Search Documents

By Thomas A. Simpson

Heretofore, underground coal mines in Alabama have operated under only 60 to 360 meters of cover: however, new mines (at least 5 in the early opening or development stages) will be operating under cover ranging from 600 to 660 meters. With increased rock confining pressures, roof stability problems will become more critical. Initial studies in two 7 ½ -minute quadrangle areas in the Warrior coal basin of Alabama indicate that the orientation of certain lineament and fracture-trace modes mapped from ERTS-1 (Earth Resources Technology Satellite) imagery correlate closely with the strike of joint and fault modes. High altitude (118,000 m) U-2 aircraft data were used to support these findings. In addition, over 50 percent of the normal faults mapped in the study area could be directly correlated with ERTS and U-2 lineaments and fracture traces. These correlations provide clues to the structural development of the Warrior coal basin and may, in turn, be used as a guide to the prediction of roof-stability conditions in advance of mining.

Jan 1, 1975

By E. J. Ostrowski

The history of ironmaking dates back to 4000 BC when an open forge was used to produce a sponge iron from a heap of ore and charcoal. Even at this early date, man recognized the need for a fuel and a reducing agent. As time passed, man developed new methods of producing iron; however, these developments were centered on the mechanical aspects, and as a result, a furnace evolved which is now known as a blast furnace. During this period of evolution,' man struggled with the only fuel he knew - charcoal. Some 5600 years passed before any attempt was made to use coal as a fuel for the blast furnace. The use of coal had its beginning in 1619 when Dud Dudley of England first attempted its use in the blast furnace; as a-fuel and as a reducing agent. Coal charged to the top of the blast furnace was not satisfactory. The volatile matter of the coal choked the flues, and also the poor, strength qualities would not support the weight of the ore. Breaking up of the coal compacted the stock column to an impervious mass. One hundred and sixteen. years later in 1735, Abraham Darby of England introduced coke as the fuel and reducing agent in the blast furnace. The acceptance of coke as a fuel for the blast furnace was not spontaneous. As late as 1870, one-half of the pig iron product of the United States was made with anthracite coal, 30 per cent with raw bituminous coal and coke, and 20 per cent with charcoal. However, by 1910, 96.2 per cent of the blast furnace product was made with coke, 2.4 per cent with anthracite and coke admixture, and 1.4 per cent with charcoal. Coke became the standard fuel in the blast furnace. As the art of ironmaking progressed, more pig iron was produced and more coke was consumed. Coke oven capacity was progressively increased. In 1910, there existed approximately 4,000 coke ovens; in 1960 there was approximately 15,000 ovens. This increase in coke oven capacity was necessary to feed the mammoth appetite of modern blast furnaces.

Jan 1, 1962

By B. Das

Most coals are susceptible to spontaneous heating which in turn creates problem to mining, storage and transportation of coal. It is impossible in actual practice o eliminate spontaneous heating but spontaneous combustion can effecively be controlled through a clear understanding of its mechanism and the factors affecting it. There are altogether six stages in the process of spontaneous combustion. This includes the water adsorption stage and six oxidation stages: chemi-sorption (upto 70°C), decomposition of peroxygens (70°C-150°C), oxy-coal formation (150°C-230°C), combustion initiation (230°C) and active combustion (> 230°C). Heat is produced in all these stages. On the other hand heat is also dissipated so that some equilibrium temperature is reached. If this temperature exceeds a certain critical value (generally about 70°C), coal oxidation may advance to spontaneous combustion. The major factors influencing spontaneous combustion of coal are: coal rank, maceral composition,, water, mineral matter, joints and fissures, seam depth and thickness, mine Layout, method of ventilation, etc. Susceptibility is high for low rank coals and generally decreases with increase in rank. Of the macerals, the exinites are generally most susceptible, the inertinites least and the vitrinites somewhere in between. Water plays a major role on the spontaneous heating of coal, assisting in someways and inhibiting in other. Unrecovered coal in the gob (generally in thick seams) is a major source of fire hazards and this is specially important in shallow mine. Proper design of mine ventilation system can substantially reduce the risk of mine fire. Panel layout and load transfer can affect the development of induced cracks which in turn influence spontaneous heating. Finally, the difference between the spontaneous heating of coal in a seam and that in storage or transportation is mainly due to the change in moistured content, air circulation through the coal and coal fragmentation. These aspects have been analyzed in this paper with a view o reducing the risk of spontaneous combustion.

