Search Documents

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By R. D. Coursen

Tin has been one of the very few commodities which has been covered by an international commodity agreement. It is the only metal so covered. The reason behind tin's prediliction for an agreement has been the inconsistency of the price pattern for tin during the entire 20th century. It is not surprising in view - of the wide and wild fluctuations in its price that tin has been called the Cinderella metal. An examination, for example, of prices in 1977 alone attests to the erratic behavior of the tin markets. The high was recorded on October 27 at M$1,895 per picul and the low on January 3 at M$l,314 3/8, on the Penang market, a spread in Malaysian dollars of $581 for a picul weighing 133 1/3 pounds. The first steps in international cooperation on tin were taken after the price bonanza of the First World War. Despite a lack of increased consumption, and in spite of the fact there was no shortage of mining production during the war, prices boomed. Shipping shortages and thinning stocks brought about a situation where in the U.S., industrial stocks were only 1/6 of what they had been in 1914. The boom busted early. In 1921 the tinplate industry of the world had cut its output in half and total world consumption of tin fell by 1/3. Tin producers became so concerned that they created what was called the Bandoeng Pool. It accumulated stocks held by countries now known as Indonesia and Malaysia, amounting to 28 percent of the combined production of the two countries and about 15 percent of the total world for 1921. The pool holdings were shortly exhausted and thereafter in the years 1924 to 1928, general boom conditions existed for tin.

Jan 1, 1978

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011

By John M. Heckard

It all started with the National Environmental Policy Act of 1969, which establishes that Congress is committed to restore and maintain environ- mental quality. It directs all federal agencies to identify and develop methods and procedures so that environmental parameters and values will be given equal consideration in the decision-making process, along with economic and technical parameters. Section 102 of the Act directs, among other things, that all agencies will submit a detailed statement on: (1) the environmental impact of the proposed action, (2) any adverse environmental effects which cannot be avoided should the proposal be implemented, (3) alternatives to the proposed action, (4) the relationship between local short term uses of man's environment and the maintenance and enhancement of long term productivity, (5) any irreversible and irretrievable committments of resources which would be involved in the proposed action should it be implemented. Passage of this act has been followed by other legislation, both federal and state. The Water Quality Act of 1970 puts teeth into the previously existing Federal Water Pollution Control Act by requiring a "certificate of reasonable assurance that the activity licensed will not violate the applicable water quality standards." The Clean Air Act of 1970 requires that the Environ- mental Protection Agency establish national air quality standards, as well as standards for significant new pollution sources.

Jan 1, 1973

By Gilbert Sauriol

The mining complex, which the Mines Gaspé division of Noranda Mines Limited has operated in Murdochville since 1954, includes open pit and underground mines, two mills, one leaching plant and a smelter. The under- ground mining uses predominantly a large scale room and pillar method, rooms 15 m wide, 30 m high and 300 m long being common. Ore production is effected by 4.5 m3 front-end loaders and 32-tonne trucks powered respectively by 225 and 325 kW diesels. Daily dust and gas readings show that air quality can be maintained at an acceptable level with much less ventilation than that normally specified. This paper emphasizes the point that air requirements should be based on Air Quality Standards, thus allowing an operation to benefit from favourable conditions or from improvements such as exhaust treatment, fuel alteration, etc.

Jan 1, 1983

By William H. McLemore

Geologists searching for carbonate rocks suitable for chemical uses traditionally have relied on extensive laboratory testing in order to locate strata or zones that might be suitable for mining. However, when considering the significant time and costs involved in sampling and performing chemical analyses, any exploration technique whereby fewer samples and analyses are needed would be of great value. In other words, if the exploration geologist could "zero-in" on select areas, considerable time and money could be saved. In general, the major-element chemistry of carbonate rocks is determined by the abundance of the minerals present. CaO occurs with CO2 as the mineral calcite, which is the primary mineral comprising allochems, matrix and sparry cement; MgO is found in high-magnesium calcite (many calcite fossil species contain appreciable amounts of MgO in solid solution), dolomite, and chlorite; iron occurs in pyrite and in limonitic stylolites, as well as in chloritic and glauconitic clay minerals; materials containing abundant Si02 are microcrystalline quartz (chest) silt-sized quartz, and clay minerals; and Al203 is found primarily in illitic, kaolinitic, and chloritic clay minerals. The presence or absence of these minerals determines the chemical composition of the carbonate rooks.

