Search Documents

By D Howe, J Conn, J G. McLellan, K Gates

The Red October Gold Mine, owned by Saracen Gold Mines Pty Ltd, is located approximately 80 km south of Laverton, Western Australia. It is considered to be of a similar nature to many of the Archaean granite-greenstone deposits in the Laverton Tectonic Zone, and presents as an intriguing and relatively young deposit in terms of developed structural and genetic models. Regional deformation events have been proposed for the area, and are relatively well accepted. The most important of these deformation events in the region were the D4b (WNW–ESE sinistral transpression) and D5 (ENE–WSW dextral transpression) which have been attributed to the main Au mineralising phases. At the local scale there appears to have been a rotation of the regional stress field to provide the optimum orientation of maximum principal stress for sinistral movement on the main shear zone.Fully coupled 3D finite element analysis (FEA) was used to simulate the geomechanical response of the system based on structural observations. The geomechanical modelling resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two main deformation events. The D4 simulation provided a good correlation with the known distribution of subsidiary structures on the main shear zone, and furthermore provided several geomechanical targets that suggested locations of additional subsidiary structures. The D5 simulation provided a great insight into the response of the main shear zone and known subsidiary structures also highlighting additional targets indicating potential for further mineralisation. These targets have since been followed up with a 732 m deep surface reverse circulation (RC) drill hole, resulting in the discovery of two high-grade shoots, with follow up testing currently planned for mid-2014.CITATION:McLellan, J G, Conn, J, Howe, D and Gates, K, 2014. Structural controls and strain partitioning in the Red October Gold Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By S Bouzalakos, W Timms, H Malli

Combining ultramafic mine tailings and acidic mine drainage via mineral carbonation to sequester carbon dioxide, presents an opportunity to minimise waste on mine sites. Low pH mine water with trace element concentrations can be effectively treated by high magnesium mine tailings, a useful source of finely ground reactive matrix. By using milled tailings for mineral carbonation, there are negligible energy requirements for communition of ore rocks to reduce particle size. This study aimed to assess the technical applicability of reacting ultramafic tailings and acidic mine water through mineral carbonation technology in the mining industry. Dissolution has been identified as the rate limiting stage in mineral carbonation; hence the study focused on identifying optimal dissolution conditions. Ultramafic tailings (particle size <100 µm) derived from serpentinite ore, were reacted with a typical mine water that was synthesised in the laboratory. Through variances in the solid to liquid ratios and temperature of dissolution, a maximum five per cent magnesium dissolution efficiency was reached at 50 g/L and 100°C. The acidic mine water was neutralised (from pH <2 to pH ~6) and iron, copper and zinc ion concentrations reduced significantly during the formation of solid precipitates. Carbonation was undertaken by injecting carbon dioxide into the magnesium-rich solution to form stable carbonates. The experimental work demonstrated proof of concept; however, dissolution efficiency and carbon dioxide sequestration was low, indicating that further research would be required before larger scale implementation.CITATION:Malli, H, Bouzalakos, S and Timms, W, 2015. Ultramafic mine tailings to treat acidic mine water and lock away carbon through mineral carbonation, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 133–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

RME has a vision for a new mill operational paradigm made possible by RMEÆs fast, safe Mill Relining System. This vision can be moved forward into reality at any time with or without guidance from recent development in measurement and predictive modelling tools.Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by optimising liners for life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to design new liners for maximum commercial performance. This may mean more frequent changes of liners but with liners designed to yield optimum grinding, metallurgical and profitability performance. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. This paper provides an update regarding RMEÆs fast, safe Mill Relining System technologies and outlines RMEÆs vision of a æliner profile versus profitabilityÆ model as a function of metal price, developed intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2006