Jan 1, 1986

By J. R. Mackie

Reserve Mining Company, the first large-scale taconite pellet producer in the United States, mines it's crude ore at the Peter Mitchell Mire located on the eastern end of the Mesabi Iron Range near Babbitt, MN. The ore is processed at Reserve's beneficiation plant on the north shore of lake Superior at Silver Bay, M. The mine and plant are linked by a 47 mile, double track, railroad which is owned and operated by Reserve. (see Fig 1). At rated capacity, the mine can produce 33 million It/yr of crude ore, 15 million It/yr of waste rock and 1.0 - 1.4 million yd3/yr of glacial till stripping. Haulage of all mined material is accomplished using trucks. Ore is transported by tractor-trailer side dump units which have capacitys ranging from 83 to 110 long tons. Waste rock and glacial till is transported in end dump units of 50 to 120 LT capacity. Loading is accomplished by 11/13 yd3 power shovels and 7/10 yd3 front-end loaders.

Jan 1, 1985

By G. Davis

Mineral properties and mineral firms often trade at a market value that is significantly greater than the value indicated by discounted cash flow (DCF) techniques. A possible explanation is that DCF analysis does not consider the value derived from managerial flexibility. Presumably, then, at least some of the difference between DCF value and market value is due to managerial flexibility. This paper surveys the recent attempts to empirically quantify the value of managerial flexibility using option pricing theory. The results indicate that managerial flexibility, at least as measured by the option pricing methodology, falls well short of explaining the gap between DCF value and market value.

Jan 1, 1995

By R. Bruce Tippin

because of the mineral's high monetary value and the spotty occurrence of free gold in the deposit. Setting up a plant sampling procedure by simply applying the usual statistical sampling theory was questionable. Two sampling concepts were considered in the sampling study: o a sufficient number of assays can be taken such that the average determined from these individual samples represents a known quantity of ore. o a sufficient weight of sample can be taken such that when assayed it represents a known quantity of ore. The test program included evaluation of sampling techniques, sample preparation and analytical methods. The overall sampling program is depicted in Figure 2.

Jan 1, 1985

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By Gordon B. French

In order to better understand the relation- ship of underground and surface oil shale processing systems, a block flow chart is presented in Fig. I. From this figure only modified in-situ and Room and Pillar underground mining are currently committed and into the Detailed Design and Construction phases. Figure II illustrates the times required (Federal land site) to bring oil shale operation into production. As this example shows, only those companies having progressed beyond the exploration stage have a chance to obtain oil shale production within the next 10 years. A more detailed breakdown of the oil shale development for those on private lands or having already obtained Federal lease lands is shown in Fig. III for shale oil development (without major regulatory changes).

Jan 1, 1981

By H. B. Charmbury

In Pennsylvania there are two distinct coal regions, bituminous and anthracite, in which the mining conditions and production trends are different. Bituminous mining is more mechanized, and production is increasing. This report is concerned specifically with the bituminous area. The bituminous coal industry apparently is facing a shortage of miners and mine officials which may become acute by 1970. Since 1949, when Pennsylvania had more than 100,000 bituminous coal miners, the number has steadily decreased. There are two principal reasons for the decrease of certified miners and mine officials. These reasons are the fact that apprentices are almost a thing of the past and the fact that the image of the coal miner is a poor one to people in general and to parents in particular. This has contributed greatly to the high average age of our miners today. The average age of all those employed in the mines is 50. Yet it is known that the progress in mine mechanization requires younger and more alert men to operate the newer type equipment.

