Search Documents

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By Keat Chuan Chew, Qiao Yue Tung, Teoh Yaw Poh

"1 INTRODUCTION With a land area of 718 square kilometres housing a population of slightly over 5.4 million, as of 2014 (Department of Statistics Singapore 2015), Singapore is a highly urbanised city. Transport infrastructure is critical to keep the country and economy highly connected and functional as the population in Singapore continues to grow. The importance of a robust transport infrastructure is recognised by the Ministry of Transport in Singapore, which is working towards bringing 8 in 10 households within a 10-minute walk of a train station by 2030 (Ministry of Transport 2015). This gives rise to the rapid expansion of the rail network in highly urbanised Singapore, resulting in more tunnelling work having to be carried out in closer proximity to existing buildings. Such tunnelling work is expectedly more challenging and complex, and if not managed effectively, will impose higher risk to the adjacent buildings. Hence, the Building and Construction Authority (BCA) has implemented specific control measures to mitigate such tunnelling risks and to ensure safety of the public. 2 CHALLENGES FACED BY TUNNELLING WORK IN SINGAPORE 2.1 General Challenges of Tunnelling in Singapore With the increasing densification of the rail network in a highly urbanised setting, rail projects in Singapore are faced with several key challenges. One such construction challenge is constrained construction sites brought about by network intensification. Alongside the growth of the rail network, shown in Figure 1, other infrastructure networks in Singapore are also continuously growing. Underground interchange stations between networks become increasingly common, forcing each underground interchange station to be constructed deeper and in closer proximity to existing buildings (Figure 2). Singapore is not alone in facing this issue. The same can be observed in cities like London, in which its myriad network of subway lines pushes new lines and interchange stations to be constructed deeper."

Jan 1, 2016

By III Sadler

Processing bauxite and clay ores to reduce Iron content to levels low enough for the ores to be suitable raw materials for such products as refractories and abrasives has long been regarded as a diffi9ult problem. Standard magnetic separation processing of the untreated ore has been attempted by previous investigators with only limited success due to the finely divided state and weak magnetic susceptibility of the iron minerals (hematite, geothite, etc.) present in these ores. The new process described in this paper consists of calcining the finely crushed ore at 500 to 800 C and then reducing (with hydrogen, carbon monoxide, etc.) the iron oxides present to magnetite or elemental Iron. The magnetic susceptibility of iron in these forms is enhanced 40-to 100-fold over that of hematitie and is readily removed by simple magnetic separation. Starting with a 2.7% Fe20s Alabama bauxite ore, a 1.5% Fe20s product was produced in one pass through a Davis tube magnetic separator with 95 + % recovery of the iron-free bauxite fraction and a 20% Fe20a magnetic product. These findings suggest that with the addition of light calcination, reduction and magnetic separation steps to the conventional refractory grain production process, the large U.S. reserves of high-iron bauxites could be used.

Jan 1, 1990

By J. C. Stankus

How to quantitatively identify the loads on a square/arch set is a complicated issue in designing the square/arch set in an intersection/entry. From an engineering perspective, understanding the nature and support mechanism of standing support such as a square/arch set can not only help design the support structure to maintain the roof stability, but save the steel materials and costs of manufacturing, labor, and delivery. Based on the design practices in recent years and successful applications in slope bottom intersections, the authors are confident that the concept of interaction and confinement effect between the steel square/arch set and surrounding rocks is critical in designing a proper steel structure to support an intersection/entry. This paper will detail the design concept and its applications in several underground slope bottom intersection designs, reaching the goals of improving roof stability and reducing costs.

Feb 23, 2014

By B. Pesic

This is an extension of the work on recovery of silver and manganese from Ag-Mn ores, and recovery of silver and gallium from flue dust from phosphate industry. Carbon adsorption was considered as the most adequate method for recovery of silver from thiourea leach solutions. For this reason it was decided to examine the characteristics of adsorption of silver on activated carbon. Coconut hard shell activated carbon was used for this study. Ag(TU)2C1 complex was dissolved into thiourea solution to give 2 gpl stock solution. Thy studied parameters were: loading isotherms at 25°C, 35°C, and 45°C, initial kinetics as a function of thiourea concentration, temperature, pH, N2, and O2. It was found that the loading capacity of carbon for silver and thiourea was 137-150 mg/g and 514 mg/g, respectively, at 25 °C.

