Search Documents

By Benson R. P

Building a new tunnel to accommodate CN North America's needs or double stacked container traffic for the next 100 years represents new and unprecedented challenges. Innovative approaches to contracting, especially the Negotiated Compressed Process (NCP), TBM design, project management, and the regulatory and approval process, were all required to deliver a new tunnel to meet the needs of CN North America within the approved completion schedule of 33 months compared to a traditional approach of 45 to 48 months. The NCP resulted in trimming a full 12 months from the project schedule with an anticipated saving of direct and indirect costs.

Jan 1, 1993

Key blocks occur on the surface of excavations and on the walls of the ornamental stones and limestone quarries due to the formation of joint planes, fissures, microfaults and quarrying operations. Movements of these key blocks have produced numerous important failures and are responsible for routine overbreak and rock falls accounting for great costs. The thrust of this work is to demonstrate how to delimit zones of poten- tial key blocks (danger zones) in the wall of Bani-Khalid quarry of lime- stone by using the block theory technique (stereographic projection). The final result of this study indicated that, there are three potential key blocks, the most critical one has been determined. To treat the problem, we sug- gest either to provide timely support to prevent the movement of this block, or to analyze it further in hopes that available friction on the faces will hold it safely in place.

Jan 1, 1989

By P Crorkan

Within the framework in which future exploitations for Codelco-Chile Divisi=n El Teniente are situated, regarding the deepening of its reserves and the geotechnical problems that affect their recovery, it becomes strategic to evolve with new variants, which make deep mining possible. Codelco ChileÆs Divisi=n El Teniente is progressing within its long-term planning the exploitation of a sector called Esmeralda, which includes its removal through the gravitational caving method (panel caving). It is planned to use pre-caving, which basically consists of developing and undermining the undercut level, without having developed the infrastructure of the production and transport levels. This is carried out in order to achieve a better redistribution of the stresses, thus obtaining higher quality in the infrastructure development of these levels as well as less risk. The extraction reserves for this area, estimated through the opportunity cost selection criteria, were determined at 348 million tons with an average grade of 1.014 per cent Cu. The project carried out geological and geotechnical studies in order to prevent the geomechanical risks of the sector to be exploited, which is a site conformed totally by primary ore. Lithologically, it occurs mainly in Andesite, located at the western limit by Brecha Braden Pipe. There are also varieties of porphyries and hydrothermal breaches of anhydrite. The Esmeralda Mine production program will increase from 4000 tpd (average) in 1998 to its 45 000 tpd rate of production estimated for the year 2005. The approved investment for the period 1995 to 1999 is $US 150 million, out of a total $US 213 million for the project. At feasibility study level and before the project, it showed a Net Present Value of $US 342 million, an Internal Rate of Return of 37 per cent and an IVAN indicator of 2.3 for a ten per cent discount rate and a copper price of 100 US cents/lb.

Jan 1, 2000

By Jepsen L, Gifford M, Thomas G. S

Mine planning requires careful prediction of both the head grade and tonnage of mineralisation. As part of the planning process, operators of the Murrin Murrin nickel/cobalt orebodies (located in the Eastern Goldfields province of the Yilgarn

Jan 1, 1998

This paper introduces a classification of gold orebodies, and comments on the importance of cutting high grade values, the choice of an appropriate ore reserve method and the necessity for producing recoverable ore reserves by considering the mining policy. The author stresses the importance of obtaining the appropriate information from the data relevant to a particular deposit as opposed to transfering parameters from one deposit to another.

