resources. According to AustraliaÆs recently completed National Land and Water Resources Audit, development of water resources in southern Australia has reached or exceeded sustainable extraction limits. Similarly, 161 out of 538 groundwater management units are either totally allocated or already over allocated. Whilst mining only uses about three per cent of diverted water resources, water scarcity may be a major factor that determines whether potential mines can be developed in the future. Furthermore, the development of extraction and processing facilities that limit water use and maximise the re-use the waste water streams will be even more fundamental features of the mining industry in the 21st century than they are at present. There are encouraging examples where innovative water re-use technologies are significantly reducing the water used per unit of mined product. Whilst mining in the areas of Australia draining to the tropical seas may be less constrained by a current lack of water (60 per cent of divertible water resources drain into the Timor Sea, Gulf of Carpentaria and north east Coral Sea), it is highly probable that there will be increasing demand for these waters from the irrigation industry, whilst pressure will also be applied to ensure that environmental flows that benefit the coastal fishing and prawn industries are maintained. In the Great Artesian Basin, current research is demonstrating that the groundwaters are being recharged at rates considerably lower than current extraction. Whilst some other groundwater basins in arid and semi-arid Australia have currently untapped resources, these water are often relatively saline and/or may be intimately linked with key ecosystems in discharge areas. This paper presents an overview of the current state of our water resources and examines some of the key water use issues including allocation, use and reuse, environmental flows and competing demands on the resource that will ensure that water issues remain high on the policy agenda for mining, irrigation and other water users.

Jan 1, 2003

The preferred alternatives in heap design and their motivation are identified as- -normal heap leaching, to be generally applied wherever possible, - flooded vat leaching, to be appliedwhere wetted ore lacks adequate cohesion or if limited space necessitates it,- thin layer leaching, to be applied where deleterious vat chemistry necessitates it.A number of the following features would probably be incorporated in the optimization of normal local heap leach operations- pre-cyanidation - pre-agglomeration - retaining walls- staged (counter-current) heap treatment- control of calcium levels- reduced pH and trickler irrigation

Jan 1, 1984

Chromite ores have a long history of low pricing and for AustraliaÆs only chromite mine this has been a particularly tough challenge, especially as the mine is located nearly 400 km from the nearest port at Port Hedland. A stockpile of chromite fines (-16 mm) has been built up since 2003. The opportunity to develop a facility to treat this material to produce a chip (-16 + 1 mm) product and a sands (-1 mm + 45 micron) product was taken when the price increased to above US$140/t. A simple add-on plant containing a heavy media cyclone circuit for the chips and a spiral circuit for the sands was designed and developed. During construction of the fines plant the price of chromite reached a level where the payback for the entire project was less than eight weeks. Soon afterwards the price and the demand for chromite plummeted and the site was put on care and maintenance, except for the commissioning of the fines plant. This put considerable pressure on whether to continue to operate the plant or to place it in care and maintenance. Times of boom and bust provide management with almost totally opposite views. By not taking a conservative view on prices and costs, the effect of extremely low prices and minimal demand can be devastating to a good project. Designing and building plants with conservative costings in boom times gives a greater chance of keeping projects alive during the bust periods that tend to follow.

Jan 1, 2009

By N TassT, J Cyr

At the East Sullivan site, wood wastes covering the abandoned mine tailings impoundment prevent sulfide oxidation by creating an anoxic environment. The addition of coarse ligneous wastes and their high permeability favour infiltration, resulting in a water table rise that maintains most tailings under water saturation and thus provides an additional protection against sulfide oxidation. Moreover, high infiltration allows a more rapid flushing of acid prone groundwater generated prior to the cover placement, which could cause acid mine drainage over a long period of time. Finally, the pore-waters under the cover are characterised by a strong reducing potential, high alkalinity, and near neutral pHs. These conditions favour sulfate reduction and base metal precipitation as sulfides and as carbonates. Pore-water composition monitored from 1992 to 1998 showed a significant Fe2+ decrease, following cover placement. Thereafter, the restoration strategy capitalised on the alkaline and reductive properties of the waters underlying the wood-waste cover. An original treatment of acid effluents, based on the recirculation of water discharging around the impoundment through the organic cover, was implemented. In 2002, the recirculated water from May to October had a mean pumping rate of 240 m3/h, for a total volume of 800 000 m3. Data gathered near the dispersal zone from 2000 to 2002 show that despite the recirculation of acid water (pH ÿ3), the pH decreases by only one unit from 7 to 6, during the recirculation period, ie from May to November. However, alkalinity decreases from 800 to 100 mg/L-CaCO3. Despite this decrease, the alkalinity is back up to 800 mg/L-CaCO3 the following May, thanks to sulfate reduction. From 2000 to 2002, Fe2+ concentration in the pore waters near the dispersal zone is maintained below 2 mg/L. Evolution of surface water quality suggests that the contaminated groundwater flush is completed in the north and north-west area of the impoundment; the east sector is under recovery, while the south sector remains the most problematic. A wood-waste cover, besides limiting sulfide oxidation, can fill the role of alkaline reducing barrier for the treatment of these acidogenic waters, until a balance between acidity and alkalinity in the effluent is reached.