Jan 1, 1983

By Stephen Utter

This report summarizes the results of preliminary investigations concerning the influence of block caving mining upon adjacent mine openings and discusses possible methods for reducing critical rock pressures and damage to these openings. These investigations are one part of a general study of the rock mechanics of block caving by the Denver Mining Research Center of the Federal Bureau of Mines. The purpose of this part of the study Is to obtain an estimate of the stress concentrations around mine openings adjacent to block caving stopes for use in developing better designed openings and improving mining methods. When mine openings such as slusher drifts, grizzly drifts, and haulage drifts are damaged by rock pressures induced by block caving mining, the mining cost increases, mine production decreases, and ore recovery may be consider- ably lessened. Methods of mining that result in lower rock pressures and methods of design that enable mine openings to withstand these pressures are desirable. The development of these methods, in turn, requires a fuller understanding of the following: The stres concentrations around the mine openings and the changes in stress induced by adjacent mining; the physical properties, such as the compressive strength and modulus of elasticity of the rock surrounding the openings; and the support supplied by the concrete lining, timber sets, or other types of supports used in the openings.

Jan 1, 1962

By VASU GANGRADE, Marcia Harris, Kumar Vaibhav Raj, Jim Addis, Khaled Mohamed, Snigdha Sarkar

The National Institute for Occupational Safety and Health (NIOSH) conducted a ventilation assessment for a recently established underground room-and-pillar stone mine implementing split-mine ventilation. The primary objective was to examine the impact of the length of the in-place stone stoppings on face ventilation efficiency. These stone stoppings serve to separate the intake and exhaust entries and align with the mining direction. To achieve this, computational fluid dynamics (CFD) modeling was utilized. The appropriate turbulence model was selected, and a mesh convergence analysis was conducted for the CFD model. Following that, the CFD model was validated using the conducted ventilation surveys. Two configurations of in-place stone stoppings, designated as Layout-I and Layout-II, were simulated using the validated CFD models. Layout-I featured a shorter in-place stone stopping, while Layout-II had a longer one. The results obtained from the CFD models demonstrated that the increased length of the in-place stone stopping in Layout-II resulted in a notable enhancement in ventilation efficiency at the advanced faces (last stopping), elevating it from 4% in Layout-I to 8.4% in Layout-II. However, no significant impact of the in-place stopping layouts was observed at other faces. In general, Layout-II exhibited a greater circulation of air at the outby stoppings.

Feb 1, 2024

By John L. Ellenberger

Virtually no two mines operate with the same geographic, geologic, and mining conditions. It follows chat problems vary with the conditions from mine to mine or often from one section to another in the same mine. Actual situations are described, and a technique of "stacking" maps to predict hazards is presented. Two case histories of the use of multiple overlays are de- scribed. The first deals with a property that was examined before the start of mining. The second is a property in which severe ground control problems were encountered and the relationship between the problem areas and known conditions were found to be related.

Jan 1, 1981

By Colin D. Jardine

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. A recent application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by the use of a "building block" approach to design and equipment selection. Details of this approach and the results obtained are described.

Jan 1, 1982

By Francois E. Heuze

We demonstrate a new capability to analyze the behavior of circular shafts in jointed rock. This was made possible by the development of a new, axisymmetric, joint finite element (2). Whereas the only previously reported such element was singular (1) and inadequate at some orientations, the current element has been extensively validated (3). The need for including discontinuities in a shaft analysis comes from two sources. First, the various rock formations may have discrete jointing, bed- ding, and interface between them. Second, there is a joint at the boundary between a concrete liner and the rock, and possibly between the various segments of the concrete liner. To demonstrate the applicability of the new model, we analyze a vertical circular shaft 5.4 m in diameter, in a series of horizontally bedded sandstones and siltstones. The shaft excavation is followed through three initial steps: 6 m, 15 m and 24 m deep.

