Search Documents

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By Derek J. Penrice

The Caltrain Downtown Extension (DTX) project will extend commuter and future statewide high-speed rail service into the Transbay Transit Center, which will be located in the business district in downtown San Francisco. The DTX project includes 1.5 miles of underground construction, comprising complex sections of mined and cut-and-cover tunnel. As part of the DTX preliminary engineering process, development of appropriate contracting practices, including contract packaging, procurement methods and contract terms for the underground construction, has been initiated. This paper provides a summary of the evaluations undertaken, preliminary conclusions reached, and proposed next steps to promote industry interest and maximize bid competition.

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

By P. A. Hagerty

Biological treatment of metals-impacted water using sulfate reduction is a viable means of treatment that has been applied in pilot and full scale at numerous projects. One of the fundamental challenges with this type of treatment is the selection of an appropriate substrate to support the sulfate reduction process long-term. The substrate degradation products provide a carbon source and an electron donor for metabolism by sulfate-reducing bacteria and consequently organic characteristics are critical; however, the physical attributes of the substrate are equally critical to an efficient and optimized substrate mix. This paper explores the affect of particle size (a.k.a. grain size) of several substrate mixes on the treatment efficiency of sulfate reducing treatment systems. Substrate selection can be separated into two phases of evaluation, the primary selection phase and the secondary optimization phase. The primary selection phase considers such fundamental attributes as source availability, economics, bioavailability and longevity. These fundamental activities are conducted in order to identify potential candidate ingredients of the substrate mix which are regionally available, economically viable and consistent with the biogeochemical aspects of the project. Recent work has been conducted in the development of testing protocol for organic substrates to quantify bioavailability (Martinez Hernandez et al. 2010, Place et al. 2006) as part of the primary selection phase. Once the substrate ingredients have been selected based on the primary criteria, the mixture of these ingredients is then developed based on an optimization process, including consideration of the substrate ingredient?s particle size distribution.

Jan 1, 2011

By David S. Yang, Osamu Taki

The innovative Soil-Cement Mixing Wall Technique, developed independently in Japan, consists of mixing in-place soils with cement grout using multi-axis augers and mixing paddles to construct overlapping soil-cement columns. The applications of overlapped soil-cement columns include cutoff walls for groundwater control and structural diaphragm walls for excavation support. The special features of this technique include water tightness, versatile strength design, and efficient installation in subsurface materials varying from clayey soils to cobbles or soft rocks. Through the introduction of two recent subway projects in Japan, this paper presents the design parameters, construction procedure, quality control and performance of soil-cement wall for excavation support and groundwater control.

Jan 1, 1989

By G. F. Jenkins, P. S. Hobden

Toronto as a geographical area provides an exceptionally wide variety of subsoil stratiphication. Tunneling consequently required a very wide range of adaptabilities to meet its changing conditions. This discussion will provide a summary of work performed in both earth and rock formation using three of our recent works to describe a Contractor's experience. The general subsoil stratigraphy is known to consist of deposits laid down during the Illionian Glaciation followed by the Samgamon Interglacial Stage and finally the Wisconsin Glaciation. All these deposits are underlain by shale bedrock of the Dundas formation. As a whole the Dundas formation is predominantly a greyish blue, thinly bedded shale. The engineering characteristics of the shale vary considerably, however, between a blue clay (argillaceous) shale and a much lighter (in colour) silty and sometimes sandy (arenaceous) shale, and occasional limestone layers. The Illionian deposits are usually found to be layers of pebbly clay till and an overlaying layer of contorted varved-clay. These glacial deposits can be overlain by a thick layer of sandy silt to silty sand which is identified as the Samgamon Interglacial sediments. Because of the action of erosion the Wisconsin till sheets, many times separated by interstadial sands, can vary greatly in their number of layers from zero to three or more.

Jan 1, 1997

This study was conducted to establish the effects of a diesel particulate filter (DPF) system with sintered metal substrate on the concentrations and size distributions of nano and ultrafine aerosols and concentrations of nitric oxides in underground mine air. The study focused on the formation and transformation of nucleation mode particles in mine air under prevailing test conditions. Experimental work was conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of control technologies directly in underground conditions. The DPF system was examined for four repeatable steady-state engine modes using a naturally aspirated mechanically controlled Isuzu C240 diesel engine fueled with ultralow sulfur fuel. The engine coupled to an eddy-current dynamometer was operated in the underground drift with tightly controlled ventilation. Measurements upwind and downwind of the exhaust system discharge were used to quantify the effects of the DPF system on the mine air. A baseline was established using a standard muffler. The study showed that sintered metal DPF systems reduced the total mass of aerosols in the mine air by more than ten-fold when compared to a muffler. The nucleation mode aerosols (50dem<40 nm) in mine air were found to be strongly influenced by engine operating mode. The concentration of nucleation mode aerosols was found to be significantly higher for high-load modes than for low-load modes. The muffler and DPF system resulted in comparable total nitrogen oxides (NOx) concentrations. However, the nitrogen dioxide (NO2) fraction of the total NOx was found to be substantially higher for both systems for low-load modes than for high-load modes.

Jan 1, 2009

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

By Leeming. J. R.