Jan 1, 2003

By Lawrence M. J

It must be stressed that the following comments are offered only to assist mineral industry professionals in understanding the issues involved in personal liability. The information and views expressed herein are not intended to be a comprehensive guide or definitive statement of the law and they should not be regarded as a substitute for specific advice for individual situations. Readers should consult their own legal and other professional advisers before applying the content of this paper to their own particular circumstances. It is hardly news that work in the mining industry is governed by a complex regulatory and legal system which is constantly changing, but few realise just how directly they can be affected and become personally liable for any breaches. These may result in civil or criminal proceedings and personal assets are at risk. Owners, company directors, managers and now employees are at risk, together with consultants, contractors and suppliers of equipment or consumables, as well as government inspectors. They are liable for their personal decisions to act (or failure to act) in managing operations or carrying out directions, as well as for the actions of others under their control. This paper identifies the areas where such individuals in the open pit mining industry in Australia face the risk of personal liability and measures which can be used to minimise the risk or which can be used to make out a defence to legal action which could arise. There have always been a myriad of Commonwealth, State and Local Government laws and regulations with which to comply, and now international protocols are being used as a basis to impose greater obligations on all people. Once, the `corporate veil' gave some protection to the individual, but today there is negligible protection from the full force of the law. Not only are there various types of law enforcement officers, but public interest groups, shareholders, customers, suppliers, creditors etc may litigate. This paper is not intended to be an exhaustive discussion of the provisions of all the legislation or case law where individuals can be held) personally liable. These areas would include environmental, pollution and heritage law (including Aboriginal sacred sites); occupational health and safety (including workers' compensation) law; trade practices and fair trading law; contract law; corporations law (including the requirements of the Australian Stock Exchange [ASX] and Australian Securities Commission [ASC]); industrial relations law; anti-discrimination and sexual harassment law; taxation (including superannuation trustee) law; and the Common Law. The focus is on the following areas of regulation, which are outside the usual experience of those in the open pit mining industry (the Mining Acts and Regulations are specifically not dealt with here): ò Environment Law; ò Trade Practices Law; ò Occupational Health and Safety Law; and ò Corporations Law.

Jan 1, 1994

By J Zeni

In 2001, the Springvale Coal Mine determined a requirement for a 360 m deep vertical airway to ventilate ongoing underground longwall mining operations. The project, referred to as the Springvale No 3 Ventilation Shaft, was completed in 2003 - 2004 by blind boring a 4.25 m diameter hole from the surface to the coal seam at 360 m depth. The shaft was completed with a 3.5 m inside diameter lining made from a continuous watertight steel and concrete composite pipe. Presented from both the clientÆs and the contractorÆs perspective, the following paper describes the process of constructing a blind bored ventilation shaft for this application. Beginning with the clientÆs definition of the requirements and specifications for the shaft, the paper describes the steps followed by Springvale Coal prior to awarding the contract. Springv aleÆs process involved a thorough site investigation including procurement of geotechnical data for prospective contractors and the management of issues relating to safety, quality and the environment. The clientÆs view is followed by a description of the planning and works performed by their nominated shaft drilling contractor, Ardent Underground Pty Ltd.The contractorÆs description of the works includes the details of the blind shaft drilling and lining construction process used for this application. The design of the shaft lining installed at Springvale Coal was the first of its type to be used in Australia. The successful installation of a watertight composite shaft lining and the safety of the method, which did not require any personnel to enter the shaft or the mine, were among the positive outcomes from the project.