By G Fahey, S Rose

"Mining geology as a defined profession is only about 100 years old. The successful modern mine geologist needs to be a multidisciplinarian, but also needs to maintain a focus on the key outputs of the role. The technical skills needed in the role have increased as mining methods move to increasingly mechanised techniques. As well as being the guardian of the orebody and ensuring minimal dilution to expected ore grades, the mine geologist should be competent in the 12-point mine geology process. The mine geology process should include:a statement of purpose (a ‘mission statement’)geological mapping/logging system that supports consistent and regular geological data collection, storage, and interpretationsampling system that can produce representative samples and fits in with the mining scheduleassay database with relevant controls to ensure only ‘clean’ data is loadedsimple quality assurance / quality control (QA/QC) system for samples and assays, with a response process to react to out of specification resultsconsistent method of exporting, visualising, processing and interpreting assay data to create mining blocksdevelopment sign-off system so that all development and stoping is controlledproduction tracking system to monitoring and reporting what ore and waste volumes have been moved from the face, to any intermediate stockpiles, the run-of-mine (ROM) pad and into the crusherreporting system for daily, weekly and monthly reporting of tonnes and gradesdocumentation so that the grade control system has simple, but effective descriptions of how it works, who has responsibilities, and authorities, and be easily maintainedreconciliation system to compare resource and reserve to grade control and to mined and milledtraining system so that the geology team can quickly become competent.In this paper, the authors discuss the requirements of each point, and comment on common shortfalls observed by them over several years’ experience on producing mines worldwide.CITATION:Rose, S and Fahey, G, 2014. Modern mining geology, in Proceedings Ninth International Mining Geology Conference 2014 , pp 461–466 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

With the iron ore industry in Australia producing hundreds of millions of tonnes of ore per annum, the associated costs of these operations extend into the billions. It is no surprise in the current economic climate that more and more companies are looking into different ways of optimizing their costs to keep their sites operational. One way of improving operations is the use of electronic initiating systems like i-kon and Uni tronic detonators. These systems have been used around the world to improve current practices and optimize drill and blast costs. However, these systems have yet to make an impact upon the iron ore sector in Australia. Some of the potential improvements include:pattern expansion and a subsequent reduction in drilling and explosive costs;improved fragmentation and hence increased dig rates, thereby driving $/tonne down;embracing the 'mine-to-mill' concept by reducing the downstream costs of crushing and milling;improving the overall condition of pit walls and floors, leading to a safer working environment in which optimal haulage performance can be achieved; and improvements in vibration management around heritage sites and critical infrastructure, thereby saving the cost of relocation works. This paper introduces some of these concepts and the process of making the changes leading to potential savings from the improvements, using various examples as proof of the concepts.

Jan 1, 2009

RME has a vision for a new grinding plant operational paradigm made possible by RMEÆs fast, safe Mill Relining System. Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by modifying liner design for maximum life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. Following the introduction, the first section of this paper provides an update describing recent and significant developments within RMEÆs range of Mill Relining Systems, the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The second section outlines RMEÆs vision of a æliner profile versus profitabilityÆ commercial model, developed either intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2007

