Search Documents

By HONGWEI YANG, Lili Zhang

Copper slag is mainly used in cutting tools, abrasives, asphalt pavement, road construction, and in the production of concrete as an alternative to sand and cement [1]. As a renewable resource, only about 15-20 percent of the slag is used for these applications, and the dumping or disposal of surplus unused slag results in waste of a certain amount of usable metal in the feedstock [2]. In this work, the oxidation behavior of copper smelting slag under nonisothermal condition is studied using data obtained by the thermogravimetric (TG) method, and the kinetics parameters and reaction mechanism of oxidation are determined. It provides a theoretical basis for the comprehensive recovery of iron resources in slag and the selection of reasonable slag-making conditions.

Oct 1, 2022

By T. P. Meloy

Improvement of grade and recovery requires the use of optimum processing circuits. Critical to an optimum circuit is the set point for separation. With the introduction of the concept of circuit analysis (Meloy, 1982), it became possible to determine optimum circuits for a given task. No analysis, however, has yet been made as to the grade requirements of the larger circuits. Williams and Meloy (1982), reviewed the literature and concluded that, within the operating range, most unit operations involved in particle separation behave linearly. For the purposes of this analysis, linearity will be assumed. Grade, G, is defined as the weight of the coal mineral, C, that appears in the product, divided by the weight of the coal mineral plus the weight of the gangue mineral or waste mineral, Q, which appear in the product.

Jan 1, 1982

By A. L. Hannaford

Previous production at Spektakel was undertaken during the periods 1854 - 1888 and 1892 - 1901. During this period a total of 41,7 kt of ore grading 32% Cu was hand-sorted from 270 kt to 360 kt of ore mined. Initial open-pit mining was followed by underground mining, access being by means of an inclined shaft to the 85 fathom level. During the period 1946 - 1952 cement copper equivalent to 5,452 kt of blister was produced by leaching of oxidized ore. The Spektakel ore-body branches and coalesces both in plan and in cross-section which accounts for its remarkably complex configuration. Constituent rock-types are andesenite and various varieties of biotite diorite and of ?norite? (biotite-hypersthene diorite). Closely related spatially, and possibly genetically, but predating the above-mentioned basic rocks are bodies of biotite-bearing monzoritic rocks, locally termed shonkinita.

Jan 1, 1981

By Frederick S. Fisher

Three spatially separate porphyry copper/molybdenum deposits are associated with the Tertiary Needle Creek igneous center in the southern Absaroka Mountains, Wyoming. In all three deposits a central zone containing disseminated copper and molybdenum is surrounded by a halo of small, discontinuous base and precious metal veins. Propylitically and phyllically altered rocks are common in all three mineralized areas, and potassically altered rocks are locally present. Fission- track age data from apatite and zircon indicate that mineralization occurred about 32-40 m.y. ago. Limited data suggest that the lead isotopes are nonradiogenic, similar to porphyry copper deposits elsewhere in the western United States. The complex igneous history of the Needle Creek center has involved several periods of intrusive and probably extrusive activity. lntrusive rocks are calc-alkalic and include andesite, granodiorite, diorite, quartz monzonite, dacite, and rhyodacite. Stocks (1-30 kmz in exposed area), radial dike swarms, and sills make up the presently exposed plutonic masses and constitute lower-level vent fillings in an old stratovolcano. The Needle Creek igneous center is located approximately midway along a northwest-trending belt of intrusive rocks extending more than 100 km along the central axis of the Absaroka volcanic field. The igneous and mineralized centers within this belt were probably localized at the intersections of northwest- trending Laramide and possibly Tertiary fracture systems and earlier northeast-trending Precambrian structures in the underlying basement rocks.

Jan 1, 2013

By S. Serata

Background Results of the above study in the August 1991 issue of Mining Engineering offer valuable lessons in the solution of cutter-roof problems. The original study plan was initiated by the discussion authors to solve the problems using the "stress control method" of mining (Serata 1976,1982; Serata, Carr and Martin, 1984; Serata and Gardner, 1986; Serata, Gardner and Preston, 1986; Serata, Gardner and Shrinivasan,1986; Serata and Kikuchi, 1986; Serata, Preston and Galagoda, 1987) However, the plan and the planner were changed to the arrangement reported in the paper. The change was considered reasonable at the time due to the mine engineers' uncertainties about the stress control method. Consequently, the basic principle of the study was shifted from the original stress control method to the method described in the paper, which will be called the "yield pillar method" for the purposes of this discussion. The paper convinces the reader that the yield pillar method fails to solve the cutter-roof problems. This doesn't mean that the stress control method also fails. Actually the contrary is true, as discussed below. Limitation of the yield pillar method The paper illustrates clearly how poorly the yield pillar method performs in solving the problem. The reason for this failure is the lack of the protective stress envelope needed to stabilize the cutter roof. Unfortunately, the protective envelope cannot be formed properly without utilizing the stress control method of mining. Changing the pillar size does not make much difference in the roof stability.

