Search Documents

By Simon St J Tose

The objective of this paper and presentation is to review the different criteria and methodology used by AEL and other organisations to create a pre-split design which delivers a stable highwall for the life of that part of the mining operation. It will look at the need to adapt and change the way, size and direction of the production blasts as the mining phase approaches the highwall position for which a pre-split has been created. Key Words: Pre-split: Design; Highwall; Perimeter

Jan 1, 2006

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

By V. C. Kelessidis

The interaction between rock and drill bit during drilling has been modeled for many years, but a complete understanding of the phenomena occurring has yet to materialize. Successful models will allow the prediction of rate of penetration in a given environment and optimal selection of drill bit and drilling parameters, thus minimizing exploration costs. In most rock-drilling models the value of the unconfined compressive strength of the rock (UCS) is used in the predictive equations, within the concept of specific energy, and the value of UCS is the percentage of the value of the stress applied on the drilling bit in order for the bit to advance. While the exact percentage depends on the model used and it is not known with certainty, good knowledge of UCS is nevertheless required before any decent prediction can be made on rate of penetration. Determination of UCS, normally done via destructive testing, requires not only the availability of sound rock core samples but also expensive testing and significant time for the test, which frequently are not available for routine drillability predictions. Hence, a multitude of methods and techniques has been proposed for estimating UCS from various indirect and/or non-destructive measurements, or combination of measurements with neural networks, such as point load index, block punch index, unit weight, and apparent porosity, water absorption by weight, sonic velocity, and Schmidt hardness. The many proposed approaches are critically reviewed and the results are compared, and what becomes apparent is that after many years, not only in mining but also in oil-well drilling, accurate indirect determination of UCS is still an elusive goal. An equation to predict UCS from sonic velocity data is suggested based on several data sets reported in the literature. Use of the specific energy equation with UCS or sonic data and utilization of drilling data allows an estimation of the efficiency of energy transfer from the bit to the rock and of the friction coefficient. Analysis of data reported in the literature, both from laboratory and field studies, has shown that this approach is sound and enables the determination of energy transfer efficiencies and friction coefficients, which for the cases studied range between 15 and 30% and 0.15 and 0.30 respectively. Thus, the suggested data analysis approach allows drillers to focus on inefficiencies and optimize drilling practices in future campaigns. Keywords Rock drillability, unconfined compressive strength, prediction.

Jan 1, 2011

By Y. M. Zhao

The separating performance of a pilot dry beneficiation system using a gas-solid fluidized bed was investigated with coal from South Africa. The coal used for the study has a low inherent moisture content, a moderate ash content, a moderate volatile content, a low sulphur content and a high calorific value. Its washability is moderate. Experimental results show that the separating quality of the fluidized bed drops gradually as the feed-coal particle size decreases. The probable error, E, values for 50?25mm, 25?13 mm and 13?6 mm coals were 0.04 g/cm3, 0.06 g/cm3 and 0.09 g/cm3, respectively. The cause of the differences in separating characteristics was analysed by particle dynamics and numerical modelling. Furthermore, the pilot fluidized bed was employed to separate 50-6mm coal. In this experiment the coal ash content was reduced from 23.74% to 11.79%, with a probable error, E, value of 0.07 g/cm3and a recovery efficiency of 98.26%. This indicates that the fluidized bed is applicable to the separation of coal from South Africa and has good separating performance and wide applicability. Keywords: feed-coal particle size; gas-solid fluidized bed; dry coal beneficiation; numerical simulation.

Jan 1, 2010

By A. Swanson

The Australian coal industry has been subdued in recent years and only a few new plants have been constructed, but the drive for greater efficiency has seen continued technological developments. The paper lists the new plants and major upgrades, plus summarizes technical developments in the areas of dense medium processing, fine coal treatment, froth flotation, dewatering and on-line analysers.

Jan 1, 2001

By R. Ordóñez Olivares

This manuscript focuses on the design and development of steels for the railroad industry and methods of testing them. Here are summarized the results of research focusing on alloy development and design, with particular focus on advanced rails and wheels. The high-performance steels are characterized for their mechanical and service characteristics. The relationship between properties and cleanliness is discussed and compared to the regular railroad steel. Some of the tests presented are standard tests that are complemented with the nonstandard test recommended by the Association of American Railroads (AAR) and recommended modifications of this. The paper presents the results of metallurgical analysis, mechanical, and residual stress tests. The laboratory methods include microstructure, residual stresses, tensile, hardness, fracture toughness, and microcleanliness tests.