By R H. Knight

Uncertainty in prediction and modelling of geological (physical) ore continuity in geometrically complex ore deposits is a key risk factor in mining. Reducing geometric uncertainty of hard-boundary ore/waste contacts and related geological features improves the efficiency of local mineral resource estimation and reserve calculation, mine/stope planning, ore control and in-mine exploration. Detailed underground mapping of serial-level drives provides a continuous record of the characteristics and contact configuration of ore, as well as crucial ore-related geological features that are required to resolve geometrical variability when closely spaced drilling proves inadequate or is cost-prohibitive. The mapping-based approach described in this paper re-establishes the focus on the geology of the orebody by incorporating high-value, detailed geologic mine mapping information. Mapped ore-related configurations and relationships, recorded on a succession of faces or on a series of levels, provide the basis for 3D interpolation and extrapolation of the local geologic continuity of an orebody. Correlative points representing locations of key ore-related geologic features on each face or level are linked by 3D polylines or trajectories forming a coherent geometrical framework. The coherent progression of geometric changes mapped by these trajectories reveals the overall ‘dynamic’ of the geometrical framework, as well as the spatial tendencies of its geological constituents. Distinct sets of ore control trajectories are selected from within the framework and are used in the construction of alternative geological ore continuity models. As mining proceeds, alternative models are evaluated, and are then either refined or rejected. The geometrical framework is used to evaluate theoretical models and practical heuristics, focus exploration targeting and inform and guide all aspects of mine geology in active mines. This approach also lends itself to analysis of global ore continuity in the re-evaluation of mature or abandoned mines. Its use is particularly effective in geometrically complex orebodies such as the West Branch orebody and the orebodies of No 2 mine of the Balmat-Edwards-Pierrepont zinc district, which are used to illustrate the method. CITATION:Knight, R H, 2014. A mapping-based approach to geological continuity prediction using examples from the Balmat-Edwards-Pierrepont Zinc District, St Lawrence County, New York, USA, in Proceedings Ninth International Mining Geology Conference 2014 , pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Y Lin, B J. Seligmann, M Hassall, S Micklethwaite

For multi-site mining companies, checking the quality and consistency of the data recorded in risk registers is important for confirming how well mine safety management systems have been implemented. However, this task is complicated by the differences in scope of the site, their particular nature, the complexity of the operations and many other factors that can introduce nuances to the characteristics of the risk registers. We present here an application of a technique called Causal Network Topology Analysis for comparing the quality and consistency of risk registers. By quality we refer to, for example: - missing causal relationships between risks - location of missing controls - focus of risk treatment strategies: prevention versus mitigation controls. By consistency we refer to how causally interdependent are the risk events. There are often causal interactions between the lines of a risk register that mean that the likelihood and consequence scores that are applied to each risk event are not independent. We measure this degree of interactions by: - proportion of independent scenarios per register - efficiency of risk treatment strategy comparison. This approach can indicate quality and consistency differences between registers irrespective of the actual details of the site or operation. This occurs by comparing aspects of the structure of a causal network extracted from how the risk events, causes, controls and consequences causally interact. In this work we compare pairs of registers to demonstrate the approach.

Apr 16, 2024

By J S. Kuszmaul, T O. Aspinall

The applicability of environmental geotechnics for erosion management is increasing in importance worldwide. The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. This is because of the need to increase the reliability of erosion prediction and in the minimisation of costs for spoil dump design. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. Engineering design of mine spoil dumps seeks to reduce the potential for such erosion damage through correct selection of an initial stable landform scheme (Goh, 1997). The design of mine spoil dumps must also conform to the specifications of evolving legislation. The Queensland Environmental Management Overview Strategy (EMOS) states that, for minimised degradation of the surface area due to erosion during the development of a project, the erosion rates should be between 12 - 40 tonnes/hectare/year and that the depths of rills and gullies be limited to less than 30 cm (QDPI, 1988). The aim of engineering design is to ensure the long-term stability of the spoil dumps. The implementation of effective planning and operating procedures through recontouring and grading assists in the reshaping of spoil dumps to a safe, stable and non-erodible environment.

Jan 1, 1998

Madison Enterprises Corp. and Matu Mining are currently ex- ploring the Mt. Kare property in Papua New Guinea. The Mt. Kare gold prospect has had a short but very active history, since the first discovery of gold in the area in 1986 the property has sccn: a 3 year gold rush during which 10,000 alluvial miners re