Jan 1, 1992

By L. S. Gourevitch, E. B. Kremer, A. Y. Fidlin, Y. M. Katsman, I. I. Blekhman

A new kinetic approach to simulation of fracture is given. The main object of the simulation is forecasting transformation of ore lumps size distribution in squeezing of ore layer between two planes. The approach rests on fundamental principles of energy and mass conservation and on new ideas about fracture physics connected with fractal geometry. On this base an integro-differen tial equation of layer crushing kinetics is formulated. This equation is similar to well-known kinetic equation of grinding, but here we use elastic energy density in place of time as an independent variable while selection function is considered by us to be dependent on this variable. Properties of the equation have been investigated by us and its analytical solution has been found. It allows to compute simultaneously both the evolution of the size distribution process of squeezing and force-displacement diagram. Results of theoretical calculations provide a good fit with experimental data.

Jan 1, 1995

By S. Hartwig, K. Wohiwend, J. Forsberg, G. Bergling

New, larger cutters requiring higher operating loads and thus increased cutterhead thrust, higher cut¬terhead speeds and more pronounced demands of maintaining high penetration rates also in mixed ground, constantly augment the loads on TBM main bearings. At the same time, the demand of a single TBM model covering a wide diameter range limits the available space for the main bearing at the smaller end. Innovative concepts and advanced methods of calculating bearing loads and lifetimes are needed to meet the demands which TBM suppliers and their customers face. This paper reviews different design approaches and covers the influence of lubrication on bearing life and condition monitoring as well.

Jan 1, 1995

By J. A. King, D. R. Weir, P. C. Robinson

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration. Minipiloting of the preconcentration and oxidation stages of the Porgera flowsheet are described. The influence of these processes on subsequent recovery of precious metals together with the technical and economic necessity of concentrate pretreatment prior to oxidation are discussed.

Jan 1, 1987

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat, A. J. S. (Sam) Spearing

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. Initially, ASTM A615 grade 60 steel roof bolts, which are the most commonly used bolt material in the United States, were tested with and without stresses in a simulated underground coal-mining environment for approximately six months. This paper mainly discusses the test system, protocol and system shortcomings, and makes recommendations based on the observations and results.

By A. Dell’Era, E. Ciro, C. Lupi

The paper explores the recovery of indium via electrowinning from sulfate baths, focusing on the impact of different cathodic supports (AISI 316L and nickel) on process parameters such as electrolyte composition, current density, and temperature. The study compares productivity, morphology, and structure of indium deposits on both cathodes, finding that nickel cathodes generally yield better results.