Jan 1, 1979

By F. B. Olender

Idler engineering, operation, and maintenance cannot be covered in depth in a short paper. Therefore, this will be a general look into the subject matter in light or the present-day technology. Depending on the source or reference used, belts for handling bulk material underground came into being between 1900 and 1920, while strip mining appeared in the thirties. The conveyor belt speeds in that era were in the 300 rpm to 500 rpm range. Belt speeds or 600-700 rpm were in vogue in the thirties, and the early sixties saw speeds or 800-900 rpm. Today, speeds or 1000 rpm are not looked at with dismay; in fact, speeds or 2000 rpm are being discussed. Among the driving forces moving the bulk materials handling industry to these greater heights have been the mining operators and engineers. Their appetite to increase output, yield, and reduced per-ton costs has constantly challenged the bulk material handling industry to develop products capable or handling these increased capacities. One or the products affected by this movement is the idler. Apart from the conveyor belt itself, it is one or the most significant parts or a conveyor system because or the sheer numbers needed in an installation.

Jan 1, 1971

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

A worker’s personal exposure to respirable dust in occupational environments has traditionally been monitored using established methodologies which entail the collection of an 8-hour representative sample that is sent away for laboratory analysis. While these methods are very accurate, they only provide information on the average exposure during a specific time period, generally a worker’s shift. The availability of relatively inexpensive aerosol sensors can allow researchers and practitioners to generate real-time data with unprecedented spatial and temporal granularity. Low-cost dust monitors (LCDM) were developed and marketed for air pollution monitoring and are mostly being used to help communities understand their local and even hyper-local air quality. Most of these integrated sensing packages cost less than $300 per unit, in contrast to wearable or area dust monitors specifically built for mining applications which have been around for decades but still average around $5,000 each. At the National Institute for Occupational Safety and Health (NIOSH), we are leveraging the power of high-volume data collection from networks of LCDM to establish baseline respirable hazard levels and to monitor for changes on a seasonal basis as well as following any application of control technologies. We have seen the effective use and advantages of monitoring live data before, during, and after events like shift changes, operational changes, ventilation upgrades, adverse weather events, and machine maintenance. However, many factors have prevented a systematic adoption of LCDMs for exposure monitoring: concern for their analytical performance, the complexity of use, and lack of understanding of their value are some factors. This contribution outlines a one-year case study at a mine in Wisconsin USA, covering the installation, maintenance, data visualizations, and collaboration between NIOSH researchers and the industrial hygiene professionals at the mine.

Feb 1, 2024

By C. J. Weiss

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an underground coal mine in eastern Kentucky. This field study was conducted as part of a larger multi-site evaluation of available TTE systems to determine their operational sensitivity. Field testing is being performed along with simulation techniques developed for geophysical surveys. The results of the field test will additionally be used to determine the applicability of these simulation techniques to TTE communications. The mine detailed in this paper was idled at the time of the study, which provided the nearest practical representation of a post-event mine shutdown. For this study, the three following communication modes were tested: surface-to-underground, underground-to-surface and surface-to-surface. Standard deployments of the TTE system using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations. Other arrangements of the units yielded intriguing results, some of which were predicted by computer simulations, others were unexpected. Future experimentation is planned to further evaluate the observed phenomena. INTRODUCTION The ability to establish effective communication between surface and underground personnel after a mine event is essential for both mine evacuation and mine rescue efforts. Current communication technology is reliant on physical infrastructure, such as antennas, cables, and repeaters, located throughout the mine. Such systems are easily disabled during a mine event because of their vulnerability to physical damage. A true emergency communications system would have the ability to function regardless of a mine’s physical state. Through-the-Earth (TTE) wireless communications technology has the potential to provide such a tool. Wireless TTE communications are exceptionally challenging because electromagnetic (EM), or radio, signals are subject to drastic attenuation as they travel through solid strata. In addition to attenuation, EM wave propagation is directly affected by the physical and petrographic characteristics, mineral compositions, metamorphic properties, and the degree of water infiltrations in the strata [1-5]. These strata characteristics are unique to each mine thus making the design of an effective, universally deployable, and reliable TTE communications system very difficult. At present, TTE technology is in the preliminary stages of practical deployment with only a few permissible TTE systems commercially available."