Jan 1, 1997

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

By Carr SD

The Omineca Belt of the Canadian Cordillera straddles the western boundary of the North American paleocontinental margin and accreted oceanic and island arc terranes. Crustal thickening of the orogenic belt was initiated in the Jurassic and culminated in latest Cretaceous and Paleocene times.Thin-skinned shortening of the Rocky Mountain Foreland Thrust and Fold Belt was balanced by basement-involved crustal imbrication within the Omineca (hinterland) Belt. Middle and upper crustal rocks of the hinterland (Selkirk allochthon) were thrust eastward and ramped onto basement of the North American continental margin. By latest Paleocene the southern Omineca Belt formed an elevated crustal welt that was at least 60 km thick.Within less than 3 Ma of the culmination of crustal thickening the belt was rapidly uplifted and tectonically denuded. The southern Omineca Belt was extended by as much as 80% as upper crustal rocks were displaced on moderate to low angle normal sense shear zones and brittle normal faults. This oro-genic collapse is interpreted to be a gravitational response to crustal thickening and thermal soft-ening, facilitated by reduction in plate-boundary-induced far field stresses.

Jan 1, 1990

By C M. Côte, P Bolz, R Chrystal

The design of final landforms is an integral part of mine closure plans in Queensland and aims to ensure the rehabilitated land is safe, stable and non-polluting. Landform stability in this context is commonly assessed using Landscape Evolutions Models (LEM) which are physical models simulating sediment erosion and deposition around individual landforms over long timespans (up to thousands of years). The most used LEM for assessment of rehabilitated landforms in Queensland is SIBERIA (Willgoose, Bras and Rodriguez-Iturbe, 1991; Tucker and Hancock, 2010). SIBERIA models are complex, require very detailed input data and simulate erosion and deposition over time frames that extend decades beyond closure. They are not suitable to assess erosion risks during the operational phase of a mine and to support the development of erosion and sediment control plans. Other types of erosion models, such as the Revised Universal Soil Loss Equation (RUSLE, Wischmeier and Smith, 1978) or Water Erosion Prediction Project (WEPP, Nearing et al, 1989) calculate soil loss on a monthly or yearly basis and are much better suited to erosion management during the operational phase. They are simpler to implement and can support the design of control measures. For instance, designing a sediment basin requires quantification of sediment loads, which can be produced by these models. In Queensland, the legislation around sediment and erosion control for open cut mines is currently tightening. Soil erosion remains a major concern due to potential impacts on the receiving environment. It requires management during operation and for closure consideration alike and it is critical that erosion and sediment control plans are developed with the most appropriate tools. Globally, RUSLE is the most widely used soil loss model (Borrelli et al, 2021). This is because it is an empirical model with relatively simple input requirements: biophysical data such as soil properties, vegetation cover, topography and rainfall variability, which can be directly measured or derived from regional or national databases and/or spatial data sets that are available in most parts of the world. The second most used model is WEPP (Borrelli et al, 2021) but compared to RUSLE, there is a large drop in the frequency of its use. This is because WEPP is physically-based and has more complex data requirements. WEPP integrates hydrology, hydraulics, erosion mechanics and land cover to predict soil erosion and sediment transport on hill slope profiles and small watersheds (Stolpe, 2005). It requires some biophysical parameters in formats different from those of RUSLE, as well as detailed hydrologic and catchment data. Nevertheless, it has been used in landform design for mines across Australia to determine final landform stability (eg Howard and Roddy, 2012; Costin, 2020). In this study, we assess which tool would be the most appropriate to support development of erosion and sediment control plans from operation to closure. We use RUSLE and WEPP to predict soil loss from a mine site, compare the results from both models and outline the advantages of each method.