Jan 1, 2005

By Kagl J, Publlier M, Nekitel S, Arumba J, Rangin C, Mosusu N

Since the advent of plate tectonic modelling, the Ramu-Markham valley has been thought the site of a classical island-arc/conti- nent collision zone. In this interpretation the units south of the Markham Valley are held to be island are / micrcontinental mate- rial accreted to Australia and those north of the valley are thought to represent a separate Finisterre island-arc terrane. Recent remapping by the Geological Survey of Papua New Guinea shows: (1) there is no terrane boundary along the Ramu-Markham valley (2) the Finisterre Volcanics are probably part of either a fore-arc sequence or oceanic plateau obducted onto a microcontinent/ volcanic-arc composite terrane, accreted to the continental Australian plate. A new tectonic model is proposed for northern PNG and involves: (I) Eocene to Late Oligocene subduction below a microcontinent remote from Australia to produce the Sepik are and related intrusives, the Finisterre Volcanics (fore-arc or possible oce- anic plateau), together with the Alife blueschist. (2) obduction of the Sepik arc in Late Oligocene-Early Miocene times over the advancing Australian plate. This resulted in crustal melting, some of the products of which are the Mid- dle to Late Miocene Akuna and Bismarck intrusive complexes of the Maramuni arc. (3) obduction of the Finisterre Volcanics began in Early Pliocene times and continues today. (4) post-Middle Miocene mineralisation is the result of melting after obduction of the Sepik microcontinent.

Jan 1, 1997

The pyroclastic-filled Voorspoed kimberlite pipe has a low grade due to significant internal dilution which translates to a marginal business case. The site, with excavations, tailings dumps and buildings remnant of mining from 1906 to 1912 is to become De BeersÆ benchmark mine in South Africa. In a climate of skills shortages and lean structures, a geological service to optimise exploitation of this complex resource was established. As historical mining removed the higher-grade centre of the pipe, initial production was in the weathered upper benches along brecciated pipe margins. Trenching and blasthole logging before blasts helped to mitigate the effects of the drastic contact deviations that occur when working with an inferred geological model. However, identification of unfamiliar weathered kimberlite and delineation of unmodelled internal waste posed challenges. Efficient grade control by demarcation and allocation of individual truck loads will be vital to continue profitable mining at Voorspoed. Further challenges arose across disciplines. The first yearÆs planned production of mostly weathered kimberlite was processed through a plant designed for VoorspoedÆs unusually competent ore. The high clay content of the weathered material led to clogged chutes and overloaded fines disposal, hampering efforts to commission the plant. Resolving this problem involved mining æout of planÆ to provide a blend of fresh and weathered kimberlite. The calculation of an accurate mine call factor was hindered by a lack of haul truck monitoring, process stoppages and stockpiling in the plant during commissioning. Updating of the geological model to incorporate the contact changes observed in the pit was slowed by the need to first understand how 40 years of exploration data was integrated to create the model. A plan, involving focused mine geology practices, is in place to upgrade a portion of the resource from Inferred to Indicated level of confidence. These challenges are not limited to new mines but will be ongoing as new information is constantly gained at Voorspoed and many mining operations.

Jan 1, 2009

By Miyashita T, Yamamoto R, Kishimoto s

Following considerations of the effect of furnace size on pressure loss, pressure loss in front of tuyeres, gas flow in the lower parts of the furnace, the distribution of the burden and the gas flow in large blast furnaces is examined with particular reference to the burden distribution at the throat and the gas flow at high production rates. Improvement of gas flow is related to application of super-high top pressure and the use of moveable armour. A brief description of the NKK type moveable armour is given and its use in controlling the gas flow outlined. The operating results under controlled gas flow show an increase in production of Fukuyama No. 5 BF from 9,200 tpd to 11,000 tpd with a decrease in the fuel rate from 490 kg/thm to 460 kg/thm.

Jan 1, 1975

The need to estimate the block size distribution of a jointed rock mass is of great importance in the design of blasting rounds to attain a pre- established fragmentation. Other Geomechanics topics, such as ,hydraulic behavior of rock-masses, as well as the determination of their strength properties, also require the accurate prediction of a rock-mass composition in terms of block size taking in due account the three dimensional interference of joints and other geologic discontinuities. In this paper, a method for computing the block size analysis of a jointed rock mass is described, using as input the common geologic data (dip and strike) of fracture planes existing in a rock bench prior to blasting.