Jan 1, 1986

By Terry Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. Cyprus Amax's interest in Russia began before the mid-1991 breakup of the former Soviet Union. In 1990, Cyprus Amax began searching for such an opportunity. Early this year, production will begin at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1.75-kt/d (1,930-stpd) open-pit operation that will produce more than 9.3 t/a (300,000 oz/year) of gold. Identifying Russian mining opportunities In late 1990, the first Cyprus Amax people travelled to Russia. The trip was to determine the potential for western firms to develop profitable mines. This encouraging visit suggested that Cyprus Amax focus on the Russian Far East with its mineral riches and its easier access to the United States. The company's initial efforts thus focused on working with the Soviet Union's Northeast Geologic Expedition, the then government agency for exploration and geology in Russia's Far East. After the breakup of the Soviet Union, Cyprus Amax continued working with the same people, but they now represented new independent, nongovernmental entities. For three years, Cyprus Amax investigated numerous deposits. This resulted in the identification of two properties of significant interest, one of which was Kubaka. Location Kubaka is located in the Northern Evensk District of the Magadan Oblast in the Russian Far East. This is an area east of Siberia. The project is situated in a mountainous area of the Kolyma Range, about 300 km (985 miles) south of the Arctic Circle. It is 285 km (180 miles) north of the fishing village of Evensk and 380 km (235 miles) northeast of the silver-mining town Omsukchan. The site is 950 km (590 miles) northeast of the regional capital city of Magadan. Magadan, the political and economic center of the Oblast, has a population of about 150,000 people. It is served by a year-round deep-water port (with icebreaker assist) and an international airport with service to Moscow and Anchorage, AK. Access to the Magadan region

Jan 1, 1997

By John W. Motter

The Green Mountain Copper Prospect is an unusual stratiform base metal occurrence located in the California Foothills Copper-Zinc Belt. Mined for rich secondary oxide-carbonate ores since 1863, the first serious exploration of the primary ores was in the 1970's. Unlike typical volcanogenic deposits of the district, stratigraphy consists of greywackes overlain (?) or intruded by an intermediate to felsic volcanic unit. Shales and siltstones overlie the volcanic unit. Massive pyrrhotite, chalcopyrite and sphalerite occur at the top of the volcanic unit. Later intrusion and deformation metamorphosed the sequence and created a SW plunging anticline. Characteristic magnetic and electrical geophysical signatures are present and reviewed.

Jan 1, 1978

By G. Wang

With the depletion of easy-to-treat phosphate resources, low quality phosphate ores with high carbonates, particularly dolomite impurities have to be mined to meet the agricultural demand because of the continued growth of world population. The separation of dolomite from phosphate has been recognized as one of the most difficult subjects in mineral processing due to the similarities in their physical and chemical properties. Flotation is considered the most important approach for beneficiating both easy-to-treat and high impurity phosphate resources. There is no doubt that the development of reagents is the key for achieving satisfactory separation performance through flotation process. In order to separate dolomite from phosphate, Arr-Maz Custom Chemicals has made great efforts in developing flotation reagents for removal of carbonates from phosphate ores of different origins worldwide. This paper describes some flotation reagents and processes for the separation of dolomite or/and calcite impurities from phosphate in the ores from different locations.

Jan 1, 2010

By J. R. Muhm

Environmental due diligence investigations, also known as Phase I Environmental Audits, are increasingly important to major investors, venture partners, or prospective purchasers or sellers of mineral properties. Knowledge of environmental risks associated with a property will allow better appraisal of a property's overall desirability prior to completing the transaction. It is possible that the cost of environmental cleanup could exceed the value of the property. Topics appropriately investigated include permit status, water quality, past use of the property, hazardous materials management, storage tanks, public records pertaining to the environmental character of the property, and environmental costs.