Aug 2, 2023

By J Loeb, D Thornton

Blast movement measurement is a key component of grade control, enabling mines to carry all of the precision involved in locating ore blocks, through a chaotic blast, to production. A monitoring system was developed about ten years ago so that mine operation personnel can measure three dimensional movement in every production blast. Research has shown that blast movement is always highly variable with a significant non-deterministic component. The consequence is that modelling will be inaccurate and therefore optimal ore recovery can only be achieved by direct measurement of blast movement.Three dimensional movement vectors are measured at discrete locations in the blast. If blast movement is only measured at one location in a blast pattern, data is severely limited and has all of the inherent inaccuracies of modelling a variable population. It is intuitive that the accuracy of defining the post-blast ore block mark-ups are proportional to the number of movement measurement locations, however increasing the number of monitoring locations causes increases to the direct operating costs of the mine.A cost-benefit analysis is used to explore the optimal number of monitoring locations. Using the method described in this paper, an automated selection of the number and location of blast movement monitors are analysed against the value of recovered ore compared to the control, for each trial.CITATION:Loeb, J and Thornton, D, 2014. A cost benefit analysis to explore the optimal number of blast movement monitoring locations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D Kent, R Paine

"Automated mining systems are increasingly being seen as a key requirement for a productive mining operation in the future. The importance of an integrated communication network infrastructure to support such systems is growing.This paper outlines the introduction of automated mining systems in large conventional mines as well as their growing role in block cave mines currently operating or being developed. The paper will then focus on a case study of how the communication infrastructure is fundamental to the operation of such systems and explain why the resultant communication networks require much more than just increased bandwidth (data capacity) to properly support the automation system within the overall mine operation.Mining operations already embarking down this road are discovering that the required network must be based on a true enterprise level architecture to not only enable the mine’s current plans for remote and automated mining, but also provide a scalable and integrated platform for future developments and requirements. The emerging issues for the communication network to truly support automation systems include: increased complexities of operating and maintaining multiple networks integration issues with disparate systems problems with reporting particularly as demands for corporate reporting and compatibility with enterprise systems become the norm ongoing management challenges, which will only increase with the proliferation of new technologies.The paper will explore how certain mining operations are addressing this by adopting a long-term strategy for automation deployment, which includes laying the necessary foundation architecture to meet their current requirements, while supporting their future visions for the fully automated mine.CITATION:Paine, R and Kent, D, 2014. Developing the foundation communication infrastructure to support remote and automated mining initiatives in underground mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 151–158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By M Robertson

3D photogrammetry is a powerful tool for data capture and interpretation, utilised at all Australian underground MMG sites. In personnel constrained mines, 3D photogrammetry can free up personnel time, improve data quality for resource modelling, as well as benefit other mining departments.At Rosebery one of the challenges faced by geologists was no longer data capture but, rather, avoiding paralysis by analysis from the sheer abundance of information currently available to the department. Although the data had been interpreted, the structural model was cluttered; the geological block model was not incorporating any geological domains captured by 3D photogrammetry, nor was it being utilised by other departments such as geotechnical engineering.The geology department is now focusing on utilising all the interpreted data gained from each photograph heading into an uncluttered, easily understandable model for geologists and other mining departments.Our solutions involve integrating the Leapfrog modelling suite into the process, streamlining the structural model, tailoring the data interpretations for future updates of the block model and training other departments to improve utilisation of the interpreted data. This process also uncovered other benefits for near-mine exploration, and improving our understanding of the deposit’s origin.CITATION:Robertson, M, 2017. The practical use of underground 3D photogrammetry data at MMG Rosebery polymetallic mine, Tasmania, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 409–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By H Park, D J. Holland, L Wang, Y Matviychuk, Y Lee

Reuse of process water in mineral and coal flotation plants is widespread to effectively reduce freshwater consumption. However, the accumulation of the frother in the recycled process water is a growing problem as high remnant frother concentration often leads to undesirable overfrothing issues throughout the plants. Various approaches have been proposed by others to measure frother concentration, but none of them is used in flotation practice owing to the requirement of timeconsuming sample preparation steps and/or specialist training to operate and maintain. There is a pressing need for the development of a simple and fast frother concentration measuring technique to avoid overfrothing issues and to optimise the flotation process. The present paper presents two promising approaches to measuring frother concentration online. The first approach measures the concentration of alcohol type frothers based on the host-guest interactions between frother molecules and a formulated liquid. This method is simple and fast as it only requires mixing the formulated liquid with the water sample for up to one minute. The potential of this approach was demonstrated by determination of the residual MIBC concentrations at different locations across a coal flotation plant. The second approach measures frother concentration using a solid-phase extraction (SPE) process and a cryogen-free benchtop NMR spectrometer. Using this approach, both alcohol type and polyglycol type frother solutions can be analysed for concentration determination within 30 minutes. It has also been demonstrated that the concentration of individual frothers in a frother blend (ie MIBC and PPG425 in water) can be accurately analysed even in the presence of background chemicals. This technique has otential for real-time measurement of frother concentration as the whole process can be fully automated.