Jan 1, 1966

By P. J. Ryan

Phelps Dodge’s Candelaria copper-gold mine is located 20 km (12miles) south of Copiapó in northern Chile’s Atacama province (Region III) (Fig. 1). The Candelaria Mine is about 800 km (500miles) north of Santiago and 75 km (47 miles) east of the Pacific Ocean. Its elevation is 600 m (1,970 ft) above sea level. The Copiapó River Valley is 6 km (4 miles) northeast of the mine site. It is the only major source of water in this arid region. The average rainfall is 14mm/a (0.5 in./year). During 1995, the mine produced 521.4 kt (574,800 st) of copper concentrate containing 150 kt (165,000 st) of salable copper and 3 t (98,800 oz) of gold. The 1995 unit cash cost was less than 50 cents/lb of copper. This makes Candelaria one the world’s lowest cost copper producers.

Jan 1, 1996

By Brett P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using alkali solutions1. Without implementing emission controls, world energy emissions will rise from 29.7 billion t in 2007 to 42.4 billion t in 2035. The first objective of the project was to determine the optimal amount of alkali in solution for CO2 absorption. This was accomplished using theoretical equilibrium calculations and experimental absorption data for alkali solutions of 1, 2, 3, 4 and 5 weight %. As the % alkali in solution increased, so, too, did the ionic strength of the solution. Theoretical calculations took into account the effect increasing ionic strength will have on the solubility of gaseous CO2. The calculations assumed negligible formation of H2CO3, constant temperature and constant pressure. In the experimental setup, a 16% CO2 /balance air gas mixture was bubbled through an Erlenmeyer flask filled with an alkali solution. The gas exiting the flask was fed to a gas analyzer to record the % CO2 in the exhaust gas stream. The % CO2 absorbed was taken as the % CO2 in the exhaust gas minus the % CO2 in the feed. Theoretical calculations found that as the % alkali in solution increases, the solubility of CO2 decreases. This was verified by experimental data, which found that a 2% alkali solution, by weight, was the ideal solution for CO2 absorption. Current research is focused on using the 2% alkali solution for permanent storage of CO2 via mineral carbonation to produce a value-added product.

May 1, 2012

By R. R. Johnson

The Hama Mining Company owns and operates The Groveland Mine near Iron Mountain, in the Upper Peninsula of Michigan. The orebody is part of the Menominee Range of the Lake Superior District. The ore (generally known as Jasper taconite) contains an average of 35% iron ranging from 28% to 39% with an overall split of 60% magnetite and 40% hematite. The variations encountered throughout the orebody require a certain amount of blending to reduce feed changes to the mill. One of the variables which affects the crushers, as well as the mill, is the range of hardness which has a low of 7.9 and a high of 24.6 as measured by the Bond Twin pendulum impact and crushing technique. Reference is made to hardness only to point out its effect on crushing and wear rate variations. Over a period of time, these variables do, of course, average out. Mining of the low grade ore started in 1959 and has operated continuously to date. Preparation of the feed for conventional rod and ball mill grinding is accomplished by three stages of crushing. Reduction of crude ore is first passed through a 54 inch gyratory crusher; then through a secondary crusher; followed by two or three tertiary crushers in closed circuit with screens as production quotas require (Figure 1). Current demand to the crushers is about 5,200,000 tons of crude ore per year.

Jan 1, 1976

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

By R. Schipper

Two bench scale biochemical reactors (BCRs) were operated over a period of 3 months for the removal of uranium, radium, and selenium from mining influenced water (MIW). A BCR is an anaerobic reactor comprised of organic and inorganic substrate including woodchips, straw, sawdust, and limestone. Uranium and selenium are removed in a BCR by biological reduction of oxidized species (i.e., selenite, selenate) to less soluble forms (Pahler et al. 2007, Blumenstein et al. 2008, Rutkowski et al. 2013). It is believed that radium may be removed through absorption to the biomass in the BCR. The bench scale BCRs were constructed of 6 inch PVC columns with a top to bottom flow configuration. The bench influent water consisted of three different water ratios from two adit seeps. BCR hydraulic retention times of 24 to 36 hours were targeted during the study. Influent concentrations ranged from 19 ug/L to 1.86 mg/L for dissolved uranium, 12 ug/L to 270 ug/L for dissolved selenium, and 4.9 pCi/L to 24 pCi/L for radium 226. The average and maximum dissolved uranium removal was 93.6% and 98.5% respectively, the average and maximum dissolved selenium removal was 93.3% and 98.9% respectively, and the average and maximum radium 226 removal was 89.5% and 100% respectively.