Jan 1, 1977

By Andrews JRG

Chrysotile asbestos is a valuable resource. Used as a reinforcement in asbestos cement, products are obtained which are cheap, are not attacked by vermin, do not rot or support growth of fungi and are unaffected by water or humid conditions. Such products are of great value in the developing countries where inexpensive and durable building materials and pressure pipe are very important to development, housing and water supplies. Concern over the adverse effects of inhaling asbestos has led to the introduction of increasingly stringent controls world wide on the quantities of airborne asbestos per- missible in the occupational situation. Wet processing has the potential for virtually eliminating the environmental concerns with asbestos dust both in fibre production and in the materials handling section of the manufac- ture of asbestos cement products. In addition, high efficiencies associated with wet process- ing mean that better yields are obtained and that the tailings which are dumped have a lower residual asbestos content. Since early 1977, ICI Australia and Woodsreef Mines have been engaged in a programme of research to develop and evaluate a wet mill- ingprocess to produce, from ore and existing tailings, high grade fibre suitable for use in asbestos cement products. The process has been developed through microscopic studies, labora- tory bench scale experiments, work in a small scale semi-continuous plant and product evalua- tion on experimental size Hatschek asbestos cement machines. A prototype mill with a normal feed rate of 1z tonnes per hour and capable of producing pipe grade asbestos from Woodsreef ore has been constructed and was operational from January, 1982 to July, 1983. A range of asbestos cement products have been made successfully on full scale Hatschek machines using fibre from ore and tailings milled in the prototype mill. Economic evaluations indicate that a wet process mill would be cheaper to build, operate and maintain than an equivalent dry process plant. A commercial plant has been designed 1. Manager New Process Development, Woodsreef Mines Limited, Barraba, Australia. 2. Senior Lecturer, Department of Chemical Engineering, Monash University, Vic, Australia. formerly Senior Research Officer, Research Department, ICI Australia Limited

Jan 1, 1986

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

By G W. Wilson

Rehabilitation of tailings impoundments is one of the most challenging aspects in mine closure, as not only does the potential for producing leachate pose a challenge to the rehabilitation designer, but also other aspects such as stability and settlement must be considered. The water balance of a tailings impoundment is unique in the sense that it usually hosts a pond that in turn causes a phreatic surface in the impoundment. The position of the phreatic surface defines the saturated and unsaturated zones in the impoundment, which of course varies spatially and temporally. Predictive modelling for this hydrologic system becomes difficult, as numerical models capable of analysing the combined saturated/unsaturated zones are not adequately refined to accurately solve the flux boundary problem for infiltration at the surface of the tailings. This paper describes the development of a flux boundary model that enabled accurate modelling of the unsaturated zone in the tailings impoundment at Kidston Gold Mine, Queensland, Australia. The technique made it possible to accurately predict the spatial variation of infiltration to the tailings as a result of the presence of the phreatic table. The conceptual model defines the boundaries for the Kidston tailings dam, based on a generalised cross-section through the dam. Firstly the shape of the top boundary is described as a function of the particle size of the tailings associated with particle segregation that occurs due to the hydraulic placement of tailings. This function was rigorously tested using in situ infiltration tests and laboratory materials testing. Defining the bottom boundary of the section, ie the phreatic level was done by physically monitoring the phreatic level with 42 piezometers strategically located on the tailings dam. Analysis of this data led to the fixing of this bottom boundary through the introduction of a function that mimicked the shape of the phreatic level. The material properties of the surface layer, specifically the saturated permeability that would govern the infiltration/exfiltration rates of moisture through the top boundary layer were defined on the basis of extensive field and laboratory material testing. A function for the saturated permeability was developed on the principles of particle segregation. Finally a procedure is described for the application of the new conceptual model for the evaluation of the spatial infiltration to a tailings surface using the rigorous one dimensional surface flux boundary code SoilCover. The solution of the calculation described above was then used as the top boundary condition in conventional three dimensional saturated/ unsaturated flow codes, and verified against measured seepage rates from the tailings impoundment under drains. It was concluded that the developed spatial flux function was in deed a most rigorous representation of reality. Although the methodology presented here was applied to the Kidston tailings impoundment only, the authors believe that the principles are directly transferable to any tailings impoundment that has a varying phreatic zone thickness due to the presence of a pond. The mathematical equations describing the typical cross-section would be site specific, but the approach and ultimate solution methodology would be directly transferable.

