Search Documents

By J. J. Pavlica

Grinding in steel mills adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and short-circuit current measurements were made on electrode combinations of pyrrhotite-mild steel and pyrrhotite-stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of ' an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles caused slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1982

By Ralph M. Stricklen

The need to move large tonnages of slurry has grown as mines have become larger. As existing tailing depositories are filled up, new mines developed, or environmental requirements dictate, it becomes necessary to transport tailing particularly over longer distances. A typical slurry transport system is shown in Figure 1A. Figures 1B, 1C and 1D show sketches of the system auxilliary components: feed box, receiving sump and drop box, respectively. There are two basic types of slurry transport systems, packed flow and slack flow. Packed flow is typified by a pipe running full; slack flow by a launder or pipe running less than full. Slack flow in launders or channels is also referred to as open channel flow. Generally slack flow slurry transportation involves a flow with less than 65 per cent solids, and there is an upper limit on particle size, depending on the slope of the system.

Jan 1, 1984

The choice between EPB - and Slurry Shields is influenced by the following factors: grain size distribution, cohesiveness, occurence of boulders, occurence of gas, feasibility of soil separation and muck disposal, and settlement properties of the soil. The simple equation cohesive soils = EPB Shields and non cohesive soils = Slurry Shield is very often superimposed by other facts. For example, the occurence of a large amount of boulders in weak cohesive soils, where the application of roller discs is not recommendable, may lead to the use of a Slurry Shield with a rock crusher, thus accepting the disadvantage of a sophisticated separation plant; whereas the occurence of contaminated groundwater or gas may exclude the use of a Slurry Shield. In the following examples the choice of a Slurry Shield or EPBS will be explained and justified with regard of the above factors.

Jan 1, 1995

By Robert M. Stevens

INTRODUCTION Truck haulage of muck in underground mining operations has been in use around the world for many years. From the late 1.950s into the early 1970s, haulage by means of load-haul-dump (LHD) units challenged haulage by means of trucks, and, to a large degree, LHD units dominated the trackless concept of moving mate¬rial underground. However, beginning in 1975, the emphasis began to shift back to the use of trucks, with LHD units assuming the secondary role of loading the trucks. Over the years, several manufacturers have been offering trucks with capacities ranging from 4.5 to 45.4 t (5 to 50 st) and with features that specifically address the constraints of underground operation. TRUCK TYPES Three different types of trucks are available for use underground, namely the tip dumpers, telescoping dumpers, and push-plate dumpers. The following para¬graphs describe each of these three types. Tip Dumpers Tip dumpers are designed to lift the truck box, using gravity to dump the load out the rear of the box. The primary application of these trucks is in the haulage of muck to the surface. However, these trucks also may be utilized underground, if a chamber is provided to accommodate the raised truck box at the dumping point. Fig. 1 illustrates a four-wheel drive truck with a 10.0-t (11-st) capacity; this truck is only 1.9 m (6.25 ft) wide and is designed specifically to follow narrow and winding vein courses. Fig. 2 illustrates a two-wheel drive tip dumper with a 24.5-t (27-st) capacity; this truck operates on 12% grades with firm dry surfaces and in modes both loaded-up and loaded¬down. Telescoping Dumpers Telescoping dumpers specifically address the constraints imposed by low back heights, and they represent an optimization of compressed envelope size with maximum payload capacity. Figs. 3 and 4 illus¬trate a typical telescoping dumper with a capacity of 18.1 t (20 st). Fig. 3 shows the box in position for carrying the load, and Fig. 4 shows the same truck with the box in the full-dumping position. Fig. 5 illustrates the loading and dumping cycles. Fig. 6 illustrates an approximation of how an LHD unit with an eject-o-dump (EOD) bucket would be used to load over the rear of this type of truck. Fig. 6 shows a low-profile telescoping truck in the first stage of loading, with a 6.8-t (7.5-st) LHD unit equipped with an EOD bucket. A loader with a smaller capacity and a narrower bucket would allow the bucket to fit inside the truck box and would achieve an even lower loading height than that illustrated. Gen erally, an LHD unit equipped with an EOD bucket and teamed with a telescoping dump truck can be used with a lower back height than could any other front-end loader and truck team. Push-Plate Dumpers Push-plate dumpers are similar to telescoping Bump¬ers, except that they do not have the two-stage box. Instead, push-plate dumpers utilize a single push plate to discharge the load out the rear of the box. Gen erally, these units are limited to payload capacities of about 9 t (10 st). Fig. 7 illustrates a typical push-plate dumper.