Feb 23, 2014

By John F. Shea

When Dick Robbins asked me to give a keynote address, I felt it might be in order to review some of the practices and techniques used in tunneling and work up to some of the concepts now used to mine and construct tunnels. Needless to say, there have been many changes in tunneling technology and also many changes in the Safety Codes controling them. An example of this latter change was the fact that in 1931, my father excavated the Owyhee Tunnel No.5 with gas locomotives. He was able to do it because there was no natural gas in the rock and the ventilation system was designed to free the tunnel atmosphere from powder and exhaust fumes. Today OSHA rules would never permit gas locomotives underground, although there were no incidents on this particular project. One of my first tunnels, as Project Manager, was the Clear Creek Tunnel for the Bureau of Reclamation. Our method of handling muck was the Conway Muckers. This unit was a valuable improvement to the hand mucking of previous generations. The Conway was also used in our Navajo Project, in New Mexico. Unlike the Clear Creek project, where water was one of our main problems - up to 7,200 gallons per minute, at a pressure of 395 pounds per square inch - in the Navajo Tunnel, we had a mixed face which caused a major problem with our support system. In one of the Navajo Tunnels, there was a major cave-in, when the squeezing shale came in during an attempt to strengthen the support system. Although moving shale was not a constant problem, there were areas where the shale was five to six feet above the spring line.

Jan 1, 1976

By V. C. Koppe, J. F. C. L. Costa, D. M. Marques, A. Amaral

Errors associated with estimating the grade of an attribute of interest in a deposit can compromise planning, sequencing, and mineral beneficiation decisions. Several factors are associated with estimation errors. Among them, we can highlight the factors associated with sample spacing, the size of production volumes, and the variability of the attribute considered in the estimation. The access to estimation error can be obtained by some geostatistical methods, for example, by stochastic simulation. However, this is a process that in some situations is computer intensive and takes time. Previous works have proposed a simplified method to access the Maximum Estimation Error (MEE) associated with different types of grade variables, depending on the sample spacing, at small production volumes and considering specific coefficients of variation ranges. This paper presents an approach to assess the MEE associated with long-term volumes. Considering the methodology proposed, it is possible to approximate if a specific drilling pattern used in a deposit provides an acceptable pre-determined estimation error for Resource Classification. Results and considerations on the impact of the geometry of larger production volumes on the MEE calculation are also presented.

Jun 25, 2023

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By H. Cho

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal organic components could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation is dependent on the history of coal: the extent of liberation decreased when the size of the primogeniture coal decreased. The liberation of coal macerals was analyzed by examining the Liberation Index. It was seen that although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinitie), these particles were less liberated than the coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1996

By Lloyd W. Trevoy

Commercial production of heavy minerals from plant tailings streams is undergoing study by Syncrude Canada Lrd. When tar sand from an open pit mine is processed and up- graded to synthetic crude oil, heavy minerals can be recovered from the extraction circuit and can be upgraded to provide concentrates of zircon and titanium minerals. The titanium minerals concentrate consisting of a mixture of ilmenite, leucoxene and rutile, could be utilized as recovered or could be upgraded to synthetic rutile. With the construction of further synthetic crude oil plants in Western Canada a large reserve of heavy minerals will become available for utilization.

Jan 1, 1981

By Robert L. Grayson

An application of goal programming (GP) in evaluation of proposed purchases of major mining machinery is presented. It incorporates historical operating data compiled on mechanical delays to production time. The goal programming technique, which is an extension of integer programming, is used to maximize an objective function. The objective function combines the capital budgeting evaluation methods of net present value, payback period, profitability index, and total net earnings as goals weighted according to a management preference. The GP method gives an optimal solution to a multiple-goal problem. A sensitivity analysis is performed to determine the effect of an increased production forecast or a tightened budget on proposal selection.

Jan 1, 1982