In the UK, powered supports are normally salvaged from longwall faces on completion of production, for reuse on the next unit. Where a spare set of supports are held, the salvaged supports are often stored in underground roadways awaiting installation. One mine in the UK extracts a 5m section, and holds two sets of 2x950t powered supports, each weighing approx. 35t and having closed dimensions of 8m long, 2.5 high and 1.75m wide. As the first set would not be required for over 12 months, and because of space limitations below ground, it was decided that the supports would be left in situ, the district sealed, and reopened at a later date for support salvage. The paper described the decision making process, and the inertisation of the sealed district utilising nitrogen generated on the mine surface and piped to the point of use. The re-entry and re-ventilation of the district are also described. The paper then goes on to describe in more detail the discovery of a spontaneous combustion event that occurred in the waste behind the powered supports, and its treatment and control using extra nitrogen brought to the mine by tanker and introduced at strategic locations along the faceline via boreholes, leading to a successful salvage and re-sealing.

Jan 1, 2009

By T. C. Pool

Physical and chemical conditions permitting, in-situ leaching (ISL) of uranium offers a variety of advantages over conventional production methods including less surface disturbance and less solid waste. Commercial production of uranium by in-situ leaching techniques was initiated in 1963 in the Shirley Basin of Wyoming by Utah Construction. On a world-wide basis, ISL uranium production amounted to about 13.2 million pounds U3O8 in1999, approximately 16% of world output. Both acid and alkaline systems are used, the selection of which is primarily dependent upon groundwater quality and related reclamation requirements. ISL offers low capital costs per unit of annual capacity and is particularly flexible in adapting to changing market conditions.

Jan 1, 2000

By W. K. Callaway

The need to increase ore recovery and pillar stability caused the Magmont Mine staff to investigate the use of sandfill to accomplish both tasks. The use of hydraulically stowed classified mill tailings as a subsidence preventative will be discussed as well as the use of sandfill in pillar recovery and as a part of the regular mining cycle.

Jan 1, 1986

By Paul Richardson

This paper will review several projects completed during the period from 1976 through 1984 which have been carried out utilizing big hole drilling concepts. The projects discussed will be from various industries to demonstrate the extent that big hole drilling methods are being used along with the current state of development. There will be a discussion of projects planned for the future where big hole drilling methods are the only technology being considered. Also included in the discussions will be an overview of the most recently completed heavy oil recovery project. During the next decade, big hole drilling methods will be used more and more in all industries where underground access is required. The safety, speed and economics associated with shaft sinking using drilling methods are becoming more and more recognized and the technology is rapidly becoming an accepted shaft sinking method.

Jan 1, 1985

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By A. J. Kwitowski

Remote control is usually associated with deep mine, continuous mining machines. This is because thin-seam operation precludes an onboard operator&apos;s compartment or the mine has approval to conduct extended cut mining. Using a tethered or radio-linked control box, the remote operator is typically situated 3 to 15 m (10 to 50 ft) from the working face. The operator receives direct operational cues through senses like vision, hearing and feel. Remote control is sometimes touted as a safety feature. However, this is not always true, as operators are not provided protection from roof and rib falls or being crushed between the machine and a rib. Remote control operators are also left exposed to dust and noise. Teleoperation described here is the computer-based, distant control of mining machinery from a protected operator compartment located out of the line-of-sight from the operational site. Video, sound and other sensory information are gathered through sensors and electronically transmitted to and displayed at the operator&apos;s location. The teleoperator responds to the information and makes decisions that are initiated by control devices (usually switches). These control commands are then electronically transmitted to the re¬mote machinery and the appropriate machine function(s) are carried out. Teleoperation increases the safety of mining machine operators as it removes them from the immediate vicinity of hazards. The US Bureau of Mines&apos; involvement with teleoperation dates back to 1979. Following feasibility studies, a highwall milling system (HMS) was developed and tested. A deep, thin-seam, room-and-pillar system (TSRPS) has been designed and is currently being surface tested.

Jan 1, 1992

By Wern-ping (Nick) Chen

The Florida Department of Transportation District 6 (FDOT D6) began a study in 1987 for a master plan to improve the traffic circulation and congestions between the Port of Miami (POM) and downtown Miami, FL. This study included a tunnel connection between two man-made islands, the Watson and the Dodge islands. Though a finding of no significant impact (FONSI) was completed in 1992, the project remained on hold for about 10 years. In 2002, Florida Turnpike took over this project, re-evaluated its benefits to the lo-cal communities, determined its feasibility (specifically the tunnel options) and established a probable cost. In 2005, the FDOT D6 regained its charge over the project and concluded that a bored tunnel under Biscayne Bay is feasible. Its primary components are: ? Widening of the MacArthur Causeway Bridge, to accommodate truck traffic to the Port of Miami. ? A tunnel connection between Watson Island and Dodge Island, where the POM is located. ? Connections to the POM roadway system, either for the traffic from the city of Miami or for the truck traffic from I-395 to the POM. The project will improve access to and from the POM and provide a dedicated roadway connector linking the POM with the MacArthur Causeway (State Route 41/1) and I-395, specifically for the trucks in and out of the POM without going through downtown Miami. As identified in the project information memorandum (PIM), its primary objectives are to: ? Improve access to the POM, helping to keep it competitive and ensuring its ability to handle projected growth in its cruise and cargo operations. [ ] ? Improve traffic safety in downtown Miami by removing POM traffic, trucks and buses from the congested downtown street network and, in doing so, facilitate ongoing and future development plans in and around downtown Miami.

Jan 1, 2009