Jan 1, 2003

By V P. Beskrovnaya

Tests for the development of a metals recovery technology from samples of a Russian gold-bismuth deposit were carried out. Gold, silver and bismuth assay reported 5.6 g/t, 3.0 g/t and 0.08 per cent, respectively. Two flow sheet options were pilot plant tested: gravity/cyanidation of gravity tailings with subsequent flotation of cyanidation/carbon-in-pulp (CIP) tailings, and gravity/flotation concentration with cyanidation/CIP of concentrates. Option 1 results showed lower gold, silver and bismuth recoveries (81.3 per cent Au, 55 per cent Ag and 74.0 per cent Bi) due to low flotation efficiency for cyanidation tailings. Therefore, a flow sheet involving gravity/flotation concentration to produce bismuth-gold concentrates (0.8 per cent Bi) with subsequent cyanidation/CIP was recommended. Gold, silver and bismuth recoveries obtained by this method to the combined gravity/flotation concentrate were 90.2 per cent Au, 83.3 per cent Ag and 80.2 per cent Bi of the ore, respectively. Overall gold, silver and bismuth recoveries were 83.0 per cent Au, 40.5 per cent Ag and 80.2 per cent Bi, respectively. Gold and silver recoveries to the cathode precipitate were 92 per cent Au and 48.6 per cent Ag (per operation). Reagents consumed for flotation were 0.1 kg lead acetate/t ore, 0.4 kg butyl xanthate/t ore, 0.2 kg T-80 frother/t ore, 0.02 kg sodium hexametaphosphate/t ore, 0.15 kg copper sulfate/t ore. Reagents consumption for cyanidation was 0.42 - 0.48 kg NaCN/t ore and 0.2 kg CaO/t ore. It was recommended to deliver bismuth concentrates after hydrometallurgical treatment to a smelter. Overall bismuth recovery including bismuth recovery achieved by pyrometallurgy was 60.0 per cent. However, it was obvious that delivery of bismuth concentrates to a smelter and their commercial treatment would be very expensive due to relatively high mass pull of bismuth concentrates (7.6 per cent of the ore weight). For this reason, thiourea leaching and hydrochloric acid leaching with subsequent cyanidation/CIP were investigated as alternatives to cyanide leaching. These two alternatives were proposed to enable optimal recovery of valuable metals from concentrates on-site. Recoveries obtained by thiourea leaching were 91.2 per cent Au, 90.5 - 91.9 per cent Bi and 77.0 - 78.1 per cent Ag. However, that method required considerable capital and operating costs. As an alternative, hydrochloric acid leaching with subsequent cyanidation was investigated. Test results showed improved gold, bismuth and silver recoveries, which were 94 - 95.9 Au per cent, 94 - 96 Bi per cent and 76 - 78 Ag per cent, respectively. Hydrochloric acid consumption was 100 kg/t concentrate or 7.6 kg/t ore. Current efficiency during electrowinning was about eight to 12 per cent. A recommended flow sheet involving hydrochloric acid leaching of concentrates, electrowinning of bismuth from solutions, recycling solutions after electrowinning and cyanidation of hydrochloric acid leaching cakes is described. Overall recoveries achieved by the proposed flow sheet were as follows: 84.8 - 86.5 Au per cent, 75.8 - 76.9 Bi per cent and 63.2 - 64.9 Ag per cent. Based on results from these tests, initial data for a bankable feasibility study and plant designing were developed.

Jan 1, 2007

By Sims D. A

This paper primarily describes the application of geology to the different mining methods employed in a large underground mine. The steeply dipping stratiform Silver/Lead/Zinc mineralisation at Mount Isa include up to 28 mineable orebodies. The orebodiea are mined by cut and fill, sublevel benching and sublevel open stoping; the method chosen depending mainly on orebody geomechanics.The sources and methods of data collection, and the interpretation process undertaken, are described. The paper emphasises the different geological input required, by each individual mining method, to provide the necessary production and strata control. This input contributes significantly to the success and efficiency of the operations.

Jan 1, 1990