Jan 1, 1987

By L C. P J Fonteneau, B Godel, E R. Ramanaidou

The Hamersley Province in Western Australia hosts large iron ore deposits. Each deposit displays various iron ore types that were defined on their metallurgical properties, especially in terms of porosity and mineralogy. Conventional porosity and mineralogy information on iron ore types are provided on 2D thin sections using automated image analysis with scanning electron microscopy (SEM)-based techniques combined with chemical analyses. However these techniques cannot accurately quantify the 3D porosity. High-resolution X-ray computed tomography (HRXCT) is a non-destructive technique providing a 3D image of the sample with a resolution close to 0.5 - 0.7 ¦m for samples size of up to few centimetres in length. 3D image analysis using customised algorithms now provide accurate quantitative porosity and mineralogy of iron ore types.CITATION:Fonteneau, L C P J, Godel, B and Ramanaidou, E R, 2013. Application of high-resolution x-ray computed tomography to iron ore characterisation, in Proceedings Iron Ore 2013 , pp 243-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The paper describes a computer model developed within the State Electricity Commis- sion of Victoria for use in open cut planning. The purpose of the model is to simulate all the typical occurrences in, and influences on, the coal supply and overburden disposal systems in order to be able to assess their performance. The model incorporates much of the long term and day-to-day operations planning logic required for the allocation of resources within an open cut. This logic takes account of power station demands, bunker stocks, plant and crew availability, the balance of reserves between dredgers, planned maintenance, etc. The perfor- mance of plant within the system is simulated using random selections from statistical distri- butions of Time to Failure and Time of Failure for each plant item. The application of the model in selecting a suitable bunker capacity in a notional open cut development is described to illustrate the potential of the model in optimising plant selection.

Jan 1, 1982

The screening of iron ores, sinter and coke, and investigations undertaken to improve screening efficiency and cloth life are discussed. The major modifications to coke screening proposed with the construction of No. 7 coke ovens battery are briefly described. The major problem areas were identified as screen cloth blinding and pegging, feed presentation and screen overloading. Blinding and pegging have had a significant effect upon screening efficiency with the screening of sinter, coke breeze and wet iron ores in particular. Pegging can be reduced or eliminated by the correct selection of aperture size and shape, screen excitation and slope, and screening medium. Blinding encountered with wet coke breeze was a particular problem in which no significant progress was made.

Jan 1, 1984

By Fukuda M, Kurita K

A mathematical model for estimating the liquid level in the hearth is presented. The analytical result was checked on a cold two-dimensional model and an additional boundary condition for the fundamental equation resulted. The applicability of the resultant equation was investigated on a cold model and a regression equation obtained for the average liquid level for Kashima No. 1 BF. Comparison of calculated and observed results were in fairly good agreement. It is concluded that the liquid level in the commercial furnace can be calculated from the measured values of pressure in the bosh and operating conditions.

Jan 1, 1975

By D J. Williams, S Islam

Fine-grained coal tailings slurry undergoes only limited settling and self-weight consolidation, and tends to remain slurry-like and unsuitable for conventional laboratory consolidation testing. In addition, constant rate of loading consolidation testing is more representative of the continuous disposal of tailings slurry into a tailings storage facility (TSF) than conventional step loading. The laboratory consolidation testing of coal tailings slurry under a constant rate of loading has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. In the slurry consolidometer, the rate of loading may be varied to represent the actual rate of rise of the tailings in the TSF. A slow rate of loading increases the test duration, while too fast a rate of loading may build up very high excess PWP, without achieving significant consolidation. For the particular fine-grained coal tailings slurry tested, the rate of loading in the slurry consolidometer is varied to access its effect on the development and dissipation of excess PWP. The resulting consolidation parameters are evaluated and explained using the recorded settlement and PWP data.CITATION:Islam, S and Williams, D J, 2018. Optimisation of constant rate of loading slurry consolidometer testing of fine-grained coal tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 72–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

The Honeymoon Well nickel sulphide deposits are located in the Agnew-Wiluna greenstone belt, about 45 km south of Wiluna. Both disseminated and massive sulphide nickel deposits are hosted by komatiitic rocks within the deformed and metamorphosed Honeymoon Well ultramafic complex. Fresh ultramafic bedrock is covered by up to 50 m of highly conductive transported material which greatly hampers both exploration and understanding of the bedrock geology. In the early-1970s, mineralisation was discovered by diamond drilling geochemical anomalies defined by wide-spaced percussion drilling over ultramafics that had been outlined by ground magnetics. Subsequent drilling has defined a resource of 158 Mt at 0.71 per cent nickel (based on 0.4 per cent nickel cut-off, 300 m below surface, December 1995) in four deposits. Over the life of the project a wide range of geophysical techniques have been used including airborne and ground magnetics, time domain clectromagnetics (EM), induced polarisation (IP)/resistivity, gravity and downhole techniques including EM, IP and physical property Measurements.