Jan 1, 1991

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By P. Knudsen, S. Rosenthal

INTRODUCTION In 2010, Montana Tech was gifted 65 acres of land immediately west of the campus. The parcel of land included an old silver mine called the Orphan Boy Mine. The Orphan Boy and its sister, Orphan Girl, were developed about1895 and operated until 1956. In addition to the gift of land, a significant industry gift was obtained to develop a first class training facility, which we call the Underground Mine Education Center (UMEC). The UMEC has been funded primarily by industry through donations of dollars, equipment, and supplies. The UMEC is a unique hands-on, educational environment for today’s students who are being trained to find, develop and process the worlds' natural resources. The center complements courses in mining engineering, geological engineering, environmental engineering, metallurgical engineering and occupational safety and health. It also serves as a as research facility utilized by students and faculty, and other organizations interested in doing research a hard rock underground mine. LOCATION The Orphan Boy and Orphan Girl Mine are located approximately 700 feet (ft.) apart and the Orphan Girl Mine is part of the World Museum of Mining. Underground they are connected on various levels and all levels below the 100 ft. level are currently flooded. The Orphan Boy mine was 804 ft. deep and Orphan Girl was 3200 ft. deep. The surface locations of the two mines and some of the underground workings on the 100 ft. level are shown on Figure 1 (2015). CONSTRUCTION Land ownership was gifted from BP/ARCO in 2010 and planning started immediately. In June of 2011, site development for the decline to the 100 ft. Level of the Orphan Boy began with a satisfactory portal site developed (Figure 2). We hoped to be able to start driving the decline in July. However, the portal was sited approximately 125 ft. away from a natural gas line that bisected the Montana Tech campus. While outside the right of way for the line, Northwestern Energy requested that no blasting be performed near the gas line until such time as the gas line was abandoned in the fall so decline development was put on hold. The gas line was officially abandoned in January of 2012.

Jan 1, 2019

By V. R. Degner

The minerals industry trend toward very flotation machines, exceeding 10 m3, began in the late 1960's and responds to the continuing desire to achieve better plant economics through improved plant floor-space utilization, power requirements, and operational /maintenance manpower heeds. In general, as process design tonnage increases, the benefits of the larger flotation machine becomes more evident. The development of the larger flotation machine can be distingushed from earlier, smaller, machines in demanding a rational "scale-up" procedure to guide the basic design, thereby producing a machine prototype capable of satisfactory-operational evaluation at minimum cost. Proven flotation machine "hydrodynamic" scale-up consideration, successfully applied in the development of both the WEMCO No. 164 (28.3 m3) and No. 190 (42.5 m3) machine will be reviewed, and the resulting economic benefits of large flotation machines in high tonnage applications will be summarized.

Jan 1, 1985

By Samuel Polinsky, Lawrence W. Bierman, Wayne Perkins

[A column float beneficiation plant using 9, 8.5 foot diameter, cells was constructed by the Simplot Company and the Smoky Canyon Facility in the fall of 1986 and has been in operation since May of 1987. The float beneficiation process was developed jointly by the Simplot Company and the Bureau of Mines (Salt Lake City, Utah) which incorporates the Bureau's bubble generator design and chemistry system based around the reverse float technology, (Albany Bureau of Mines, Application of Carbonate-Silica Flotation Techniques to Western Phosphate Materials, Rule, Dallenbach , Larsen, RI8728, 1982) . This chemistry has been modified by Simplot in both patented and unpatented improvements. The objective of the beneficiation process was to reducethe A1203 content in the overall pipeline concentrate by 0.2 wt z. Therefore, a process stream was identified in the mill circuit which provided an opportunity to isolate and treat 1100 tons per day of poor quality phosphate concentrates The process allows recovery of approximately 15% of the mill concentrates, otherwise unsuitable for fertilizer production. The alternative would have been to waste this ore. Wasting would have resulted in considerable ore loss, increased mining costs and required additional products grinding. ]