Nov 1, 2023

By Henry H. Roos

NTRODUCTION In the mining industry, a "drill jumbo" is a drilling unit equipped with one or more rock drills and mounted on a mechanical conveyance. Jumbos range from single¬drill ring drills mounted on simple steel skids to sophisti¬cated multiple-drill units mounted on diesel engine powered carriers and equipped with automatic controls and sound-abatement cabs. Individual types of jumbos usually are designed for specific tasks such as fan drilling in sublevel caving operations. Some units, such as development jumbos, can be utilized for several functions in addition to their normal applications, e.g., for production drilling in room-and-pillar operations, stoping in cut-and-fill mining, etc. Mine operators can purchase individual components from manufacturers, assembling these components into a jumbo suitable for specific conditions. However, this requires that mine personnel have good engineering and mechanical abilities. Although manufacturers of jumbos maintain facilities for designing machines to meet con¬ditions created by new mining methods and unusual ap¬plications, the cost of the engineering and experimental work for new types of jumbos should be evaluated in terms of both costs and benefits; it may be advantageous to plan the mining operation so that existing and proven units can be utilized. GENERAL SELECTION CRITERIA Since the operating conditions vary in underground mines, the design of a jumbo must be selected to cope with the individual characteristics of the mine. The necessary considerations include access space into the working areas, grades expected to be encountered, radii of the curves, ambient temperatures, the characteristics of the rock, the acidity or alkalinity (pH rating) of the mine water, etc. Access to Mine Workings The mine workings must be accessible to the selected jumbo. Frequently, a jumbo must be disassembled at least partially to pass through the mine shafts. There¬fore, a bolted construction allowing disassembly into pieces of suitable size and weight is desirable in most applications. Type of Undercarriage Generally, a crawler-type undercarriage should not be used in trackless mines having acidic mine water. The acidic water causes an electrolytic action between the individual crawler parts and causes rapid corrosion and early failures. Propulsion A two-wheel drive on a pneumatic-tired jumbo is marginal for grades exceeding 12%. A four-wheel drive unit with good weight distribution is capable of operat¬ing on grades of up to 35%. At least 30% of the gross vehicle weight (GVW) should be carried on the steering axle; otherwise, the steering tires may not have sufficient traction on loose road surfaces and may "plow" instead of steer. To assure stable operation in mines with steep grades, the height of the center of gravity of the jumbo should be considered. It should not make the unit prone to rolling over on the steep grades that may be encoun¬tered. Turning Ability In confined working areas, a skid-steering or crawler unit has the best maneuverability. An articulated carrier is preferable when base-rotated parallel booms are being utilized. A rigid-frame jumbo with automotive steering is compact and economical, having lower maintenance requirements than the other two types. However, the turning radius of a rigid-frame unit is wider than either the skid-steering or articulated units, and this wider turning radius may be detrimental in mines with narrow drifts. JUMBO COMPONENTS Rail Undercarriages A mine with a rail-transportation system generally utilizes drill jumbos that are mounted on rail-type under¬carriages. With a light load and good weight distribu¬tion, this carrier may consist of a simple two-axle four-wheel platform onto which the boom-mounting brackets are attached. As the depth of the round and the penetration rates increase, the weight of the equip¬ment installed on the chassis also increases. The greatest problem with a heavy overhung load is balancing the carrier; a three-boom unit may require a substantial amount of counterweighting to maintain an acceptable 70% to 30% axle-load balance. Although lengthening the wheelbase helps balance the unit, a long wheelbase increases the turning radius, often creating problems on curves and sometimes requiring a swivel truck-type chassis. A good rule of thumb for a simple four-wheel undercarriage is to maintain a wheelbase length to track gage-width ratio that does not exceed 2.5 to 1.0. For a larger ratio, a swivel truck should be utilized. Swing-out outriggers or roof jacks help keep a jumbo in place during the drilling cycle. Usually, a rail-mounted jumbo is not self-propelled. Instead, it is maneuvered into place by a locomotive. Occasionally, several headings are being advanced in close proximity, and a self-propelled jumbo is con¬venient. In electrified mines, such a jumbo utilizes conventional battery-powered traction gear; in dieselized mines, hydrostatic drive components offer good flexi¬bility. The tractive power requirements of a typical rail jumbo may be calculated from the formula: HP = [(RR + GR) X Sl/[33,000 X Em X Eh]

Jan 1, 1982

By RICKARD HANSEN

Vehicle fires in underground mines pose a certain risk for which measures to prevent or mitigate the fires are highly important. Fire protection measures can be divided into active and passive measures, where active measures require an external power to work in the event of a fire, and passive measures could include an existing partition preventing fire spread. As passive fire protection does not rely on activation, it is expected to provide high reliability and a robust solution, and should be considered during the design process. This paper investigates passive fire protection measures that could be implemented in the design of mining vehicles. It was found that passive fire protection should include the use of several measures simultaneously to ensure fire protection throughout the different phases of a fire. Threshold distances for fuel components were calculated, and it was found that combining hydraulic hoses and electrical cables resulted in larger threshold distances. A pool fire along the underside of a vehicle will pose a certain risk, and passive measures should be focused on ignition prevention, making high demands on the insulation/shielding along the underside. Any occurring tire fire may pose a challenge, and the priority should be on preventing ignition. Potential measures include shielding the wheelhouse and applying fire-resistant sealings.

By W. Ripmeester

Canada is committed to the development of indicators to measure the contribution of its minerals and metals sector to sustainable development. The Minerals and Metals Indicators (MMI) Initiative is described, including drivers for the development of indicators, the MMI theoretical framework, the multi-stakeholder consultation process utilized in the development of indicators, and possible policy and business implications of MMI.