Jan 1, 1982

By Betty L. Gibbs

Before the first shovelful of dirt is removed from a developing mining property, a wide range of data must be collected, organized and analyzed. Among the key steps in this process are: • Visualization of the deposit from drill hole data and geologic interpretation, using all available information, including surface geology, geochemistry and geophysics. • Drawing of vertical and horizontal sections. • Construction of a 3D solid model of the deposit. • Contouring of deposit outlines and geological structure until the model represents best estimate of reality. • Estimation of grade and quality distribution. • Calculation of reserves. • Examination of possible mining methods. • Determination of economic feasibility. Many techniques are available to aid in this process of mine project feasibility analysis, from quick pencil calculations to sophisticated computer methods. However, time races faster in the complex modem business world than it did 50 years ago. Tried and true pencil methods take too much time. Opportunity may pass a mine developer by while a property is still in the first stages of analysis. In the days of hand techniques, initial analysis of the economic feasibility of a mining project usually stopped with reserve calculations and broad mine planning. Further planning was not done or was done only for the short term. Manual techniques require too much time and manpower to evaluate a longterm mining program. Mining-industry recognition of computer utility has increased. Most companies now use computers in technical applications and could not conceive of working without them. Building initial computer models of a deposit may take nearly as long as hand techniques. But the payback comes when changes are needed and a variety of mine plans are quickly tested.

Jan 1, 1990

By Fathi Habashi

THE UNIT process of adsorption involves two steps: 1) Loading of the adsorbent. 2) Recovery of metal values from the adsorbent. Charcoal is the adsorbent commonly used in extractive metallurgy. The discovery of the adsorptive power of charcoal from solutions is generally accredited to Lowitz (1785), who observed that several dissolved organic substances were precipitated on charcoal. Graham was the first to demonstrate that inorganic substances were also adsorbed on charcoal. In 1830, he reported that iodine dissolved in KI solution was adsorbed on charcoal. Also calcium ions were adsorbed from limewater, as were lead ions from lead nitrate solution. The use of charcoal in metallurgy was first applied

Jan 1, 1970

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By Dr. Richard F. Coon, James D. Mavis

Risks and abatements associated with preliminary reconnaissance, plugging and filling, and maintenance of perched mine water pool are examined. This case history showed that the initial appeal of portal plugging was replaced by concern over potential environmental hazards when details of implementation were investigated.

Jan 1, 1992

By C. McDonald, S. Slottee

Deep "paste" thickeners have been used in the alumina industry for several decades to improve chemical recovery and allow “stacking” of the red mud for disposal. These paste systems have eliminated many traditional tailings ponds in addition to providing better tails washing and better water recovery. This technology is not widely used or understood in other mineral processing applications. However, there is growing worldwide recognition of the advantages of concentrating mill tailings to a “paste”, i.e. a solid suspension that does not settle or segregate. This technology offers several alternatives to the traditional tailings pond such as “stacking” or mine backfill. More water recovery is possible than with high rate thickeners. Process benefits come in the form of better chemical and metals recovery through better washing in counter current decantation (CCD) applications. Obtaining a true paste (non-segregating suspension which exhibits a yield stress) and understanding the handling characteristics for applications outside alumina, are recent developments. Achieving all of the benefits available from a paste system requires careful design that takes into account the specific requirements of the disposal application along with the peculiar difficulties in producing and handling paste. In fact, design of a paste system is markedly different from a conventional system. Project design usually requires the cooperation of experts in several interrelated specialties including geotechnical, thickener design, pumping and discharge design and controls. A successful project must coordinate all activities to ensure that the overall objectives for the project are achieved. This paper describes the properties of paste, reviews the applications, and discusses the design of a complete paste deposition system.

Jan 1, 2003

The concept of classification in wet, closed circuit ball milling is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters that effect fines removal are identified and discussed, and a quantitative index for circuit classification effectiveness is presented.