Jan 1, 2015

By Earl G. Hoover

For most geologists and miners the term "asbestos" refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for? uses where incombustible, nonconductive or chemically resistant material is required. The United States Mining Enforcement and Safety Administration (MESA) specifically refers to the naturally occurring minerals chrysotile. amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as "asbestos" if the individual crystal fragments have the following dimensions; length -greater than 5 micrometers, maximum diameter -less than 5 micrometers, and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer causing agent) it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment.

Jan 1, 1978

By J. A. Pigott

Undercut-and-fill mining is a method developed by the International Nickel Company to deal with abnormal pillar mining conditions at one of its mines. Results have been such that its use has been extended to normal, pillar recovery operations in other mines of the Company as a replacement for conventional square-set pillar mining. It is anticipated that the method will also largely replace square-set stoping at INCo mines, especially for mining at deep horizons.

Jan 1, 1962

By Chi-shing Wang

In many cases the roof strata of a bedded deposit may be considered as a composite of rock beams of rectangular cross section, whose component layers differ in thickness and may or may not be separable from each other when they are subjected to loading by their own weight. An analytical study of the behavior of such multiple-layer beams is extremely difficult owing to the heterogeneity and anisotropy of rock materials. The complexity is revealed by the fringe photographs obtained from several series of barodynamic photostress experiments conducted on various types of multiple-layer model beams of a medium-grained Bedford limestone. Further discussion on the applicability of barodynamic photostress techniques to the model study of the behavior of mine roofs in stratified geologic media is presented by comparing the phenomenological observations recorded in this investigation.

Jan 1, 1968

By J. Richard Tonry

In portland cement manufacturing, the raw materials axe changed to clinker in the burning operation. Generally the rotary kiln is used for this purpose and involves many processes, including pelletizing and nodelizing. This transformation is called clinkering, and is analyzed as now generally practiced in cement making, from the raw material to the resulting clinker.

Jan 1, 1963

By Kenneth W. Torpey, James G. Ball, Richard F. Flanagan, David S. McAllister

INTRODUCTION Under a Federal grant by the Urban Mass Transit Administration (UMTA) (80%), and sponsored by the State of New York (200), Niagara Frontier Transportation Authority is constructing a 10.3 km (6.4 mile) light rail rapid transit system in Buffalo, New York. The $450 million project, which began construction in the Spring of 1979, is unique in rail transit alignment designs in the U.S.A. and the first predominantly underground light rail system in North America. The Buffalo project is unique in that the first phase of the expandable system follows the alignment of Main Street and is on the surface in a proposed 1.6 km (1.0 mile) pedestrian mall in the downtown business district. The alignment then progresses northward into a cut-and-cover portal and standard double-box configuration for 2.74 km (1.7 miles) at a depth of 9.1-10.7 m (30-35 ft) and subsequently drops into bedrock at depths of 18.3-27.4 m (60 to 90 ft). The 5.63 km (3.5 mile) rock tunnel section consists of two single tunnels 4.88 m (16.0 ft) nominal finished diam. and includes five stations. The rock tunnel line section was divided into a north and south contract of 2 316 m (7,600 ft) and 3 243 m (10,640 ft), respectively. Due to the existing surface facilities and the future station locations, the line tunnel contracts differed considerably in their shaft access

Jan 1, 1981

By George E. Aiken

Agglomeration developments in the iron ore industry of North America are closely related to shifting patterns in commercially acceptable ore grades and even the definition of iron ores. These relationships have occurred mainly during the last 20 years. Many of these changes are an outgrowth of events which involved the history of the Mesabi Range. Although magnetic taconites had been discovered in the Lake Superior area about 1870, they remained unvrorked in part for lack of concentration methods and a generally unfavorable economic climate. Some 20 years later the rich Mesabi hematites were found beginning the era of direct shipping ores which continued through World War II. These Lake Superior iron ores included reserves of an estimated three billion tons. Following World War II, decreasing ore grades and rising costs began to force the closing of many underground iron mines. The early 50's saw the beginning of the decline in direct shipping ores and a spurt in produc- tion of natural iron concentrates. However, the market for unprocessed concentrates began to decline in the early 60's as agglomerated products and foreign ore s began to dominate the U. S. market.

Jan 1, 1973