Jan 1, 2003

By J. Loeb, R. Ramanathan, P. Cameron

All mining operations, including iron ore, maintain a focus of continuous improvement and asset optimisation in their operations. As all the operations in the Mine-to-Mill value chain are inter-dependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and the impact of changes to the process. In this paper, we discuss some of the key attributes in the mine to mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve mine to mill processes. Mining operations are planned and executed based on designs and models to achieve the operation’s objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Measurement of the key attributes establishes the baseline for Mine to Mill (or Pit to Plant) performance which is necessary to understand the impact of any proposed improvements to the process design and execution and to monitor the outcomes on an ongoing basis to sustain the improvements that have been implemented. We have focused this paper on two types of measurement – blast movement and particle size of materials through the mine to mill process. Several innovative technologies are already available to measure these attributes and assist operations improve productivity and mine site profits.

Mar 2, 2022

By L. R. Hossner

Chemical and physical properties of surface soils and overburden materials must be evaluated prior to strip mining activities. This information can be used to assess whether subsurface overburden can be equal in quality to the existing surface soils, especially when these soils are classed as prime farm lands. In Texas, materials from the Carrizo, Calvert Bluff, Simsboro, and Hooper Formations overlie the lignite. The Carrizo Formation consists of thick clean sands with poor water and nutrient retention capabilities. These materials are least suited for placement of the surface of reclaimed land. The oxidized, medium textured overburden from the Calvert Bluff and Simsboro Formations possess adequate water and nutrient properties and are better suited for sustained plant growth. Non-oxidized Calvert Bluff and Hooper sediments generally have acceptable properties for reclamation. However, caution must be exercised in vegetating these materials since they may contain acid forming sulfide minerals.

Jan 1, 1982

By R. T. Leigh

The continued decline In the production of synthetic soda ash (sodium carbonate) due to high costs and associated environmental factors, has improved the world demand for natural soda ash. The largest resource of natural soda ash is the mineable trona deposits of Southwestern Wyoming. Wyoming trona, a lacustrine evaporite of Eocene Age, is mined by five producers which process over 90% of the United States and 20% of the worlds soda ash. Total world consumption of soda ash is forecast to grow 1% annually. Increased expansion into foreign market's is absorbing the domestic overcapacity.

Jan 1, 1989

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem.

Jan 1, 1989

By Robert A. Haney, Scott G. Vail, Kenneth G. Fields

The Mine Safety and Health Administration, in cooperation with IMC Global Operations, Inc., conducted a joint study to determine the effectiveness of the technology currently in use at the mine to control diesel particulate exposures. IMC Global operates an underground potash mine using diesel-powered equipment to extract minerals. IMC uses a variety of technologies to control worker exposures to diesel particulate. These technologies include: ventilation, low sulfur fuel, oxidation catalytic converters (OCC), maintenance and work practices. The study was conducted over a two-week period, two shifts per day. During the first week (six shifts), baseline data on exposures and diesel particulate emissions were obtained. New OCC's were installed over the weekend on all equipment on the test section. During the second week (six shifts), data were collected to assess the effectiveness of the new OCC devices. In addition to exposure and diesel particulate emissions data, mine ventilation, engine exhaust temperatures and mine operational data were obtained. The primary means of determining diesel particulate concentrations was the respirable combustible dust (RCD) method. Gas concentrations carbon monoxide (CO), carbon dioxide (CO,), and nitrogen dioxide (NO,) were measured using passive dosimeter badges and gas bottles. Results of measurements of diesel particulate, gases, and air- flows were analyzed to determine the effectiveness of airflow and oxidation catalytic converters for controlling diesel particulate exposures. The use of oxidation catalytic converters resulted in reductions of both workers' exposures and diesel emissions.

Jan 1, 1997

By W. Zitz

Incorporation of heat exchangers into drilled shaft foundations is a novel approach to both improve the energy efficiency of building heat pump systems and provide necessary structural support using the same construction materials. In an effort to quantify the structural and heat exchange performance of deep foundations used as ground-source heat pumps, two instrumented test foundations were constructed as part of a new construction project in Denver, CO. They will be integrated into the conventional ground-source heat pump system for the building. This paper focuses on the lessons learned from the construction process for these energy foundations.

Jan 1, 2011

By Clifford J. Lewis

The role of calcareous minerals in that area of the environmental improvement program involving the control or elimination of sulfur oxide emissions is discussed, and a new concept in gas scrubbing, rendering possible the use of calcareous rocks more extensively for this purpose, is presented. Calcareous rocks are defined as the more common limestones, consisting essentially of calcium carbonate and magnesium carbonate. The effect of magnesium carbonate on the reaction rate of limestones and lime toward sulfur oxides in aqueous scrubbing systems is pointed out. The relative economics of lime- stone versus lime as aqueous scrubbing reagents for sulfur dioxide are indicated.

Jan 1, 1974