Jan 1, 1996

By Qi P. H

Gold dissolution can be achieved with a number of complexing ligands, all with varying degrees of stability. Processes based on the use of halogens have been known for many years. Beside providing the necessary complex- ing role, the halogens under the appropriate conditions are very effective oxidants for gold. Of the halogens, the gold iodide complexes are the most stable in aqueous solution. Iodine can establish the desired oxidation poten- tial for oxidizing gold, and unlike chlorine and bromine, the oxidizing potential of iodine is mild enough to avoid the oxidation of impurity constituents like metal sulfides. A series of experiments to investigate the fundamental electrochemistry of gold in different halide solutions was performed. Cyclic voltammograms of gold in the presence of 10-2 M chloride, bromide and iodide, respectively show that for a given potential the rate of oxidation is much faster in iodide solution than in either chloride or bromide. An overlay of linear sweep voltammograms for the anodic oxidation of gold in iodide and the cathodic reduction of iodine species on gold provides an effective method for examining the dissolution of gold in iodideftodine solution. The dissolution rates obtained from both electrochemical and actual leaching results are compared. Optimum leaching conditions are analyzed in terms of the iodide/iodine concentrations. Conceptual processes for the recovery of gold and iodide and the regeneration of iodine are discussed.

Jan 1, 1991

Studies of Theological effects in grinding hold promise for improving this energy-intensive process. Six surveys of the Hellyer ball mill were conducted. The stream and sizing data from these surveys were balanced by JKMbal to compare the mill

Jan 1, 1994

Pyrrhotite is the predominant gangue mineral at Renison comprising about 60 percent of the sulphides in an average ore blend. It exists as two crystal structures - monoclinic and hexagonal. Monoclinic pyrrhotite is the slowest floating of all minerals but is ferromagnetic and hence recoverable more efficiently by low intensity magnetic wet drum separators than flotation. This paper discusses the installation and commissioning of four 0.915 m x 3.0 m, 0.1 Tesla permanent magnet, wet drum separators prior to sulphide roughing flotation. Planned circuit and process control modifications to better accommodate magnetic separation into Renison's flowsheet will be Discussed.

Jan 1, 1991

The research, development and testing of a Blast Control Plug (U.S. Pat. #4,754,705) funded by the U.S. Department of Energy is described. The plug's function is to improve blasting efficiency through the enhancement of stemming effectiveness and thereby reduce drilling and blasting costs. The plug comprises a solid unit placed in the blast hole within the stemming column above the explosive. It is designed for use with back filled drill cuttings or any other suitable material The research and development program comprised the testing of the plug in small diameter holes in competent rock for both bench and crater blasting configurations and full scale field trials in multiple hole and row blasts using blast holes of from 76 to 387 mm in diameter. Test measurements included stemming displacement and velocity, face movement and extent, peak air over pressure and ground surface peak particle velocity. Data acquisition equipment included a Spin Physics SP2000 high speed video motion analysis system, and acoustic and seismic monitoring units. Substantial reductions in stemming ejection velocity or ejection elimination were achieved whilst reducing stemming length by up to 35% over conventional practice. Peak air blast pressures were also reduced by between 8 and 25 dB. A strong inverse relationship between rock face movement and stemming ejection velocity was found. The implications of the importance of stemming effectiveness in blasting and computer blast simulation is also addressed.

