Search Documents

By M. Batzle

The upper Arkansas basin has some of the greatest potential for geothermal development in Colorado. Over several summers, students conducted an investigation using seismic, gravity, and magnetics in order to help identify the large structures and basin fill associated with the Rio Grande Rift. Adjacent to Mount Princeton Hot Springs, near surface geophysics was conducted to help understand the faulting and fractures that act as a conduit for hydrothermal flow. The methods used included high frequency 3D seismic, magnetics, gravity, D.C. resistivity, and self potential. Throughout the Mount Princeton area, passive seismic, vertical seismic profiling, and well logging were also used to better understand the geology and activity of the region. The results indicate for the area northwest of the hot springs, a 40 to 50 m thick unconsolidated layer overlying the fractured granitic basement. The DC profile shows a deep geothermal anomaly of low resistivity which correlates with a positive SP anomaly in the same region. In the Chalk Creek valley, a shear zone extends from the north east to the south west, just south of the Chalk Cliffs. There appears to be an upward migration of the water through this shear zone which then flows along the porous sediments towards the south in this area. The deep seismic data collected in the center of the basin suggests that the depth to the basement is approximately 2000m. Also identified on the deep seismic are two major faults on the west end and two minors at the east end of the cross-section. An alteration zone is identified between the faults and a possible Precambrian northeast trending shear zone. The potential for developing an Enhanced Geothermal System (EGS) near the center of the valley is high. Our geophysical results indicate a deep basin fill near the center of the basin providing high temperatures. The range front (Sawatch) fault is observed to penetrate under the center of the basin and is an attractive target for natural fractures.

Jan 1, 2011

By k. Osei-Boakye

This paper presents the calibration of a real-time aerosol monitor, the TSI DustTrak?, to the NIOSH 5040 method being used by the Mine Safety and Health Administration (MSHA) for compliance enforcement evaluation. The standard NIOSH 5040 instrument for compliance evaluation of diesel particulate matter (DPM) has an inherent time lag of up to two weeks for laboratory processing of sample results. Therefore, providing the underground mines with a means of quantifying DPM conditions in real-time, will enable them to efficiently and effectively manage DPM levels to ensure compliance with the regulated limit.

Jan 1, 2009

In recent years there have been significant advances in computing power and programming technology, enabling more complicated processes to be modelled in greater detail. This has led to increased understanding of these complex processes, including mineral processing circuits. JKSimMet was developed over the past 35 years, incorporating outcomes from various research projects conducted at the Julius Kruttschnitt Mineral Research Centre (JKMRC), part of the Sustainable Minerals Institute at The University of Queensland. It is a steady-state software program that allows the user to mass balance, model fit and simulate crushing, grinding and classification circuits. JKSimFloat has been developed over the past 20 years, incorporating outcomes from the JKMRC and other institutions around the world through the AMIRA International P9 project ? The Optimisation and Simulation of Mineral Processing Circuits. It is also a steady-state software program, similar to JKSimMet, but is focused on analysing flotation circuits. Both programs have been used in a wide variety of optimisation and design projects over many years. This paper provides an overview of both JKSimMet and JKSimFloat and examples of how both programs have been used to better understand, develop and optimise mineral processing circuits around the world.

Feb 27, 2013

By Jozef F. Zurawski

Increasingly new interceptors or new Combined Sewer Overflow (CSO) projects require connections to existing tunnels. More often than not, the existing facilities are old, in poor or questionable conditions, without proper construction records or as-built drawings. Many cannot be easily inspected unless major construction effort provides flow by-pass for safe access. This paper provides general guidelines on how to approach the problem of assessing the condition of old tunnels, how to plan and design the connection with limited physical assessment, how to develop the scope of work for the bid documents and how to provide geotechnical guidelines and designs for the bid documents.

Jan 1, 2008

By A. Adu-Acheampong

A geotechnical study was conducted to identify the cause(s) of stope instability at the Ashanti Mine (Obuasi, Ghana). As part of the investigation, laboratory testing of rock was performed and the rock mass was classified according to the Q-System (Barton et al., 1974).Numerical analyses were performed using the computer program FLAC (Itasca, 2001). The observed failure zone around the stopes was simulated using both Mohr-Coulomb and Hoek-Brown (Sheorey,1997) models. Yielding along peripheral graphite bands and tensile failure were clearly identified to be the major contributors to stope instability.