Jan 1, 1989

By G. A. Kordosky

There are a number of reasons why the solvent extraction of molybdenum deserves attention: 1. The solvent extraction chemistry of molybdenum is interesting and complex, 2. The price of molybdenum is predicted to average about US$ 20.00 / pound in 2010 and, as China, India and other countries develop, the demand for specialty steels will increase putting long term demands on molybdenum supply, 3. Uranium ores often contain significant concentrations of molybdenum[1] and typically yellow cake will have a moly specification which when exceeded brings penalties, and 4. The valuable metal rhenium is a byproduct of molybdenum recovery circuits.

Jan 1, 2010

Conventional wisdom in the mineral processing industry leads one to believe that pressure oxidation of refractory carbonaceous (preg-robbing) ores is not a practical approach to process development. Initial acid pressure oxidation testing on carbonaceous sulfide ores at the Twin Creeks Mine supported this conventional wisdom. After testing other refractory process options, including air and oxygen enriched roasting, Santa Fe Pacific Gold decided to take a second look at pressure oxidation, using conditions outside the normal range of conventional practice. A combination of very fine grinding and high operating temperature and pressure resulted in significant increases in gold extraction. This paper details the effect of operating parameters developed for Twin Creeks on gold recovery, sulfur oxidation, carbon oxidation/passivation and preg-robb through the laboratory and pilot plant investigations.

Jan 1, 1995

By T. J. Smolik

The Golden Sunlight Mine started full-scale operations in February 1983, with a conventional open-pit mine supplying 4464 tonnes (5000 tons) per day of milling ore. After crushing and grinding, the ore is leached with cyanide solution in large agitation tanks. Soluble gold values are removed from the sand portion of the leached ore with five stages of countercurrent washing cyclones. After thickening of the cyclone-wash overflow slurry, the gold is recovered in activated carbon with a six-stage carbon-in-pulp circuit and a five-stage upflow carbon column circuit. Pressure stripping, carbon reactivation, electro-winning and refining complete the gold recovery process.

Jan 1, 1984

By Guy T. McBride

Mr. Chairman, Fellow Keynoters, Ladies, and Gentlemen: It is purposed to consider the theme of this meeting, "The 1970's - Pivotal Decade for the Mineral Industries," from the particular -- some would say peculiar -- point of view of one engaged in mineral engineering education, and this coign of vantage prompts the textbookish subtitle, "Problems and Solutions (?) in Undergraduate Mineral Engineering Education." Three interrelated problems, or problem areas, will be presented and discussed, and where solutions seem to be emerging or seem worthy to be suggested, they will be identified. The three problems are: 1. The goals, and therefore the course requirements, of the undergraduate curricula are in question, 2. The unit costs of undergraduate education appear excessive to those who bear the charges, and 3. The social ambience of the day affects for the worse the work attitudes and the career motivation of both prospective and in-course students. The Need. - Any discussion of these problems must bottom upon recognized national needs for minerals and a technologically sound minerals industry staffed by competent engineers, particularly at the exploration, development, and production levels, Fortunately, these needs have been recognized and to some extent quantified, and they are even now under further intensive study by some of the most competent members of our society and profession. The latter reference is, of course, to the current work of the National Commission on Materials Policy (U.S.A.) under the executive directorship of Dr. James Boyd. Predating this, and perhaps to some extent

Jan 1, 1972

By Dean Newman, Michael Behrens, Mark Trim, Justin Arifin

Road tunnels in recent infrastructure projects in Sydney, Australia, are designed to have a fire resistance level of either a 4-hour cellulosic fire or a 2-hour hydrocarbon fire. Where permanent ground support for tunnels consists of systematic rock bolts and relatively thin layer of shotcrete, it is important to ensure that during and after the fire event the ground support is designed/predicted not to pose risks to the tunnel occupant. The global behavior of the ground support can be predicted using finite element analysis, and its resistance is derived with consideration of the material strength degradation due to the elevated temperature.

Dec 1, 2022

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994