Jan 1, 2013

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By M. Sanchez, C. Morales, J. Palacios

The slag produced in the Peirce Smith converters at the Ilo smelter of Southern Peru Copper Corporation has shown a wide range of magnetite content, which introduces an additional problem in the smelting units due to materials? recirculation. However, the operation data analysis and the application of thermodynamic concepts have made it possible to produce slag with magnetite content between 18 and 20%. The results have suggested that matte grade enhances magnetite formation while silica controls its precipitation, and they are also influenced by the increasing temperature of the slag. Thus, in order to obtain the required magnetite content in the slag, matte grade is gradually enriched in equilibrium with slag containing from 25 to 32% silica.

Jan 1, 2004

In this study, the effects of slag compositions, slag amount, temperature, and carbon content of steel on the manganese and phosphorus distribution ratios during converter steelmaking were analysed using the classical regular solution theory, and industrial tests were performed using two 80 t top-and-bottom combined blown converters (duplex melting process). The results indicate that the slag amount, temperature, and carbon content in steel are the main factors affecting the manganese yield when converter slag compositions remain constant. The FeO content of the slag has a strong impact on the manganese distribution ratio, while the slag basicity and MgO content have no obvious effect. The calculations and experimental results show that the phosphorus distribution ratio increases sharply with increasing slag basicity R, but then decreases with the increase of MgO and MnO contents in the slag. The final slag in converter steelmaking should have the following characteristics: 3.5 < R < 4.5, 15% < (FeO) < 20%, and 6% < (MgO) < 8%. The slag amount should be controlled appropriately at the same time. The results of this investigation would be useful in deciding on the application of manganese ore in alloying and identifying the slagging regime in converter steelmaking.

Jan 1, 2014

By R. Webber-Youngman

The Department of Mining Engineering at the University of Pretoria accepts that the process of teaching and learning improvement is an ongoing exercise with the ultimate aim to deliver well-rounded mining engineering practitioners. Various challenges impact on the success of this process. An integrated and innovative process was developed and is followed in the Department to overcome these challenges. The aim of the Department is to apply a holistic teaching approach by introducing multiple integrated interventions with regards to teaching and learning strategies. Three phases of this process are discussed in this article, and are illustrated in Figure 1. During the first phase, prior to 1999, several teaching and learning challenges were identified in the Department of Mining Engineering. These challenges are discussed in the next section. In the current phase, a variety of interventions to address the challenges are being developed, implemented (in some cases piloted), and evaluated. The future phases will focus on the improvement, successes, and full roll-out of current interventions, as well as on training, development, and support for all staff members to participate in the process. (Figure 1)

Jan 1, 2011

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

O.F.S. Branch, Welkom Minutes of a Committee Meeting held in the V.LP. Lounge of the Welkom Club on Tuesday, 26th June, 1973, at 5.00 p.m. Present Mr C. J. Isaac (in the Chair), Mr D. A. Smith, Mr G. Young,

Jan 1, 1974

By P. M. Cole

An unprecedented expansion of the global zinc industry is currently under way. While most new projects and plant upgrades remain committed to traditional processing technologies, recent advances in zinc solvent extraction (SX) have created opportunities for new process routes for both primary and secondary materials. The first commercial plant to use zinc SX for the mainstream processing of a low-grade ore is under construction and promises to become one of the lowest cost zinc producers. Several other oxide and sulphide projects in various stages of feasibility are considering the inclusion of SX in their process flowsheet. Zinc SX has also proved advantageous in the reprocessing of secondary materials, particularly for the treatment of zinc residues and furnace dusts. This review focuses on recent installations and projects underdevelopment that feature zinc SZ as the key separation step.