Jan 1, 2003

By B. Boberg

Annual requirements of uranium to fuel the 441 currently operating nuclear reactors in the world is 170 million pounds U3O8 (65,385 tonnes U). 2005 global production was 108 million pounds (41,595 t U), of which only 2.7 million pounds U3O8 (1,039 t U), was produced from US uranium deposits. US nuclear utilities represent 26% of the global nuclear capacity but only obtain 2.5% of their supply from US uranium mines. Since 2002 annual global production increased from 93 million pounds U3O8, a 15% increase and the US production increased from 2.3 million pounds to 2.7 million pounds, a 17% increase. Reasonably Assured Resources (RAR) of 12,332 million pounds U3O8 (4.7 million t U) are reported from a wide variety of countries and types of uranium deposits. This RAR suggests that there are significant global uranium resources potentially producible at a price of $50 per pound U3O8 ($130 per kg U). Table 1 shows the distribution of global uranium resources. This table, prepared from historic data maintained by the World Nuclear Association, does not include some areas of the world that are currently considered to contain significant resources of uranium such as Mongolia. Table 1 suggests that the United States contains the fourth largest uranium resource in the world with 890 million pounds U3O8, behind Australia, Kazakhstan and Canada in resources that are producible at a price of $50 per pound U3O8 ($130 per kg U). Within the US, the states that demonstrate the greatest amount of uranium resource are Wyoming, New Mexico, Texas and the Four Corners Area of Arizona, Colorado and Utah.

Jan 1, 2007

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operation, and critical in emergency conditions. This was evident during recent incidents at underground coal mines worldwide. Communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act of 2006. Evaluating the performance of these systems has proven to be dif?cult for mine operators, system manufacturers and regulatory agencies. The MINER Act requires operators to improve accident preparedness by developing an emergency response plan speci?c to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the U.S. Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky feeder communication systems. ? Fixed node-based communications and/or tracking systems. ? Wireless node-based communications and/or tracking systems. ? Medium frequency (MF) communication systems. ? Communication system peripherals. Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include through-the-earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial and hybrid technologies. To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is a need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By Claudio Flores Martinez

The prospect of accomplishing economically and scientifically profitable deep-sea mineral mining within this decade or the next one is of particular interest to the emerging discipline of astrobiology which is concerned with the origin, distribution and future of life in the Universe. Several planetary bodies within our own Solar System such as Jupiter’s moon Europa and Saturn’s Enceladus now appear to be potentially habitable, or life-friendly, in terms of the three prerequisites for life as we know it: a sustained body of liquid water, biogenic elements (C, H, N, O, P, S) and energy sources to fuel metabolic reactions. Europa, for instance, possesses a global subsurface ocean, believed to be up to 100 km in depth, hidden beneath a kilometer-wide ice-sheet. A silicate mantle is directly interacting with a cold, aphotic ocean in which tidal forces might drive geological seafloor activity that results in the creation of hydrothermal systems. These locales are commonly hypothesized to be the cradles for an alternate origin of life on Europa. Especially alkaline hydrothermal springs, as found at Lost City, have been at the center of modeling the prebiological evolutionary dynamics preceding cellular life. Serpentinization-like reactions are also possibly fueling metabolic networks in putative microbial communities found in the oceans of the icy moos. Major space agencies around the globe are planning future space missions aimed at exploring and eventually characterizing potential life forms in these habitats. The technology needed for this exploration effort resembles the requirements for a successful deep-sea mineral mining industry: highly efficient AUVs (also equipped with biologically-oriented instrumentation), swarm robotics, landers, seafloor rovers and general high-pressure, cold temperature extreme environment engineering. Interestingly, science questions of deep-sea mineral mining and astrobiology converge too: the hypothesis of life originating at hydrothermal systems, the biogeographical distribution of species among these environments, adaptations of extremophilic organisms across the three domains of life and adequate autonomous robotic systems to assess the complexity of deep-sea biological communities. This presentation attempts to present a two-fold view of advanced planetary exploration that relates to a sustainable vision of deep-sea mineral mining: charting our oceans and developing technologies least harmful to endemic biology can propel the design and prototyping of future robotic planetary probes bound for aquatic missions on alien moons. Space industry, government and public interest towards a broadened planetary perspective on deep-sea mineral mining is promoted by addressing an astrobiological rationale of this endeavor.

Sep 1, 2014

By F. M. McEvoy, E. J. Steadman, R. Murfin

In England, the provision of aggregate is determined by the historical relationship between construction and aggregate consumption. This approach does not necessarily lead to sustainable decision-making and can be seen as being driven by political expediency, rather than reasonable environmental consideration. The introduction of the statutory requirement for Strategic Environmental Assessment (SEA) in the UK has provided the opportunity to examine this issue on a more rational basis. This paper provides a practical application of a SEA based approach, to the provision of aggregates at a regional level. The process, underpinned by relevant information on resources and environmental assets, suggests that alternative supply scenarios for aggregate provision are tested in a transparent, consistent manner with increased genuine stakeholder consultation. It supports a move away from "predict and provide" approaches to one where aggregates are sourced with the best balance of environmental costs and benefits.