Jan 1, 1987

By Atmesh K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high Btu low sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high Btu midwestern coal and blending it with low sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal is presented.

Jan 1, 1984

By Andrew J. Neale, Chelvan Veloo

P.T. Freeport Indonesia currently operate a 600,000 t/d mining and 125,000 t/d milling operation in the remote highlands of Irian Jaya, Indonesia. The isolated location and generally difficult working conditions make for challenges not encountered in most North American operations. In spite of this, the mill technical groups have been able to develop and maintain a highly effective level of plant wide automation. This has been achieved through the appropriate selection of available technologies and the implementation of innovative management practices. This paper provides an overview of the control systems currently installed and focuses on those practices which have resulted in the long term success of process control at Freeport.

Jan 1, 1997

By Slobodan Vujic, Goran Cirovic, Dragan Radojevic

Mine production systems (MPS) are characterized, more or less, by the following properties: uncertainty, subjectivity, impreciseness, polysemy, instability, indefiniteness and lack of data. From modern study aspect these MPS mathematically belong to the class of fuzzy systems. With this in mind, the usage of fuzzy sets is recommended as a methodology that treats impreciseness, indefiniteness and complexity of mine production systems in a satisfactory manner. Fuzzy modelling, discussed in this pa- per, is applied as a mathematical implement. The objective of the paper was to show production optimization in practice on the ex- ample of bauxite open pits where fuzzy linear programming (FLP) was used following the criterion per income. The variables in criterion function are linguistic variables while both variables and variable restrictions are presented by triangular fuzzy numbers (TFN). The term "satisfactory income" presented through triangle fuzzy numbers was introduced instead of "maximizing the income". sensitivity of the obtained solutions has been analysed

Jan 1, 1996

By Brett Schug, Caelen Anderson, Sohail Nazari, Carlos Cristoffanini

"The Haile gold mine in South Carolina is increasing the automation level of its processing plant in order to improve operational stability. One step toward this goal is the application of a digital twin concept to provide virtual instruments. Haile has engaged Andritz to implement virtual instruments at its grinding area hydrocyclones and at its tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The digital twin is a first-principles integrated design engineering with advanced simulation (IDEAS) simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters.OceanaGold’s Haile gold mine is located near Kershaw, SC, about 80 km (50 miles) southeast of Charlotte, NC. This location was first mined in 1827 and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile operation.The current operation began in 2017 as an openpit mine with additional underground resources. The nameplate throughput is 5,760 t/d (6,350 stpd) ore, and 2017 production was 3,345 kg (118,000 oz) gold, with 3,968 to 4,384 kg (140,000 to 155,000 oz) gold expected in 2018. Proven and probable reserves exceed 85 t (3 million oz) gold at a grade of 2 g/t (0.06 oz/st) gold. The process, as shown in Fig. 1, includes a primary jaw crusher, comminution with a semiautogonous grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon-inleach leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile operation’s inaugural gold pour took place Jan. 20, 2017. Mine life is expected through the year 2030."