Jan 1, 2002

By S. Dalton

The use of coal for power generation is being questioned in many developed countries, as a result of ever-tightening environmental restrictions and concerns about the potential impact of CO2emissions on climate. Coal will continue to be the fuel of choice for new power plants for many developing countries with large percentages of the world?s population, because of its relatively low cost and broad availability. Even in many of the developed countries that are under pressure, coal will continue to fuel large percentages of power due to the installed base. Using coal efficiently and in an environmentally responsible manner will be a challenge for technology and politics in this new century, with the politics played out on the world stage. Coal use will vary in the next few decades, including short-term changes such as the use of more diverse coals and the increased use of efficient ultra-supercritical boilers to longer term ?refining? of coal to produce a range of energy and chemical outputs. This paper outlines EPRI?s Global Coal Initiative aimed at needed developments and demonstrations that support the long-term vision of environmentally sound and economical coal use for power generation, and discusses some of the forces that are driving this development effort.

Jan 1, 2001

By T. Khumalo, L. P. Coetzer

This paper addresses the impact of the variable speed drive on the particle size distribution in the product of a fully autogenous UG2 grinding circuit. It further discusses the impact of a varying particle size distribution in the product of the mill on the downstream classification and milling circuits. An industrial case study was used and data is presented to illustrate the techniques applied to identify the root cause of the shift in operational efficiency. The results achieved from both the investigation into the shift in plant efficiency and the sub-sequent corrective action taken illustrate that the root-cause methodology used in advance control can be effectively applied on production sites to both detect the shift and identify probable root-causes. The industrial example used confirms that the variable speed drive in a UG2 autogenous milling operation is a critical control parameter to ensure that the plant operates to design specifications.

Jan 1, 2006

Often plant performance suffers as a result of poor control. Poor control leads to low mill throughputs, poor classification and less than satisfactory concentrate grades and overall recoveries. By using the appropriate control tools, substantial gains in plant performance can be made. Mintek?s MillStar and FloatStar controllers have been implemented at various sites across the world. The MillStar controller incorporates leading technology that controls process units from the mill feed through to the flotation feed. Typical results show that milling circuit throughput is increased by 6-10 % and the final product grind size is tightly controlled, thereby enhancing flotation performance. The FloatStar controller is aimed at stabilising and optimising flotation circuits. Through improved level control alone, recovery improvements of up to 1 % have been achieved. Furthermore, by using on-line grade analysers, the controller stabilises final concentrate grades, whilst maximising flotation recovery.

Jan 1, 2005

By D. K. Chibwe, P. Taskinen

"This investigation consists of a numerical and physical modelling exercise on flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a 0.2-scale cold model of an industrial Peirce-Smith converter (PSC). Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The 2D and 3D numerical simulations were carried out using volume of fluid (VOF) and realizable k-e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions. Measurement of mass transfer indicated that fluid flow in the PSC is stratified. Blowing configurations and slag volume both had significant effects on mixing propagation, wave formation, and splashing.As a potential process alternative to increase conversion efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined as well as lateral blowing conditions, and the results of the combined concept are encouraging."

Jan 1, 2015

By S. Bellec

A leaching model for gold ore that takes into account the impact of cyanide and oxygen concentrations as well as gold surface exposure on leaching performance is developed. Cyanide consumption is estimated by an empirical model that is a function of ore particles size distribution as well as cyanide, copper and sulphur concentrations. The proposed model has been validated by data from laboratory leaching tests on the Sleeping Giant gold mine ore. Keywords: gold leaching, modelling, exposure surface.

Jan 1, 2009

The processes by which particles and bubbles interact capture many of the central concepts of colloid science and hydrodynamics. This area of research embraces hydrodynamics, interfacial(including capillary) forces, particle and bubble behaviour and solution chemistry. In this review, we discuss collision, attachment and stability efficiencies. We deal with the identification of a flotation ?domain?, the deformation of a bubble surface upon interaction with a solid surface, the kinetics of three phase contact line expansion and the determination of attachment efficiencies through to the direct measurement of bubble-particle interaction forces. We have recently carried out a test of collision theory where the latter embraces both inertial and centrifugal forces. The real challenge is now to quantitatively describe the behaviour of real systems and to incorporate a reliable description of the behaviour of particles in flotation froths. The approach described is very robust when applied to flotation, both from qualitative and quantitative points of view, providing an intellectual foundation for understanding this complex process in separation science and technology.

Jan 1, 1999