Jan 1, 2005

By Alan Zeni

Blind shaft drilling equipment has not changed substantially since the 1970s. Since it resides in a niche market between conventional shaft sinking and raise boring, the relatively small demand has resulted in some stagnation of development. In the 1990s the technology found a larger foothold in foundation and deep piling work for civil construction. WIRTH GmbH from Erkelenz, Germany has been servicing this market for many years with pile top drilling rigs and tools. Frontier-Kemper Constructors, Inc. recently entered into an agreement with WIRTH to develop a new generation of large diameter blind drilling equipment more specifically aimed at mining needs. The, recently completed, DHI-240 is the first rig to apply the most recent technology. This machine made its commercial debut in the fall of 2008. A description of the technology and a short case study of the first project will be described

By A. Korchevskiy

While Russia continues to be a worldwide leader in asbestos production, the environmental and health status around Russian asbestos mines is not well known and understood, internationally. A literature review was performed to evaluate the potential impact of Russian mining operations on mesothelioma incidence rates in the Ural region where the majority of the asbestos deposits are located. Asbestos that has been mined in this region includes chrysotile, crocidolite, and anthophyllite forms. The Nicholson-Peto (1986) model was applied to published exposure data and mesothelioma mortality statistics in different cities and villages of the Ural region to estimate mesothelioma potency factors (KM) for the various associated fiber types. It was demonstrated that mesothelioma potency factors, as determined by Berman and Crump (2008), could be used to predict mesothelioma risks of non-occupationally exposed individuals in locations where either pure chrysotile, or both crocidolite and chrysotile, are mined and milled. A mesothelioma potency factor was calculated for anthophyllite that appeared to be higher than expected based on previously published studies. The highest incidence of mesothelioma was identified in a community close to a crocidolite mine. The study confirms the validity of utilizing current risk models for non-occupationally exposed populations near asbestos mining activities where asbestos exposures are relatively low and provides methods of characterizing mesothelioma risk in the former Soviet republics (FSRs).

Feb 27, 2013

By C. R. Copeland

Combustion processes, comminution and materials handling can generate airborne particulates. Regulation of these particulates by the U.S. Environmental Protection Agency (U.S. EPA) is becoming progressively more stringent, and regulations will soon include ?nanoparticulates,? which are particles finer than 100 nanometers (0.1 mm). Nanoparticulates are believed to have significant negative health effects due to their high surface area and reactivity. Although it was argued that nanoparticulate concerns were only important for combustion, studies at Michigan Technological University have shown that materials handling and comminution release significant quantities of nanoparticles into the air. Laboratory studies have shown that the use of sodium metasilicate reduced airborne particles finer than 10 mm (PM10) by 86% and particles finer than 2.5 mm (PM2.5) by 80% for iron ore. Additional studies were conducted that revealed that nanoparticulate emissions were present in the types of operations conducted at pyrometallurgical facilities.

Jan 1, 2008

By Chelsea Woodward

The Spokane Research Laboratory of the National Institute for Occupational Safety and Health has demonstrated a prototype hydrogen-fueled mining vehicle as an alternative to diesel equipment in underground mines. Safety and control systems were added to allow a 70-kW rubber-tired hydrogen vehicle, originally developed by the U. S. Bureau of Mines and Hydrogen Consultants, Inc. (now Hydrogen Components, Inc., of Littleton, CO), to be tested. This work began in late 2000 and culminated with a Mine Safety and Health Administration fire safety review and field tests at the Stillwater Mine in Nye, MT, in 2004.

Jan 1, 2006

The following is a summary of some of the companies that were exhibiting their products and services at MINExpo INTERNATIONAL 2000. Atlas Copco develops, manufactures and markets rock drilling tools, tunneling and mining equipment, and surface and geotechnical drilling equipment. The company provides a line of drilling products, including production drilling rigs, rock reinforcement bolts and rock drills. Atlas Copco’s Boomer is a series of high-capacity drill rigs that provides economy, production capacity and reliability

Jan 1, 2000

By R. P. Stahura

Conveyors are the lifeline of mining and processing operations. They continuously supply materials to and carry finished products and waste away from operations. When conveyors are running at less than maximum efficiency, the operation's productivity is in trouble. Inefficient conveyors suffer carryback, leading to the buildup of materials on idlers and other expensive components. They spill and leak material at loading zones and conveyor transfer points. This causes accumulations that can damage the belt, wear moving components and increase both clean-up labor and maintenance expenses. They wander or mistrack, spilling material and endangering personnel and conveyor components. And through these inefficiencies, they multiply the operation's hidden costs. These added expenses occur in lost production, increased downtime for service and maintenance and replacement costs for prematurely worn equip¬ment. In addition, the attitude that inefficiency is "good enough" is recognized elsewhere in the organization. As a result, other departments relax or operate at less than peak performance. Quality goes down along with employee morale. Costs of inefficient conveyors A key to efficiency is handling a product as few times as is necessary. That means conveyors should be loaded, track true to the unloading point and then be unloaded, all without material escape or waste motion. An inefficient conveyor is often signaled by accumulations of DURT - material that has escaped from the system and is now at large in the plant. This DURT adds costs to an operation that are uncounted and, perhaps, uncountable.