Aug 24, 2022

By N McIntyre, R Trancoso, N Bulovic

Mining is essential for facilitating human development particularly as demand for critical minerals grows. However, over the mine life cycle, the environment is permanently changed. Once mining ceases, mine-affected land can leave significant legacy issues on the surrounding environment if not managed. Therefore, mine closure planning is critical. Mine closure occurs over large scales often with the aim of recreating resilient ecosystems over mined landscapes with mitigated negative impacts. The natural state of the landscape and the environmental risks over planning time-scales are largely driven by climate. Climate change is expected to impact different parts of the post-mining landscape, from stable landform design (soil erosion mitigation) to revegetation efforts and pit lake management. Consequently, mine closure plans may need to account for a non-stationary and uncertain future climate, that may be both different to the current climate and evolve during the mine life and post-closure. Here a new data-based approach is presented for incorporating climate change projections in mine closure planning, based on the recently released Coupled Model Intercomparison Project phase 6 (CMIP6) climate data used in the latest Intergovernmental Panel on Climate Change (IPCC) assessment report. The approach: (i) characterises closure-related attributes of the future climate, and (ii) identifies the amount (and direction) of change expected to occur, and its uncertainty, focusing on five metrics for demonstrative purposes and initially describing changes in erosive potential below. This provides information on the type of future environment (ie the changing baseline) that mine closure should plan towards, and identifies rehabilitation options that may be susceptible to increased risks from climate change.

Aug 2, 2023

THERE are few industrial and metallurgieal processes which do not require the application of heat energy, and the modern demand for increased working efficiency has resulted in attention being paid to temperature control as a means of ensuring fuel economy and more efficient plant operation. In general, mill accuracy required is not very contant in laboratory work, and few industrial operations are controlled to within less than 5° while in many cases greater limits are allowable. Almost every thermal property of matter has been suggested as a basis for the construction of pyrometers, but the thermo-electric type finds by far the widest application, and hence this paper will deal only with the principles, construction, and uses of this type of instrument. THERMOELECTRIC PYROMETRY.In the year 1821 Seebeek discovered that if the ends of two dissimilar metal wires were joined and one junction heated, a current flowed in the circuit, and the KMF (electro-motion force) set up could be measured by inserting a galvanometer at the cold junction. The phenomenon was not thoroughly investigated for many years, but, as the demand for high-temperature thermometers increased, several investigators, of whom Le Chatelier was one of the pioneers, successfully endeavoured to utilize the principle in pnometric construction. The couples which gave the most satisfactory results were discovered, improvements were made in material and design and the present-day type of instrument gradually evolved. The apparatus consists of three main parts, viz. (1) The thermo-couple itself of two dissimilar metal or alloy wires together at one end. (2) The leads which connect the terminal of the thermo-couple with the measuring instrument.

Jan 1, 1923

By B Wentzinger

This paper presents the results of state parameter estimates in an active coal boiler ash storage facility using the most recent methods currently in use for cone penetrometer interpretation. State parameters estimates are also compared with the critical yield stress ratio approach, which is proposed as an additional liquefaction potential screening method. Recommendations are provided regarding additional in situ tests and laboratory tests that may be undertaken to improve the state parameter assessment and data produced for use in subsequent stability or liquefaction studies.

Jul 1, 2021