Dec 1, 2018

The 1996 Arizona Conference was held in Tucson on Dec. 8 and 9. Attendance was 648, a 12% increase from the 1995 conference. The annual conference is organized by the Arizona Conference Board of Directors, representing SME sections from throughout Arizona and adjacent areas. In addition to those representing mining and processing operations in the Arizona region, the meeting was well attended by interested parties from throughout North America. These included vendors, consultants, academia, research organizations and corporate management. The technical program highlighted the meeting. It consisted of a keynote address and morning and afternoon technical sessions. In the technical sessions, 23 papers were presented by the mining, hydrometallurgical, smelting, geology and mineral-processing divisions. The conference was then capped by a banquet that included a talk by a noted economist. Keynote address The program was kicked off by a keynote address titled "Forecasting for the 105th Congress," by Rep. John Shadegg (R-AZ). He was elected to Arizona's Fourth Congressional District in 1994. Shadegg serves on the House Budget Committee, the Resources Committee and the watchdog Government Reform Committee. He stressed the familiar conservative positions of reducing government spending, balancing the budget and states rights. As a member of the House Resources Committee, Shadegg stated his support for the mining industry. Technical sessions Mining division. Two of the five presentations described developments at two Arizona mining operations. T.J. Swendseid of Phelps Dodge presented a paper titled "New developments at Morenci" and P. Garretson of BHP presented a paper titled "Startup of the Robinson Project." Morenci continues to expand its operation and recently broke records for production. Other developments at Morenci included the completion of a 600-m (2,000-ft) drainage tunnel and stockpile rehandling. In addition, Phelps Dodge moved Morenci's crusher plant. It was completely disassembled and reassembled in just eight days. Another interesting presentation was "Predictive maintenance techniques for large electric shovels at Cyprus Sierrita," presented by T. Ritzel of Cyprus Amax. The presentation described high-technology methods for predicting maintenance problems. These methods included vibration analysis, ultrasonic detection, infrared thermography, electrical measurements and tribology (the science of lubricant evaluation). The benefits of these techniques are reduced downtime of the equipment, as was demonstrated in case studies at the mine. The other presentations were "Introduction to NOSA 5-star safety program," by R. McKinnon, BHP Copper North America, and "A new design guideline for mine sealing," by K. Fuenkajorn, Rock Engineering International. Hydrometallurgical division. The hydrometallurgical session consisted of five papers. These included a presentation titled "Recovery of gold and silver using guanidine-based extractants," by M. Vining of Henkel Corp., Tucson, AZ. In this presentation, guanidine-based extractants LIX-79 and AURIX resin were introduced. LIX-79 was shown to have applications in copper-gold and high silver ores. In ammonia-cyanide leaching, AURIX was shown to be more selective in CIL vs. RIL comparisons. Other papers in the hydrometallurgical division included "Application of cobalt in the copper industry," by J. Hawke, OMG Apex Inc.; "Series parallel conversions and production gains at Cyprus Miami Mining's dump leach and solvent extraction operation," by E. Bilson of Cyprus Amax; "Lead alloy anode corrosion at the San Manuel SXEW tankhouse," by W .M. Gort of BHP Copper and "Hydrometallurgical treatment of copper refinery slimes," by B.C. Wesstrom of Phelps Dodge. Smelting division. Three papers were presented in the smelting division session. These included updates and reports on improvements at the Hayden, Hidalgo and BHP San Manuel smelters. For example, W.A. Dutton of Phelps Dodge presented "Recent improvements at the Hidalgo Smelter." These changes were aimed at reducing environmental emissions and increasing production. They included modifications to the fugitive-gas collection system to reduce particulate emissions, rubber lining the acid plant scrubbers to reduce corrosion and the installation of a cold lime softening system for water treatment. Equally interesting papers were presented by D. Norton of Asarco, Hayden, AZ, in a paper titled "Update of the Hayden smelter process," and by D. Jones of BHP Copper, San Manuel, AZ, in a paper titled "Update on first campaign of the BHP San Manuel Copper." Geology division. The session began with a paper that outlined the progress of an exploration project in South America. "The Pierina exploration project, Ancash Province, Peru" was presented by J.D. Lowell, Lowell Mineral Exploration, Rio Rico, AZ. Another paper was then presented on a copper deposit in Grant County, New Mexico. "Zonation of supergene copper minerals at Hanover Mountain, Grant