Jan 1, 1992

By O?Connor. D. F.

The ever increasing energy costs associated with mining at depth has become an important issue that needs to be addressed for future sustainable production. Vale Inco Limited?s Creighton Mine being the deepest has the highest energy cost per ton due to the ventilation system requirements. A review of the ventilation systems was undertaken with respect to current practices and identification of opportunities to the practical application of technology that would facilitate energy savings. Energy conservation initiatives such as time of day controls have been implemented; however there still remained some opportunity for further reduction. Based on previous studies that identified opportunities due to actual time spent in the workplace, our mining method and ventilation design, it was determined that Ventilation on Demand (VOD) could provide further additional energy reductions with respect to our auxiliary fans. A pilot project has recently been initiated to apply a Ventilation on Demand concept to two 112 kW auxiliary fans and their related workings located on the 2340m level of Creighton Mine. The project objective is to determine the practical methodology and application of this technology in the field. This project involves the installation of variable frequency drive (VFD) starters on the auxiliary fans to allow variable volume (through speed control) based on demand. The required flow is determined based on equipment and/or personnel via identification tags. The Fans adjust to the flow requirements as measured by flow sensors. Since the fans are sized for the final requirements the required flows can be achieved regardless of system length. Energy savings are realized by supplying only the volumes (power) as required and only when required. This paper discusses the rational and program being tested at the VALE Inco Limited, Creighton Mine.

Jan 1, 2009

By A. Sadik

The proliferations of media sources and non-profits organizations in Ghana have put the negative impacts of mining on the ?spot?; this has resulted in public outcry about mining. Although, the gold mining industry has responded by implementing several voluntary measures to ensure sustainable mineral development, these critics label such measures as ?green wash?. In this study, a content analysis of newspaper articles of the Ghana Web Database was carried out after the collection of a total of approximately 900 newspaper articles from it. The data were statistically analyzed to chronologically examine the main media view points and the changing perception of mining issues as reported by private and public media. The results showed government, mining industry (Gold), illegal miners and non-profit & community groups as the main media view points and total of twenty-eight related gold mining sustainability issues. The findings of this study could be used by the gold mining companies to improve upon the communications of their unknown sustainable mineral development measures and to design effective communications and education programs for the public.

Jan 1, 2009

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By L. M. Lenahan, J. D. Sheets

INTRODUCTION The Raleigh-Durham International Airport (RDU) in North Carolina is the fourth largest airport in the southeast region of the United States. The Raleigh-Durham Airport Authority is currently underway with planning, designing and constructing are placement Passenger Terminal as part of the Major Capital Improvements Program at Raleigh Durham International Airport. The Terminal C Expansion and Renovation Project will replace the existing Terminal C structure with a new processor building and concourse. The project is separated into several contracts. The early stage contracts are constructing a west side storm water management facility, relocating taxiways, installing new drainage systems, installing new aircraft apron pavement, Demolition, the Central Energy Plant and Early Foundations. The later projects are the Terminal Building, Passenger Boarding Bridges, Information Technology Systems and Integration, Furniture, Furnishings & Equipment and Specialty Millwork. The Terminal Building will be constructed in two phases. Phase 1 constructs the north half of the new terminal. Airline operations will move to the new terminal at the completion of this phase. Phase 2 completes construction of the south processor building. The full build out of the project, subject to funding availability, will replace the remainder of the south concourse. The Program’s primary focus is to replace the existing passenger Terminal C with a new terminal that will provide more passenger gates and larger passenger screening, ticketing and baggage handling facilities. The planning for the New Terminal C Program began in 2002 with construction starting in March, 2003. The continuing growth of passenger airline travel in the Raleigh/Durham metropolitan area requires RDU to expand its facilities to keep up with the present and future growth within the Region. In October of 2002, the RDU Airport Authority selected Parsons Transportation Group as the Program Manager/Construction Manager to help assist in the development of the Terminal C expansion program. RDU Airport Authority selected the Seattle Washington Office of URS Corporation as the Engineer of Record for the West Side Storm Water Management Facilities. The Westside Storm Water Management Facilities Project became one of the early critical path activities of the overall RDUAA Terminal C Expansion Program. The Briar Creek Reservoir had been constructed to accommodate storm water runoff to the west of the Airport. The existing 1.5 m culvert that drained runoff from the airport terminal (area) to the reservoir was insufficient in supporting the additional flows

Jan 1, 2005