Jan 1, 1990

By M M. Hilden, M S. Powell, B Foggiatto

In an environment of decreasing ore grade, increasing costs and uncertainty with respect to commodity prices, the industry could benefit from evaluating alternative technologies and innovative circuit configurations. The flexible circuit approach suggests that the design of grinding circuits can be adapted to changes in feed properties and economic conditions. Advances in modelling and simulation are enabling metallurgists to predict the performance of more complex circuit configurations with increased confidence. Ore variability information and processing costs may be used as modelling inputs to determine the optimum processing conditions at a given time. A case study has been completed demonstrating the value of combining a flexible circuit with a model-based optimisation of the process. Ore properties and equipment performance data obtained in operating plants have been used to model and simulate flexible circuit configurations.This paper explores strategies to introduce flexibility to existing circuit configurations when processing ores with high variability. Multicomponent models incorporated in the model developers’ kit (MDK) allow the simulation of more complex and flexible circuits. This capability enables demonstration of the potential to enhance metal production through adapting processing routes according to the ore type being processed. The simulation of different flow sheet configurations allowed the definition of the best option for maintaining the metal production when treating lower grade ores, highlighting the advantages of flexible circuit configurations compared with a one-process-fits-all approach.CITATION:Foggiatto, B, Hilden, M M and Powell, M S, 2014. Advances in the simulation of flexible circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 391–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Most orebodies have one or more boundaries which are gradational, where the decision to stop mining is based on an economic cut-off. To maximise profit, this cut-off grade must be chosen correctly. It is necessary to review cut-off grades regularly, as the optimum cut-off grade changes with time, and major changes are hard to implement in a working mine without disruption to production schedules.Whenever a cut-off grade is used, there will be errors in its application caused by errors in the estimation of block grade. These can be minimised by stringent quality control in sampling and by the use of kriging, which attempts to minimise the absolute errors in grade estimation. The kriging method used should produce the most accurate estimates of marginal grade blocks - this will not necessarily be the technique that gives the best overall prediction of head grades.

Jan 1, 1993

By T Raynlyn, S Hapugoda, V Nunna

The predominant phase in most Marra Mamba, channel iron deposits and detrital iron ore deposits is goethite. Goethite abundant iron ore fines tend to have complex mineralogical associations and fine dissemination of gangue material. These ores are typically challenging to process using conventional beneficiation methods. With declining ore grades, there is a need to develop new processing routes for low-grade goethitic ores/fines.Comparative process amenability studies were carried out using two different processing options to recover iron with low alumina and silica content from a low-grade goethite-abundant iron ore fines (-2 mm) sample from the Pilbara region of Western Australia. The first option involved dehydroxylation at 350°C and 400°C, followed by grinding dehydroxylated samples to 100 per cent passing 106 µm and magnetic separation. The second option was processing raw sample by gravity separation using a Floatex density separator. The performances of the two processes are discussed in terms of the iron grade-recovery responses, and an optimal processing route is proposed based on the findings from these tests.CITATION:Nunna, V, Hapugoda, S and Raynlyn, T, 2015. Process amenability studies on goethite-abundant iron ore fines, in Proceedings Iron Ore 2015, pp 165–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Kikuta K

ISP (Imperial Smelting Process) produces zinc and lead simultaneously from zinc and lead sulphide concentrates and recovers copper and precious metals into a lead bullion. The strength of sinter is important to keep permeability in the shaft of the Imperial Smleting Furnace. The residual sulphur content of the sinter is also important as it causes metal losses into slag. The paper describes an investigation into the sintering operations to improve sulphur elimination and sinter strength. The micro structure of the sinter and the effect of the blast rate, sintering temperature etc have been studied.

Jan 1, 1993

By J Naude

The TauTona (Sotho for Great Lion) Mine near Carletonville, which is one of AngloGold AshantiÆs most profitable operations in South Africa, has started a multi-million dollar expansion project that is expected to extend the operational life of the mine by at least three years. The project will also secure some 1900 jobs for existing workers and contract workers. The $US140 million project entails the development of the orebody to a record depth of almost 4 km underground. It means that TauTona, which already mines gold at the deepest levels in the world, will deepen its mining activities from 3600 m to a new record depth of 3910 m. There is great anticipation about the expansion program, especially because of new technology that will contribute to a safer working environment. It includes a simplified hoisting system that will minimise safety risks in conveyance activities. Due to the unique nature of this project, depth below surface and working through a three-tier shaft system, various innovative measures were incorporated into the planning of the endeavour. Special support equipment was designed to reduce cycle times and enable the crews to install the extensive support, prescribed by the mineÆs rock engineering department, right up to the face before every blast. Both declines dip at 23¦. The personnel/material (P/M) shaft is 4.4 m wide x 3.9 m high. This shaft is unique in that the conveyance will have an onboard driver. The rock shaft is 4.5 m wide x 3.6 m high. Rock will be hoisted with two, ten-tonne overturning skips. In both cases, P/M and rock, the winders were designed for the highest duty cycle, which is encountered during sinking.

Jan 1, 2005