Jan 1, 1997

By J. P. Ferro, W. H. Stewart

Wet ground and dry muscovite mica continued to be the most commercially significant types of mica in the US. Canada's phlogopite mica and some US deposits of sericite mica have also contributed to the overall application of mica in a variety of industries. Mica's major end uses are paint, rubber, and construction material. Its value was about $30 million last year. The southern Appalachian Mountains weathered granitic bodies and pegmatites continued to be the primary US muscovite mica source. North Carolina production of mica as a coproduct of feldspar, kaolin, and lithium processing accounted for more than 60% of the total output. New Mexico, South Carolina, South Dakota, Georgia, and Connecticut accounted for the rest. Flake mica was also produced from mica schists in North Carolina and South Dakota. It is also being investigated in Ontario, Canada. Wet ground mica Wet ground mica was produced by four companies: KMG Minerals, Franklin Mineral Products, J.M. Huber Corp., and Concord Mica. KMG and Franklin Mineral Products accounted for more than 80% of the production. Wet ground mica is a highly delaminated platey powder used to reinforce solvent and aqueous system paints for increased weatherability, durability, and greater resistance to moisture and corrosive atmospheres. In plastics, it is an excellent filler and reinforcing agent, providing better dielectric properties, heat resistance, and added tensile and flexural strength. In the rubber industry, wet ground mica is used as a mold lubricant to manufacture molded rubber products, such as tires. It also acts as an inert filler that reduces gas permeability. Miscellaneous uses include additives to caulking compounds, foundry applications, lubricants, greases, silicone release agents, and dry powder fire extinguishers. Wet ground mica prices range from $353 to $496/t ($320 to $450 per st) fob plant. Specialty products may be higher, depending on customer requirements. Dry ground muscovite mica Dry ground mica was produced by nine companies: KMG Minerals, Unimin, US Gypsum, Mineral Industrial Commodities of America, Spartan Minerals Corp., Asheville Mica Corp., Deneen Mica Co., Pacer Corp., and J.M. Huber Corp. Dry ground mica's primary market is wallboard joint compound. Here, it is a functional extender that improves the physical properties and finishing characteristics of the mud. It is also used in various grades as a filler in asphalt products, enamels, mastics, cements, plastics, adhesives, texture paints, and plaster. Dry ground mica became popular as an additive in oil well drilling fluids, where the mica flakes platey nature helps seal the well bore, preventing circulating fluid loss. But oil's dramatic price drop and consequent curtailing of well drilling brought this once booming market to a virtual halt. Forecasters predict that this business will gradually pick up during the next few years and most current dry ground mica producers will again produce the oil well drilling material. Dry ground mica prices range from $110 to $420/t ($100 to $380 per st) fob plant. High quality sericite mica, sometimes referred to as an altered muscovite, was mainly produced by two US companies. Mineral Industrial Commodities of America and Mineral Mining Corp. have equivalent capacities of about 27 kt/a (30,000 stpy). The majority of the material produced was consumed by the joint compound industry. Minor uses are in paint and oil well drilling. The lack of ground sericite penetration into the traditional ground muscovite markets is attributed to high silica content, typically in excess of 20%, and a bulk density. Prices range from $88 to $187/t ($80 to $170 per st) fob plant. Phlogopite mica is a dark colored, magnesium bearing mica rarely found in the US. Suzorite Mica Corp., a division of Lacana Petroleum, mines a deposit in Quebec that is 80% to 90% phlogopite. The dark color has prevented the material's entry into the traditional paint markets. But the physical properties and high purity make it useful as a low-cost reinforcing filler in many plastics and several asphalt applications. Phlogopite mica is ground to several grades and may be treated with various surface coatings for use in plastics or coated with nickel for EMI/RFI shielding applications. Prices for phlogopite products range from $144 to $580/t ($104 to $580 per st) fob plant. As in recent years, production of domestic muscovite sheet - block, film, and splittings - remained insignificant. These resources are limited and uneconomic due to the high cost of hand labor required to process sheet mica in the US. Imports from India and Brazil were the primary sources of the estimated 1 kt (2.4 million lbs) valued at $2.5 million consumed by US electronic and electrical equipment manufacturers in 1986. Reserves As a feldspar, kaolin, and lithium industry coproduct, flake mica will continue to provide a large percentage of mica re- This summary of 1986 mica activity was received too late to be used in the June issue.

Jan 7, 1987

A Mark IV surface force apparatus (SFA) was used to conduct direct force measurements between mica surfaces in dodecylamine hydrogen chloride collector solutions at varying pH levels. It was found that long-range hydrophobic forces reach a maximum at pH 9.5, which also corresponds to the maxima attained by the contact angle and flotation recovery of quartz. The charge densities are comparable on both mica and quartz surfaces (0.40 to 0.48 nm2), making it possible to draw conclusions on the flotation of quartz from the direct force measurements conducted on mica. Therefore, it may be suggested that, in the pH range of 8.0 to 10.3, the maximum flotation recovery of quartz may be attributed to the appearance of a long-range hydrophobic force, which, in turn, can be related to the formation of a close-packed monolayer (or hemimicelle) in the presence of neutral amines formed as a result of hydrolysis.

Jan 1, 1998

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999